FCC ID: 2AKAR-UHFUR502SF UHF Reader

UHFS Pro/UHFlO Pro Reader User Manual Copyright2020 ZKTECO CO., LTD. All rights reserved. Without the prior written consent of ZKTeco, no portion of this manual can be copied or forwarded in any way or form. All parts of this manual belong to ZKTeco and its subsidiaries (hereinafter the "Company" or "ZKTeco"). ZKTa: is a registered trademark of ZKTeco. Other trademarks involved in this manual are owned by their respective owners. Trademark Disclaimer This manual contains information on the operation and maintenance of the ZKTeco equipment. The copyright in all the documents, drawings, etc. in relation to the ZKTeco supplied equipment vests in and is the property of ZKTeco. The contents hereof should not be used or shared by the receiver with any third party without express written permission of ZKTeco. The contents of this manual must be read as a whole before starting the operation and maintenance of the supplied equipment. If any of the content(s) of the manual seems unclear or incomplete, please contact ZKTeco before starting the operation and maintenance of the said equipment. It is an essential pre-requisite for the satisfactory operation and maintenance that the operating and maintenance personnel are fully familiar with the design and that the said personnel have received thorough training in operating and maintaining the machine/unit/equipment. It is further essential for the safe operation of the machine/unit/equipment that personnel has read, understood and followed the safety instructions contained in the manual. In case of any conflict between terms and conditions of this manual and the Page 11 Copyright2020ZKTECO CO.,LTD. Allrightsreserved. UHFS Pro/UHFlO Pro Reader User Manual contract specifications, drawings, instruction sheets or any other contract-

related documents, the contract conditions/documents shall prevail. The contract specific conditions/documents shall apply in priority. ZKTeco offers no warranty, guarantee or representation regarding the completeness of any information contained in this manual or any of the amendments made thereto. ZKTeco does not extend the warranty of any kind, including, without limitation, any warranty of design, merchantability or fitness for a particular purpose. ZKTeco does not assume responsibility for any errors or omissions in the information or documents which are referenced by or linked to this manual. The entire risk as to the results and performance obtained from using the information is assumed by the user. ZKTeco in no event shall be liable to the user or any third party for any incidental, consequential, indirect, special, or exemplary damages, including, without limitation, loss of business, loss of profits, business interruption, loss of business information or any pecuniary loss, arising out of, in connection with, or relating to the use of the information contained in or referenced by this manual, even if ZKTeco has been advised of the possibility of such damages. This manual and the information contained therein may include technical, other inaccuracies or typographical errors. ZKTeco periodically changes the information herein which will be incorporated into new additions/amendments to the manual. ZKTeco reserves the right to add, delete, amend or modify the information contained in the manual from time to time in the form of circulars, letters, notes, etc. for better operation and safety of the machine/unit/equipment.The said additions or amendments are meant for improvement /better operations of the machine/unit/equipment and such amendments shall not give any right to claim any compensation or Page 12 Copyright2020ZKTECO CO.,LTD. Allrightsreserved. UHFS Pro/UHFlO Pro Reader User Manual damages under any circumstances. ZKTeco shall in no way be responsible (i) in case the machine/unit/equipment malfunctions due to any non-compliance of the instructions contained in this manual (ii) in case of operation of the machine/unit/equipment beyond the rate limits (iii) in case ofoperation of the machine and equipment in conditions different from the prescribed conditions of the manual. The product will be updated from time to time without prior notice. The latest operation procedures and relevant documents are available on http://www.zkteco .com If there is any issue related to the product, please contact us. ZKTeco Headquarters Address ZKTeco Industrial Park, No. 26, 188 Industrial Road, Tangxia Town, Dongguan, China. Phone

+86 769 - 82109991 Fax

+86 755 - 89602394 For business related queries, please write to us at: sal es@zkte co.com. To know more about our global branches, visit www.zkteco.com. Page 13 Copyright2020ZKTECO CO.,LTD. Allrightsreserved. UHFS Pro/UHFlO Pro Reader User Manual About the Company ZKTeco is one of the world's largest manufacturer of RFID and Biometric

(Fingerprint, Facial, Finger-vein) readers. Product offerings include Access Control readers and panels, Near & Far-range Facial Recognition Cameras, Elevator/floor access controllers, Turnstiles, License Plate Recognition (LPR) gate controllers and Consumer products including battery-operated fingerprint and face-reader Door Locks. Our security solutions are multi-

lingual and localized in over 18 different languages. At the ZKTeco state-of-

the-art 700,000 square foot 1509001-certified manufacturing facility, we control manufacturing, product design, component assembly, and logistics/shipping,all under one roof. The founders of ZKTeco have been determined for independent research and development of biometric verification procedures and the productization of biometric verification SDK, which was initially widely applied in PC security and identity authentication fields. With the continuous enhancement of the development and plenty of market applications, the team has gradually constructed an identity authentication ecosystem and smart security ecosystem, which are based on biometric verification techniques. With years of experience in the industrialization of biometric verifications, ZKTeco was officially established in 2007 and now has been one of the globally leading enterprises in the biometric verification industry owning various patents and being selected as the National High-tech Enterprise for 6 consecutive years. Its products are protected by intellectual property rights. About the Manual This manual introduces the operations of UHFS Pro/UHFl O Pro Reader. All figures displayed are for illustration purposes only. Figures in this manual may not be exactly consistent with the actual products. Page 14 Copyright2020ZKTECO CO.,LTD.Allrightsreserved. UHFS Pro/UHFlO Pro Reader User Manual Table of Contents 1 2 3 4 5 6 7 OVERVIEW...................................................................................................... 6 SIDE VIEW &WIRING.....................................................................................7 SPECIFICATIONS.......................................................................................... 8 DIMENSIONS.................................................................................................. 9 SOFTWARE CONFIGURATION................................................................10 5.1 INTRODUCTION..........................................................................................................10 5.1.1 5.1.2 5.1.3 MAIN INTERFACE..............................................................................................10 RS485 SETTING INTERFACE..........................................................................14 SYSTEM SETTINGS..........................................................................................16 ACCESS CONTROLLER CONNECTION................................................ 18 INSTALLATION PROCEDURE..................................................................19 8 WIRING DIAGRAM....................................................................................... 22 9 FAQ................................................................................................................. 22 Page IS Copyright2020 ZKTECO CO., LTD. All rights reserved. 928M UHFS Pro/UHFlO Pro Reader User Manual 2 Side View & Wiring Mounting Bracket 2 3 4 5 6 7 8 9 Black Green White Purple Gray USB Brown Orange Wiegand DO Wiegand D1 Trigger Point GND Connect to PC RS485+

RS485-

Page 17 Copyright2020 ZKTECO CO., LTD. All rights reserved. UHFS Pro/UHFlO Pro Reader User Manual 3 Specifications Reading Distance 2 to 8 meters (Hand-held 10 to 20meters (Hand-

test) held test) Actual scenario test is Actual scenario test is Dimension 308.5*308.5*67.5 mm 445*445*67.5 mm Antenna Gain 9dBi around 4m Weight Power Frequency 1.8kg 1.2 to 4.2 W E: 865MHz to 868MHz around 8m 12dBi 3kg 1.2 to 4.5 W F: 902MHz to 928MHz (supports adjustment) Communication Wiegand; RS485; USB Configuration parameters interface

(Wiegand, RS485 requires one of the two options) Interface Protocol EPC global UHF Class 1 Gen 2 / ISO 18000-6(

Working Mode Read Always (Default) & Read by Trigger Output Power 19dBm to 30dBm Protection Class IP66 Working Voltage DC 9 tolSV Working Temperature and

-20(to 65(,<85%

Temperature and

-20(to 80(,<85%

Humidity Storage Humidity RS485 Communication 115200). The default is 115200 Optional baud rate (9600, 19200, 38400, 57600, Page 18 Copyright2020 ZKTECO CO., LTD. All rights reserved. UHFS Pro/UHFlO Pro Reader User Manual

m

y 4 Dimensions UHFS E/F Pro:

,r : I I UHF 10E/F Pro:

II -;- -I II I l I I II I --:-7 1 Page 19 Copyright2020 ZKTECO CO., LTD. All rights reserved. UHFS Pro/UHFlO Pro Reader User Manual 5 Software Configuration UHF Reader 5.1 Introduction 5.1.1 Main Interface Take the operation of the American standard reader as an example:

:I lr:mii1 11 Ir-II RF Sett ,ng, Powec -

to --

dBm Tag R, a d;ng lntecva l (0 - 25) T,m, ..

, KHz w ;e gan d D" tp ul Sett,ngs 0 Foro,cd Ootpct e loverted Ootpct 0 Read Always M

I Save Cha I d Tag I F aao ry u k I Co,occt Scccmfoll Output T;m, (2 -10) T;m, -

X1 m, I ReadConfi Page 110 Copyright2020ZKTECO CO., LTD. All rights reserved. UHFS Pro/UHFlO Pro Reader User Manual Reader Connection Reader. Click Connect to connect the Reader, and click Disconnect to disconnect the Work Mode Configuration Click Read Always to make the Reader always in the read status. Click Read by Trigger to enable the reader to read only after it is triggered. Connect I Disconnect Work Mode Read Always Read By Trigger Read Time C 1 -255 ):

The RF Settings helps to set the Power and Frequency values. RF Settings FR s e gt t p s re0 l _ dBm q erF 1902000 VI to 906000 v I KHz Page 111 Copyright2020 ZKTECO CO., LTD. All rights reserved. UHFS Pro/UHFlO Pro Reader User Manual Buzzer Select the Buzzer check box to enable the Buzzer. eR ed a n r acidI l r t B[

e rzzu Wiegand Output Setting The Wiegand Output Settings consist of Forward Output and Inverted Output. Click Forward Output to read the card number in the partition in the progressive order, and click Inverted Output to read out the card number in the partition in the reverse order (customers need set). Wiegand Out p Sett ing s not For\l\lard Output I nvert ed Output Start Byte The time of continuous output signal of the reader can be set, and the Output Duration Setting maximum setting time is 1s. Out p Time (2-10) Time

X lOOms Page 112 Copyright2020 ZKTECO CO., LTD. All rights reserved. UHFS Pro/UHFlO Pro Reader User Manual Wiegand Format Setting The default Wiegand format is WG26, and it can be set as WG34, WG42, WGSO, WG58, WG66, WG74, WG82, WG90, WG98. Card Reading Interval Setting You can set the card reading interval to prevent the eated card reading. WG90 WG98 Tag Rea ding I nterval (0-25) r;m. _, rep 7 Page 113 Copyright2020 ZKTECO CO., LTD. All rights reserved. UHFS Pro/UHFlO Pro Reader User Manual 5.1.2 RS485 Setting Interface The controllers supported by default are inbio260 and inbio460. Baud Rate Setting The default Baud rate is 96000 and it can be adjusted as per the requirements. Baudra t e Sett ir. B aud r ate -

Device Address Setting The Device Address Setting is used to distinguish the readers which are installed in different locations. Device Address Add ress-

( 0 - 255 ) Pa g e I 14 Copyright2020 ZKTECO CO., LTD. All rights reserved. UHFS Pro/UHFlO Pro Reader User Manual RS485 Working Mode Select Polling Mode to send a command to search for cards, and the reader will reply to the corresponding data after receiving the card search command. Select Auto Work to read the card and automatically upload the data to the Controller. A"to Wo,k I

[)(]'C RS48 Ourtput Sett ing s Forward Output Invert ed Output OutputLength Start Byte The RS485 Output Settings consist of Forward Output and Inverted Output. Click Forward Output to read the card number in the partition in the progressive order, and click Inverted Output to read out the card number in the partition in the reverse order. Page 115 Copyright2020 ZKTECO CO., LTD. All rights reserved. UHFS Pro/UHFlO Pro Reader User Manual 5.1.3 System Settings LED Light Setting The LED indicator color can be set in the Standby Status and the Read Card Status. There are seven colors to choose. lED Sett ing s Sta ndy Status Read Card Status Iii Led Switch I I mpo rt Sett ing s I I ExportSettings I Set the location of the data import and export. Page 116 Copyright2020 ZKTECO CO., LTD. All rights reserved. UHFS Pro/UHFlO Pro Reader User Manual There are 3 Card Reader output modes namely Wiegand Mode, RS485 mode Card Reader Output and TCP/IP mode. rR e RS4S5 Mode e TC / W Mode e:

Language Settings Right click in the blank area of the Demo interface, a pop-up appears as shown below, click Language Settings to select the language. Lan gu age IEng l i sh I Page 117 Copyright2020 ZKTECO CO., LTD. All rights reserved. UHFS Pro/UHFlO Pro Reader User Manual 6 Access Controller Connection UHF Reade r Page 118 Copyright2020 ZKTECO CO., LTD. All rights reserved. The position of Antenna

-_-- '60 -75

, I Adjust the position hT e b apra ikr.rel g 2 2n m

r

t ------ -

The line of the sight

u>

v

5-

me0 1 Mounting Bracket UHFS Pro/UHFlO Pro Reader User Manual 3. The position of the tag/card in the vehicle must be as follows:

lL ',-; l]

Option A

11

Option C Option B 11 .,. 11 4. The reader detection distance may vary depending onclimatic conditions such as rain, snow or wind...-

,',',,.',, 5. The Reader should be away from any strong magnetic field while working. Page I 20 Copyright2020 ZKTECO CO., LTD. All rights reserved. UHFS Pro/UHFlO Pro Reader User Manual Recommended tags L::....::.. _J UHF1-

Tag1 card UHF Parking Tag Parking lot label Exp lana t ion Operating frequency: 840 to 960MHz Data Storage: 32-bitTID, 64-bit Unique TID, 96-bit EPC, 512-bit User. Supported Protocol: EPC global class 1 Gen2 / 1S018000-6C Product size: 85.6x54.0x0.8mm Operating frequency: 840 to 960MHz Data Storage: 32-bitTID, 64-bit Unique TID, 96-bit EPC, 512-bit User, etc. Support Protocol: EPC global class 1 Gen2 /

1S018000-6C Product size: 1OO.Ox23.2x0.4mm Page I 21 Copyright2020 ZKTECO CO., LTD. All rights reserved. UHFS Pro/UHFlO Pro Reader User Manual

= II [el 1:1i 1 iTi1 RF Sett ,ngs Powec -dBm Readec Conne ct ,on Wmk Mode I I Fl j11 li-

0 Re,d Alw, Fceq -

;!!1!'1!1!11 Tag Rea d ing l nt m a l (0-25) Time_

, to -

KHz w ;ego nd O, tput Sett,ng,

(:) Fo vacd Octpct Inve rted Octpct Output r;me (2-10) r;me-

X 1 00m s I Reed Co I Save C ngn I I Ree d T Facto

'Y ul l I 1-r-mIm1111 Demo Vernon, UHF Demo-UN-V306 Re ecTyoe u,, oc,, pt Rea dec

, mwace Ve " "' UHF_UWRN_V3.06 Check whether there is any interference of the adjacent reader and power station magnetic field near the reader. Check whether the reader is installed correctly and whether the tag is operated correctly. Replace the tag orreader. What can be done if the reader doesn't read the card?

Try the following possibilities:

When the reader is connected to DEMO, you need to click Disconnect so that it could read the card again. Connect the Demo to check whether the manual card reading is normal. If the manual card reading does not respond, there is a problem with the reader. If the manual card reading fails after the factory reset, replace the reader. Determine whether the tag is our product, replace the tag test. Page I 23 Copyright2020 ZKTECO CO., LTD. All rights reserved. UHFS Pro/UHFlO Pro Reader User Manual What to do if the barrier doesn't open after reading the card?

Try the following possibilities:

Short circuit the NO and COM terminals of the reader, check whether the switch is open. If it is not open, check whether the connection between the reader controller port and the barrier port is correct. Check whether the barrier is open when the UP and GND terminals are short circuited. If not, the barrier is faulty. Check whether the tag has registered the information on the software and the data is synchronized to the reader. When swiping the card, pay attention to whether the controller has the sound of relay jumping, and whether the software has the normal door opening record display. If so, check whether the output port of the controller relay signal is connected to the brake in a wrong manner or connected to another output port. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help Changes or modifications not expressly approved by the party responsible for compliance Page I 24 Copyright2020 ZKTECO CO., LTD. All rights reserved. UHFS Pro/UHFlO Pro Reader User Manual could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. RF Exposure Warning Statements:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment shall be installed and operated with minimum distance 20cm between the radiator & body. Page I 25 Copyright2020 ZKTECO CO., LTD. All rights reserved. ZKTeco Industrial Park, No. 26, 188 Industrial Road, Tangxia Town, Dongguan, China. Phone : +86 769- 82109991 Fax

: +86 755 - 89602394 w ww.zkte co.com Copyright 2020 ZKTECO CO., LTD. All Right s Reserved.

Guangdong ZK Radio Electronic Tech Co., Ltd Agent Authorization Company: Guangdong ZK Radio Electronic Tech Co., Ltd Address: 1004 Room, 3 block B, Tian-an-Yun-Gu, Ban Tian Longgang,Shenzhen,China Product Name: UHF Reader Model Number(s): UHF UR502SF, UHF100F, UR500SF, UR500SF-T Product Description: UHF Reader We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature:

Name:

lixue lan Date: 2020-12-04 Company: Guangdong ZK Radio Electronic Tech Co., Ltd

Guangdong ZK Radio Electronic Tech Co., Ltd Dec.04, 2020 Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Subject: Explanation of differences between product types FCC ID : 2AKAR-UHFUR502SF Model Number: UHF UR502SF, UHF100F, UR500SF, UR500SF-T To Whom It May Concern:

We, The Guangdong ZK Radio Electronic Tech Co., Ltd hereby declare that the model : UHF100F, UR500SF, UR500SF-T is identical with the model : UHF UR502SF, except the model name. Except for the different above, no other modification is performed. Sincerely, Signature:

Guangdong ZK Radio Electronic Tech Co., Ltd Contact person: lixue lan

Guangdong ZK Radio Electronic Tech Co., Ltd Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2020-12-02 Subject; Request for Confidentiality FCC ID: 2AKAR-UHFUR502SF To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure External Photos Test Setup Photos Internal Photos User Manual In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

OR For 45 days, pursuant to Public Notice DA 04-1705. For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely Guangdong ZK Radio Electronic Tech Co., Ltd Contact person: lixue lan