FCC ID: QV7-GC88752-52 STUNT SPEEDER

6+

User Manual

Safety information:

1.Switch off the product before charging the battery, and then connect the USB charging cable (ensure that the

charging connector is connected in the correct orientation).

2.Connect the USB charging cable to a mobile USB charger or computer USB port. The indicator light on the USB

charging cable will turn on to indicate that charging is in progress and switch off when charging is complete.

3.Pairing instructions: Switch on the vehicle. The indicator light will start to flash. Switch on the remote control and

wait for the remote control indicator to flash. The devices will pair automatically and the indicator lights will switch off

simultaneously when pairing is complete. After use, switch off the vehicle and remote control to preserve battery power.

Important safety information

Thank you for buying this REVOLT item. To ensure that you operate the vehicle correctly, please read these

instructions carefully before first use and store them in a safe place for future reference.

Safety information

*Keep the smaller-sized accessories out of the reach of children.

*Do not store batteries in a hot environment (e.g. near open flames or a heating device).

*Children must be supervised by an adult when operating the vehicle. The vehicle should always remain within the

line of sight of the driver (or instructor).

*Do not recharge non-rechargeable batteries. When installing or changing the batteries, ensure that they are

connected in the correct polarity. Do not mix old and new batteries or different types of batteries.

*Do not short circuit the battery terminals.

*If you do not plan to use the vehicle for at least 10 days, discharge the battery to 40%-50% (i.e. if the battery is fully

charged, drive the vehicle for half of the total driving time). This helps to prolong the lifespan of the battery.

*You must only use the charging cable provided. Disconnect the model from the charging cable before cleaning .

Regularly inspect the charging cable’s wires, plug socket, outer casing and other accessories to ensure that they are

not damaged.If there are any signs of damage, discontinue use immediately until the fault has been repaired.

*After use, ensure that the vehicle and remote control are switched off and remove the batteries in the remote control.

*The packaging and this manual contain important information and should be kept in a safe place for future reference.

Repair and maintenance

*Clean the product regularly with a clean, soft cloth.

*Avoid exposing the product to direct sunlight or heat.

*Do not submerge the product in water, as this may damage the electrical components.

About this product

Specifications

Remote controlled vehicle

Weight 64.5g (including battery)

Dimensions 13.5x8x5 cm

Remote control range 15-20m

Operating temperature 0 to 40 °C

Battery 3.7V 200mAh rechargeble battery (included)

Remote control

Operating frequency 2.4 GHz

Operating temperature 0 to 40 °C

Battery Requirements 2x AA 1.5V Batteries (not included)

Ramp

Weight 25g

Dimensions 19x11x7.5cm

Operating the vehicle and remote control

Fig. 3 Performing a programmed sequence of Programming mode

turn left

turn right

On/off Switch

ON/OFF

Programming

button

LED indicator

Reverse

Forward

forwards/backwards

←Forwards

→Reverse

(speed is adjustable)

Important:

Ensure that the power switch is in the “ON” position,

otherwise the vehicle will not respond to the remote control.

Programming

button

Press the programming

button again

The vehicle will perform

the programmed sequence

of movements

4. To reprogram the sequence of movements, follow the instructions in figure 1.

Note:

①The remote control will automatically exit programming mode after 8 seconds of inactivity. If you entered

a sequence a movements, the sequence will be automatically saved.

②If you did not enter a sequence of movements, the remote control will automatically retain the most

recently programmed sequence.

③To stop the vehicle when it is performing your programmed sequence of movements, move the forwards,

reverse, left or right controls.

④If the remote control batteries are depleted when you attempt to program a sequence of movements,

your sequence will not be saved. If this occurs, replace the batteries and try again.

USB

Programming a sequence of movements

1.The remote control can be programmed to perform a sequence of movements. After pairing the vehicle with the

remote control, enter programming mode by holding down the programming button for 2 seconds until the LED

indicator starts to flash. Example: Forwards + turn left + turn right, reverse + turn left + turn right, forwards + reverse

+ turn left. You can program up to 14 movements.

charging socket

Important:

only use the charging cable provided.

Fig 1. Hold down the programming button to

enter programming mode

Fig. 2 Programming a sequence of

movements

Operation Frequency:2410MHz to 2473MHz

MAX OUTPUT POWER:7.125dBm（for EU）

Charging the vehicle battery

LED indicator

Charging the built-in vehicle battery

Installing the remote control batteries

· Remove the screw from the battery compartment cover.

· Slide to open the battery compartment.

· Insert 2 x AA 1.5V batteries (not included).

· Make sure to observe the polarity symbols inside the

battery compartment and insert the batteries accordingly.

· Replace battery compartment cover and screw.

1.5V“AA”

1.5V“AA”

2.After programming the desired movements, press the programming button to exit programming mode.

The LED indicator will switch off.

3.To perform the programmed sequence of movements, press the programming button.

Programming button

Flashing indicator

Turn left

Turn right

Forwards

Increase speed

Warning: Changes or modifications to this unit not expressly app-

roved by the party responsible for compliance could void the users

authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules These limits are designed to provide reasonable prote-

ction against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy

and, if not \installed and used in accordance with the instructions,

may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interfe-

rence to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver

Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

“This device complies with FCC radiation exposure limits set forth

for general population(uncontrolled exposure).This device must not

be collocated or operating in conjunction with any other antenna or

transmitter.”

Decoration of Conformity Inserts：

“Hereby, GuangDong Syma model drone Industrial co, ltd, declares

that this TG1007

is in compliance with the essential requirements and

other relevant provisions of Directive 2014/53/EU.”

A copy of the full DoC is attached.

The materials, specifications, parts and packaging mentioned in this manual are for

reference purposes only. We are not responsible for any changes made to this printed

material, nor are we able to inform customers of any updates or changes. Please refer

to our website: R3VOLT.COM for the latest information.

Address: Intersection of Xingye Road No. 2 (West side) and Xingye Road (North side), Laimei Industrial

Park, Chenghai District, Shantou, Guangdong Province, China

Sales hotline: 0754-86980668, After-sales hotline: 0754-86395095

Fax: 0754-86395098 Zip code: 515800

The manufacturer the right to the final interpretation of this instruction manual.

FCC ID : QV7-GC88752-52 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Label size: 3cm*5cm

GUANGDONG SYMA MODEL AIRCRAFT INDUSTRIAL CO., LTD Date: 2021-05-11 TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: QV7-GC88752-52 To whom it may concern:

We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch and Keny Xu in SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with GUANGDONG SYMA MODEL AIRCRAFT INDUSTRIAL CO., LTD. This authorization is valid until further written notice from the applicant. Title: Sale Director Print Name:

Signature:

On behalf of Company: GUANGDONG SYMA MODEL AIRCRAFT INDUSTRIAL CO., LTD Telephone: 0754-86381898 E-mail: syma@symatoys.com

Date: 2021-05-11

Confidentiality Request regarding application for FCC ID: QV7-GC88752-52

To:

Federal Communications Commission

Office of Engineering and Technology Laboratory Division

7435 Oakland Mills Rd.

Columbia MD 21046

From: GUANGDONG SYMA MODEL AIRCRAFT INDUSTRIAL CO., LTD

Regarding:

LONG TERM CONFIDENTIALITY

Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby requests confidential

treatment of the documents listed below, associated with the certification application referenced above.

Schematic(s)

Block Diagrams

Operational Descriptions

The documents above contain proprietary information not released to the public. Public disclosure of this information may

prove harmful to the business of the applicant.

Title: Sale Director

Print Name:

Signature:

On behalf of Company: GUANGDONG SYMA MODEL AIRCRAFT INDUSTRIAL CO., LTD

Telephone: 0754-86381898

E-mail: syma@symatoys.com

a)

b)

c)

d)

e)

f)

g)

SGS North America Inc.

620 Old Peachtree Road

SUITE 100

Suwanee, Georgia 30024

United States

Applicant Declaration

Applicant Legal Business Name

GUANGDONG SYMA MODEL AIRCRAFT INDUSTRIAL CO., LTD

NO.2 WEST XINGYE ROAD LAIMEI INDUSTRIAL AREA CHENG HAI Shantou China

Address

Grantee Code

FCC ID

Contact Email

Contact Phone

Authorized Contact Name

Ivan Chen

QV7

QV7-GC88752-52

syma@symatoys.com

0754-86381898

I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare;

in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my

knowledge and belief.

in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in

this application, the Applicant is responsible for:

labeling the equipment with the exact FCC ID as specified in this application,

(1)

(2) compliance statement labeling pursuant to the applicable rules,

(3) compliance of the equipment with the applicable technical rules,

if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure

that production units of this equipment will continue to comply with the FCC’s technical requirements.

in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible

party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321.

in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts

and agrees to abide by the post market surveillance requirements.

(1)

(2)

(3)

the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing.

the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED.

the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS,

FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or

software required for evaluation, review, certification and audit surveillance of products certified by SGS.

neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section

5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See

47CFR 1.2002(b) for the definition of a “party” for these purposes.

the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions.

Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47

Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm

Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html

Applicant Signature:

Date: 2021-5-11

Applicant Declaration

Rev:0.0

Print Name:

SGS North America Inc.

620 Old Peachtree Road

SUITE 100

Suwanee, Georgia 30024

United States

Applicant Declaration

Title:

Sale Director

*NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database

Applicant Declaration

Rev:0.0