FCC ID: 2ASJR-LYNXFLEET-22L ML5 Asset Tracker

ML5 Asset Tracker Instructions for Installing the Telematics Module For use with a ML5 controller only Tools Required:

1) Phillips/Flat screwdriver 2) Wire tie cutter 3) Silicone Caulk 4) Surface Cleaner (Isopropyl Alcohol) This instruction should be read through completely before proceeding. WARNING Power the unit on and update the ML5 controller software to the currently released ML5 software (6320+) for the PrimeLINE models. Set the controller date and time in GMT. You may refer to the operations and service manual for detailed explanation. Before proceeding with installation, set ON/OFF switch and circuit breaker to OFF position. Disconnect power plug from the unit. Follow local lockout tagout procedures for working on the equipment. Parts required per assembly:

ITEM PART NUMBER PART NAME QTY 1 2 3 4 5 6 7 8 12-00930-00 58-01441-01 02-00311-02 66-U---13882 62-12305-00 62-11270-32 62-11114-00 98-02739-00 TELEMATICS MODULE AND HARNESS STA-STRAP LUBRICANT WIRE TIE LABEL LABEL,WARNING TAG INSTALL INSTRUCTIONS 1 1 1 12 1 1 1 1 Installation Procedure:

1. Ensure The ML5s software is updated to 6320+ prior to install. 2. Record the information shown in Table 1. If installed in the field, please report the following data to container.lynxfleetsupport@carrier.com. Lynxfleet Device Serial Number Unit S/N Prefix Unit S/N Container Prefix Container No. Comm. Date

(mm/dd/yyy) Controller S/N Software Version Install Location Customer Table 1: LynxFleet Device Warranty Information 3. Open the control box door. See Figure 1. RAIN SHEILD ML5 CONTROLLER CIRCUIT BREAKER

(CB-1) Figure 1: Control Box with Door Open 4. Remove the rain shield by removing the screws using a flat head screwdriver. Temporarily reinstall the two screws to hold display in place for the next step. See Figure 2a and 2b. 5. Clean area of any residue caulk on either the rain shield or the control box door. Figure 2a: Removal of Rain Shield Figure 2b: Screws reinstalled 6. Remove the two lower screws on the display. 7. Position the Telematics module with the flat side of the module facing towards the door and reinstall the two screws on the display to secure / mount the module in place. See Figure 3. Figure 3: Module Installation 8. Note the ground screw location and wire orientation. See Figure 4a. The module may need to be pushed up when tightening it down to clear the ground screw. Figure 4a: Module Installation Figure 4b: Module Installed under rain shield 9. Apply electrical contact dielectric grease to the micro-USB connector on the ML5 and the micro-USB plug. See figure 5b. 10. Plug the micro-USB (item 1) to the ML5 controller connector and secure with the STA-

Strap (item 3) to the USB guard and pull tie wrap to secure USB cable. See Figure 5c and 5d. 11. Locate the existing software tag and remove it from the unit. See figure 5d. 12. Take the clear plastic tag (item 7) and apply new label (item 6). See figure 5d. 13. Secure tag to the USB cable near the controller using wire tie. See figure 5d. 14. The power cable splits into QC and TRX2. Connect the wire marked QC to the QC connector on ML5 controller. See Figure 5e. Figure 5d: Add new warning tag and label (item 7 and 6) here on the USB harness. Remove existing warning tag. Transformer See Figure 6c for installation of TRX2 wire Figure 5b: Lubricant (item 3) to be applied to Micro-USB connection USB Guard Figure 5c: STA-STRAP (item 2 Secure to USB guard Figure 5e: QC connection Figure 5a: Harness Connections 15. Loosen the mounting screws of the filter in front of the transformer using a flathead screwdriver so it can be rotated out of the way. See fig. 6a and 6b. Mounting Screws to be loosened Figure 6a: Filter location Figure 6b: Filter mounting screw 16. Connect the wire marked TRX2 to the low voltage side of transformer at an open X2 connector. See Figure 6c. Step 12 Figure 6c: TRX2 connection to Transformer 17. Move the filter back to its original place and secure it with the mounting screw. 18. With the door fully open, neatly secure the wire harness using the wire ties and securing to existing display cable conduit. See Figure 7a. Figure 7a: Securing wire harness 19. Remove the top screws on the display. Reinstall rain shield using these screws. 20. Caulk along the top of the rain shield to prevent water ingression. See figure 7b. Figure 7b: Caulking of Rain Shield 21. Secure the wire harnesses to the rain shield via the hole as shown below in figure 7c. If there is no hole, drill a hole with a or 6mm drill bit. 22. Clean the rain shield with an appropriate cleaner and add the USB label (item 5) to the rain shield to the right of the harness mounting hole. Location shown in figure 7c. Figure 7c: Routing wire harness and label location 23. Power on the reefer unit. 24. Check the operation of the Telematics Module using the LED display. The LED on the module will display accordingly. NOTE: Ensure there is good cellular coverage for a successful telematics device connection. Standard Startup KEY A= Amber G= Green R= Red A/G/R -> LED ON ~250MS

-> LED OFF ~250MS

-> Pattern repeats On power Battery LED LED Time Startup no LED no LED

< 30 seconds Gateway Connection Check GAGG ----

AGAA ----

Telemetry Ready/Sending G-G- G--- ----

A-A- A--- ----

< 30 seconds With Good Cell signal Warning/Error patterns LED patern Error/Warning description R-R- R-R- R--- ---- SIM Detection ERROR Recommended Action IoT device replacement R-R- R-R- ----

SIM CELL Network Reg ERROR IoT device replacement**

R-R- R-R- ----

R-R- R--- ----

R-R- ----

AAAA ----

GGGG ----

SIM DATA Network Reg ERROR SIM APN ERROR Controller serial number incorrect on ML5 Connection to internet but not to Lynx Fleet IoT device replacement**

IoT device replacement**

ML5 replacement**

Ok; no action required. No LED for more 2 minutes Communication between ML5 controller and Telematics device defective. Step 1: Check Power Supply to ML5 and Telematics Device. Step 2: Check ML5 Connection Step 3:Check ML5 USB port with a flash drive

(data download) if flash drive is detected ML5 is probably fine Return the IoT Gateway If flash drive is not detected, ML5 USB port may have an issue. Try the device on another ML5. Other warning patterns:

Cell signal Marginal NO Cell Signal Action On power Battery LED LED G-G- ----

G--- ----

A-A- ----

Cell signal low or inconsistent:

Data will be stored on device and will be sent when cell coverage is recovered. A--- ----

No cell signal detected -

Data will be stored on device and will be sent when cell coverage is recovered. Move reefer unit to area with better cellular coverage.

** Contact your assigned Carrier Field Service Manager or Lynx Fleet Support prior to any replacement. FCC/CE/ISED Compliance FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation.

(2) Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Title: Telematics Device Instructions. Kits 76-00980-00 Supersedes:

Page: 10 of 11 No.: 98-02739-00 Rev: B Authorization #: ECN1146067 FCC / ISED RF exposure statement:

The equipment complies with FCC & ISED Radiation exposure limit set forth for uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. ISED This device complies with Part 15 of the FCC Rules and contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS standard 247. Operation is subject to the following two conditions:

this device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement CE Warning This equipment should be installed and operated with minimum distance 20cm between the radiator and your body This device in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. All essential radio test suites have been carried out. Used On:

ML5 Controller Units Prepared By:

D. Eager Approved By:

Hoover, Navarro Date:

08/2022 ALL USES AND PUBLICATION RIGHTS RESERVED - PROPERTY OF CARRIER TRANSICOLD, SYRACUSE, NY No.: 98-02739-00 Rev: B Authorization #: ECN1146067 Title: Telematics Device Instructions. Kits 76-00980-00 Supersedes:

Page: 11 of 11 CAUTION : RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. Adapter shall be installed near the equipment and shall be easily accessible. The plug considered as disconnect device of adapter. The device complies with RF specifications when the device used at 20mm form your body. 1. 2. 3. SYM REVISION RECORD DATE BY ENGR ECN NO A B C INITIAL RELEASE Updated photos 23 MAY 2022 27 MAY 2022 DE DE ECN1146067 Added FCC/CE Statement 13 OCT 2022 WD Used On:

ML5 Controller Units Prepared By:

D. Eager Approved By:

Hoover, Navarro Date:

08/2022 ALL USES AND PUBLICATION RIGHTS RESERVED - PROPERTY OF CARRIER TRANSICOLD, SYRACUSE, NY

8 7 6 5 4 3 2 CONFIDENTIAL REVISIONS DESCRIPTION REDRAWIN CORRECTED CCID, IMEA, AND Lora ID ON LABEL TEXT, ADDED GT VENDOR CODE TO QR CODE CORRECTED TRANSICOLD SPELLING IN BODY OF LABEL ADDED BACK MISSING VENDOR CODE INFO IN NOTE 10 ON REV-

D OF THIS DRAWING REDRAWN LABEL INFORMATION NEW CARRIER CTD PN & ADDED GT SUPPLIER CODE TO READABLE TEXT, CLARIFIED QR CODE INFORMATION MODIFIED IC NUMBER 03JAN2022 05JAN2022 18JAN2022 04MAR2022 31MAR2022 DATE 09NOV2021 APPROVED JJT 23DEC2021 MB/JJT 50.8 2 9 7 5 NOTES:

1. PARTS TO BE MANUFACTURED IN COMPLIANCE WITH THE MOST CURRENT RoHS &REACH DIRECTIVE. RoHS & REACH DECLARATION MUST BE SUBMITTED WITH THE FIRST ARTICLE INSPECTION SAMPLES, AND RESUBMITTED WHENEVER NEW CHANGES TO THE DIRECTIVES ARE ISSUED. 2. 3. 4. LABEL CONTENT, TEXT, QR CODE AND GRAPHIC SHOWN ARE FOR REFERENCE ONLY, VERIFY CONTENT FOR PRODUCTION. SERIAL NUMBER CONFIGURATION TO BE DESIGNATED AS PER GLOBE TRACKER MANUFACTURING. SERAL NUMBERS, LoRA, CCID ARE TO BE AUTOMATICALLY GENERATED. MANUFACTURING DATE CODE T FOLLOW 4 DIGIT FORMAT 5.

- FIRST 2 DIGITS: MFG YEAR, SECOND 2 DIGITS: MFG WEEK

- EXAMPLE: 2210 (2022, WEEK 10) REV. B C D E F G H THIS FIELD IS TO SPECIFY THE NAME OF THE COUNTRY IN WHICH THE PRODUCT 8 IS BUILT. REVISION TO MATCH THE NUMERICAL REVISION OF THE PRODUCT BUILT PER THE MOST RECENT BOM (EXAMPLE: 1). GRAPHIC IMAGE ASPECT RATIONS MUST BE MAINTAINED. ADDITIONAL VARIANT DEFINED BY VARYING "-00" SUFFIX. 6. 7. 8. 9. 10. QR CODE TO BE MINIMUM 10 mm SQUARE AND CONTAIN THE FOLLOWING ID NUMBERS. WHEN READ, ALL ID NUMBERS NUST BE ON SEPARATE LINES AND IN THE ORDER SHOWN BELOW:

SERIAL NUMBER*

SN0201USD 12-00930-00 REVISION*

CCID*

IMEI*

LoRA ID*

NOTE: *= ID NUMBERS GENERALTED DURING ASSEMBLY SN0201USD= GLOBE TRACKER VENDOR CODE ASSIGNED BY CARRIER IMEI=CELL ID DEV EUI=LoRa ID 11. USE LABEL STOCK GLOBE TRACKER PART NUMBER LAB-0009. 4 DRAWN:

JJT CHECKED:

MB QA:

ES MFG:

MB D C B A CONFIDENTIAL 7 6 5 4 3 APPROVED:

MD MATERIAL:

SEE NOTESS FINISH:

SEE NOTES PART NO. SIZE B SCALE: NONE LAB-0010 16DEC2021 2 REV H SHEET 1 OF 1 1 COPYRIGHT 2021 GLOBE TRACKER ALL RIGHTS RESERVED 6 10 GLOBE TRACKER, ApS CVR#33579004 DK-1401 Copenhagen K, DENMARK G2.6 ML5 CARRIER LYNXFLEET 22L INFORMATION & AGENCY LABEL TOLERANCES EXCEPT WHERE NOTED 1.0 mm 0.5 mm 0:

0.0 0.00:

0.000:

0.25 mm 0.125 mm TITLE ANGULAR:

0.5 DEG UNITS OF MEASURE:

METRIC, mm JJT JJT JJT JJT JJT 3 4 4

. 5 2 1 D C B A Label Location

(Insert Company Letterhead) Letter of Authorization and Anti- Drug Statement Applicant Name: Globe Tracker ApS Address: Strandgade 91, 4th Floor DK-1401 Copenhagen K Denmark Product Name: ML5 Asset Tracker Model Number: LYNXFLEET-22L FCC ID: 2ASJR-LYNXFLEET-22L We authorize:

CETECOM Inc., to act on our behalf on all matters concerning the above named equipment. We declare that CETECOM Inc. is allowed to forward all information related to the approval project to the Federal Communications Commission and discuss any issues concerning the approval application. The applicant must certify that neither the applicant nor any party to the application is subject to a denial of Federal benefits, that include FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47 CFR 1.2002(b) for the definition of a "party" for these purposes. Does the applicant or authorized agent so certify? Yes I certify that I am authorized to sign this application. All of the statements herein and the exhibits attached hereto, are true and correct to the best of my knowledge and belief. In accepting a Grant of Equipment Authorization as a result of the representations made in this application, the applicant is responsible for (1) labeling the equipment with the exact FCC ID specified in this application, (2) compliance statement labeling pursuant to the applicable rules, and (3) compliance of the equipment with the applicable technical rules. If the applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC's technical requirements. Authorizing an agent to sign this application, is done solely at the applicant's discretion;

however, the applicant remains responsible for all statements in this application. If an agent has signed this application on behalf of the applicant, a written letter of authorization which includes information to enable the agent to respond to the above section 5301 (Anti-Drug Abuse) Certification statement has been provided by the applicant. It is understood that the letter of authorization must be submitted to the FCC upon request, and that the FCC reserves the right to contact the applicant directly at any time. Signature of Authorized Person Filing:

Title: Director of Engineering Date: 10/25/2022

Federal Communications Commission Equipment Authorization Division 7435 Oakland Mills Road Columbia, MD 21048 Date: 10/20/2022 Subject:

Request for Permanent Confidentiality FCC ID: 2ASJR-LYNXFLEET-22L To Whom It May Concern:

In accordance with 0.457(d) and 0.459 of CFR 47, and KDB 726920, Globe Tracker ApS hereby requests permanent confidentiality for documents filed under the following exhibit types:

1. Block Diagram 2. Schematic Diagram 3. Part List 4. Operational Description These items contain detailed system and equipment description and related information about the product which Globe Tracker ApS considers to be proprietary, confidential and a custom design which otherwise would not be released to the general public. Since this design is a basis from which future technological products will evolve, Globe Tracker ApS also feels that this information would be of benefit to its competitors, and that the disclosure of the information in these exhibits would give our competitors an unfair advantage in the market. We are aware that exhibit types cover letters, attestations, label document, test reports, RF exposure information (SAR and MPE reports), cannot be requested to be classified confidential and are thus subject to publication, as will be documents of all other exhibits types for which we have not requested a confidentiality classification. Best Regards, _______________________________ Signature Name: Mark Oudshoorn Title: Director of Engineering Company Name: Globe Tracker ApS Address: Strandgade 91, 4th Floor DK-1401 Copenhagen K Denmark

Federal Communications Commission Equipment Authorization Division 7435 Oakland Mills Road Columbia, MD 21048 Date: 10/20/2022 Subject:

Request for Short Term Confidentiality FCC-ID: 2ASJR-LYNXFLEET-22L To Whom It May Concern:

In accordance with 0.457(d) and 0.459 of CFR 47, Globe Tracker ApS hereby requests short term confidentiality for documents filed under the following exhibit types:

1. External Photographs 2. Internal Photographs 3. User / Instruction Manual 4. Test Set-up Photographs until the product will be publicly announced. Short term confidentiality release date / period: 180 days from grant issue date These items contain detailed system and equipment description and related information about the product which Globe Tracker ApS considers to be proprietary, confidential and a custom design which otherwise would not be released to the general public. Since this design is a basis from which future technological products will evolve, Globe Tracker ApS also feels that this information would be of benefit to its competitors, and that the disclosure of the information in these exhibits would give our competitors an unfair advantage in the market. We are informed and aware of our obligation that we have to inform the involved TCB in written and in due time if we intend to market the product prior to the above specified confidentiality release date so that the short term confidentiality classification can be reset prior to product launch. We are aware that exhibit types cover letters, attestations, label document, test reports, RF exposure information (SAR and MPE reports), cannot be requested to be classified confidential and are thus subject to publication, as will be documents of all other exhibits types for which we have not requested a confidentiality classification. Best Regards, ____________________________________ Signature Name: Mark Oudshoorn Title: Director of Engineering Company Name: Globe Tracker ApS Address: Strandgade 91, 4th Floor DK-1401 Copenhagen K Denmark