FCC ID: VC961070240 R/C VEHICLE - PAGANI / LAMBORGHINI

VEHICLE TRANSMITTER FRONT WHEEL ALIGNMENT LEVER POWER SWITCH STEERING WHEEL (LEFT/ RIGHT) POWER SWITCH 6 X 1.5V "AA" BATTERIES (NOT INCLUDED) BATTERY REPLACEMENT:

VEHICLE 1. Turn the power switch to the OFF position. 2. Use a Phillips screwdriver to loosen and remove the screw of the battery compartment door as shown. 3. Open the battery compartment door. 4. Remove old batteries and replace with 6 new 1.5V AA batteries. 5. Close the battery compartment door and tighten the screw. TRANSMITTER 1. Turn the power switch to the OFF position. 2. Use a Phillips screwdriver to loosen and remove the screw of the battery compartment door as shown. 3. Open the battery compartment door. 4. Remove old batteries and replace with 2 new 1.5V AA batteries. 5. Close the battery compartment door and tighten the screw. HOW TO OPERATE:

Install antenna to the transmitter. Turn the vehicle switch ON. Push speed control stick forward (upwards) to drive forward. Push speed control stick backwards (downwards) to drive in reverse. Release speed control stick to neutral position to stop the vehicle. Steering to the left, right, or straight direction is controlled by the steering control stick. WHEEL ALIGNMENT:

Adjust the lever under the chassis when the steering is not properly aligned. OFF ON THROTTLE

(FORWARD/ BACKWARD) 2 X 1.5V "AA" BATTERIES

(NOT INCLUDED) BATTERY CAUTION:

1. Rechargeable batteries are not recommended. 2. Alkaline batteries are recommended. 3. Non-rechargeable batteries are not to be recharged. 4. Rechargeable batteries are to be removed from the toy before being charged. 5. Rechargeable batteries are only to be charged under adult supervision. 6. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries. 7. Do not mix old and new batteries. 8. Only batteries of the same or equivalent types as recommended are to be used. 9. Batteries are to be inserted with the correct polarity. 10. The supply terminals are not to be short-circuited. 11. If batteries are loose, bend out the contacts for a tight t. 12. Exhausted batteries must be removed from the toy and be disposed of immediately. Do not put the batteries in a re. 13. Remove batteries from the toy when not in use. 14. Check the product periodically for signs of damage to electrical parts;

do not play with product until damage has been properly assessed. If the unit malfunctions, please remove the batteries for one minute and reinstall again. If the malfunctions persist, please replace with new batteries. Dont forget to remove batteries from the vehicle and transmitter when you have nished operating your vehicle. BATTERIES SHOULD BE INSTALLED BY ADULTS ONLY. The trademarks Pagani, Huayra, Zonda, Utopia and any other trademarks related to Pagani Group are registered trademarks and used pursuant to a license from PAGANI S.P.A., Italy Please keep this packaging for future reference. Colors, designs & contents may vary. All rubber bands, plastic and wire ties, as well as tags, are not part of this toy and should be discarded for your childs safety. Remove wire ties before giving this toy to your child. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. The device must not be co-located or operating in conjunction with any other antenna or transmitter. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. ALKALINE BATTERIES ARE RECOMMENDED. 1.5V AA X 8 Dont put in trash. Recycle or dispose as hazardous waste. Grandex Intl Development Ltd. P.O. Box 871 Port Washington NY 11050 Tel: 516-365-4111 Imported By:

BJ's Wholesale Club, Inc. 350 Campus Drive Marlborough, MA 01752 GDX02010524S SKU 325935 NO. 61070 MADE IN CHINA VEHICLE TRANSMITTER FRONT WHEEL ALIGNMENT LEVER POWER SWITCH STEERING WHEEL (LEFT/ RIGHT) POWER SWITCH 6 X 1.5V "AA" BATTERIES (NOT INCLUDED) BATTERY REPLACEMENT:

VEHICLE 1. Turn the power switch to the OFF position. 2. Use a Phillips screwdriver to loosen and remove the screw of the battery compartment door as shown. 3. Open the battery compartment door. 4. Remove old batteries and replace with 6 new 1.5V AA batteries. 5. Close the battery compartment door and tighten the screw. TRANSMITTER 1. Turn the power switch to the OFF position. 2. Use a Phillips screwdriver to loosen and remove the screw of the battery compartment door as shown. 3. Open the battery compartment door. 4. Remove old batteries and replace with 2 new 1.5V AA batteries. 5. Close the battery compartment door and tighten the screw. HOW TO OPERATE:

Install antenna to the transmitter. Turn the vehicle switch ON. Push speed control stick forward (upwards) to drive forward. Push speed control stick backwards (downwards) to drive in reverse. Release speed control stick to neutral position to stop the vehicle. Steering to the left, right, or straight direction is controlled by the steering control stick. WHEEL ALIGNMENT:

Adjust the lever under the chassis when the steering is not properly aligned. OFF ON THROTTLE

(FORWARD/ BACKWARD) 2 X 1.5V "AA" BATTERIES

(NOT INCLUDED) BATTERY CAUTION:

1. Rechargeable batteries are not recommended. 2. Alkaline batteries are recommended. 3. Non-rechargeable batteries are not to be recharged. 4. Rechargeable batteries are to be removed from the toy before being charged. 5. Rechargeable batteries are only to be charged under adult supervision. 6. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries. 7. Do not mix old and new batteries. 8. Only batteries of the same or equivalent types as recommended are to be used. 9. Batteries are to be inserted with the correct polarity. 10. The supply terminals are not to be short-circuited. 11. If batteries are loose, bend out the contacts for a tight t. 12. Exhausted batteries must be removed from the toy and be disposed of immediately. Do not put the batteries in a re. 13. Remove batteries from the toy when not in use. 14. Check the product periodically for signs of damage to electrical parts;

do not play with product until damage has been properly assessed. If the unit malfunctions, please remove the batteries for one minute and reinstall again. If the malfunctions persist, please replace with new batteries. Dont forget to remove batteries from the vehicle and transmitter when you have nished operating your vehicle. BATTERIES SHOULD BE INSTALLED BY ADULTS ONLY. THE LAMBORGHINI AND LAMBORGHINI BULL AND SHIELD TRADEMARKS, COPYRIGHTS, DESIGNS AND MODELS ARE USED UNDER LICENSE FROM AUTOMOBILI LAMBORGHINI S.P.A, ITALY. OFFICIAL LICENSEE: P&C INTERNATIONAL DEVELOPMENT LIMITED. Please keep this packaging for future reference. Colors, designs & contents may vary. All rubber bands, plastic and wire ties, as well as tags, are not part of this toy and should be discarded for your childs safety. Remove wire ties before giving this toy to your child. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. The device must not be co-located or operating in conjunction with any other antenna or transmitter. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. ALKALINE BATTERIES ARE RECOMMENDED. 1.5V AA X 8 Dont put in trash. Recycle or dispose as hazardous waste. Grandex Intl Development Ltd. P.O. Box 871 Port Washington NY 11050 Tel: 516-365-4111 Imported By:

BJ's Wholesale Club, Inc. 350 Campus Drive Marlborough, MA 01752 GDX02010524S SKU 325935 NO. 61070 MADE IN CHINA

50 mm x 15 mm FCC ID: VC961070240 MADE IN CHINA This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. Fo ID: Vo961070240 MADEIN CHINA This device complies with Part 15 of the FCC Rules Operton is subject to the folowing wo conditions: (1) This device ay not cause harmful interference, and

(2h device must accept any intrerence feed, nung itererence that may cause undested operation.

Grandex International Development Limited Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2024.05.11 Ref: Attestation Statements Part 2.911(d)(7) Filing FCC ID or Grantee Code: VC961070240 Applicant FRN: 0024661597

[Grandex International Development Limited.] (the applicant) certifies that, as of the date of the filing of the application, [FCC US Agent, LLC] is our designated U.S. agent for service of process for the above referenced FCC ID. [Grandex International Development Limited.] accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment.

[FCC US Agent, LLC] accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information:

Name: FCC US Agent, LLC U.S. Agent FRN: 0033402884 Address: 3722 Illinois Avenue, Saint Charles, IL, 60174, USA Contact Person: Tim Payne Tel.: 708-571-3148 Email: [email protected] Sincerely, Grandex International Development Limited. FCC US Agent, LLC Peter Ng Tim Payne

[Insert Applicant signature [U.S. Agent signature]

(https://www.fec.gov/supplychain/coveredlist) Grandex International Development Limited. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2024.05.11 FCC 1D: VC961070240 Ref. #1: Attestation Statements Part 2.911(d)(5)(i) Filing

{Grandex International Development Limited.] (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Ref. #2: Attestation Statements Part 2.911(d)(5)(ii) Filing

[Grandex International Development Limited.] (the applicant) certifies that, as of the date of the filing of the application, the applicant [is not] identified on the Covered List as an entity producing covered equipment. Cover List Link:

Applicant: Grandex International Development Limited. Address: Unit 2401, Million Fortune Ind Ctr., 34-36 Chai Wan Kok Street, Tsuen Wan, Hong Kong Contact Person: Peter Ng Tel.: 852-24052266 Email: [email protected] Sincerely, Rev 2/6/2023

Confidentiality Request Letter One Distribution Center Circle, Suite 1 Littleton, MA 01460 Tel: +1 978 486 8880 Email: [email protected] Website:

Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 (obsolete) 1.0 2.0 August - 11 - 2008 Updated company template & Added text box 2.0 3.0 Jan-31-2012

(obsolete) Added IC confidentiality letter form (obsolete) 3.0 4.0 March-26-2015 Corrections to STC form. Added reference to KDB 4.0 5.0 Nov-19-2015

(obsolete}

Updated company logo (current) 5.0 6.0 Jun-26-2019 Updated References and Contact Info 6.0 7.0 Auq-30-2020 Updated BV Company Address 7.0 8 Nov-28-2023 SCS-F019: Confidentiality Request Letter Grandex Internationa Development Limited 2024.05.11 To:

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046-1609 Ce:

Bureau Veritas Consumer Products Services Inc. One Distribution Center Circle, Suite 1 Littleton, MA 01460 Subject: Confidentiality Request for FCC ID: VC961070240 Pursuant to CFR 47 sections 0.457 and 0.459, we respectfully request permanent confidential treatment of the following Exhibits accompanying this application be held confidential:

Type of Confidentiality Requested Exhibit C1 Short Term C1 Short Term C1 Short Term C1 Short Term C1 Short Term CI Short Term C1 Short Term CI Short Term

& Short Term

>} Permanent CJ Permanent i Permanent CJ Permanent CJ Permanent

&] Permanent

(J Permanent i Block Diagram External Photos Internal Photos Operational Description/ Theory of Operation Parts List Tune-Up Procedure Schematics Test Setup Photos User's Manual The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality:

To avoid premature release of sensitive information prior to marketing or release of the product to the public, the applicant requests the following documents contained in this certification application be temporarily withheld from public disclosure for an initial period of 45 (]

or 180 [J days; or for a specified date of not to exceed 180 days from the Grant Date The applicant understands that disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Client's signature: Peter Ng Client's name & tile: General Contact information / address: Unit 2401, Million Fortune Ind Ctr., 34-36 Chai Wan Kok Street, Tsuen Wan, Hong Kong i Permanent confidentiality may be requested in accordance with FCC KDB 72692 SCS-F019: Confidentiality Request Letter Page 2 of 2