FCC ID: 2A2Y8-FORZA720B LED Bi-color Spot Light

User manual 1Model and Product name: Forza 720B LED Bi-color Spot Light 2Technical data:

Input: AC 100-240V 50/60Hz Output: DC 48V/16.67A Max. 800W Color Temperature: 2700-6500K CRI: 96 TLCI: 97 32.4GBluetooth Remote Control Forza 720B is able to be remotely controlled by 2.4G remote controller, or by NANLINK APP via the transmitter box or via Bluetooth directly. Note:

12.4G remote controller and transmitter box are sold separately. 2The fixture supports the 2.4G wireless protocol V1.0 and V2.0. Please set fixture to V2.0 while using WS-RC-C1 or WS-RC-C2 remote controller. Please set fixture to V1.0 while using other remote controllers. 4Safety Precautions 1Please open the package to check for damage caused in transit, if damaged please do not use and contact place of purchase or manufacturer as soon as possible. 2Please do not use a power cord with damaged insulation, do not unplug too hard or drag the power cord directly. 3Make sure that the power supply voltage used matches the voltage designated by the light before installation. 4Please turn the light off when it is not in use or before cleaning. 5Please keep the light safely stored and away from children. 5Notice 1Please take off the COB protective cap before using. 2Please do not look directly at the emitter when the light is on . 3Please wait 10 seconds to turn off the light fixture after any parameter setting in order to save it for future use. 4Please do not place any objects on the light emitter or allow liquid to flow inside the fixture or the emitter. 5Please do not place the light fixure near the flammable substances like alcohol or gasoline. 6Please wipe off debris or dirt by using a cloth with clean water or neutral cleanser when cleaning the light. 7The fixture should be used in dry and ventilated place and avoid being used in damp, dusty or overheated environment, also make sure the fan and the vents are not blocked or obstructed. 8Any attempt to repair the fixture by yourself will void warranty, disasembling and repair can only be allowed when trained professionals are involved under strict protocal regulated in this manual. 9For optimal cooling of the fixture, the vents should not be covered when using, or might result in damaging the equipment. The temperature on the fixture surface is high when using for a long time, please caution to prevent burns and scalds. 6FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Label Location On EUT Label Product Name: LED Bi-color Spot Light Model No.: Forza 720B FCC ID: 2A2Y8-FORZA720B This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation.

Product Number: NB2400-128 Product Name: 2.4GHz Antenna Specification For Approval Date: 2021 / 03 / 19 File No.:

Version: 1.0 Customer Customer P/N /

Yi Zong P/N NB2400-128 Description : 2.4GHz Antenna Cortec Checked By:

menna.Tao Customer Approved By:

janes.LI Page 1 Product Number: NB2400-128 Product Name: 2.4GHz Antenna Index:

1. Revision History / Page 3 2. Specification / Page 4 3. Characteristics and Reliability Test / Page 5 4. Antenna - S Parameter Test Data / Page 6 5. Antenna - Radiation Pattern Test Data / Page 7 6. Mechanical and Packing Drawing / Page 8 ~ 9 Page 2 Product Number: NB2400-128 Product Name: 2.4GHz Antenna 1. Revision History Revision Date Change Notification Description 1.0 2021.03.19 Page 3 Product Number: NB2400-128 Product Name: 2.4GHz Antenna 2. Specification Sample Photo A. Electrical Characteristics Frequency V.S.W.R. Peak Gain Polarization Impedance 2400 ~ 2500 MHz 2.0 2.0 dBi Linear 50 Ohm B. Material & Mechanical Characteristics Material of Radiator CU Cable Type Connector Type C. Environmental OD1.13mm Mini Connector Operation Temperature

- 40 C ~ + 65 C Storage Temperature

- 40 C ~ + 80 C Page 4 Product Number: NB2400-128 Product Name: 2.4GHz Antenna 3. Characteristics and Reliability Test Test Items Test Condition and Procedure Requirements C1 S.W.R. Set DUT on Network Analyzer; make individual Directive DUT specification calibration to test C2 Antenna Set DUT on Antenna Chamber; make individual Directive DUT specification Gain calibration to test M1 Vibration GB / T2423 . 48-1997 1. No Visual Damage Amplitude: 0.03 inch (1.5mm); Freq: 20 to 80 to 20 Hz 2. Frequency Tol.<= 5%

3 directions; 2 hours for each direction M2 Random GB / T2423.8-1995 Drop Height: 1.0 Meter;

1. No parts separated 2. Frequency Tol.<= 5%

3 directions; 1 time for each direction M3 Solderability GB 2423 . 28- 82 1. Mounted on PCB Solder iron: 2605C; Duration: 5 seconds 2. No Visual Damage M4 Terminal-

Holding with individual specification; force applied 1. Directive DUT specification Pull Test to axis of terminal 2. Frequency Tol.<= 5%

M5 Terminal-

Holding with individual specification; applied 1. Directive DUT specification Torque Test clockwise and counterclockwise to the axis of 2. Frequency Tol.<= 5%

terminal M6 Dimension Inspection of dimension, color, material, package, Directive DUT specification surface process E1 Salt Spray GB / T 2423 . 17- 93 After 2 Hours Recovery Temp: 35C; RH: >= 95%; NaCl solution: >= 5%;

1. No Visual Damage Time: 24 hours E2 Humidity GB / T 2423 . 4 - 93 2. Frequency Tol.<= 5%

After 2 Hours Recovery Temp: 80C / 12 H; -40C / 12H RH: >= 90%;

1. No Visual Damage Time: 24 hours E3 Thermal GB / T 2423 . 22 - 87 2. Frequency Tol.<= 5%

After 2 Hours Recovery Shock 1 Cycle: - 40C (30 minutes) to + 80C (30 minutes) 1. No Visual Damage Cycles: 24 E4 Life (High GB /T 2423 . 2 - 89 Temp.) Temp: 80C; Time: 24 hours 2. Frequency Tol.<= 5%

After 2 Hours Recovery 1. No Visual Damage 2. Frequency Tol.<= 5%

R1 RoHS With Reference to IEC 62321:2008 with flow chart Directive RoHS 2011/65/EU R2 PFOS With Reference to USA EPA 3540C:1996 by LC/MS Directive RoHS 2006/122/EC R3 PFOA With Reference to USA EPA 3540C:1996 by LC/MS Directive RoHS 2006/122/EC Page 5 Product Number: NB2400-128 Product Name: 2.4GHz Antenna 4. Antenna - S Parameter Test Data Page 6 Product Number: NB2400-128 Product Name: 2.4GHz Antenna 5. Antenna - Radiation Pattern Test Data 2400 MHz 2450 MHz 2500 MHz 6. Mechanical Drawing See attached files Page 7

Guangdong Nanguang Photo&Video Systems Co., Ltd. Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 U.S. Agent Designation 5/31/23

[Guangdong Nanguang Photo&Video Systems Co., Ltd.] acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought (FCC ID: [2A2Y8-FORZA720B]):

Name and company of U.S. agent: Mamiya America Corp Physical U.S. address of agent: 75 Virginia Rd N. White Plains, NY 10603 United States FRN of U.S. agent: 0033618356 Email address of U.S. agent: waynes@macgroupus.com

[Mamiya America Corp] acknowledges their obligation to accept service of process on behalf of

[Guangdong Nanguang Photo&Video Systems Co., Ltd.].

[Guangdong Nanguang Photo&Video Systems Co., Ltd.] with the FRN [0031307127] accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under 2.911(d)(7). Sincerely, 4 0 V

, U

) 7

) d

1 1 9 2 _ t n e g A _ S U

l e d o m

_ 8 4 The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB.

Guangdong Nanguang Photo&Video Systems Co., Ltd. Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 5/29/23 To whom it may concern:

We, [Guangdong Nanguang Photo&Video Systems Co., Ltd.], hereby certify that the equipment for which authorization is sought (FCC ID: [2A2Y8-FORZA720B]) is not covered equipment prohibited from receiving an equipment authorization pursuant to 2.903 of the FCC rules. We also certify that, as of the date of the filing of the application, we are not identified on the Covered List (https://www.fcc.gov/supplychain/coveredlist) as an entity producing covered equipment. By signing this form, we confirm the above and that we are aware of the application requirements listed under 2.911(b) and (d)(5) and (6). Sincerely, 2 0 V

, U

) i i

d n a

) i

) 5

) d

1 1 9 2 _ u q E d e r e v o C

l e d o m

_ 2 6 Signature

[Junhua Lin]

[Manager]

Guangdong Nanguang Photo&Video Systems Co., Ltd. The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01.