FCC ID: QV7-GC88752-51 R/C CAR

K-16 Instruction Manual of Mini Twister Car

Notes：

-Ensure adult supervision at all times

-This product is not suitable for children aged 6 or under. When using electrical products, precautions must be taken to preve nt the risk of an electric shock.

-Do not attempt to modify or re-assemble this product. Unauthorized changes may void your right to use the product.

-There are small parts in this product. The children should play it with the guard of the adults, and never swallow the small parts into their mouth.

Thank you for purchasing one of our toy products. To ensure that you get the most out of your

new purchase, please read these instructions carefully before using the toy for the first time.

They contain important information on how to operate the product.

TTwwiisstteerr

CCaarr

Inserting the remote control batteries

Remote control

1. Check the ON/OFF switch is in the “OFF”

position.

2. Use a screwdriver to loosen the screw.

3.Remove the battery cover.

4. According the polarity indicated inside in the

remote control. Put the 2*AAA battery into the

battery compartment.

5. Put the battery cover back and tighten

the screw.

Note: If breakdown occurs in the product, please take

out the battery for one minute, and then reinstall it. If

The battery can only be installed by the adults.

Charging the batteries

2X1.5V“AAA”

· Connect the USB charger to USB output on computer or AC/DC adaptor,then insert the car charger plug to

the USB wire charger.(Make sure in a correct polarity)

· A full charge takes 70 minutes. When charging the LED indicator turns into red,when charging is complete,

the LED indicator stays off.

· Regularly inspect the toy, battery charger, charging cable, connectors and other components for signs of

damage. In the event of any damage, discontinue use and send the parts for repair.

· In case of abnormal responses such as suspicious peculiar smell, noise or smog in the charger,please

remove the power supply at once.

the breakdown still exists, please replace the battery.

Sketch Map of Installed Battery in the Remote Control

Caution

· Please recharge with the dedicated USB delivered by the original

factory. Never use broken USB or USB of other brands.

· Please do not overcharge the battery. When the battery is fully

recharged, please pull out the charger.

· Please do not recharge on the surface of the objects near

inflammable things(carpet, wood floor,solid wood furniture, etc.)

or of conductive things. While recharging, please keep the battery

within the range of visibility.

Charging diagram of

USB charging line

Battery safety information

1. The batteries must only be charged under adult supervision.

2. Before charging the batteries, remove the battery compartment from the vehicle chassis.

3.Remove empty batteries from the vehicle and remote control.

4. Ensure that the vehicle is switched off before inserting the batteries.

5. Install the battery according to the instruction inside the battery box. Make sure not to confuse the

positive and negative polarity of the battery.

6. Do not attempt to charge non-rechargeable batteries.

7.Do not short circuit the battery terminals.

8. If you do not plan to use the vehicle for an extended period, remove the batteries from the vehicle and

remote control to prevent leakage.

9. Do not throw batteries into open flames, as this may cause them to explode or leak.

10.Do not mix old and new batteries or batteries from different manufacturers.

11.Only use batteries from recommended or reputable manufacturers.

12.Regularly inspect the batteries for signs of leakage.

13. It is suggested not to use more than 3 batteries for one single play.

14. If leaking occurs in the battery, please avoid touching the liquid with the skin and eyes.If it touches the skin,

please clean the skin with soap and clean water at once. If it touches the eyes, please wash the eyes with

a lot of cold water at once and see the doctor right away.

15. This equipment is composed of electronic components and battery. The electric appliance garbage

should be given special care according to the local requirements for garbage disposal.

16. Keep this instruction manual in a safe place for future reference. It contains important information on

how to use the product safely.

Care and maintenance

· Remove the batteries when you do not plan to use the toy for an extended period.

· Use a damp cloth to wipe the vehicle clean.

· Do not expose the toy to high temperatures, moisture or direct sunlight.

· Do not immerse the toy in water, as this may damage the electrical components.

·If the wheel is too dirty or rolls inflexibly, this may influence the operation experience.

Please check it and clear up the foreign matters.

· When the wheels of remote control car is rolling, Do not touch it in order to avoid injury of

yourself or damage of the car.

· Please do not play by the road or in dangerous places in case of accidents.

· Avoid operating the vehicle in the rain or grinding the remote control vehicle over the puddle

in case of breakdown.

·Avoid operating the vehicle alongside the river, lake or pond in case the remote control or remote

control vehicle fall into the water.

· Please take out the batteries from remote control when not using.

Introduce the function of the remote control and the vehicle

360° left rotation

360° right rotation

Charging port

ON/OFF

Indication Gravity Induction

lamp

Mode Switching

ON/OFF

Transform

Demo 1

Control bar

Demo 2

Demo 3

·Demo 1：Short press on Demo 1 key for a variety of functional demonstrations. (Different Demo keys have

·Push the control level to the left, the car will spin

clockwise on site

·Push the control level to the right, the car will spin

anti-clockwise on site.

·Demo 2：Short press on Demo 2 key for a variety of functional demonstrations. (Different Demo keys have

Forward(Gravity induction mode)

Backward(Gravity induction mode)

·Demo 3：Short press on Demo 3 key for a variety of functional demonstrations. (Different Demo keys have

Incline down the

remote control horizontally

Incline up the

remote control horizontally

different music).

different music).

different music).

·Transform：Short press Transform key , the car will transform.

·Mode Switch：Short press “Mode” key to switch the mode of car, the car will change from 360degree rotation

·Control level：Short press the control level to change the sound effect of the car, please check the operation

to left-right moving.

instruction to see more functions.

Using the vehicle

· Switch on the vehicle using the ON/OFF switch.

· Switch on the vehicle ON/OFF switch,make the frequency of the remote control and remote control

vehicle match each other,then you can operate the remote control vehicle.

· Switch off the vehicle and remote control after use.

·The playing time is about 35 mins.

·The control rang is about 40 meters, if out of 40 meters rang , it may lose control.

Keep pressing on the

Gravity Induction key

Keep pressing on the

Gravity Induction key

·Keep pressing on the Gravity Induction key, incline

down the remote control horizontally, then the car

will move forwards

·Keep pressing on the Gravity Induction key, incline

up the remote control horizontally, then the car will

move backwards

360° left rotation(Gravity induction mode)

360° right rotation(Gravity induction mode)

In order to avoid losing the remote control vehicle or making it lose control, follow the following steps all the time:

1.Turn on the remote control.2.Turn on the remote control car.

Turn it off according to the opposite steps.

Function and operation of the product

Incline left the remote

control horizontally

Incline right the remote

control horizontally

Keep pressing on the

Gravity Induction key

Keep pressing on the

Gravity Induction key

Caution：

Transform

·Keep pressing on the Gravity Induction key, incline

left the remote control horizontally, the car will spin

clockwise on site

·Keep pressing on the Gravity Induction key, incline

right the remote control horizontally, the car will spin

anti-clockwise on site

· Press the deformation function key to make it into off-road state ,then press again to make it into

sports car state

Forward

Backward

Transform

key

·Push the control level forwards, the car will move

forwards

·Push the control level backwards, the car will move

backwards.

Note: It is strictly prohibited to

put your finger on the deformed

joint when the car turn on the

switch for frequency and

deformation, so as not to hurt

your finger.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

Receive:

FCC ID: QV7-GC88752-54

Launch:

FCC ID: QV7-GC88752-51

FCC ID : QV7-GC88752-51 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Label size: 3cm*5cm

GUANGDONG SYMA MODEL AIRCRAFT INDUSTRIAL CO., LTD.

TO:

Federal Communication Commission

Equipment Authorization Branch

7435 Oakland Mills Road

Columbia, MID 21046

Confidentiality Request regarding application for FCC ID: QV7-GC88752-51

Regarding:

LONG TERM CONFIDENTIALITY

Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential

treatment of the documents listed below, associated with the certification application referenced above.

Schematic(s)

Block Diagrams

Operational Descriptions

The documents above contain proprietary information not released to the public. Public disclosure of this

information may prove harmful to the business of the applicant.

Sincerely,

Title:Manager

Print Name:

Signature:

On behalf of Company: GUANGDONG SYMA MODEL AIRCRAFT INDUSTRIAL CO., LTD.

Telephone:0754-86381898

E-mail: syma@symatoys.com

a)

b)

c)

d)

e)

f)

g)

SGS North America Inc.

620 Old Peachtree Road

SUITE 100

Suwanee, Georgia 30024

United States

Applicant Declaration

Applicant Legal Business Name

GUANGDONG SYMA MODEL AIRCRAFT INDUSTRIAL CO., LTD.

No. 2 West Xingye Road Laimei Industrial Area,Chenghai Shantou China

Address

Grantee Code

FCC ID

Contact Email

Contact Phone

Authorized Contact Name

Ivan Chen

QV7

QV7-GC88752-51

syma@symatoys.com

0754-86381898

I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare;

in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my

knowledge and belief.

in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in

this application, the Applicant is responsible for:

labeling the equipment with the exact FCC ID as specified in this application,

(1)

(2) compliance statement labeling pursuant to the applicable rules,

(3) compliance of the equipment with the applicable technical rules,

if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure

that production units of this equipment will continue to comply with the FCC’s technical requirements.

in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible

party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321.

in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts

and agrees to abide by the post market surveillance requirements.

(1)

(2)

(3)

the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing.

the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED.

the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS,

FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or

software required for evaluation, review, certification and audit surveillance of products certified by SGS.

neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section

5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See

47CFR 1.2002(b) for the definition of a “party” for these purposes.

the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions.

Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47

Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm

Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html

Applicant Signature:

Date:2021-6-30

Print Name:

Title:

*NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database

Manager

Applicant Declaration

Rev:0.0

GUANGDONG SYMA MODEL AIRCRAFT INDUSTRIAL CO., LTD. TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Date: 2021-6-30 Regarding: FCC ID:QV7-GC88752-51 To whom it may concern:

We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch and Keny Xu in SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with GUANGDONG SYMA MODEL AIRCRAFT INDUSTRIAL CO., LTD. This authorization is valid until further written notice from the applicant. Title:Manager Print Name:

Signature:

On behalf of Company: GUANGDONG SYMA MODEL AIRCRAFT INDUSTRIAL CO., LTD. Telephone:0754-86381898 E-mail: syma@symatoys.com