User manual 1Model and Product name: Forza 60B LED Bi-color Spot Light 2Technical data:
Input: AC 100-240V 50/60Hz Output: DC 15V/6A Max.90W Color Temperature: 2700-6500K CRI: 95 TLCI: 98 3Detailed Description 1LCD screen: For displaying the data. 2Left knob: For adjusting the DIM and scrolling through different selections. 3DC inlet: DC power input socket. 4MODE button: For switching between EFFECT mode, CCT mode and MENU. 5Right knob: For selecting options and adjusting the color temperature under CCT mode. 6Power switch: For switching on/off the fixture. 7DMX inlet: For DMX input socket. 42.4G and Bluetooth Remote Control The Forza 60B is able to be remotely controlled by 2.4G remote controller, or by NANLINK APP via the WS-TB-1 transmitter box or via Bluetooth directly. Note:
12.4G remote controller and transmitter box are sold separately. 2The fixture supports the 2.4G wireless protocol V1.0 and V2.0. Please set fixture to V2.0 while using WS-RC-C1 or WS-RC-C2 remote controller. Please set fixture to V1.0 while using other remote controllers. 5Safety Precautions 1Please open the package to check for damage caused in transit, if damaged please do not use and contact place of purchase or manufacturer as soon as possible. 2Please do not use a power cord with damaged insulation, do not unplug too hard or drag the power cord directly. 3Make sure that the power supply voltage used matches the voltage designated by the light before installation. 4Please turn the light off when it is not in use or before cleaning. 5Please keep the light safely stored and away from children. 6Notice 1Please take off the COB protective cap before using. 2Please do not look directly at the emitter when the light is on . 3Please wait 10 seconds to turn off the light fixture after any parameter setting in order to save it for future use. 4Please do not place any objects on the light emitter or allow liquid to flow inside the fixture or the emitter. 5Please do not place the light fixure near the flammable substances like alcohol or gasoline. 6Please wipe off debris or dirt by using a cloth with clean water or neutral cleanser when cleaning the light. 7The fixture should be used in dry and ventilated place and avoid being used in damp, dusty or overheated environment, also make sure the fan and the vents are not blocked or obstructed. 8Any attempt to repair the fixture by yourself will void warranty, disasembling and repair can only be allowed when trained professionals are involved under strict protocal regulated in this manual. 9For optimal cooling of the fixture, the vents should not be covered when using, or might result in damaging the equipment. The temperature on the fixture surface is high when using for a long time, please caution to prevent burns and scalds. 7FCC Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
1) this device may not cause harmful interference. 2) this device must accept any interference received, including interference that may cause undesired operation. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.