User Manual BST30 Bluetooth Keypad and Compact Amplifier System English KEF Bluetooth Keypad and Compact Amplifier System Thank you for purchasing KEF Bluetooth keypad and compact amplifier system (BTS30). We are confident that your BTS30 will provide reliable, high performance sound for many years to come. Please read this manual fully before you attempt any connection to the BTS30. In the box 2 BTS30 BTS30 A 1 2 3 4 5 6 7 8 C B D Keypad A. Source LED indicators TV, Bluetooth B. Control Keys TV, Bluetooth, Vol -/+
C. RJ-45 connector Keypad unit output D. Bluetooth ID update port Amplifier 1. Input connectors Analog, Coaxial, Optical 2. Volume limit knob 3. Line output connector 4. Amplifier status LED indicator 5. AC Main power input 6. Loudspeaker output connector 7. Output mode selector Stereo, Mono 8. RJ-45 connector Keypad unit input 4 Wiring analog input/output connector Balanced Unbalanced Wiring loudspeaker output connector RJ-45 connection (T-568B) between Keypad unit and Amplifier, Max. 20 meters 5 Get started TV LED status:
TV Green LED ON = TV source ( optical/ coaxial/ line-in) activate TV Green LED OFF = no TV source for 30 second BT LED status:
Bluetooth Blue LED flash = Discoverable mode Bluetooth Blue LED ON = Connected Amplifier unit LED status:
Red = Standby, Blue = ON, Blue&Red = Fault Operation:
Short press Bluetooth button to activate discoverable mode (1 min) When Bluetooth discoverable mode time out, the system will switch to TV source Pause Bluetooth source, Bluetooth source will switch to TV source within 15s, Play Bluetooth source again, TV source will switch to Bluetooth source within 5s When playing Bluetooth source, press TV button to switch to TV source Press Bluetooth button again, auto connect to Bluetooth device TV input priority:
Optical ->Coaxial ->Line-in Mute / Unmute Press TV button to mute TV source, TV LED will turn OFF Press TV/ VOL+/VOL- to unmute Clear BT ID Long press Bluetooth for 3-5 seconds
*Vol+/ Vol- sync with iOS device volume bar 6 Model Inputs Output Bluetooth Range Bluetooth Capacity Bluetooth Frequency Bluetooth Power Operation Voltage Frequency Response EQ Frequency Signal To Noise Speaker Output Short Circuit Protection Dimension Weight BTS30 Bluetooth 4.2 with Qualcomm aptX codec Optical Coaxial Line-in Stereo Mode 2x15W@8 Mono Mode 30W@4 Line-Output 10m 8 Devices 2.4GHz 2.5mW For Class 2 100-240VAC 20Hz-20KHz 100Hz +6dB, 10KHz -1dB 95dB Yes Amplifier Unit: 143mmX125mmX45mm (5.63X4.92X1.77 inch) Control Unit: 45mmX45mmX40mm (1.77X1.77X1.58 inch) Metal Frame: 71mmX71mmX1mm (2.80X2.80X0.04 inch) Amplifier Unit: 530g (1.168 lbs) BT Keypad Unit: 40g(0.088 lbs) Metal Frame: 28g(0.061 lbs) BT Keypad Unit IP64 certified Amplifier unit: UL2043-approved for use in air handling spaces For Further information and troubleshooting, please visit the KEF website: KEF.COM KEF reserves the right, in line with continuing research and development, to amend or change specifications. E&OE. 7 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Note: The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. such modifications could void the user's authority to operate the equipment. RF warning statement:
The device has been evaluated to meet general RF exposure requirement. This equipment complies with FCCs RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna(s) must not be co-located or conjunction with any other antenna or transmitter.