QUICK START GUIDE Reader Applicable Model: TD-RM01TD-RM02 TD-RM03TD-RM04 Version : 1.0 Date : May 2023 Touching the future 1Product Overview Parameter:
Working voltage DC12V10%
Swipe distance 0~4CM Working current 80MA Card reading type IC card Communication mode Wegen 26 / Wegen 34 issuing mode management platform card issuing Working temperature
-20~70 Card capacity 1000 Relative humidity 20% ~ 93%
Open mode swipe card, APP, remote, password (optional) size 86 * 86 * 8MM Installation method Control box: hanging installation reading head : 86 box embedded installation.86 box requires a depth of 50MM inside 2Wiegand Reader Installation diagram:
(a) Connect the signal line in the back of the read head device as shown in the figure below. Back Signal wire interface
(b) Install the reading head device into the 86 box, (note that you need to use the embedded wall inside the depth of 50MM style 86 box), lock the screws to fix, as shown in the figure below. Front Fixing screws
(c) Read the head panel and read the head body snap together, first from the upper snap down and then press the lower and bottom screw hole alignment; finally in the bottom of the anti-theft screw hole screwed on the countersunk head machine wire within the plum security screws fixed,as shown in the figure below. Bottom Locking plum security screw hole 3Wiring instruction Operating mode selection Wire color Function Description Red Line Blace Line Green Line White Line Yellow Line Blue Line DC12V GND D0 D1 WG34 LED/BZ Notes 1.Before powering up, you must confirm the voltage of the power supply and the positive and negative terminals of the power supply. 2.When using external power supply, it is recommended to share the power ground with the controller power supply. 3.Read the head to the control box wire, it is recommended to use 8-core shielded multi-strand twisted pair network cable. Three of the cores standby, if you do not need to read the head sound and LED light feedback legal card, may not be connected to LED/BZ line, Wegen data line D0 and D1 is recommended for each other better twisted pair, line cross-
sectional area recommended 0.22 square millimeters or more, it is recommended that the wiring length does not exceed 100 meters, shielded wire connected to the control box motherboard GND, thickened or double stranded together a power supply to the reading head, help to enhance the performance of the reading head. (You can also use other multi-core shielded Category 5 wire) www.trudian.com/en/
HQ Add: Farbell Technology Park,Yixian Road, Nanlang, Cuiheng New District, Zhongshan City, Guangdong Province, China. Zip Code:528451 Phone: +86 0760 - 23689666 E-mail: sales@trudian.com If the problem is not solved properly,please send the mail to:
support@trudian.com FCC Caution This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.