FCC ID: QW9JG2022N24GR Drone Mach 10inch With Camera Streaming

VIDEO STREAMING DRONE VIDEO STREAMING DRONE VIDEO STREAMING DRONE CONTENTS VIDEO STREAMING DRONE VIDEO STREAMING DRONE VIDEO STREAMING DRONE INTRODUCTION SPECIFICATIONS READ ALL WARNINGS AND PRECAUTIONS BEFORE USE. v.06 14+

GETTING TO KNOW YOUR DRONE PLEASE READ ALL WARNINGS AND INSTRUCTIONS PRIOR TO USE. KEEP THIS DOCUMENT AS IT CONTAINS IMPORTANT INFORMATION ABOUT YOUR DRONE. Drone must be charged before each use (USB Charge Cable included) Indicator light will turn off once fully charged Install batteries in remote 1. CHARGING 2. PAIRING Before each flight pair the remote with the drone:

1. Turn your drone on and place on a flat, level surface 2. Turn on the remote on and move the left joystick up, then down 3. The beep will indicate successful pairing 4. Repeat steps 1 and 2 if necessary 3. DIRECTIONAL LIGHTS White lights indicate the front of the drone Red lights indicate the back of the drone Not applicable in auto-orientation mode 4. REMOTE CONTROL OVERVIEW Practice flying your drone below 10 feet and at low speeds until comfortable with all controls to avoid damage or injury To cut power to drone, move left joystick to down position Left joystick:

Right joystick: controls flight direction Direction Trim: use to eliminate drift Up/Down controls elevation Left/Right controls spin QUESTIONS OR CONCERNS?

PLEASE GIVE US A CALL ... WERE HERE TO HELP CUSTOMER SERVICE

(800) 374-2744 Before calling please locate the 10-digit code printed on the back of your remote CHOKING HAZARD SMALL PARTS NOT FOR CHILDREN UNDER 3 YEARS. ADULT ASSEMBLY REQUIRED. Video Drone AUTO ORIENTATION LAND SPRINT TRIM ON OFF DIRECTION TRIM Drone Controller Smart Phone Mount Charge Cable with 55cm (21.6inch) length Replacement Propellors REMOTE BATTERY INFORMATION 1. Slide open battery compartment 2. Install 6 AA batteries as shown in diagram shown above 3. Replace and close battery compartment LITHIUM-POLYMER BATTERY WARNING There is a risk of fire and personal injury if Li-Po battery is punctured, damaged or misused Never expose battery to extreme temperatures or moisture Do not subject battery to strong impacts Always keep battery away from flammable materials Only use manufacturer specified batter(ies), charger(s), and/or adapters, if applicable, specified by the manufacturer Battery is not serviceable Let battery cool to room temperature before charging While charging, never leave battery unattended Recycle or dispose of battery according to federal, state and local laws KEEP THIS INSTRUCTION MANUAL FOR REFERENCE BATTERY WARNING Do not mix old and new batteries Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries Insert batteries using the correct polarity. Do not short-circuit the supply terminal Only use manufacturer specied batter(ies), charger(s), and/or adapters, if applicable, specied by the manufacturer Always use, replace, and recharge (if applicable) batteries under adult supervision KEEP THE PACKAGE FOR REFERENCE AS IT CONTAINS IMPORTANT INFORMATION Page 2 Insert antena through hole at the base of the Smart Phone Mount. Align hole on Mount with hole in antena. Insert screw to secure Mount to remote. Carefully slide phone into Mount by pulling up on top of Mount. Adjust angle accordingly. OPERATING DRONE Step 1 Pre Flight Checklist 1. Read all warnings and instructions. 2. Install remote batteries, page 2. 3. Make sure that drone and remote are powered off. 4. Install drone holder. 5. Charge batteries, page 3. Step 2 Choosing a location Drone is designed to be flown indoors and Always make sure you have enough space to fly outdoors. drone. Always follow warnings, page 1. Step 3 Starting Drone 1. Making sure your remote is off, slide drone switch to ON. Drone lights will begin to flicker. 2. Place drone on a flat even surface with clearance according to diagram (Fig 1). 3. Turn remote on. Make sure the left stick (throttle) is in a neutral position (stick is centered). 4. Push the stick up and then down. 5. A single tone indicates that the drone is paired. Drone lights will flicker rapidly then turn on permanently once paired. 6. If pairing is unsuccessful, repeat steps 3-4. Step 4 Lift Off Press the TAKE OFF/LAND button on the front of the drone to lift off. Drone will elevate off the ground and level off into a hover. You can compensate for some of the drones drifting by using the Multi Directional Button or by following Step 5. Step 5 Drone Begins to Drift Follow this step if your drone begins to drift while take off or during flight. Drone drifts backwards: Press the forward Direction Trim Button. Button. Drone drifts forwards: Press the Backwards Direction Trim Drone drifts left: Press the Right Direction Trim Button. Drone drifts right: Press the Left Direction Trim Button. Drone spins clockwise (viewing drone from top): Press the Left Spin Trim Button Drone spins counter-clockwise (viewing drone from top):

Press the Right Spin Trim Button Step 6 Operating Drone in Flight The drones range is approximately 250 feet or 120 feet of altitude:

Read and be aware of all warnings found on Page 1. Maintain your desired elevation by using the Throttle. Push the Throttle joystick to right or left to spin the drone. Use the right joystick to move forward backwards, and side to side. Review step 5 if your drone begins to drift. Drone will begin to blink when drone is paired to remote and battery is low. Step 7 Landing Drone There are two ways to land the drone:

1. Slowly and carefully press the left stick (FLIGHT AND ROTATE) down until drone lands. 2. Or press TAKE OFF/LAND button to trigger auto landing. If the drone begins to drift, you can still control the drones direction using the Navigation stick (right stick). Fig. 1 10 FEET 5 FEET T E E 0 F 1 Always turn off remote prior to retrieving or picking up drone. This will help you avoid accidently activating propellers. Congratulations on your purchase of the Streaming 2.4 GHz Video Drone. Get ready to soar to new heights. Master the art of drone flying with remote control maneuverability. This lightweight drone will provide hours of fun. Drone Battery: 650 mAh Li-po Remote Controller Battery: 6 x 1.5V AA Charging Time: Approximately 100 minutes Maximum Recommended Altitude 120 ft. TABLE OF CONTENTS General Warnings Contents and Remote Battery Installation Charging Battery and Replacing Propellers Remote Overview Operating Drone Modes Tips and FCC Warning Page 1 Page 2 Page 3 Page 4 Page 5 Page 6 Page 7 SAFETY WARNINGS:

Prevent contact with spinning blades by turning off remote prior to handling drone. Not recommended for children under 14 years of age. As with all electrical products, precaution should be observed during handling and use to reduce the risk of electrical shock. Adult supervision is required at all times. Before each use, an adult should review the product and battery to determine that no damage or hazards exist. DO NOT TOUCH SPINNING PROPELLERS. Do not allow anything to intentionally make contact in any way with spinning propellers. Use caution and pay attention to your surroundings while operating drone. Do not fly drone into animals, people, or inanimate objects. Keep drone away from power lines, buildings, trees, public areas, and any other potentially hazardous areas. Do not operate in rain, heavy wind, and or any type of severe weather. Do not land drone on wet surfaces. Never touch or allow others to touch drone while it is flying. Always turn drone off when it is not in use. Always fly drone in large open areas. Never fly drones above or near people, sudden changes in wind or other conditions could lead to unexpected crashes. Always use caution when flying drone vehicles, obey relevant laws, respect the privacy and property rights of others. The drone shall never be modified or used for anything except its intended purpose. Note: Wind above a surface is higher than at ground level. PLEASE RECYCLE OR DISPOSE OF ELECTRONICS PROPERLY RECYCLING INFORMATION IS AVAILABLE AT WWW.MERCHSOURCE.COM Invasion of Privacy Warning Always be mindful of others privacy and do not record video or take images of others without their consent. Check and comply with your federal, state and local laws regarding privacy. Page i Page 1 Connect the Charging Cable to the Drone Insert the Charging Cable into a power source CHARGING BATTERY Note: The Battery Charge Cable will light up when it is charging the battery and turn off when the battery is fully charged. Charge time is approximately 100 minutes. Turn off the drone before charging. Connect the Battery Charge Cable to the charging port on the Drone. Connect connector to power source. Replacing Propellers 1. Follow diagram 2. Remove screw from top of Propeller 3. Remove broken Propeller and replace with new Propeller 4. Make sure you installed the correct blade. Each blade has a number written on it. Match the blades with the corresponding number on the drone 5. Insert screw into top of Propeller DRONE APP Go to your app store on your smart phone and download the 360 Mach Flight application. Live Streaming Options Live Streaming Options VR Viewer VR Viewer Flip Camera View Flip Camera View Take Photos Take Photos Record Video Record Video View Album View Album Pairing Drone - First Time 1. Press the connect to Wi-Fi button 2. Follow the on screen instructions After Connecting Drone 1. Press the Stream Button to begin streaming 2. Press the Album Button to review pictures and videos Page 3 Page 4 NOTE: Hold the STOP button down until the drone lands completely on the ground for an emergency stop Throttle Joystick Spins drone Increases or decreases drone elevation Emergency Stop Forward/ Backwards Adjustment: Slide up to adjust forward and slide down to adjust backwards Light indicates remote is on AUTO ORIENTATION TAKE OFF/LAND SPRINT TRIM ON OFF DIRECTION TRIM Controls flight direction Side to Side Adjustment:

Slide left to adjust to the left and slide right to adjust to the right Auto orientation Auto Take-off & hover and Auto Land Spin trim ON/OFF remote switch VIDEO STREAMING DRONE CUSTOMER SERVICE

(800) 374-2744 TIPS Do not crash drone into sand or dirt. Drone gears may become clogged When first learning to fly, practice lifting off and hovering Stay several feet from walls and buildings Always press throttle all the way down after crashing or when something gets stuck in propellers Never fly drones above or near people, sudden changes in wind or other conditions could lead to unexpected crashes. Always use caution when flying drone vehicles, obey relevant laws, respect the privacy and property rights of others. The drone shall never be modified or used for anything except its intended purpose. WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. TROUBLESHOOTING:

When remote switch is turned on, the remote light does not illuminate:

1) Check that batteries in the remote are installed correctly OR 2) Replace with new batteries During drone flight, the remote LED is flashing:

1) Remote batteries are low; replace them with new batteries

(Fig. 1) AUTO ORIENTATION LAND SPRINT TRIM 60 100 ON OFF DIRECTION TRIM Drone and remote properly pair, but the drone will not lift-off:

1) Drone battery needs charging. Use the USB Charge Cable to connect the drone to power source. After trimming the drone, the drone flight is very unstable and cannot fly properly:

1) One or more blades are most likely damaged;

2) Turn off the drone and remote. 3) Replace with the proper number replacement blade and try flying again. After impact, the drone is unstable:

1) Put the left remote control lever to the left bottom and put the right remote control lever to the right bottom at the same time. This will reset the gyroscope (Fig. 1). 2) If the above does not resolve the issue, reboot the drone and controller and pair again. Remote Controller and Drone can not be paired:

1) Check Point: Remote Controller must be closed to Drone, not exceed 12 feet. Note: If there are 2 sets of Drones within 12 feet for Pairing, you must pair one successfully before pairing the second set. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna,

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. FCC RF Radiation Exposure Statement Caution: To maintain compliance with the FCCs RF exposure guidelines, place the drone at least 20cm from nearby persons. Sharper Image name and logo are registered trademarks. Distributed by and 2017 MerchSource, LLC. Irvine, CA 92618. All rights reserved. The artwork and design of this package are protected by US copyright law and may not be reproduced, distributed, displaced, published or used for any purpose without prior written permission. Altering, removing or reproducing any of the trademark or copyright notices on this package is not permitted. VIDEO STREAMING DRONE VIDEO STREAMING DRONE INSTALLING PHONE HOLDER MODES Auto Orientation Button Auto Orientation default setting is off. To enter this mode press Auto Orientation button. Remote will beep twice. After drone is successfully paired, the 2 white LED lights toward orientation will be the original forward orientation, when drone is in auto orientation mode, the drone will orient to the user (remote), no matter what direction the drone is facing. Pushing the right stick up will send the drone away from the user, pushing it to the right will move the drone right, etc. Remote will beep every 6 seconds to indicate the drone is in Auto Orientation mode. To exit mode, press the Auto Orientation button. Remote will sound 1 long beep indicating that it has exited Auto Orientation mode. Note: Auto Orientation mode is oriented to the user when pairing. If the remote is moved after pairing Auto Orientation, please follow directions above to reset Auto Orientation. Camera taking pictures and creating videos Taking a picture- press camera icon on app once to take a picture. Creating video- press video icon on app once to take a video. Press the video icon on app again to stop recording. PRACTICE INDOORS BEFORE 1ST OUTDOOR FLIGHT. MAKE SURE TO RESET DRONE AFTER HARD LANDING. T E E 0 F 1 10 FEET Page 5 Page 6 China Patent No. ZL201730677298.4 US Patent No. D846,445 Printed in China Page 7

FCC ID: QW9JG2022N24GR size: 2mm(h)*25mm(w) 33568A21120 size: 2mm(h)*11mm(w) Model No: 1012254) size: 2mm(h)*15mm(w)

APPENDIX E Gold Light Toys Factory Attention: Certification reviewer RE: Request for Confidentiality FCC ID: QW9JG2022N24GR To Whom It May Concern:

Permanent Confidentiality Request to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential:

Schematics

| Block Diagrams

| Operational Description Rationale for request for confidentiality:

We have invested considerable time and materials in research and development to produce the referenced product.

) Permanent confidentiality: Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us. if you have questions or need further information, please contact the undersigned. Sincerely, Zin ten. Chon Zhi Kun Chen Senior Magager 2022-3-8 are

APPENDIX B 2022-3-8 Gold Light Toys Factory Federal Communications Commission 445 12% Street SW Washington, DC 20554 Subject: Limited Agency Agreement Gold Light Toys Factory FCC ID: QW9JG2022N24GR To Whom It May Concern:

We, Shantou Chenghai Guangyi Gold Light Toys Factory, hereby authorized Intertek Testing Services to act as our Agent for the purpose of preparing application for FCC ID number QW4JG2022N24GR under all applicable parts of the FCC rules and regulations. The effective date of this limited agency agreement is 2022-3-8. The Limited Agency Agreement expires on 2023-3-8, unless sooner terminated or extended by written notice to Intertek Testing Services and the Federal Communications Commission. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. The applicant is not subject to a denial of federal benefits pursuant to Section S301 of the Anti-Drug Act of 1988, 21 US.C. 862, and no party to the application is subject to a denial of federal benefits pursuant to that section. IF you have any questions or comments, please do not hesitate to contact me. Sincerely, ahi kun Chen Zhi Kun Chen Senior Manager