NIODESKTOP - TB SERIES FM TRANSMITTER Imported Electronic Component Stereo Sound U Disk Player Wind Speed Control Power Adjustable Intelligent Alarm PC Control FWD REF MHz Audio Volume Adjustment Audio Socket On/Off Setting Button Down Button Up Button Microphone socket Microphone Volume Adjustment Soundtrack Mode U Disk Play Alarm FWD REF Transmit Power Reflected Power MHz Working Frequency Precautions For Use There is high pressure inside the machine,maintenance can only be operated by professional and technical person. Please put the machine in a cool dry and ventilated environment for use,the ambient temperature should not be higher than 35 degree centigrades. After antenna installed,there should be 5 meters above from the ground and wall spacing as standard installation environment. When install the feed tube,be sure to tie the feed tube to the mounting rod with a tie to prevent the feed tube from pulling loose on the connector. Please do not turn on the machine without connecting the antenna. Please do not touch the antenna after machine is power on. Please do not use this machine in explosive antospheres(eg gas stations, gas,steam,etc.). Please comply with local radio regulations. Function and Parameter setting Power On/Off When the machine is connected to power, then it starts. In working condition, long press key, the machine enters standby mode. In standby mode, long press key, the machine goes into working condition. Frequency Adjustment In working condition, short press corner flashes, press Short press or or Long press button button or to adjust the frequency.
, frequency steps by 100K;
button,frequency continuously steps by 100K. button
, when the MHZ icon in the lower right Power Adjustment button, when the FWD to adjust the power; Short press icon on the screen is flashing, press or REF Short press displayed as reflected power. PS:
The 6-watt power shows 0.75 watts per cell, with a minimum of 0 cells and a maximum of 8 cells. The 15-watt power shows 1.9 watts per cell, with a minimum of 0 cells and a maximum of 8 cells. button Decrement;
icon is or Soundtrack Adjustment button In the working state, short press flashing, press is mono;
or button When the stereo channel.
, when the icon of screen power icon is to adjust the channel mode;
U Disk Outlet PC Control Power Socket Cooling Fan TNC Antenna Female seat Audio / Microphone Volume Adjustment Turn the audio knob / microphone knob clockwise to increase the volume;
turn counterclockwise to decrease the volume. Amplifier Temperature In working condition, short press the current temperature of the amplifier module. button, when the icon is displayed, it is U Disk Playback When the host is turned on, insert U disk, the screen displays icon;
press or buttonto switch songs;
Long press the button to switch the sound mode (NO normal, POP pop, JAZ Jazz, CLA classical, BAS bass). Long press the button to switch play mode (ALL ALL, FOL in sequence, ONE ONE, RAN) Input priority:
Audio cable > U disk play Lever antenna frequency length corresponding table MHZ Alarm Reminder Function When the machine is working, it sends alarm and the alarm icon corner of the screen. General troubleshooting:
Standing Wave Alarm 1.The antenna is not connected 2. Feeders rolled together, did not start;
3. Antenna installation from the ground, wall or metal objects too close, adjust the antenna flashes in the lower left installation location;
4. Antenna oscillator height and frequency do not match, adjust the height of the antenna to the launch point. Temperature alarm 1.Fan does not turn 2. The antenna does not match,which causes standing wave too large and temperature rises. Adjust the antenna oscillator height corresponding to the launch frequency or adjust the antenna position;
3. Into the outlet there are obstacles, blocked the flow of air temperature is too high;
4. engine room air convection, or the engine room temperature is too high. Technical Parameter NO. Item Working voltage Working current Frequency range Frequency stability Frequency step Environmental Operating temperature Output impedance RF output power Harmonic / clutter radiation Audio distortion Bluetooth distance Frequency response Resolution degree Input level Modulation frequency offset SNR Size Weight Technical Parameter
-30dBm
-30dBm Not Support g LCM FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RF Exposure Information The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.