FCC ID: W9V-DX250-GP WIMAX 802.16E INDOOR IAD

by: Green Packet Berhad, Taiwan latest update: 2012-05-15 model: DX250-GP

Two grants have been issued under this FCC ID on 05/15/2012 (this is one of two releases in 2012 for this grantee). Public details available include internal & external photos, manuals, and frequency information. some products also feature user submitted or linked troubleshooting guides, instructions, warrantee terms, password defaults, & drivers.

permalink for this FCC identifier

search for: Repair details

from iFixIt

Replacement

on Amazon

Trade-in? Recycling locations

eg is reader-supported. when you buy through links on our site, we may earn an affiliate commission.

eg for Slack usage

all	frequencies			exhibits	applications
		manuals

all exhibits 13
1 ~ 2012-05-15 13
2 ~ 2012-05-15 13

app s				submitted / available
1 2	USERS MANUAL 1	Users Manual	pdf	2.68 MiB	/ October 11 2012
1 2	USERS MANUAL 2	Users Manual	pdf	2.73 MiB	/ October 11 2012
1 2		Cover Letter(s)	pdf
1 2		External Photos	pdf		/ October 11 2012
1 2		Internal Photos	pdf		/ October 11 2012
1 2		Internal Photos	pdf		/ October 11 2012
1 2		ID Label/Location Info	pdf
1 2		Cover Letter(s)	pdf
1 2		Cover Letter(s)	pdf
1 2		RF Exposure Info	pdf
1 2		Cover Letter(s)	pdf
1 2		Test Report	pdf
1 2		Test Setup Photos	pdf		/ October 11 2012

exhibit
download
text

1 2

USERS MANUAL 1

Users Manual

pdf

2.68 MiB

/ October 11 2012

@ Package Contents pine ia LAN Cable Mini uakeri

@ Device Body 195.2mm WPS LAN Reset LED Indicators Button Ports Button Power Connector VoIP Ports

@ LED Indicators a 2 7 9) 79) Wi-Fi LED Phone LED Signal Strength LED

| @ Set up WiMAX Connection Power On Connect your WiMAX CPE to power with the power cord and plug. Then, the LEDs will blink for a few seconds and go off. Power adapter Wall socket Establish WiMAX Connection Once powered on, the CPE will automatically connect to your subscribed WiMAX service. The operation to setting up connections takes place in the following orders:

179) @)

@ One LED blinks green: it is searching for signal. GM) @)

@ Two LEDs blink green: it is connecting to WiMAX. QM) @)

@ Three LEDs blink green: the connection is completed and ready. G) q) Note: Do not disconnect power during this process. It may take a few minutes to complete modem initialization.

5 Modem Placement

| Adjust the location of the WiMAX CPE for optimized signal reception.

@ One green LED: the signal is weak. Ww & G@)

@ Two green LEDs: the signal is good. Ww G) @)

@ Three green LEDs: the signal is excellent. w @ @) Tip: You can try several spots in the house for an optimal location. Usually, it is recommended to place the indoor modem next to window, facing the base station. Window WiFi enabled WiMax computers 4G Modem

(Closed to Window) iw Network and Connectivity Use the LAN cable to connect the modem and your laptop/PC. Once connected, the Ethernet port LED lights up in green. If the Ethernet port blinks in yellow, it indicates data transmission is in process. Ethernet port Ethernet cable Laptop/PC Click on the Internet Browser Now you are able to connect to the Internet.

| @ Set up Wi-Fi Connection

| If you have Wi-Fi devices in your home, you can connect them to the Internet with your WiMAX modem.

| When the Wi-Fi LED lights up it indicates that Wi-Fi is enabled. When the Wi-Fi LED starts blinking, it indicates that data is being transmitted. EE Switch on Wi-Fi on Your Laptop

a ___ ee *=co PLETE TTT TT Wi-Fi Switch on a Laptop

BD Find the Wireless Network

Right-Click on the Wireless Network Connection icon at the bottom right of the screen and select "View Available Wireless Networks". 5 Enter security password

In the list of available networks, choose the one that matches the SSID Key. Click "Connect". You will be prompted to key in the WEP password.

| *The SSID key and WEP password are printed at the bottom of your modem. 802.16e WiMAX Modem MAC:

UVAQD AAU R BETIE iri ac 20000000000x a4 eter: SSID:XXXXXX

[eteare WEP:XXXXXXXXXX MADE IN CHINA,

A Click on your Internet browser

vs Now you will be able to connect to the Internet. Security Notice

| If you want to change the default SSID or WEP key, open any Internet browser and type in the URL address to access the "Graphic User Interface"

at http://10.1.1.254, click on the "Networking" to start the further setting. Username

exhibit
download
text

1 2

USERS MANUAL 2

Users Manual

pdf

2.73 MiB

/ October 11 2012

@ Set up VoIP Service This feature allows you to make phone calls over the WiMAX connection. Just simply plug the phone handset to the VoIP port on the modem, and it is ready. VoIP Service Subscription Please contact your local service provider for information on VoIP service subscription. Connect your phone Connect one end of the phone Cable (RJ-11) to the Phone Port of the modem and the other end to the phone. a Phone port Phone cord Use VoIP Service Once the telephone set is properly connected to the port, you are ready to make phone calls. 7) ) When the modem and telephone set are connected with the cord, VoIP LED will light up in blue, and you can use the VoIP service now. If you have subscribed to VoIP service, and both the modem and phone set have been properly set, but the LED does not work, you can disconnect the cord and try again with different cord or port. If the problem still exists, please contact the service provider for technical support. LED Light Indication Phone Service registered and ready ON Phone 1 Off-hook / Ringing / Busy Status Blinking | Incoming voicemail waiting OFF Phone Service not registered / disabled Phone Service registered and ready ON Phone 2 Off-hook / Ringing / Busy Status Blinking | Incoming voicemail waiting OFF Phone Service not registered / disabled Claim FCC Regulations to DK-256 FCC Regulations

@ This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

@ This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. RF Exposure Information This device meets the government's requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government.

@ This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation. a) DX-230 / DX-250 / DX-350 Quick Start Guide

] Desktop modem for multiple users

		frequency	equipment class	purpose
1	2012-05-15	2496 ~ 2690	TNB - Licensed Non-Broadcast Station Transmitter	Original Equipment
2		2422 ~ 2452	DTS - Digital Transmission System

Application Forms

app s	Applicant Information
1 2	Effective	2012-05-15
1 2	Applicant's complete, legal business name	Green Packet Berhad, Taiwan
1 2	FCC Registration Number (FRN)	0018658757
1 2	Physical Address	6F, NO.21, LANE 583 RUEIGUANG RD
1 2		Taipei City, N/A 11492
1 2		Taiwan

app s	TCB Information
1 2	TCB Application Email Address	T******@TIMCOENGR.COM
1 2	TCB Scope	B1: Commercial mobile radio services equipment in the following 47 CFR Parts 20, 22 (cellular), 24,25 (below 3 GHz) & 27
1 2	TCB Scope	A4: UNII devices & low power transmitters using spread spectrum techniques

app s	FCC ID
1 2	Grantee Code	W9V
1 2	Equipment Product Code	DX250-GP

app s	Person at the applicant's address to receive grant or for contact
1 2	Name	F****** H******
1 2	Title	VP
1 2	Telephone Number	+886 ******** Extension:
1 2	Fax Number	+886 ********
1 2	E-mail	f******@greenpacket.com

app s	Technical Contact
		n/a

app s	Non Technical Contact
		n/a

app s	Confidentiality (long or short term)
1 2	Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?:	Yes
1 2	Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?:	Yes
1 2	If so, specify the short-term confidentiality release date (MM/DD/YYYY format)	11/10/2012
	if no date is supplied, the release date will be set to 45 calendar days past the date of grant.

app s	Cognitive Radio & Software Defined Radio, Class, etc
1 2	Is this application for software defined/cognitive radio authorization?	No
1 2	Equipment Class	TNB - Licensed Non-Broadcast Station Transmitter
1 2	Equipment Class	DTS - Digital Transmission System
1 2	Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant)	WIMAX 802.16E INDOOR IAD
1 2	Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application?	No
1 2	Modular Equipment Type	Does not apply
1 2	Purpose / Application is for	Original Equipment
1 2	Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization?	Yes
1 2	Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization?	No
1 2	Grant Comments	Power listed is EIRP. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. End-users and installers must be provided with transmitter operating conditions for satisfying RF exposure compliance.
1 2	Grant Comments	Power listed is conducted. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. End-users must be provided with transmitter operating conditions for satisfying RF exposure compliance. This device supports 20 MHz and 40 MHz bandwidth mode.
1 2	Is there an equipment authorization waiver associated with this application?	No
1 2	If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded?	No

app s	Test Firm Name and Contact Information
1 2	Firm Name	Sporton International Inc.
1 2	Name	A** C****
1 2	Telephone Number	886-3******** Extension:
1 2	Fax Number	886-3********
1 2	E-mail	a******@sporton.com.tw

Equipment Specifications
	Line	Rule Parts	Grant Notes	Lower Frequency	Upper Frequency	Power Output	Tolerance	Emission Designator	Microprocessor Number
1	1	27		2496	2690	1.2218	0.0111 ppm	4M46G7D
1	2	27		2496	2690	1.122	0.0122 ppm	9M32G7D
1	3	27		2496	2690	1.2274	0.0114 ppm	4M48W7D
1	4	27		2496	2690	1.1272	0.0128 ppm	9M24W7D
	Line	Rule Parts	Grant Notes	Lower Frequency	Upper Frequency	Power Output	Tolerance	Emission Designator	Microprocessor Number
2	1	15C		2412	2462	0.1683
2	2	15C		2422	2452	0.1675

some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details