FCC ID: 2BBSH-AST2017 Electronic Knob Door Lock

Anland Security Technology Installation and Operation Manual Description:

Model No.:

Features:

Material:

Electronic Knob Door Lock ES0001 Fingerprint and PIN Code Zinc alloy furniture and SUS304 latch Product Standard Referred: ANSI/BHMA A156.25 Thanks for choosing our premium quality product of smart home security with innovative design. Please read this manual carefully before installation and use. For any query please contact us by email customers-ast@anlandst.com. Guangzhou Anland Security Technology (AST) bids to the expert of creating value for customers in security and hardware!

Our Vision Effective contribution on product value, innovation and customer focus Our Mission Become customers reliable partner in innovation Be the expert of creating value for customers in security and hardware Guangzhou Anland ST Co., Ltd 1. PARTS INCLUDED IN THE PACKAGE Tools in need but not included in the package: Phillips screwdriver; Tape measure 2. PRODUCT CONFIGURATION AND INDICATING LIGHT 2.1. A configuration of product and parts description are as below image. 2.2. There are different indicating lights during setting and operating 2.2.1 Add Fingerprint The Fingerprint reader light turns to blue as to indicate the lock is ready to input new Fingerprint, please put your finger on the Fingerprint reader on Exterior Cover Assembly. 2.2.2. Fingerprint identifying or mobile phone APP unlocking Green light: success (the buzzer beeps once, and the Fingerprint reader light flashes green.) Red light: failed (the buzzer beeps twicethe Fingerprint reader light flashes red.) 2.2.3. Low power of batteries When the lock is unlocked with Fingerprint or mobile APP, the buzzer beeps once and Fingerprint reader light flashes green and red. 3. PRODUCT OUTLINE DIMENSIONS 4. CUT-OUT OF DOOR FOR INSTALLATION Please be noted that the Latch backset can be interchangeable (60mm/70mm) 5. INSTALLATION OF LATCH ASSEMBLY AND STRIKE PARTS Set the backset of Latch Assembly to 60mm or 70mm to fit your door hole as above image, then insert the Latch Assembly into the door hole, and drive screw A to fix the Latch Assembly, then install Strike Box and Strike Plate with screw A into the door frame. 6. INSTALLATION OF INTERIOR AND EXTERIOR KNOB MODULES Install Exterior Knob Module (with Touch pad and Fingerprint reader) as above image from inside of your door, and make sure the Spindle and Screw Stems go through the three holes of the Latch. Insert Interior Knob Module by aligning the two stems with the screw holes as above image, connect the cable by inserting the connector into the socket, and drive Screw B to fix Exterior and Interior Knob Modules. 7. IINSTALLING OF BATTERIES (4 EA OF AAA, NON-RECHARGEABLE) Undrive the 2 screws at side face of Interior Knob Module to dismount the Battery Cover Assembly, then insert 4 ea of AAA batteries and drive the screws to fix the Battery Cover Assembly. Important Note: please do not use rechargeable battery, and make sure the pole of batteries at right direction as shown by above image. 8. CHECKING OF FUNCTIONS 8.1. After the Lockset is installed, please check the functions by Internal Snib as below image, to make sure the locks mechanism is working properly. 8.2. Wake up the Touch pad and input the right PIN code (inputting 8 digits and click

# as a confirmation). The keys visible * means delete and # means confirm. Defaulted PIN Code is 012345, it will become invalid once the new PIN Code is set by the APP of mobile which is connected to the Lockset (through Bluetooth). 8.3. Please check above Type-C port for power supply of contingency as above image. 8.4. Press the Set button on the rosette of Interior Module for 8 seconds as above image, the buzzer will beep once and the Fingerprint reader will flash green. The lock will be reset to factory settings, then all the stored data will be wiped and new Fingerprint/PIN code will be required per the process of APP setting. 8.5. Pull the Exterior Cover Assembly of Exterior Module out and insert the back-up key to check locking/unlocking function as above image. 9. INSTALLATION OF APP 9.1. Download / Install the APP by mobile / IPAD Scan the below QR code to download the Tuya Smart APP, or search Tuya Smart in the APP Store (iOS) or Google Play (Android) to install the APP. 9.2. Register an account Register a account and endorse the statements, press Agree and Sign Up on the login screen if no objection as below images. Note: the first one to connect the Lockset by APP will be recognized as Master User. Such record can be removed by resetting the lock by pressing 8 seconds to the Reset Button. Choose the country where the Lockset will be used, enter your Email address to get verification code, set password, select permissions and press Go to APP to finish the registration as below images. 9.3. Connect the Lockset to your APP Turn on the Bluetooth of your mobile phone, keep it close to the Lockset (2~7 meters), then touch the Fingerprint reader to motivate the lock, and press the Add Device on the APP screen. Prior to scanning nearby devices, please turn on the permission as below images of APP. 9.4. Click Add and + to connect the Lockset you want to set up as below images 9.5. Press to rename the Lockset if you want. Now the Lockset is ready for use via APP. 9.6. Control the Lockset via APP Click and drive the key icon from left to right position for unlocking the door as below images. 9.7. Member management and Fingerprints / PIN Code input Select Member Management on the APP screen. To click Me and follow the APP instructions to add Fingerprint (similar to add the PIN Codes). Click + to add more PIN Codes of member. Important Note: proper Fingerprint inputting is critical to access verification, most of the failures of Fingerprint identification are because of improper Fingerprint inputting, please make sure your finger is clean and positioned on Fingerprint reader precisely. 9.8. Create smart scenes Select Smart Scenes on the APP screen, choose the scenes you prefer to set intelligent interactions. 9.9. Setting Select Settings on the APP screen to turn on/off Auto Lock or set the time delay, or turn on/off Do-Not-Disturb. 9.10. Device information setup Click the icon on the top right corner of the APP screen to check and set the relevant information 10. TECHNICAL SPECIFICATION No. Parameter 1 2 3 4 5 6 7 8 9 10 11 12 USB power supply Fingerprints max. PIN Codes max. Low power warning Voltage range Stand-by current Working current Unlocking time Recommended working temperature Door thickness Material Power Specification Type-C / 5V2A 18 20 4 .8V0 .2 4 .5~6 .5V Under 90uA

<250mA 1 .5 sec 5~131 0F (-15~550C) 1 3/8"~ 2 1/8" (35-54mm) Furniture parts made of Zinc alloy and Latch made of SS304 4ea AAA alkaline batteries Remark: normally 4ea AAA batteries can support the lock to work for more than 10 months, anyway this is subject to quality of batteries and frequency of lock usage. 11. POPULAR QUESTIONS AND ANSWERS Q1: Dose ES0001 lock work with third-party parts like Latch Assembly?

A1: It is recommended to use the original parts for best performance and prem iu m qual ity leve l . Q2: What notification will I receive when the battery voltage runs to a low level?

A2: After the Fingerprint identification or mobile APP are successfully operated (the buzzer beeps once, the Fingerprint reader flashes green and red). When you unlock the device through mobile App, you will receive a notification message fo r low battery warning. Q3: How can I unlock ES0001 lock if battery runs out?

A3: Connect a power bank to the exterior Knob Module with Type-C cable as to activate for emergency access, then use Fingerprint reader or PIN Code for normal access operation. If this is still not working, please pull out the Exterior Cover Assembly and rotate it to dispose the back-up cylinder for key unlocking. Q4: If I order 3 locks will all they have the same key code?

A4: Each set of lock is keyed differently. Q5: If accidentally the lock is deleted from mobile app, what should I do?

A5: If you delete the lock in mobile app, while the lock can be still working, please reset the lock and connect it to mobile APP again. Q6: My Bluetooth won't connect, what should I do?

A6: 1. Upgrade to the latest version of the APP, authorize Bluetooth in the phone settings to allow access to the Tuya App, then try to connect again with the designated distance range. If the connection between Lockset and APP is still not successful, please contact our customer service (customers-ast@anlandst.com) for technical support. Q7: What notification will I receive when the battery voltage is low?

A7: When you use F ingerprint or mobile APP to unlock, the LED Indicator will flashes green and red as a warning signal. The remaining power can still provide about 500 times of unlocking even the warning signal happens, please replace battery within couple of days. Q8: How to enable passage mode?

A8 : Press set button on Interior Knob Module, then unlock the knob by Fingerprint identification, after buzzer beeps, passage mode enabled. Or you can enter "Setting" page in mobile APP, enable the passage mode. Q9: How to disable passage mode?

A9: Press set button on Interior knob Module, the passage mode will be disabled. Or you can enter "Setting" page in mobile APP, disable the passage mode. Q10: What is the difference between a dministrator (master) / no r m a l user?

A10: The first user to add the lock by mobile APP will be set as administrator (master), other members are normal users. Administrators F ingerprint can unlock even in the security mode, but normal user cannot unlock in the security mode. 12. FCC WARNING Any Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Note :

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation . This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment The devices has been evaluated to meet general RF exposure requirement the device can be used in portable exposure condition without restriction Anland Security Technology Revision: NR Language: English Size: A5 (14.8 X 21.0 cm) Remark: this document may be subject to change without notice Guangzhou Anland ST Co., Ltd

ey HU uy UUW UE ee vale 4 IAN E{A PAY 3 v ye i ef Wy yy ie 4 as ae i liye eee Ht I! UE II Il II II II II CO age EE Igt 1!

16 97 16 18 15 62 15 00 1442 13. 89 1342 1300 12.65 At 20 78 20 22 19 70 19 21 18 76 18 36 18 00 17_ 69 17_ 44 1S 22 625 21 704 20 83 20 19 23 18 52 17_ 875 17_ 33 33_ 94 32_56 31.24 30 28 84 27_78 26_ 83 26 8 h & 9 M% 9 % 10 10 % 10 % 11 Vie 5 5% 10 % 10 % 10 % 10 % 1 Ve 1 6 EY 1 6 1 a Ld ie i ha Bunece

et th lh Pinion hiddhid ehulalult lil OLL V ily GLL Ce en oo 5) il cladudakt Ol -

lilih Oem Tap LT] Ley reer eyar

= OIE -4--+ Gig---. A lciade

) 1

C5266091_X24_Ed.2 Guangzhou Anland ST Co., Ltd Attestation Statements TO:

Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 The Commission adopted rules covered telecommunications equipment and video surveillance equipment produced by entities identified on the Commissions Covered List1, which is periodically updated. See the Covered List for more details. This Attestation Statement is to confirm that we follow the Section 2.911(d)(5)(i)-(ii) that prohibit equipment authorization for 2BBSH-AST2017 Applicant Company name: Guangzhou Anland ST Co., Ltd Grantee code: 2BBSH FCC ID:

Contact Name: XM Yi Address: A1-561#, ChaoLian Building, 838# of 105 National Road, Dashi Street, Panyu District, Guangzhou City, Guangdong Province, China Telephone No:

Fax No:

Email: xm.yi_ast@anlandst.com 86-13421334895 i. ii.

(the applicant) certifies that

[Guangzhou Anland ST Co., Ltd]

the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. The applicant must sign this certification.

[Guangzhou Anland ST Co., Ltd] (the applicant) certifies that, as of the date of the filing of the application, the applicant [is not] (as a specifically named entity or any of its subsidiaries or affiliates) identified on the Covered List as an entity producing covered equipment. The applicant must sign this certification.

[Guangzhou Anland ST Co., Ltd] (the applicant) certifies that, as of the date of the filing of the application, the applicant [ is not] identified on the Covered List as an entity producing coveredequipment . Date: 2023/06/28 Applicants Name: XM Yi Title: Manager Signature 1 The Commissions Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commissions website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes covered equipment. https://www.fcc.gov/supplychain/coveredlist 1/1

Guangzhou Anland ST Co., Ltd Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject: Request for Confidentiality FCC ID: 2BBSH-AST2017 To Whom It May Concern, C5266091_X10_Ed.2 Date: 2023-06.28 Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules

(47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits ID Label/Location Attestation Statement External Photos Block Diagram Schematics Test Report Test Setup Photos Users Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) SDR Software / Security Info Long-Term Confidentiality No No No Short-Term Confidentiality NOTE 2 No No No No NOTE 1 NOTE 1 No No No No No No NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. short-term Confidentiality, the applicant requests the exhibits selected In case of above are withheld from public view for a period of ______ days from the date of the Grant of Equipment Authorization and prior to marketing. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. 1/1 C5266091_X10_Ed.2 Sincerely, Signature:

Name: XM Yi Title: Manager 2023.06.28 1/1

Guangzhou Anland ST Co., Ltd Product Similarity Declaration Product name:Electronic Knob Door Lock Model name:ES0001, ES0011, ES0021, ES0031, ES0041 FCC ID:2BBSH-AST2017 We (Guangzhou Anland ST Co., Ltd) hereby state that all the models are electrical identical including the same software parameter and hardware design (i.e., circuit design, PCB Layout, RF module/circuit, antenna type(s) and antenna location, components on PCB, etc.,), same mechanical structure and design (including product enclosure, materials, etc.,), the only difference is the model name. Signature:

Name:XM Yi Title: Manager Place, date:Jun 28, 2023

C5266091_X8_Ed.1 Letter of Authorization Guangzhou Anland ST Co., Ltd Company: Guangzhou Anland ST Co., Ltd Address: A1-561#, ChaoLian Building, 838# of 105 National Road, Dashi Street, Panyu District, Guangzhou City, Guangdong Province, China Product Name: Electronic Knob Door Lock Model Number: ES0001, ES0011, ES0021, ES0031, ES0041 FCC Identifier: 2BBSH-AST2017 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. is allowed to forward all Name: XM Yi Date: 2023.06.28 Title: Manager Signature of applicant:

1/1

US Agent for Service of Process LETTER OF ATTESTATION TO:

Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 US Agent for Service of Process:

Company Name: Wilson Tech Service LLC FRN: 0033402033 Contact Name: Wilson Cheung Address: 1312 17th Street Suite 692,Denver,CO,80202,US Telephone No: +1-716-965-5112 Email: Wilson.Cheung.FDA@gmail.com Applicant:

Company name:Guangzhou Anland ST Co., Ltd Product Description:Electronic Knob Door Lock Grantee code:2BBSH FCC ID:2BBSH-AST2017 Contact Name:XM Yi Address:A1-561#, ChaoLian Building, 838# of 105 National Road, Dashi Street, Panyu District, Guangzhou City, Guangdong Province, ChinaTelephone No:+86-13421334895 Email:xm.yi_ast@anlandst.com

[Guangzhou Anland ST Co., Ltd] certifies that, as of the date of this filing of the application with the TCB, [Wilson Tech Service LLC] is our designated US agent for service of process for the above referenced FCC ID. [SGuangzhou Anland ST Co., Ltd] accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any commission related proceeding involving equipment. [Wilson Tech Service LLC] accepts, as of the date of the filing of the application, the obligation of the designated US agent for service of process for the above reference FCC ID. The US Agent for Service of Process is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause 2.911. The Applicant is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause 2.911. Date: 2023/06/25 Applicants Name:XM Yi US Agents Name: Wilson Cheunc Title: Manager |

Signature For and on behalf of deve rscecovosooronssnsccescccoeeesneccosecebesecioonesesenese Authorized Signa 1/1