Safety Instructions and Attentions First of all, as the most basic principle: This product is a professional lighting set equipment and should be used by professional lighting engineers or under the guidance of professionals. Basic safety attentions must always be followed during use, as follows:
1.Before use, please read and understand these instructions and attentions. 2.Professional lighting is prohibited for children. When children are near, parents or accompanying persons must supervise closely to prevent children from personal injury due to collision with lamps or private use of lamps. 3.This lighting product is not ordinary lighting product and cannot be used for general lighting. Anyone who has suffered eye damage or has sensitive eyes should avoid using this product. 4.When the lamp is on, it must be used with care. Do not touch high-temperature parts, such as LED lamp beads, to avoid burns. 5.When the lamp is on, it is forbidden to look directly at the lamp beads under any circumstances. Strong light should be used under the guidance of professional lighting engineers. Avoid prolonged exposure to strong light under any circumstances. If eye discomfort, please turn off the lamp in time, suspend use, and see a doctor immediate-
ly. 6.If the lamp bead is damaged or deformed by heat, stop using this equipment, and contact the manufacturer, service agent or qualied maintenance personnel to replace the lamp bead in time to avoid accidents. 7.This product is only suitable for use in -10 to 40 operating environment and normal humidity environment. 8.Do not use damaged equipment or accessories, and wait for professional maintenance personnel to check and repair to conrm being normal before use. 9.During using, if the casing of this product is broken due to being dropped, squeezed or subjected to strong impact, please do not use it, so as to avoid electric shock injury due to contact with internal electronic components. 10.If an extension cord is required, please use an extension cord with a current rating greater than or equal to that of the equipment. If an extension cord is rated less than the equipment, overheating may result. 11.Some products have long power cords, please place the power cords properly and keep them in a safe place. Avoid contacting the power cord with overheating surfaces, avoid improper placement that could cause pulling damage, or trip on-site personnel. Please use the certied power cord from the original manufacturer. If the product is damaged by using a non-certied power cord, it will not be repaired by our factory. 12.Be sure to unplug equipment from the power outlet before cleaning and repairing. When not in use, do not pull the power cord to unplug the equipment. For normal power-off, please hold both ends of the plug of the equipment with your hands and pull the plug out of power outlet. This equipment needs to be connected to a ground-
ed outlet. 13.This equipment is not waterproof, please keep it dry and do not immerse it in water or other liquids. The equipment should be installed in a dry and ventilated place, and avoid using it in rainy, humid, dusty or overheated environments. Do not place any objects on the lamp or let liquid flow into the lamp to avoid accidents. 14.Do not disassemble the product without permission. If the product fails, it must be checked and repaired by authorized maintenance personnel. 15.Before storing, make sure that the equipment has cooled down completely. For storage, unplug the power cord from the equipment. The equipment should be placed in the carrying case or in a ventilated dry place. 16.Do not place equipment near flammable and volatile solvents such as alcohol and gasoline. 17.Do not use accessories that are not recommended by our factory to avoid re, electric shock or personal injury. 18.When cleaning, do not wipe it with a damp cloth, please use a dry cloth or a soft cloth to wipe the dirt of the equipment. 19.Please take off the protective cover before using. 20.This product complies with ROHSCEKCPSE and FCC certication, please refer to the relevant national standards for use and operation. 21.The safety instructions are formulated according to the strict testing of the factory, and the design and specications of the equipment are subject to change without prior notice. For latest product information, please check the GODOX website and view latest electronic instruction. 22.Some products have built-in lithium batteries. Please use specied chargers, and use them within a proper range of the specied voltage and temperature according to the correct operating instructions. 23.Some products are battery powered. Do not use any batteries, power sources or accessories not specied in the instructions for such products. Keep batteries and other accessories out of the reach of children and infants. In the instance that a child or infant swallows a battery or accessory, immediate emergency medical attention is required. If the battery leaks, becomes discolored, deformed, emits smoke, or emits an abnormal odor, remove it immediately. Be careful during removal to avoid burns. Continued use could result in re, electric shock, or burns. Do not use any deformed or modied batteries. Do not disassemble or modify this product or battery. Do not heat or solder the battery. Keep the battery away from re or water. Do not incorrectly insert the positive and negative ends of batteries, or mix old and new batteries or batteries of different types together. 24.One-year warranty period, accessories such as consumable batteries, adapters, power cords, etc. are not covered by this warranty. 25.If it is found that the equipment is repaired without authorization, the one-year warranty period will be cancelled and relevant fees will be charged for maintenance. 26.Machine failures caused by non-standard operation are not covered by the warranty. keep these instructions!
23 24 Foreword Thank you for purchasing!
Godox M200Bi/M300Bi is a LED Light product with superior performance. It has a separation design of light body and controller, wide color temperature range, high brightness, low consumption, high power, ultra-high CRI and various dimming curves functions, quite suitable for large photo studios, broadcast studios, outdoor or large-scale eld scenes. Features:
Strong power to create bright light output. 0-100 stepless brightness adjustment controls the brightness in subtle scenes. Wide color temperature range from 2800K-6500K 4 dimming curves: linear, S-curve, exponential, and logarithmic. Bowens mount is perfectly compatible with more optical accessories. Various professional control methods: Bluetooth control/DMX512 remote control/2.4G wireless control. Super high color rendering index: CRI96, TLCI97 21simulated light effects: flash, lightning, TV, broken bulb, candle, re, rework, etc. Two power supply methods: AC power supply (100V~240V)and V-mount battery power supply (14.8V or 26V). The side with yellow battery removal button supports unilateral power supply. 2.4 inches TFT panel,4 buttons, 1 knob, clear UI interface. Warning Always keep this product dry. Do not use in rain or in damp conditions. Do not disassemble. Should repairs become necessary, this product must be sent to an authorized maintenance center. Keep out of reach of children. As this product do not have waterproof function, please take measures of waterproof in rainy or damp environment. Do not leave or store the product if the ambient temperature reads over 40C. Do not use the product in the presence of flammable gases, chemicals and other similar materials. CAUTION: Hot parts!When the product is always on and flickering,please do not touch the high temperature part of the LED head. When replacing product accessories,please turn off the LED light and perform a cold cut. The light source contained in this luminaire shall only be replaced by the manufac turer or his service agent or a similar qualied person. The lamp shall be changed if it has become damaged or thermally deformed. The luminaire is intended for professional use only. SAVE THESE INSTRUCTIONS 25 26 Name of Body Light Body 1.Black Battery Removal Button 2.V-mount Battery Box 3.AC INPUT Port 4.48V DC Port 5.Yellow Battery Removal Button 6.Fan Switch Button 7. /FX Button 8.Menu Button 9.Power Switch Button 10.SET Adjustment Knob 11.DC OUTPUT Port 12.DMX IN XLR Port 13.DMX OUT XLR Port Remote Control (Separately Sold Accessory) 1.Light Body Screen Print 2.Bowens Mount 3.LED Bead 4.Metal U-bracket 5.Mount Fixing Pusher 6.DC INPUT Port 7.Handle Direction Adjustment Button 8.Locking handle 9.Sleeve Knob Controller SET 1.Power Switch Button 2.SET Setting Button 3.Reduction Button 4.CH/GR Button 5.Increase Button 6.RST- Reset Mark(Press Reduction Button and Increase Button simultaneously to reset) 27 28 Whats in the BoxM200Bi/M300Bi Installation and Disassembly Guide 1. Connect the Controller and Light Body Press and hold the spring latch button of the connecting cord, insert the connecting cord into the DC INTPUT Port of the light body, insert the other end of the connecting cord into the DC OUTPUT Port of the controller to complete the connection. Connecting Cord
*1 5m Power Cord
*1 Controller Clamp
*1 Light Body
*1 Connecting Cord Fixed Rope
*1 Lamp Cover
*1 Carry Bag CB49
*1 Controller
*1 Bowens-mount Reflector RFT-19
*1 Instruction Manual
*1 Separately Sold Accessories Better shooting effects and using experience matched with following accessories:
Fresnel Attachment for COB LED lights, RC-A6 Remote Control,Safety Wire Rope and SpotLight Attachment. 2. Mount on the tripod Adjust the light body to a proper angle, rotate the screw of sleeve knob to install the light body on the tripod, then rotate the screw of sleeve knob to x the light body on the tripod. The inclination angle of the light body could be adjusted by loosening the bracket angle adjustment handle and then screwing down the handle afterwards. Note: The tripod belongs to separately sold accessories. Tips: Press the handle direction adjustment button to adjust the handle by 360. 29 30 3. Mount on the light stand Loosen the handle of the controller clamp, then insert the light stand and rotate the handle to tighten.Finally, insert the V port of the controller into the clamp slot. Tip: Press and hold the mount xing pusher can easily remove the controller. 4. Installation and disassembly the lamp cover Installation: Press the Mount Fixing pusher top-down, put the lamp cover on Bowens Mount, and rotate clockwise to tighten it. Disassembly: Press the Mount Fixing pusher top-down, then rotate counter-
clockwise to remove it. Note: Make sure to remove the lamp cover before use to avoid overheating damage. Put on the lamp cover to protect the lamp when not in use. 5. Installation and disassembly the standard reflector Installation: Press the Mount Fixing pusher top-down, put the reflector on Bowens Mount, and rotate clockwise to tighten it. Disassembly: Press the Mount Fixing pusher top-down, then rotate counter-
clockwise to remove it. Power Supply 1. AC Power Supply AC100V-240V Spring Latch Note: Please press the latch button when installing or disassembling the power cord and connecting cord. 2.V-mount battery power supply Connect to DMX Controller The Connection operation diagram of Controller and DMX Controller is as follows:
DMX512 Multi-connected 31 Note: The light can be supplied by 14.8V or 26V V-mount battery. Only the side with yellow battery removal button supports unilateral charging, one with. When it is powered by two batteries and one of which is low, the device still can't work normally even if the other one is full. The corresponding battery icon will blink in low battery mode. It is recommended to check whether both batteries have sufcient power when using two batteries. 32 Display Screen 2.4G Wireless Channel Group Bluetooth DMX Fan 3. CCT Adjustment Short press the SET adjustment knob on the main interface to make the arrow aimed at CCT value, then turn it to adjust CCT from 2800K to 6500K, with the increase or decrease of 100K in normal speed and 500K in fast speed. Overheating Alert CCT Value Battery Level Indication Brightness Value Battery Level Indication 4900K Dimming Curve Lock Function Indication Controller Operation Instruction 1. Turn On/Off Press the controller < > Button for 1 second after connecting to the power supply to turn on or off. 2. Brightness Adjustment Turn the SET adjustment knob on the main interface to adjust brightness from 0% to 100%, with an increment of 1% in each level. Rotate clockwise to increase brightness, and counterclock-
wise to decrease brightness. The brightness will increase or decrease by 1% unit in normal rotation speed; and increase or decrease by 10% unit in rapid rotation speed. 4900K 4900K 4 . Menu Setting Short press < MENU > Menu Button to enter the menu interface, displayed in order with Wireless, Bluetooth, DMX, Fan, Dimmer, Screen Bright, Language, Reset, Version &
Upgrade. Turn and short press the SET adjustment knob on the menu interface to select and enter the corresponding setting options interface. 4.1 Wireless The Wireless interface is displayed in order with Wireless Switch, Channel, Group and ID. Short press & turn the SET adjustment knob to complete the settings of Wireless Switch, Channel, Group and ID. 4.2 Bluetooth The Bluetooth interface is displayed in order with Bluetooth Switch, Reset and MAC Code. Short press & turn the SET adjustment k n o b t o c o m p l e t e t h e s e t t i n g s o f Bluetooth Switch and Bluetooth Reset. WIRELESS BLUETOOTH RESET MAC: 0454 33 34 For more smartphone APP operations, please open the "help" in GodoxLightAPP to gain detailed guidance. Note: the APP can be used directly on the rstly installed device (smartphone or tablet). When changing to other mobile device, the light shall be reset before the normal usage of APP. 4.3 DMX The DMX Setting interface is displayed with Address. Turn the SET adjustment knob to choose address from OFF or 1-512, the light will be in DMX OFF or ON mode respectively. Afterwards, short press the SET adjustment knob to return to the previous menu interface. ADDRESS: OFF DMX Practical Form Address Operation Code Mode n(Mode CCT 0-51 FX Note 52-255 DMX*(100/255) Integer DMX*(100/255) Integer 0-100% Brightness 0-100% Brightness Adjustment Adjustment CCT=28+DMX*
(Total CCT/255) CCT 2800K-6500K DMX*(Total FX/255) 1For example Total FX 8DMX=160, FX No.=160*8/255=5 0-85FX Level 86-171FX Level 172-255FX Level n+1 n+2 n+3 n+4 n+5 4.4 Fan Turn the SET adjustment knob on the Fan interface to choose from AUTO, OFF, LOW, HIGH modes. Note: Enter mute mode when turning off the fan.Short press the fan switch button to turn on or turn off the fan. LOW 4.5 Dimmer Turn the SET adjustment knob on the D i m m e r i n t e r f a c e t o c h o o s e linear/S-curve/exponential/
logarithmic dimming curve. Dimmer 4.6 Screen Bright Turn the SET adjustment knob on the Screen Bright interface to choose 1, 2, 3 levels of screen brightness. 4.7 Language Turn the SET adjustment knob on the Language interface to choose English or Simplied Chinese. ENGLISH 35 36 4.8 Reset Turn the SET adjustment knob on the Reset interface to choose Yes or No and shor t press to conrm. If you choose Yes , the system will initiate r e s e t t i n g p r o g r a m a n d r e s e t t i n g progress bar is displayed on the screen, after which it will return to the main interface. YES NO 1 Dim 20 1 Dim 20 4.9 Version & Upgrade The Version Code displayed on the Version & Upgrade interface is the rmware version of the product. Version&Upgrade V 0.03 Power off and insert USB disk with new firmware Restart to upgrade 5. Light Effect Setting FX/
Short press < > button to enter FX Light Effect interface, turn the SET adjustment knob to choose among 21 effects: flash, lightning, broken bulb, TV , candle, re, rework, etc, short press again to exit FX mode. Note: Short press the SET adjustment knob to change the rate and adjust brightness after choosing one of the above Light Effects. 1 Dim 20 1 Dim 20 Flash Mode Lightning Mode Broken Bulb Mode TV Mode 1 Dim 20 1 Dim 20 Candle Mode Fire Mode 1 Dim 20 Firework Mode Tip: Long press the < > Button for 3 seconds to lock/unlock the panel. FX/
Connecting Cord Issue When the connecting cord is not correctly connected to the light or controller, a sepa-
rated icon of connecting cord and device is displayed on the panel. Please check the connecting ports of the controller and light. 37 38 Switch from AC Power Supply to V-Mount Battery Power Supply Unplug the power cord and install V-mount battery then turn on the product. NoteIf you install the V-mount battery before unplugging the power cord and the brightness value is set higher than the maximum brightness that the battery can be turned onthen you switch to V-mount battery power supply by unplugging the power cord, the light and the controller will auto-
matically power off. The machine can only resume mormal operation after reboot. 39 Maximum Brightness of M200Bi in Different States CCT mode: Maximum Brightness (%) in Auto Cooling Mode or High-Speed Cooling Mode when supplied by V-mount battery V-mount battery linear S-curve exponential logarithmic 14.8V(single) 14.8V(double) 26V(single) 14.8V+26V 26V(double) 40%
80%
80%
100%
100%
42%
55%
55%
100%
100%
70%
90%
90%
100%
100%
10%
30%
30%
100%
100%
CCT mode: Maximum Brightness (%) in Fan Off Mode when supplied by V-mount battery V-mount battery linear S-curve exponential logarithmic 14.8V(single) 14.8V(double) 26V(single) 14.8V+26V 26V(double) 20 20 20 20 20 35 35 35 35 35 55 55 55 55 55 6 6 6 6 6 CCT mode: Maximum Brightness (%) in Low-Speed Cooling Mode when supplied by V-mount battery V-mount battery linear S-curve exponential logarithmic 14.8V(single) 14.8V(double) 26V(single) 14.8V+26V 26V(double) 40%
60%
60%
60%
60%
42%
48%
48%
48%
48%
40 70%
80%
80%
80%
80%
10%
18%
18%
18%
18%
CCT mode: Maximum Brightness (%) in different Fan Mode when supplied by AC power Fan Mode linear S-curve exponential logarithmic Auto Cooling 100%
100%
100%
Off Low-Speed Cooling 20%
60%
35%
48%
55%
80%
High-Speed Cooling 100%
100%
100%
100%
6%
18%
100%
FX mode: Maximum Brightness (%) in different Fan Mode when supplied by AC power Auto Cooling Off Low-Speed Cooling 100%
20%
60%
High-Speed Cooling 100%
FX mode: Maximum Brightness (%) in different Fan Mode when supplied by V-mount battery V-mount battery Auto Cooling Off Low-Speed Cooling High-Speed Cooling 14.8V(single) 14.8V(double) 26V(single) 14.8V+26V 26V(double) 40%
80%
80%
100%
100%
20%
20%
20%
20%
20%
40%
60%
60%
60%
60%
40%
80%
80%
100%
100%
41 Maximum Brightness of M300Bi in Different States CCT mode: Maximum Brightness (%) in Auto Cooling Mode or High-Speed Cooling Mode when supplied by V-mount battery V-mount battery linear S-curve exponential logarithmic 14.8V(single) 14.8V(double) 26V(single) 14.8V+26V 30%
60%
60%
90%
40%
48%
48%
65%
65%
80%
80%
95%
8%
20%
20%
50%
26V(double) 100%
100%
100%
100%
CCT mode: Maximum Brightness (%) in Fan Off Mode when supplied by V-mount battery V-mount battery linear S-curve exponential logarithmic 14.8V(single) 14.8V(double) 26V(single) 14.8V+26V 26V(double) 25 25 25 25 25 38 38 38 38 38 60 60 60 60 60 7 7 7 7 7 CCT mode: Maximum Brightness (%) in Low-Speed Cooling Mode when supplied by V-mount battery V-mount battery linear S-curve exponential logarithmic 14.8V(single) 14.8V(double) 26V(single) 14.8V+26V 26V(double) 30%
60%
60%
60%
60%
40%
48%
48%
48%
48%
42 65%
80%
80%
80%
80%
8%
20%
20%
20%
20%
CCT mode: Maximum Brightness (%) in different Fan Mode when supplied by AC power Software Upgrade Fan Mode linear S-curve exponential logarithmic Auto Cooling 100%
100%
100%
Off Low-Speed Cooling 25%
60%
38%
48%
60%
80%
High-Speed Cooling 100%
100%
100%
100%
7%
20%
100%
FX mode: Maximum Brightness (%) in different Fan Mode when supplied by AC power Auto Cooling Off Low-Speed Cooling 100%
25%
60%
High-Speed Cooling 100%
FX mode: Maximum Brightness (%) in different Fan Mode when supplied by V-mount battery V-mount battery Auto Cooling Off Low-Speed Cooling High-Speed Cooling 14.8V(single) 14.8V(double) 26V(single) 14.8V+26V 30%
60%
60%
90%
26V(double) 100%
25%
25%
25%
25%
25%
30%
60%
60%
60%
60%
30%
60%
60%
90%
100%
Note: The dimming curve is not adjustable in FX mode, it is linear in default.The above data is based on 26V 270Wh 10.5Ah battery and 14.8V 150Wh 10.2Ah battery. 1.Download the new rmware to the U disk from the ofcial website
(http://www.godox.com.cn/Downloads.html). 2. Turn off the LED light. Insert the U disk with new rmware into the USB upgrade port. 3. Turn on the LED Light, and it will automatically enter the upgrading interface.. 4.It will return to main interface after completion. Notes:
1. New rmware must be downloaded from the ofcial website, and keep only one BIN le in the root directory of the USB disk. 2. The USB port can only support rmware upgrade function. Over-Temperature Protection If the temperature of the light body is too high, the Over-Temperature Protection icon flashes on the main interface, the light body can be used normally. If the temperature of the light body exceeds the limit of Over-Temperature Protection, the Over-Temperature Protection icon flashes on the main interface and the screen works properly after the light goes out in 3 seconds. When the temperature decreases to 50C, the Over-Temperature Protection icon disappears, then the light body can resume working. Fan Troubleshooting If icon appeared and blinking and fan off icon is also appeared on the display, It might be the fan failure. Please contact with customer service. 43 44 CCT 2800K 3200K 4300K 5600K 6500K Testing Conditions M300Bi Illuminance Unit bare lamp with reflector bare lamp with reflector bare lamp with reflector bare lamp with reflector bare lamp with reflector lux fc lux fc lux fc lux fc lux fc lux fc lux fc lux fc lux fc lux fc 1m 4000 370 53000 4900 4800 450 64000 6000 6200 570 83000 7700 6300 580 86000 8000 5500 510 76000 7000 2m 1000 97.9 11200 1000 1300 120 14000 1300 1600 150 17000 1600 1700 160 18000 1700 1500 140 16000 1500 All the above tests are based on the condition of 100 3m 530 49.6 4300 400 640 59.7 5200 480 830 76.8 6700 620 840 78.4 6900 640 740 70 6100 560 brightness. Maintenance This product, except consumables e.g. adapter and power cable, is supported with a one-year warranty. Maintenance of the light must be performed by our authorized maintenance department which can provide original accessories. Unauthorized service will void the warranty. If the product breaks down or gets wet, please do not use it until repaired by professionals. If there is anything abnormal during LED lights working, please turn it off immediately and identify the reasons. Illuminance Testing Data CCT 2800K 3200K 4300K 5600K 6500K Testing Conditions M200Bi Illuminance Unit bare lamp with reflector bare lamp with reflector bare lamp with reflector bare lamp with reflector bare lamp with reflector lux fc lux fc lux fc lux fc lux fc lux fc lux fc lux fc lux fc lux fc 1m 4000 370 53000 4900 4800 450 64000 6000 6200 570 83000 7700 6300 580 86000 8000 5500 510 76000 7000 2m 1000 97.9 11200 1000 1300 120 14000 1300 1600 150 17000 1600 1700 160 18000 1700 1500 140 16000 1500 All the above tests are based on the condition of 100 3m 530 49.6 4300 400 640 59.7 5200 480 830 76.8 6700 620 840 78.4 6900 640 740 70 6100 560 brightness. 45 46 Technical Data Mode Power Light Head Input M200Bi M300Bi 230W (Max) 330W(Max) 48V 4.6A 48V 7A Controller AC Power Input 100-240V~50/60Hz Controller Power Input DC48V V-mount battery (optional) Specications 14.8V, 150Wh / 26V, 270Wh Channel Group ID Color Temperature CRI TLCI 32(1~32) 16(0~9, A~F) 1~99, OFF 2800-6500K 96 97 Working Environment Temperature
-10~40C FX Light Effect Controlling Method Dimming Curve Mute Mode 2.4G Wireless Control Distance Bluetooth Transmission Distance Display Screen Light Body Dimension Controller Dimension Light Body net Controller net 21 kinds within 7 types Support DMX512 , 2.4G Wireless Control, Bluetooth APP 4 types: linear/S-curve/
exponential/logarithmic YES 60m 30m 2.4 inches 425.3*232.3*141.7mm 270.4*123.6*132mm 3.2kg 2.7kg 3.5kg 2.7kg Bluetooth Transmission Frequency 2402.00-2480.00MHz Maximum Transmit Power 5dbm
* Product design and specications are subject to change without notice. Maintenance This product, except consumables e.g. cable, is supported with a one-year warranty. Avoid sudden impacts and the product should be dedusted regularly. Maintenance of the flash must be performed by our authorized maintenance department which can provide original accessories. Unauthorized service will void the warranty. If the product had failures or was wetted, do not use it until it is repaired by professionals. Changes made to the specications or designs may not be reflected in this manual. FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the follow-
ing two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interfer-
ence to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. Declaration of Conformity GODOX Photo Equipment Co,Ltd. hereby declares that the This equipment are in compliance with the essential requirements and other relevant provisions of EU Direc-
tive 2014/53/EU. They are allowed to be used in all EU member states. For more information of DoC, Please click this web link:
http://www.godox.com/DOC/Godox_M200BI_M300BI_DOC.pdf 47 48
() 12 3 12 0755-29609320-8062 GODOX Photo Equipment Co,Ltd. hereby declares that the This equipment are in compliance with the essential requirements and other relevant provisions of EU Direc-
Declaration of Conformity tive 2014/53/EU. They are allowed to be used in all EU member states. For more information of DoC, Please click this web link:
http://www.godox.com/DOC/Godox_M200BI_M300BI_DOC.pdf Warranty Dear customers, as this warranty card is an important certicate to apply for our How to Get the Maintenance Service If maintenance service is needed, you can directly contact the product distributor or maintenance service, please ll in the following form in coordination with the seller and authorized service institutions. You can also contact the Godox after-sale service call safe-keep it. Thank you!
Product Model Product Code Number Information Customer Information Name Contact Number Address Seller Name Information Contact Number Address Date of Sale Note:
Note: This form shall be sealed by the seller. Applicable Products The document applies to the products listed on the Product Maintenance lnformation
(see below for further information). Other products or accessories (e.g. promotional items, giveaways and additional accessories attached, etc.) are not included in this warranty scope. Warranty Period The warranty period of products and accessories is implemented according to the relevant Product Maintenance lnformation. The warranty period is calculated from the day(purchase date) when the product is bought for the rst time, And the purchase date is considered as the date registered on the warranty card when buying the product. and we will offer you service. When applying for maintenance service, you should provide valid warranty card. If you cannot provide valid warranty card, we may offer you maintenance service once conrmed that the product or accessory is involved in the maintenance scope, but that shall not be considered as our obligation. Inapplicable Cases The guarantee and service offered by this document are not applicable in the following cases: . The product or accessory has expired its warranty period; . Breakage or damage caused by inappropriate usage, maintenance or preservation, such as improper packing, improper usage, improper plugging in/out external equipment, falling off or squeezing by external force, contacting or exposing to the improper temperature, solvent, acid, base, flooding and damp environments, etc; . Breakage or damage caused by non-authorized institution or staff in the process of installation, maintenance, alternation, addition and detachment; . The original identifying information of product or accessory is modied, alternated, or removed; . No valid warranty card; . Breakage or damage caused by using illegally authorized, nonstan-
dard or non-public released software; . Breakage or damage caused by force majeure or accident; . Breakage or damage that could not be attributed to the product itself. Once met these situations above, you should seek solutions from the related responsible parties and Godox assumes no responsibility. The damage caused by parts, accessories and software that beyond the warranty period or scope is not included in our maintenance scope. The normal discoloration, abrasion and consump-
tion are not the breakage within the maintenance scope.