English Table Call System User Manual Contents Introduction ................................................................................1 Device & Specification ..........................................................2 Transmitter: Service Call TB-A06 ................................2 Receiver: RE-300 .............................................................4 Operation & Setting .................................................................6 Manual Programming ...............................................................7 Trouble Shooting .......................................................................9 Warning .......................................................................................10 Introduction Introduction TABLE CALL is an easy, smart wireless service bell with 800 meter coverage in diameter. Users can manually program the table call system without using the PC. It helps restaurants to expedite their table turnover and service efficiency. The system capacity is up to 200 pcs table call TB-A06 with 4 pcs receiver RE-300 that you may install from a small restaurant to bigger ones, which is very flexible. The high light of this system are:
Monitor call function to assure high reliability Wide coverage Chargeable, long life span Manual programmable TABLE Call is strongly recommended as simple solutions at below occasions:
Restaurant Coffee Shop Bars and cuisine 1 Device & Specification Transmitter TB-A06 (The service bell) LED indicator Under Charging: Red LED Battery low: Red LED on blinking when push the button, under charging or in battery low Chargeable, 10 pcs max. at one stack The button:
Service call Blue LED light on Cancel the call Push again and Blue light off 2 Device & Specification Transmitter TB-A06 (The service bell) This is a table call with one service button. With its eye-catching LED it obtains waiter s attention at visual once it is pushed, meanwhile, sending alert page to the receiver in order to get service in shortest time. It comes with Monitor call function to keep receiver aware of its availability. Capacity:
Up to 200 pcs in same group 3 Device & Specification Receiver RE-300 (The desk receiver) Power System NO. RX LED:
Blinking in Green when getting a call 50 keys Blue: A service on waiting Red: Reminder (af ter waiting time 1~3 minutes, programmable) Table call dis-link: Blue/Red intercross blinking 4 Device & Specification Receiver RE-300 (The desk receiver) This is a 50-key receiver that users can lay it on reception desk or mounted on the wall. It notifies the staff of which table is in need of service. Capacity:
Up to 4 pcs in same group Key Spec:
50 Key, each one represents to one table, manual programmable Dual LED indicator LED indicator for remind Wall mounted available 5 Device & Specification RE-300 Specifications Frequency RX Baud Rate(bps) Channel spacing Paging Sensitivity(dBm) Selectivity (25KHz) Spurious & Image Rejection Frequency Stability Receiver Type Frequency Deviation Alert Tone SPL Operation Temperature Storage Temperature Power Supply Dimensions (mm) 430 ~ 470MHz 1200 12.5KHz / 25KHz
-122dBm @1200
>=50dB
>=50dBm
<= +/- 3ppm Synthesized 2.5KHz / 4.5KHz
>= 80dB@ 10cm
-10~+60 C
-10 to +60C DC 9V / 2.2A 232 (L) x 170 (W) x 50 (H) 6 Device & Specification TBA06 Specifications Frequency TX TX output High power Transmission radius Channel spacing Maximum Deviation Baud Rate(bps) Conducted Spurious Emission Frequency Stability Operating power Standby Transmit Operation Temperature Storage Temperature Ni-MH Rechargeable battery Low Battery Alert level Dimensions (mm) Charger 430 ~ 470MHz 10mW 400mm 12.5KHz / 25KHz 2.5KHz / 4.5KHz 1200 less - 55dBc
< 1ppm 3.6~4.5V Battery package
(3 pcs Ni-MH Rechageable battery 1.2V)
< 0.3mA 50 ~ 57mA
-10 to +60 C
-10 to +60C 3.6V 350 mAh
< 3.65V 110(Diameter)X 16.2(H) 7 Operation & Setting 5 function keys for simple manual setting:
Number Power on
+
1 2 3 4 5 Setting Frequency Beep on /
off Waiting Time Erase or Add a TB-
A06 TB-A06 in total How to do During setting, if you heard sharp beep it means setting is void. Please reset RE-300 again if so. Always press 50 as confirmation button Until hearing short beep and let go, you will see number 1-10 blue LED light-on. Key in frequency and press 50 until you hear long beeping b-e-e-p to save it. (Ex: 450.550 MHz, please enter 450550. (10=0)) Until you see number 2 turns on. Push again to cancel the beeping. Blue light turn on= Beep on, Blue light turn off=Beep off (Default value:
Beep on). Until hearing short beep, you will see number 1, 2, 3 is on. Then pressing number 1, 2 or 3 again to set up waiting time. After determining the number, please press 50 until you hear long beeping b-e-e-p to save it. (Default value:
2 Mins.) (1=1 Min, 2=2 Mins, 3=3 Mins) Until hearing short beep and let go. All 50 blue LED light on besides the lost or dis-link ones. To erase them: Press numbers they belong to. To add them back: Follow same way and to press their number. Until hearing short beep and let go, all blue LED light on. Plese select the number key standing out total pieces of TB-A06 you have, then push "50" until hearing long "b-e-e-p". 8 Operation & Setting Number
+
Power on Setting How to do During setting, if you heard sharp beep it means setting is void. Please reset RE-300 again if so. Command 1-4, 6: Always press 50 as confirmation button 1. Until you hear short beep and let go, you 1+21 Program pagers 2. 3. will see that all blue lights turn on. Place SAP-T programmer on the table call, pressing its number then 50 until you hear long beeping b-e-e-p. (During programming: the light of number turns out to red) Follow the same way until you finish the last number of Table Call TB-A06. 4. Reset the RE-300 and the programming is successful. 9 Manual Programming 1. Press 1 + 21 and turn on power to enter the programming mode. 50 blue LED all turn on shortly. 2. Insert the programmer kit SAP-T on first TB-A06 for programming. Press the number representing the first table call, then press 50 until you hear long beeping. For example:
Press NO# 1, followed by 50 until you hear the long beeping. You will see the LED indicator turn out to RED which means the number is under programmed. Once successful, the RED LED would turn off and please go to next programming. If failed, please retry. Follow up the step until the last number of TB-A06. 10 Trouble Shooting Due to wireless device, the interference might happen. Each call are guaranteed to receive within 15 to 45 seconds 1. If the button without receiving the message, please manually dismiss the lights on the RE-300 and clear the light on TB-A06 11 Warning RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. 12 Make sure to read this manual before using the machine. Please keep it in hand for future reference. 765-00009-0