FCC ID: XHT-1012348 Toy RC Speed Bumper Road Rage

RC ROAD RAGE SPEED BUMPERS 6+

Carefully remove items from package. ii OPERATING INSTR UCTI ONS iiii Each vehicle requires 3 AAA 1.5V batteries (not included). Each remote control requires 2 AAA 1.5V batteries (not included). When changing batteries, adult supervision is required. Use alkaline batteries for best performance. Locate the battery compartment on the bottom of each vehicle, and the handle of each remote. Loosen the screws and remove the battery doors. Insert AAA batteries while observing the correct polarity in each compartment. Replace the battery doors and tighten the screws. iiiiii Switch both car and remote buttons to ON position. For best result use the car on hard surfaces such as wood or tile. Led Power Indicator Battery Cover On/Off Switch On/Off Switch Ejecting Rider SAFETY PRECAUTIONS Attaching Rider 1. Insert the white peg (located on bottom of rider) into the hole on the vehicles seat. 2. Gently press down until the rider clicks into place. HOLE SIDE BUMPER There are bumpers located on the sides of each vehicle (one on each side). The object of the game is to knock the opposing rider off of its vehicle by making contact with one of the two bumpers. NOTE: Bumpers can also be activated by walls and other objects. Do not operate during thunderstorms or rain. Avoid water, sand and snow when operating car. Do not submerge car or controller in water. Never operate your car on the street or highway. Never operate your car in a conned or crowded area, and do not use people or animals as obstacles. Do not run your car into furniture, objects or hard surface, as this will cause damage to both the objects and your car. Keep ngers, hair and loose clothing away from the tires. gears and motor while the car is switched to ON. Do not leave car or transmitter near source of heat or under direct sunlight for long periods of time. Do not leave car or transmitter outside overnight. Dampness is harmful to interior components Remove all batteries when not in use to avoid accidental operation Adult supervision is recommended when operating this car. BATTERY WARNING:

Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries. Insert batteries using the correct polarity. Do not short-circuit the supply terminal. Remove batteries when not in use. Recycle or dispose of exhausted batteries according to federal, state, and local laws. Do not dispose of batteries in a re - they may leak or explode. Only use manufacture specied battery(ies), charger(s) and/or adapter, if applicable, specied by the manufacturer. Always use, replace, and recharge (if applicable) batteries under adult supervision. Keep these instructions for future reference. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Warning: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. KEEP THIS INSTRUCTION MANUAL AS IT CONTAINS IMPORTANT INFORMATION FOR FUTURE REFERENCE. Due to continuous product improvements, the pictures on this manual may differ slightly from the actual product. The artwork and design of this manual are protected by US copyright law and may not be reproduced, distributed, displaced, published or used for any purpose without prior written permission. Altering, removing or reproducing any of the trademark or copyright notices on this package is not permitted. 2020 Sharper Image. Sharper Image name and logo are registered trademarks. All rights reserved. 2020 MerchSource, LLC. Irvine, CA 92618. All rights reserved. Distributed by MerchSource, LLC, Irvine, CA 92618. Model NO.: 1009537 Printed in China FOR TECHNICAL SUPPORT, PLEASE CALL 1-800-374-2744 Reverse Forward Left Turn Right Turn

Label Artwork and Location FCC ID: XHT-1012348 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. SIZE: 55mm (W) x 20mm (H)

Guangdong Yinrun Industry Co.,Ltd. Attention: Certification reviewer RE:

Request for Confidentiality FCC ID: XHT-1012348 To Whom It May Concern:

Permanent Confidentiality [Complete this section if permanent confidentiality is requested]

Request to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential:

[Select one or more of items below, as appropriate, and delete unselected parts]

Schematics Block Diagrams Operational Description Internal Photos (see note) Users Manual (see note) Note 1: Internal Photos may be held confidential 1) if the circuit board or internal components are not accessible to users. For example, it is acceptable if the circuit board is enclosed in epoxy. 2) Also, it is acceptable if the device is not accessible to the public, for example, a device mounted on the top of a large tower (or in a fenced enclosure) such that it is only serviceable by professional designated technicians under a Non-Disclosure Agreement (NDA). All sales for these devices must be under a NDA restricting the disclosure of the propriety information, including internal photos. Users Manual may be held confidential only when the manual contains proprietary technical information intended for professional technicians obligated under a NDA. All sales and distribution of the users manual must be under a NDA that restricts the disclosure of the information. In the application cover letter requesting permanent confidentiality the following additional description and the NDA exhibit is required:

1. Describe in detail how internal photos and/or users manual information are controlled to prevent them from becoming public or disclosed to unauthorized persons. 2. Describe how public access is restricted for products serviceable by professional designated 3. A statement that all sales of the non-consumer device will be under a NDA to include third party sales and that the final user of the device is subject to the NDA. 4. Provide an example of the NDA between the grantee and a purchaser. The request for confidentiality technicians. must Note 2: For scanning receiver, the schematics, block diagrams, operational description, tune-up procedure, parts list and internal photos are always held permanently confidential. Rationale for request for confidentiality:

We have invested considerable time and materials in research and development to produce the referenced product. Permanent confidentiality: Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us. If you have questions or need further information, please contact the undersigned. Sincerely, _________________ CYRUS YANG GENERAL MANAGER 2020-7-7

Guangdong Yinrun Industry Co.,Ltd. 2020-7-7 Federal Communications Commission 445 12th Street SW Washington, DC 20554 Subject:

Limited Agency Agreement Guangdong Yinrun Industry Co.,Ltd. FCC ID: XHT-1012348 To Whom It May Concern:

We, Guangdong Yinrun Industry Co.,Ltd., hereby authorized Intertek Testing Services to act as our Agent for the purpose of preparing application for FCC ID number XHT-1012348 under all applicable parts of the FCC rules and regulations. The effective date of this limited agency agreement is 2020-7-7. The Limited Agency Agreement expires on 2021-7-7, unless sooner terminated or extended by written notice to Intertek Testing Services and the Federal Communications Commission. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. The applicant is not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 U.S.C. 862, and no party to the application is subject to a denial of federal benefits pursuant to that section. If you have any questions or comments, please do not hesitate to contact me. Sincerely,

[Signature]

CYRUS YANG GENERAL MANAGER