FCC ID: VG8MWBWB01 Wi-Fi & BLE Module

WIFI+BT Module MWB1830-WB01 PRODUCTS USERMANUAL Version 1.0 PRODUCTS USERMANUAL MWB1830-WB01 Contents 1. Product Description..........................................................................................................-2-

2. Product Features......................................................................................................................-2-

3. Product Specification...............................................................................................................-2-

4. Pin Definitions.........................................................................................................................-3-

5. PCB Antenna specifications............................................................................................. -3-

6. FCC Statement.........................................................................................................................-4-

7. Canada Statement............................................................................................................. ...-5-

PAGE 1 OF 6 Version 1.0 PRODUCTS USERMANUAL MWB1830-WB01 Product Description Interface Standard 802.11a/b/g/n WIFI+BT Module Modulation Method Data Transfer Rate MWB1830-WB01 WiFiUART BTUART Model Product Name Product Features Product Specification Complies with IEEE 802.11g;

802.11b; 802.11n;standard for 2.4GHz Wireless LAN. ONE Transmit and ONE Receive path(1T1R) Supports Ad-Hoc/Infrastructure modes Works with all existing network frastructure. Capable of up to 128-Bit WEP Encryption. Freedom to roam while staying connected. UP to 75.5Mbps High-Speed Transfer Rate in 802.11N mode of operation. Operating SystemsLinux Low power consumption. The MWB1830-WB01 is a high-gain and low power consumption wifi module . It fully complies with IEEE 802.11b/g/n feature rich wireless connectivity at high standards,delivers reliable,cost-effective,throughput from an extended distance.When 5V, UART and GND were connected,This module is working. The Bluetooth part supports latest 5.1LE operation. 1,2,5.5,6,11,12,18,22,24,30,36,48,54,60,9 0 and maximum of 75.5Mbps QPSK,BPSK ,CCK(802.11b) QPSK,BPSK,16QAM ,64QAM with OFDM

(802.11g) BPSK,QPSK,16QAM ,64QAM with OFDM

(802.11n) GFSK(BT) 2.4GHz: CH 1~CH11 for FCC

< 20dBm Bluetooth v5.1 Low Energy(LE);

revision 1.1 for WLAN Easy to install and configure. Complies with UART base specification Operating Temperature -40 ~ 85C ambient temperature 5 to 95 % maximum (non-condensing)

-40 ~ 125C ambient temperature Up to 150 meters in open space WEP, TKIP, AES, WPA, WPA2 Ad hoc, Infrastructure Storage Temperature Operating Voltage Operation Range Frequency Band Operation Mode Transmit Power OS Support Humidity Security 5V10%

AliOS PAGE 2 OF 6 Version 1.0 PRODUCTS USERMANUAL MWB1830-WB01 Pin Definitions Pin Name GND TX RX Functional Description GND UART-TX,receive end in UART download UART-RX,transmit end in UART download,floating or pull up 5V power supply 5V PCB Antenna specifications Antennas:

2.4G PCB antenna & 2.42 dBi The antenna is permanently attached, cant be replaced. NOTICE:

please keep this product and accessories attached to the places which children can't touch;

do not splash water or other liquid onto this product, otherwise it may cause damage;

do not put this product near the heat source or direct sunlight, otherwise it may cause deformation or malfunction;

please keep this product away from flammable or naked flame;

please do not repair this product by yourself. Only qualified personnel can be repaired. PAGE 3 OF 6 Version 1.0 PRODUCTS USERMANUAL MWB1830-WB01 FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Please notice that if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains FCC ID: VG8MWBWB01 any similar wording that expresses the same meaning may be used. The modular can be installed or integrated in mobile or fix devices only. This modular cannot be installed in any portable device, for example, USB dongle like transmitters is forbidden. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter and must be installed to provide a separation distance of at least 20cm from all persons. A separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and difference antenna configurations. There is requirement that the grantee provide guidance to the host manufacturer for compliance with Part 15B requirements. The end user manual shall include all required regulatory information/warning as shown in this manual, include:

This product must be installed and operated with a minimum distance of 20 cm between the radiator and user body. The module complies with FCC Part 15.247 /RSS-247 and apply for Single module approval. PAGE 4 OF 6 Version 1.0 PRODUCTS USERMANUAL MWB1830-WB01 Canada Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licenceexempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the device. L'metteur/rcepteurexempt de licence contenu dans le prsent appareil est conforme aux CNR d'Innovation. Sciences et DveloppementconomiqueCanada applicables aux appareils radio exempts de licence.. Lexploitation est autorise aux deux conditions suivantes :

(1) lappareil ne doit pas produire de brouillage;

(2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. The device has been tested and compliance with SAR limits,users can obtain Canadian information on RF exposure and compliance. Aprs examen de ce matriel aux conformit aux limites DAS et/ou aux limites dintensit de champ RF,les utilisateurs peuvent sur lexposition aux radiofrquences et la conformit and compliance dacqurir les informations correspondantes. Please notice that if the ISED certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains IC: 21015-MWBWB01 any similar wording that expresses the same meaning may be used. l'appareil hte doit porter une tiquette donnant le numro de certification du module d'Industrie Canada, prcd des mots Contient un module d'mission ,du mot IC: 21015-MWBWB01 ou d'une formulation similaire exprimant le mme sens, comme suit This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter and must be installed to provide a separation distance of at least 20cm from all persons Cet metteur ne doit pas tre situ en mme temps ou fonctionner en liaison avec une autre antenne ou un autre metteur et doit tre install de manire assurer une distance de sparation dau moins 20cm de toutes les personnes The modular can be installed or integrated in mobile or fix devices only. This modular cannot be installed in any portable device, for example, USB dongle like transmitters is forbidden. PAGE 5 OF 6 Version 1.0 PRODUCTS USERMANUAL MWB1830-WB01 When the module is installed inside another device, the user manual of this device must contain below warning statements;

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licenceexempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the device. L'metteur/rcepteurexempt de licence contenu dans le prsent appareil est conforme aux CNR d'Innovation. Sciences et DveloppementconomiqueCanada applicables aux appareils radio exempts de licence.. Lexploitation est autorise aux deux conditions suivantes :

(1) lappareil ne doit pas produire de brouillage;

(2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. PAGE 6 OF 6 Version 1.0

13.8 16,00 ee wODEL: MWB1830-WBO1 FCC ID:VG8MWBWB01 1C:21015-MWBWB01 cuit 1: 2021DP 11684 RAB HARA)

GUANGDONG MIDEA KITCHEN APPLIANCES MANUFACTURING CO., LTD. 12/1/2021 Nemko North America, Inc. 303 River Road Ottawa, Ontario, Canada K1V 1H2 REQUEST FOR CONFIDENTIALITY - FCC FCC ID: VG8MWBWB01 Pursuant to Sections 0.457(d)(1)(ii) and 0.459 of the Commissions Rules and FCC Guidance document 726920, we hereby request confidential treatment of information accompanying this application as outlined below:

PERMANENT LONG-TERM CONFIDENTIALITY:

Schematics Block Diagrams Theory of Operation When the device is marketed before the requested number of days listed above, the grantee will inform the TCB to release the Short-Term Confidentiality information withheld on the FCC equipment authorization website. The above information contains trade secrets and proprietary information not customarily released to the public. The public disclosure of this information might be harmful to the applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this Application and all accompanying materials will not be made before the date of the Grant for this Application. Sincerely, Signed:

Printed name: Xue wenfei Title: Certification Engineer