FCC ID: 2AZ7PG2800 Rove G2800 Gyroscope Navigation Robot Vacuum Cleaner

 

ROVE

Rove G2800 Gyroscope Navigation

Robot Vacuum Cleaner

User Manual

G2800

ROVE

from

APPLIED SCIENCE

C O N T E N T S

ROVE

SAFETY INFORMATION .................................................................................................................................. 1

WARNING ................................................................................................................................................................ 4

PRODUCT INTRODUCTION ............................................................................................................................... 5

ROVE SETUP.........…………............................................................................................................................................... 8

USAGE INSTRUCTION .....…………...................................................................................................................... 9

ROUTINE MAINTENANCE ......................................................................................................................................12

PRODUCT INFORMATION ...................................................................................................................................15

TROUBLESHOOTING GUIDE .................................................................................................................................16

COMMON PROBLEMS .......................................................................................................................................18

WARRANTY ...............................................................................................................................................................19

FCC STATEMENT ....................................................................................................................................................20

SAFETY INFOMRATION

Usage Limitations

ROVE

• This product is to be used for floor cleaning inside a home ONLY and cannot be used outside of the house, on non-ground surfaces (such

as furniture) and not for commercial/industrial environments.

• Please do not operate the product when the temperature is below 32°F or above 104°F, on wet surfaces, or over sticky substances.

• Please ensure there is no wiring on the floor that the vacuum can get tangled in, including the vacuum charging station wiring.

• Please remove fragile objects (such as vases, plastic bags, etc.) on the floor to prevent device from being damaged.

• Adult supervision is required.

• Please keep main brush and other cleaning tools away from children.

• Do not place anything on the vacuum while it's on.

• Never let clothing or body parts (such as hair, nails, etc.) be drawn into the brush or wheel of this device, otherwise it may cause personal

injury.

• Please do not use this product to sweep burning objects (such as burning cigarettes , matches, etc.).

• This product is not intended for use with extra long fiber carpet (some carpets may need to be cleaned differently).

• Please keep this device away from hard or sharp objects (such as glass, iron nails, etc.).

• Please do not move the machine by holding the protective cover of the LiDAR and collision bumper.

• Please regularly clean and maintain the device and the charging base when shut off or in the power-off state.

• Please do not wipe any part of the product using a wet cloth or any other liquid.

• Please use this product only in accordance with the instructions in this User Manual to avoid damage to the product or home furnishings,

and to avoid personal injury. Keep the User Manual for future reference.

1

ROVE

SAFETY INFORMATION

1. This device is only to be used with the power supply unit provided with it.

2. The adapter must be removed from the socket-outlet before cleaning or maintaining the device.

3. This device contains batteries that are only replaceable by skilled persons.

4. The battery must be removed from the device before it is disposed of.

5. This device must be disconnected from the power supply when removing the battery.

6. The battery is to be disposed of safely.

7. WARNING: For the purposes of recharging the battery, only use the detachable power supply unit provided with this device.

Plug Type

USA

Model

NLD100240W1A4

Input

AC- 100- 240V 50/60Hz 0.6A

Output

DC- 24V1A

Battery and Charging

• Please do not use a battery, charging base or charger provided by any third parties.

• Please do not dismantle or refit the battery a n d charging base.

• Please keep the charging base a wa y from heat sources (such a s a heating plate).

• Please do not wipe or clean the charging base using a wet cloth or wet hand.

• Please do not im properly dispose of used batteries. Used batteries should be disposed of by a professional recycling agency.

•

If the power line is d a m a g e d or broken, please stop using it immediately a n d replace it with official Applied Science products.

• Please ensure the robot is turned off during transportation a n d the product should be transported in its original packaging.

•

If the device is left unused for too long, it should be fully charged a n d then placed in a cool a n d dry place. Charge the device at

least every 3 months, to avoid d a m a g i n g the batteries due to excessive discharge.

2

SAFTETY INFORMATION

ROVE

• The following information is only applicable to the disposal of this device, not its daily use.

• The chemical substances contained in the battery will pollute the environment. Before disposing of this product, remove the

battery and take it to a professional recycling station. The battery should only be removed after it has been used completely.

Do not under any circumstance allow the battery to come into contact with metal objects.

1. Ensure that the robot is not touching the charging base, keep the product running until it uses up all of the battery and shuts

2. Remove the screws from the battery cover.

3. Remove the battery cover, pull out the battery plug, and then remove the battery.

Disposal Instructions:

Removing the Battery:

down.

Frequency

Noise Level

2.4Ghz~2.4835Ghz

≤ 17dBm

3

WARNING !

ROVE

This symbol means that according to local laws and regulations, your product and/or its battery

shall be disposed of separately from regular household waste. W hen this product reaches the

end of its life, users have the choice to give this product to a competent recycling organization.

Proper recycling of your product will protect human health and the environment.

Indoor use only.

BATTERY WARNING

flammable liquid or gas.

cause it to explode.

norm al household waste.

1.The lithium battery is built into this product. It must not be dismantled, impacted or exposed to fire.

2.The battery is subjected to extremely low air pressure conditions that may result in an explosion or leakage of

3.Please do not put the battery in a high-temperature environment or expose it to the sun; doing so could

4.Please do not continue to use this product if the battery appears to be swollen.

5.Please dispose of the battery in accordance with local laws and regulations. Do not dispose of the battery as

6.Please do not attempt to repair, disassemble , modify or replace the battery.

7.Please do not place pressure on or pierce the battery with hard objects. Dam aging the battery may

cause battery leakage, overheating or fires.

4

PRODUCT INTRODUCTION

WHAT’S INCLUDED

ROVE

Charging Base x 1

Adapter x 1

Left Side Brush x 1

Right Side Brush x 1

HEPA Filter x 1 + Sponge Foam Filter x 1

600ml Dust Box x 1

Cleaning Brush x 1

Remote Controller x 1

5

PRODUCT INTRODUCTION

Robot Vacuum

Filter Cover

Dust Bin Release Button

Charging Base

Detection Sensor

Obstacle Detection

Sensor

Right Side Brush

Bumper

Sensor

6

ROVE

TOF Wall Sensor

Cliff Sensor

Charging Contact

Omnidirectional

Wheel

Left Side Brush

Primary Wheel

Main Brush

Main Brush Cove

Buckle

PRODUCT INTRODUCTION

ROVE

Robot Vacuum

On/Off/Clean/Pause Button

Indicator Light

• Press once to start/pause

cleaning

• Press and hold for 3 seconds to

turn the device on/off

• When an error occurs, press and

hold for 15 seconds to force

shutdown

Recharge/Partial Clean/Pause Button

• Press to recharge/pause

• Press and hold for 3 seconds to start partial

cleaning

• Blue: Connected to Wi-Fi

• Orange: Not connected to Wi-Fi

• Red: Error or low battery

Reset Wi-Fi

• Press and hold both buttons for 3 seconds

Charging Base

Charging Base

C ompar tment

Charging Base

Cover

Power Indicator Light

Power Connector

Cable Reel

Recharging

Base Signal

Emitter

Charging Base

Power Pins

7

ROVE SETUP

1. Connect the adaptor power cable with the charging base, a n d

then p l a c e any excess c a b l e into the c h a rg i n g b a s e ’ s i n n e r

compartment.

3. Install the Side Brushes

Align the left and right brushes with the corresponding

markings on the bottom cover of the device. Press side

brushes down until they click.

ROVE

2. Place the charging b a s e against the wall on a flat surface.

Then connect the base to a power supply.

Don’t place charging base where it iwill be directly exposed to sunlight.

4. Power On a n d Charging

Press and hold the

until the indicator light turns on, and then place the device

on the charging base.

button to turn on the device. Wait

Note:

Ensure that the charging base has at least 0.5 m of free space on

both sides, and 1.5 m of free space in front of it.

During installation, keep the power cable off the ground. When the

power cable is on the ground, it may be dragged by the robot, which

will cause the charging base to power off.

The charging indicator light will remain on as long as the charging

base has power.

Note: This device cannot start if it does not have enough power. Place

the device on the charging base, and it will automatically turn on

when it has enough power. The device can work normally only

when the battery is ≥20% charged. As shown in the figure above,

the front of the device should face the charging base so that the

charging contact of the robot is touching the wireless power

receiver. The distance between the front of the device and the

charging base should be around 2 cm.

8

USAGE INSTRUCTION

ON/OFF BUTTON

Press a nd hold the button for 3 seconds. The indicator should light

up blue to indicate that the device is turned on.

Under abnormal condition, press and hold the button for 15 seconds to

force the device to shutdown immediately.

Note: The device cannot be turned off while charging in the charging base.

CLEAN/ PAUSE

Once the device has turned on, press the button on the robot or use the mobile a p p

to start the cleaning process.

(Press any key during cleaning to pause cleaning)

Note:

• ROVE robot vacuum CANNOT be used to cleanup liquids.

• If the battery level is lower than 20%, the device will not be able to clean. Please charge

the device before cleaning.

• If the battery level falls below 20% during the cleaning process, the device will automatically

return to the charging base to recharge. Once the battery has been charged to 80%, the

device will attempt to resume its work.

• Pickup all cables (including the power cable of the charging base) from the floor before

It ensures the device does not cause any power outages / object damage by

use.

dragging cables.

CHARGING

Automatic Trigger Charging : When cleaning is completed, the device will return to the

charging base automatically.

Manual Trigger Charging : While the device is paused, press the key once or use

the mobile a p p to trigger the recharging process.

Note: If the device cannot find the charging base, it will return to its starting position.

Users must manually place the device on the charging base.

9

ROVE

START CLEANUP MODE

Press the ON/OFF button to start cleanup. Once the cleaning process has started, it cleans in a

S-shaped cleaning route to cover the whole area efficiently and thoroughly.

Once the cleaning process is completed, the device will automatically return to the

charging base.

Cleaned Area

Planned cleaning Area

Note:

Do not move the device casually during cleaning operation. Once moved, please

place the vacuum at its approximate original location. Once the vacuum has

restarted, it will attempt to reposition itself. If positioning is successful, the

vacuum will resume its planned cleaning path. If positioning fails, it will abandon

previous tasks and rebuild a new map to restart the cleaning process. Under this

situation, the device may not be able to recharge automatically.

USAGE INSTRUCTION

SPOT CLEANING MODE

Users can select the desired area on the app to deep clean it. The

vacuum will automatically drive through the area and s tart s pot

cleaning in a 1.5 m x 1.5 m area.

1.5 m

ROVE

EDGE CLEANING MODE

Users can select edge cleaning mode on the app or remote control to deep

clean an edge of a room. The vacuum will automatically drive along

the edge and s tart to edg e clean for 2 cycles/20 mins. Once edge

cleaning has been completed, the robot will go back to the

charging base automatically.

1.5 m

SCHEDULED CLEANING

Users can use the a p p to set scheduled cleaning times. The device

will start cleaning based on the set times. The device will return to the

charging base once completed.

DND MODE

Users can select DND MODE in the app so the device can clean the

floor without any voice command. Available timing of DND mode can be

set / modified through the app.

Wi-Fi RESET

If the cell phone cannot be connected to the robot vacuum due to change of

router configuration / password or for any other reasons, please reset the Wi-

Fi. Press and hold the key and key simultaneously for 3 seconds. “Wi-Fi

has been reset” voice command will be read, and the indicator light will turn purple

and flick slowly.

SUCTION POWER LEVEL

The a p p a l l o w s users to select up to 3 different suction levels:

Gentle, Normal or Strong. The vacuum’s default suction power level

is Normal.

10

USAGE INSTRUCTION

Remote Control

ROVE

Remote Control Batteries

Auto Cleaning

Start / Pause

Go Forward

Turn Left

Suction Power

Level Select

DND/Silent Mode

Edge Cleaning

Mode

Go Back to

Charging Base

Turn Right

Call Robot

Adjustment of

W ater Flow (O p t i o n a l

F u n ct i o n f o r a d d i n g Mo p

W a t e r T a n k d e vi ce )

Spot Cleaning

Mode

11

2. Insert two AAA batteries into the

battery compartment as shown in the

diagram above.

ROUTINE MAINTENANECE

Main Brush

Side Brush

ROVE

1. Flip over the device. Press the buckle on the main brush cover to

take out the main brush.

2. Use the cleaning brush to remove dust & debris which may have

been stuck in the main brush cavity and main brush body.

3. Reinstall the main brush, then the main brush cover. Once the

brush cover has been securely installed, there will be a click

sound.

1. Flip over the device and pull out the side brushes vertically.

2. Reinstall the brushes after removing any trapped debris and dirt.

3. Align the left and right brushes with the corresponding markings

( L/R )on the bottom cover, and then press down to install.

Note: It is recommended to replace the side brushes once

every 3 to 6 months to ensure optimal performance.

R(Right Brush)

L(Left Brush)

Buckle

( Main Brush Cover )

Main Brush

Robot Vacuum

12

ROUTINE MAINTENANECE

Dust Bin

1. Press and hold the dust bin release button, then pull

out the dust bin as shown below.

ROVE

Filters

and HEPA Filter.

dry completely.

1. After a long period of use, remove the Net Filter, Sponge Foam Filter

2. Rinse the removed filters and dust bin under a tap.

3. After rinsing , shake off water drops. Let the filters and dust bin air

4. After thoroughly drying, reinstall the filters in the following order: Net

Filter > Sponge Foam Filter > HEPA Filter (shown in the diagram below).

Dust Bin Release

Button

2. Open the dust bin and empty the dirt into the

trashcan. Once cleaned, close the dust bin

cover and then slide it in vacuum body.

Net Filter

Dust Bin Release

Button

Filter Cover

Sponge Foam

Filter

HEPA Filter

Note:

• Rinse the filters with clean water only. Do not a d d any

detergents.

• Do not use a brush or your fingers to clean the filters.

• Allow the filters to dry thoroughly for at least 24 hours.

• It is recommended to replace the filters every 3-6 months.

13

ROUTINE MAINTENANECE

Battery

• The vacuum robot is equipped with a high-performance lithium-ion

battery. To ensure optimal battery performance, keep the device

charged.

• If you do not intend to use the device for a long period of time, turn it

off and store it in a safe place. Charge the device at least once every

3 months in order to prevent damage to the battery due to over-

discharge.

ROVE

Sensors (Regular Clean)

Use a soft, dry cloth to wipe all the sensors on the device, including the

following:

1. The TOF Wall Sensor on the right of the vacuum

2. The Cliff Sensor on the bottom of the vacuum

3. The Obstacle Detection Sensor on the front of the vacuum

4. The Charging Contact Plate on the bottom of the vacuum and

power charging pins on the charging base ( WARNING: Please

turn off the power before cleaning)

5. The Charging Base Signal Emission Window

Cliff Sensor

Charging Contact

TOF Wall Sensort

14

PRODUCT INFORMATION

Vacuum Robot

ROVE

Product Name

Rove G2800 Gyroscope Navigation Robot Vacuum Cleaner

Model Number

G2800

Dimensions

350 x 350 x 80 mm

2600mAh Lithium Battery

Weight

Battery

Input Voltage

Rated Power

2.95 kg

14.4V

25W

Charging Base

Dimensions

160 x143 x 80 mm

Rated Power

Rated Output

24W

24W

15

TROUBLESHOOTING GUIDE

ROVE

ERROR CODE

Solution

Error 1: Dust bin removed, please check and restart

The device was started without a dust bin. Reattach the dust bin

and start the device again .

Error 2: Clean the bottom sensor and restart in new

position.

position.

Error 4: Clean the right-side sensor and restart in new

The cliff sensor has been obstructed or placed on non-level

ground. Wipe the window of the cliff sensor with a soft, dry cloth

or move the device to level ground, then restart the device.

Wipe the front obstacle detection sensor with a soft, dry cloth

The TOF wall sensor is dirty or has become obstructed. Wipe the

TOF wall sensor with a soft, dry cloth.

Error 3: Clean the front sensor and restart in new position. The front obstacle detection sensor is dirty or has been blocked.

Error 5: Bumper may be stuck. Please check.

The edge or bumper sensor is stuck. Move the front bumper left

and right to ensure there’s no jam.

Error 6: Main wheel may be stuck. Please check.

The driving wheel is stuck. Check the primary wheel and remove

any foreign objects.

Error 7: Brush bar may be stuck. Please check.

The main brush is stuck. Check the main brush and remove any

foreign objects.

Error 8: Side brush may be stuck. Please check.

The side brush is stuck. Check the side brush and remove any

foreign objects.

16

TROUBLESHOOTING GUIDE

ROVE

ERROR CODE

SOLUTION

Error 9: Error, shutting down.

Please power off and restart the machine. In cases of repeated failure, please

arrange maintenance for the device.

Error 10: Something went wrong, please restart.

Please check the robot’s status and restart it.

Error 11: Please restart in new position.

Please move the robot to a flat surface and restart cleaning.

Error 12: Robot blocked. Restart in new position. Move the device to a non blocked area, then restart cleaning.

Error 13: Robot inclined, restart in level surface

Move the device to a level surface, then restart.

Error 14: Charge station not found.

If the device says that the charging base is not found. Please check the

charging base indicator light is on or move the device back to the

charging base.

Error 15: Battery low.

Place the product on the charging base.

Error 16: Remove from charge station to power

off.

The product cannot shut down when device is on the charging base. Move

the product away from the charging base, and then press and hold the

power button for device shut down .

17

COMMON PROBLEMS

Problem Type

Solution

ROVE

The battery is low. P la ce the device on the charging b a s e a n d align its charging contact onto the charging base power charging

pins. The device should automatically turn on. If the device is out of power, it m a y take some time to turn on.

The ambient temperature e x ce e ds the normal operating ra ng e of 32- 104° F . Only use this product in an environment

which is under normal operating ra ng e of 32- 104° F .

Remove the device a n d che ck whether the charging b a s e indicator light is on or not. Ensure that both the charging b a s e power

charging pins are well connected with the vacuum robot device charging contact plate.

The side brush may block the connection between the charging contact plate and charging base power charging pins. Move the side

brush to ensure there’s no blockage. C le a n the charging contacts on both the charging pins and device contact plate.

The product is too far a w a y from the charging base. Move it closer a n d try a g a in.

Abnormal noise during operation

Foreign objects may be trapped in the primary brush, side brushes, or wheels. Turn off the product a n d cle a r t he fore ig n

obj e ct s, then restart device.

Reduced cleaning performance or dust

blockage from device

• The dust bin is full a n d ne e ds to b e cleaned.

• The filter is b l o c k e d a n d ne e ds to b e cle a ne d or replaced.

• The main brush is stuck with a foreign object a n d ne e ds to b e cleaned.

• Weak Wi-Fi signal. Make sure the product is in an a re a with g o o d Wi-Fi signal coverage.

• Wi-Fi connection error ha s occurred. Download the latest version of the app and r eset the Wi-Fi connection. Try a g a in.

• Incorrect Wi- Fi password.

• The router is running on a 5G Hz network. The router needs to setup a 2.4 GHz network. This device only supports Wi-Fi connection

with 2.4GHz networks.

•

When the product is on the charging base, it will consume a m i n i m u m amount of power to optimize battery performance.

•

•

•

•

•

•

C a nnot b e started

C a nnot b e cha rg e d

C a nnot g o b a c k t o

C h a r g i n g B a s e

Cannot conne ct to Wi-Fi

Consuming power while

device is placed on the

charging b a s e

18

ROVE

WARRANTY – 1 YEAR LIMITED WARRANTY

The 1-Year Limited Warranty applies to purchases made from authorized retailers of WiiRobot Co Limited (ROVE).

Warranty coverage applies to the original owner and to the original product only and is

not transferable.

ROVE warrants that the unit shall be free from defects in material and workmanship for a period of 1 year

from the date of purchase when it is used under normal household conditions and maintained according to the

requirements outlined in this instruction manual, subject to the following conditions and exclusions.

What is covered in my warranty?

1. The original unit and/or non-wearable components deemed defective, in ROVE ’s sole discretion,

will be repaired or replaced for up to 1 year from the original purchase date.

2. In the rare event that a replacement unit is issued, the warranty coverage ends six months following the

receipt date of the replacement unit or the remainder of the existing warranty, whichever is greater. If

the unit is replaced, ROVE reserves the right to replace the unit with one of equal or greater value.

What is not covered in my warranty?

Our Customer Service/Product Specialists are available to provide all the warranty service options

available to you, including the possibility of upgrading to our VIP Warranty Service Options for select

product categories.

1. Normal wear and tear of wearable parts such as foam filters, HEPA filters, pads etc., which require

regular maintenance and/or replacement to ensure the proper functioning of your unit are not covered

by this warranty.

2. Any unit that has been tampered with or used for commercial purposes.

3. WiiRobot (ROVE) will cover the cost for the customer to send in the unit to us for repair or replacement.

4. Damage caused by misuse, abuse, or negligent handling, or damage due to mishandling in transit.

5. Consequential and incidental damages.

6. Defects caused by or resulting from damages from shipping or from repairs, service or alteration to the

product or any of its parts which have been performed by a repair person not authorized by ROVE.

7. Products purchased, used or operated outside of North America.

Problems with your unit/How to get service

If your appliance fails to operate properly while in use under normal household conditions within the

warranty period, please send us email ing.support@beaninformationlogistics.com for

product care/maintenance self-help. Our Customer Service and product specialists are also available

at 1- 888-737-9984 to assist with product support and warranty service options.

How to initiate a warranty claim

You can call 1- 888-737-9984 to have a Customer Service specialist assist you. Please note you must call

1- 888-737-9984 to initiate a warranty claim. Return and Packing Instruction information will be provided at

that time.

19

ROVE

FCC Statement

§ 15.19 Labelling requirements.

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may

cause undesired operation.

§ 15.21 Information to user.

Any Changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

§ 15.105 Information to the user.

Note: This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

*This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

20

WARRANTY CARD

IMPORTANT INFORMATION

Support

Toll-free Customer Support: 888-737-9984 Hours of Operation: Monday-Friday

E-mail support: ing.support@beaninformationlogistics.com

8:30AM – 3:30PM PST (closed holidays)

Safety & Handling

Fire

Hazard

Warning

Use of an AC Adapter / Charger other than the one supplied with this product may

result in overheating the battery, damaging the product and potentially becoming a fire

hazard. WiiRobot Co.,Ltd. is not responsible for any damages caused by use of an

AC Adapter / Charger.

Battery: The battery used in the Vacuum Robot is Lithium-Ion. Lithium-Ion batteries should be properly

disposed of when damaged or disposed.

`

© 2021 WiiRobot Co.,Ltd.

Printed in China

WARRANTY

Products: ROVE G2800

Warranty Term: WIIROBOT CO. LTD (ROVE)warrants this unit against defects in material and workmanship for a period of one (1) year

from the original date of purchase.

Parts and Labor: If the unit is found to be defective during this warranty period, WIIROBOT CO. LTD will repair the unit using new or

“refurbished” parts or replace it with a new or “refurbished” product. “Refurbished” part or “refurbished” product means a part or product that

has been restored to its original specification. Repair of the unit or replacement of the unit is at the sole discretion of WIIROBOT CO. LTD.

Labor charges will be covered by WIIROBOT CO. LTD within the warranty period. Repaired or replaced parts or products will be warranted

for the remainder of the original warranty period, or ninety (90) days, whichever is longer.

Limitations: This Limited Warranty covers defects in material and workmanship which occur during normal use. It does not cover issues

caused by acts of God or occurrences of nature, misuse, abuse, accidental damage, damage in transit, cosmetic defects, contact with

foreign substances causing damage, or damage caused by extreme temperature. This limited warranty also does not cover defects caused

by unauthorized modifications or calibrations, reception issues, the intrusion of foreign elements such as computer or internet viruses,

damage caused by installation, or the use of parts. Any charging device or power supply not supplied by ROVE for its model is considered

unauthorized. Any damage caused by using this product due either to the unauthorized accessory, to the ROVE product or to any item,

belonging, person, animal or other entity is not the responsibility of WIIROBOT CO. LTD. Further, any damage to the ROVE product caused

by using an unauthorized accessory is not covered under this warranty. Proof of purchase or a receipt showing date of original purchase

must be presented for this warranty to be honored.

THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE LISTED IN THIS DOCUMENT. ANY IMPLIED WARRANTIES SHALL

BE LIMITED IN DURATION AS OUTLINED ABOVE, INCLUDING IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE. ALL IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE FOR COMMERCIAL PURCHASERS ARE EXCLUDED. BEAN INFORMATION TECHNOLOGY SHALL

NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED

WARRANTY ON THIS PRODUCT. THE TOTAL LIABILITY TO BEAN INFORMATION TECHNOLOGY FOR ANY AND ALL LOSSES

AND DAMAGES DUE TO ANY CAUSE WHATSOEVER, SHALL NOT EXCEED THE PURCHASE PRICE OF THIS PRODUCT. SOME

STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT

APPLY TO YOU.

This warranty gives you specific legal rights, and you may also have other rights which vary from State to State. Please consult applicable

state laws for a determination of your rights. There shall be no extensions, modifications or additions to this warranty authorized by any agent

or employee of WIIROBOT CO. LTD or by any of its distributors or resellers.

Obtaining Warranty Service: Please contact BEAN INFORMATION TECHNOLOGY Customer Service (as outlined below) for detailed

instructions to obtain warranty service.

Warranty Service Inquiries:

E-mail support: ing.support@beaninformationlogistics.com

Toll-free Customer Support: 888-737-9984

Hours of operation:

Monday-Friday 8:30AM – 3:30PM PST (closed holidays)

Warranty service is only available from an Authorized WIIROBOT CO. LTD Warranty Service Center. The nearest Authorized Warranty

Service Center can be determined by contacting WIIROBOT CO. LTD Customer Service. Products requiring warranty service must be

shipped to the WIIROBOT CO. LTD Authorized Warranty Service Center freight prepaid, in original packaging or packaging with the same

degree of protection as original packaging. WIIROBOT CO. LTD, or an Authorized WIIROBOT CO. LTD Warranty Service Center will ship

your product back to you freight prepaid upon completion of warranty service. All products submitted for warranty service must contain a

copy of the original dated receipt and must have the factory applied serial number affixed to the product. WIIROBOT CO. LTD is not

responsible for damage incurred by freight.

Prior to delivering or shipping any products for warranty service you must obtain a Warranty Service Authorization from

WIIROBOT CO. LTD Customer Service.

This warranty is valid for covered product sales in the United States, Canada and Puerto Rico only, and covers units which are used only in

the United States, Canada and Puerto Rico.

MS2WCS ver. 20.02w



 

 

 

 

 

 

 

 

 

 

主机铭牌

Rove G2800 Gyroscope Navigation

Robot Vacuum Cleaner

G2800

2AZ7PG2800

Guangdong WiiRobot Co.,Ltd

99*45.5mm, 75#消银龙+15#哑膜+黑色底白色字

FCC ID:2AZ7PG2800

G2800(J300)

主机铭牌

N10.J300.079

2021.06.21



 

 

C5266091_X10_Ed.2

Guangdong WiiRobot Co., Ltd.

Office of Engineering Technology

Federal Communications Commission

7435 Oakland Mills Road

Columbia, MD 21046 Date: 7/19/2021

Subject: Request for Confidentiality

FCC ID: 2AZ7PG2800

To Whom It May Concern,

Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules

(47CFR0.457, 0.459), we are requesting the Commission to withhold the following

attachment(s) as confidential document from public disclosure.

Exhibits

ID Label/Location

Attestation Statement

External Photos

Block Diagram

Schematics

Test Report

Test Setup Photos

User’s Manual

Internal Photos

Parts List / Tune Up

RF Exposure Info

Operational Description

Cover Letter(s)

SDR Software / Security Info

Long-Term

Confidentiality

No

No

No

☒

☒

No

No

☐ NOTE 1

☐ NOTE 1

☒

No

☒

No

☐

Short-Term

Confidentiality NOTE 2

No

No

☐

☐

☐

No

☐

☐

☐

☐

No

☐

No

No

NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of

KDB 726920, use last in force)

NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant.

Above mentioned document contains detailed system and equipment description are

considered as proprietary information in operation of the equipment. The public

disclosure of above documents might be harmful to our company and would give

competitor an unfair advantage in the market.

In case of short-term Confidentiality, the applicant requests the exhibits selected above

are withheld from public view for a period of ______ days from the date of the Grant of

Equipment Authorization and prior to marketing.

It is our understanding that all measurement test reports, FCC ID label format and

correspondent during certification review process cannot be granted as confidential

documents and those information will be available for public review once the grant of

equipment authorization is issued.

1/1



C5266091_X10_Ed.2

Sincerely,

Signature:

Name: Autumn Su

Title: QA

1/1



 

 

 

 

 

 

Letter of Authorization C5266091_X8_Ed.1 Company: Guangdong WiiRobot Co., Ltd. Address: Room 401, Building 1, No.11 Yinghe 1st Street, Yaoshan, Xiegang Town, Dongguan City, Guangdong Province Product Name: Rove G2800 Gyroscope Navigation Robot Vacuum Cleaner Model Number: G2800, G2800-BK, G2800-GY, G2810-GY, G2810 FCC Identifier: 2AZ7PG2800 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Autumn Su Date: 7/13/2021 Title: QA Signature of applicant:

1/1