WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6117300.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case Guangzhou Shikun Electronic Technology Company Limited SPECIFICATION SKO.W603.6 IEEE 802.11b/g/n 2T2R USB Wi-Fi Module Approved by Shikun Checked by Rechecked by Approved by Please send the original back to us after you have approved and signed. Approved by customer Comments Approved by Companys seal Customers Name:
CVTE REVISION HISTORY VERSION DATE BOARD ID PAGE DESCRIPTION AUTHOR V0 V4 2020.07.10 SKO.W603.6 A20233 First Issued. 2022.08.16 SKO.W603.6 Modify the product B20332 3 pictures . Lee Lee CVTE Content 1. Introduction.................................................................................................................1 2. FEATURES.................................................................................................................... 1 3. Block Diagram...................................................................................................2 4. Package Outline and Mounting...................................................... 2 5. Product Pictures............................................................................................... 3 6. Key Materials.....................................................................................................4 7. General Requirements................................................................................... 4 8. Electrical Characteristics...............................................................................4 8.1 IEEE 802.11b Section................................................................................................. 5 8.2 IEEE 802.11g Section................................................................................................. 5 8.3 IEEE 802.11n HT20 Section(2.4GHz)................................................................... 6 8.4 IEEE 802.11n HT40 Section(2.4GHz)................................................................... 7 9. Mechanical,Environmental and Reliability Tests...... 9 10. Package................................................................................................................... 11 11. Socket Specification.................................................................................. 12 CVTE SKO.W603.6 1. Introduction SKO.W603.6_02 module is based on MEDIATEK MT7603U solution. The MT7603U is a highly integrated Wi-Fi single chip which supports 300 Mbps PHY rate. It fully complies with IEEE 802.11n and IEEE 802.11 b/g standards, offering feature-rich wireless connectivity at high standards, and delivering reliable, cost-effective throughput from an extended distance. This documentation describes the engineering requirements specification. SKO.W603.6_02 MEDIATEK MT7603U MT7603U Wi-Fi 300 Mbps IEEE 802.11n IEEE 802.11 b/g 2. FEATURES Reserving System Chip Solution Band Dimensions IEEE Std. 802.11b IEEE Std. 802.11g IEEE Std. 802.11n MT7603U 2.4GHz 57.0mm30.0mm3.2mm SKO.W603.6_02 Ext-WIFI IEEE 802.11b/g/n 2.4GHz Ipex 57.0mm30.0mm3.2mm QR-ZZPJ-017A 1 CVTE 3. Block Diagram SKO.W603.6 SKO.W603.6 Block Diagram 4. Package Outline and Mounting Note:1. The unit is mm. 2.The tolerance of the external dimensions of the module is 0.2mm, and the tolerance of the board thickness and unmarked is 0.2mm. 1. mm 2.0.2mm0.2mm QR-ZZPJ-017A 2 CVTE Pin Definition SKO.W603.6 PIN SYMBOL DESCRIPTION 1 2 3 4 5 6 7 8 9 VDD_5V VDD_5V NC GND GND USB_DM USB_DP GND WoW 10 RESET VDD 5.0V \ +5.0V VDD 5.0V \ +5.0V NC \
Connected to Ground \
Connected to Ground \
USB2.0 DM Signal \ USB2.0 USB2.0 DP Signal \ USB2.0 Connected to Ground \
Wake on Wireless LAN \
10K 3.3V RESET \
(DCDC EN ) 5. Product Pictures top view QR-ZZPJ-017A 3 CVTE SKO.W603.6 bottom view 6. Key Materials
1 2 3 PCB MT7603U 48-QFN SKO.W603.6 FR-4,2LAY
,SPXO, 10ppm,12pF,SMD3225 40MHz 7. General Requirements No. 7-1 7-2 7-3 7-4 7-5 7-6 7-7 Feature Operation Voltage Current Consumption Ripple Operation Temperature Antenna Type Description 5.0V+/-0.5 800mA 250Vp-p 0C to +40C Internal antenna USB High Speed USB 2.0 Interface Storage Temperature
-40C to +85C 8. Electrical Characteristics The Test for electrical specification was performed under the following condition unless otherwise specified. Ambient condition Temperature
:25 5;
Power supply voltages5.0V
(10%) input power at the Module. 255 5.0V10%
Note: The channel 12-13 would be disabled when module used in America and Canada. QR-ZZPJ-017A 4 CVTE SKO.W603.6 8.1 IEEE 802.11b Section Items Specification Mode Channel Contents IEEE802.11b DBPSK, DQPSK and CCK and DSSS CH1 to CH13 TX Characteristics Min. Typ. Max. Unit Remark 1. Power Levels(Calibrated) 1) For Each antenna port 14 16 18 dBm 2. Spectrum Mask @ target power 1) fc +/-11MHz to +/-22MHz 2) fc > +/-22MHz 3 Constellation Error(EVM)@ target power 1) 1Mbps 2) 2Mbps 3) 5.5Mbps 4) 11Mbps 4. Frequency Error RX Characteristics 5 Minimum Input Level Sensitivity
(each chain) 1) 1Mbps (FER 8%) 2) 2Mbps (FER 8%) 3) 5.5Mbps (FER 8%) 4) 11Mbps (FER 8%)
-20 Min.
6 Maximum Input Level (FER 8%)
-10 8.2 IEEE 802.11g Section
-30
-50
-10
-10
-10
-10 20 Typ. Max.
-83
-80
-79
-76
dBr dBr dB dB dB dB ppm Unit dBm dBm dBm dBm dBm Items Specification Mode Channel Contents IEEE802.11g BPSK, QPSK, 16QAM, 64QAM and OFDM CH1 to CH13 TX Characteristics Min. Typ. Max. Unit Remark 1. Power Levels 1) For Each antenna port 12 14 16 dBm 2. Spectrum Mask @ target power 1) at fc +/-11MHz 2) at fc +/-20MHz 3) at fc > +/-30MHz 3 Constellation Error(EVM)@ target power 1) 6Mbps QR-ZZPJ-017A
5
-20
-28
-40 dBr dBr dBr
-5 dB CVTE 2) 9Mbps 3) 12Mbps 4) 18Mbps 5) 24Mbps 6) 36Mbps 7) 48Mbps 8) 54Mbps 4 Frequency Error RX Characteristics 5 Minimum Input Level Sensitivity
(each chain) 1) 6Mbps (PER 10%) 2) 9Mbps (PER 10%) 3) 12Mbps (PER 10%) 4) 18Mbps (PER 10%) 5) 24Mbps (PER 10%) 6) 36Mbps (PER 10%) 7) 48Mbps (PER 10%) 8) 54Mbps (PER 10%)
-20 Min.
6 Maximum Input Level (PER 10%)
-20 SKO.W603.6
-8
-10
-13
-16
-19
-22
-25 20 Typ. Max.
-85
-84
-82
-80
-77
-73
-69
-65
dB dB dB dB dB dB dB ppm Unit dBm dBm dBm dBm dBm dBm dBm dBm dBm 8.3 IEEE 802.11n HT20 Section(2.4GHz) Items Contents Specification Mode Channel EEE802.11n HT20 @ 2.4GHz BPSK, QPSK, 16QAM, 64QAM and OFDM CH1 to CH13 TX Characteristics Min. Typ. Max. Unit 1. Power Levels 1) For Each antenna port 11 13 15 dBm 2. Spectrum Mask @ target power 1) at fc +/-11MHz 2) at fc +/-20MHz 3) at fc > +/-30MHz 3. Constellation Error(EVM)@ target power 1) MCS0 2) MCS1 3) MCS2 4) MCS3 5) MCS4 6) MCS5 7) MCS6 8) MCS7 QR-ZZPJ-017A
-20
-28
-45
-5
-10
-13
-16
-19
-22
-25
-28 dBr dBr dBr dB dB dB dB dB dB dB dB
6 CVTE 4. Frequency Error RX Characteristics 5. Minimum Input Level Sensitivity
-20 Min.
Typ. 20 Max.
(each chain) 1) MCS0 (PER 10%) 2) MCS1 (PER 10%) 3) MCS2 (PER 10%) 4) MCS3 (PER 10%) 5) MCS4 (PER 10%) 6) MCS5 (PER 10%) 7) MCS6 (PER 10%) 8) MCS7 (PER 10%)
6. Maximum Input Level (PER 10%)
-20
-82
-79
-77
-74
-70
-66
-65
-64
SKO.W603.6 ppm Unit dBm dBm dBm dBm dBm dBm dBm dBm dBm 8.4 IEEE 802.11n HT40 Section(2.4GHz) Items Contents Specification Mode Channel TX Characteristics 1. Power Levels (Calibrated) IEEE802.11n HT40 @ 2.4GHz BPSK, QPSK, 16QAM, 64QAM and OFDM CH3 to CH11 Min. Min. Typ. Typ. Max. Max. Unit Unit Remark 1) For Each antenna port 11 13 15 dBm 2. Spectrum Mask @target power 1) at fc +/-22MHz 2) at fc +/-40MHz 3) at fc > +/-60MHz 3. Constellation Error(EVM)@ target power 1) MCS0 2) MCS1 3) MCS2 4) MCS3 5) MCS4 6) MCS5 7) MCS6 8) MCS7 4. Frequency Error RX Characteristics 5. Minimum Input Level Sensitivity
(each chain) 1) MCS0 (PER 10%) 2) MCS1 (PER 10%) QR-ZZPJ-017A
-20
-28
-45
-5
-10
-13
-16
-19
-22
-25
-28 20 Typ. Max.
-79
-76 dBr dBr dBr dB dB dB dB dB dB dB dB ppm Unit dBm dBm
-20 Min.
7 CVTE 3) MCS2 (PER 10%) 4) MCS3 (PER 10%) 5) MCS4 (PER 10%) 6) MCS5 (PER 10%) 7) MCS6 (PER 10%) 8) MCS7 (PER 10%)
6. Maximum Input Level (PER 10%)
-20 SKO.W603.6
-74
-71
-67
-63
-62
-61
dBm dBm dBm dBm dBm dBm dBm QR-ZZPJ-017A 8 CVTE SKO.W603.6 9. Mechanical,Environmental and Reliability Tests Test Items Test Conditions Qty Criteria Condition 9-1 Drop test The packed samples was tested at below condition:
Drop height:
760mm(0.5~9.5kg 610mm(9.5~18.5kg) Drop time: 1x corner, 3x edge and 6x face. X-Y-Z direction, first After test, the outer box and inner box 1xBox will not been broken by appearance visual inspection, and the products should be ok. Frequency changing from After test, the outer box and inner box 9-2 Vibration 10Hz to 30Hz to will not been broken by appearance test 10Hz,amplitude 2.0mm, 1xBox visual inspection and the products should 5 times vibrations, 5x times be ok. vibration. 1.After soldering, the soldered area must be covered by a smooth bright solder layer, some deficiencies such as a small amount of the pinhole, not wetting are allowed, but the deficiencies can not be in the same place 2. At least 90% of soldered area shall be covered continuously by the soldering material. After test, the products appearance, power, EVM and frequency error functional parameter shall be satisfied with the test specification. After test, the products appearance, power, EVM and frequency error functional parameter shall be satisfied with the test specification. 3 4 4 Soldering ability test
(Only for SKI Soldering temperature:
2455 9-3 module) Soldering duration:
30.5S High Temperature and Leave samples in 60, 90%
Humidity RH @ 24 hours Operation Test Low Temperature Leave samples in -15 Operation
@24 hours 9-4 9-5 Test High Temperature 9-6 and Humidity Start Test Leave samples in 60, 90% RH for 4x hours After test, power on and off the samples 4 for 3x tiems, the samples should be able to start normally QR-ZZPJ-017A 9 CVTE Leave samples in -15 for 4x hours After test, power on and off the samples 4 for 3x tiems, the samples should be able to start normally SKO.W603.6 Low 9-7 temperature start test High Temperature 9-8 and Humidity Storage Test Low Leave samples in 85, 95%
RH @ 48 hours 9-9 Temperature Storage Test Leave samples in -40, @48 hours 9-10 Thermal
-40~85dwell time Shock Test 30min50cycles 9-11 Aging Test 60120Hrs 10 4 4 4 After test, the products appearance, power, EVM and frequency error functional parameter shall be satisfied with the test specification. After test, the products appearance, power, EVM and frequency error functional parameter shall be satisfied with the test specification. After test, the products appearance, power, EVM and frequency error functional parameter shall be satisfied with the test specification. The products at high temperature for a long time can continuous work normally The Sample shall has no minor or major 9-12 Salt spray test NSS,35,PH:6.5~7.2, 2 defects, such as physical damage, crack, corrosion, deformation etc;
Discharge voltage:
1kV C: 150pF 9-13 ESD Discharge resistance330 3 The products can recoverable smoothly after ESD test. Positive10 times 1 time for each second QR-ZZPJ-017A 10 CVTE 10. Package 1 SKO.W603.6 2 3 QR-ZZPJ-017A 11 CVTE 11. Socket Specification SKO.W603.6 QR-ZZPJ-017A 12 CVTE FCC Statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful
(2) this device must accept any interference received, including interference that may cause undesired operation. interference, and This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the If this equipment does cause harmful interference to radio or receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. List of applicable FCC rules This module has been tested and found to comply with part 15 requirements for Modular Approval. Antenna Placement Within the Host Platform The module is tested for standalone mobile RF exposure use condition.
(1) The antenna must be installed such that 20 cm is maintained between the antenna and users,
(2) The transmitter module may not be co-located with any other transmitter or antenna. In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. RF exposure considerations This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Antenna Type and Gain The following antennas have been certified for use with this module. Only antennas of the same type with equal or lower gain may also be used with this module. Other types of antennas and/or higher gain antennas may require the additional authorization for operation. Antenna Specification list below:
Antenna Type PIFA PCBA Frequency Bands (MHz) 2400 ~ 2483.5 2400 ~ 2483.5 Max. Antenna Gain (dBi) 4.93 1.72 End Product Labeling When the module is installed in the host device, the FCC ID label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily re-moved. If not, a second label must be placed on the outside of the final device that contains the following text: Contains FCC ID: 2AR82-SKOW603601. The FCC ID can be used only when all FCC compliance requirements are met. The end product shall bear the following 15.19 statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. Information on test modes and additional testing requirements This transmitter is tested in a standalone mobile RF exposure condition and any co-located or simultaneous transmission with other transmitter(s) class II permissive change re-evaluation or new certification. Part 15 Subpart B disclaimer This transmitter module is tested as a subsystem and its certification does not cover the FCC Part 15 Subpart B rule requirement applicable to the final host. The final host will still need to be reassessed for compliance to this portion of rule requirements if applicable. As long as all conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Important Note In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for reevaluating the end product (including the transmitter) and obtaining a separate FCC authorization. Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The host integrator must follow the integration instructions provided in this document and ensure that the composite-system end product complies with the requirements by a technical assessment or evaluation to the rules and to KDB Publication 996369. The host integrator installing this module into their product must ensure that the final composite product complies with the requirements by a technical assessment or evaluation to the rules, including the transmitter operation and should refer to guidance in KDB 996369. OEM/Host manufacturer responsibilities OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule such as FCC Part 15 Subpart B before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and EMF essential requirements of the FCC rules. This module must not be incorporated into any other device or system without retesting for compliance as multi-radio and combined equipment ISED Statement:
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de classe B est conforme la norme canadienne ICES-003. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
1) 2) This device may not cause interference, and This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables auxappareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:
1) 2) l'appareil ne doit pas produire de brouillage, et l'utilisateur de l'appareil doit accepter tout brouillage adiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. RF Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Dclaration d'exposition aux radiations:
Cet appareil est conforme aux limites d'exposition aux rayonnements dfinies pour un environnement non contrl. Cet quipement doit tre install et utilis une distance minimale de 20 centimtres entre le radiateur et votre corps. This device is intended only for OEM integrators under the following conditions:
The transmitter module may not be co-located with any other transmitter or antenna. As long as above conditions is met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. 1) Operation shall be limited to indoor use only; and 2) Operation on oil platforms, cars, trains, boats and aircraft shall be prohibited except for on large aircraft flying above 10,000 ft. 3) This device is limited to under control an indoor access point or an indoor subordinate device and shall not be capable of initiating a network. Cet appareil est conu uniquement pour les intgrateurs OEM dans les conditions suivantes:
Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. Tant que les 1 conditions ci-dessus sont remplies, des essais supplmentaires sur l'metteur ne seront pas ncessaires. Toutefois, l'intgrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformit supplmentaires requis pour ce module install. 1) Utilisation limite lintrieur seulement;
2) Utilisation interdite bord de plateformes de forage ptrolier, de voitures, de trains, de bateaux et daronefs, sauf bord dun gros aronef volant plus de 10 000 pieds daltitude. 3) Ce dispositif est limit un point daccs lintrieur ou un dispositif subordonn lintrieur et ne doit pas tre capable dinitier un rseau. IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization. NOTE IMPORTANTE:
Dans le cas o ces conditions ne peuvent tre satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre metteur), l'autorisation du Canada n'est plus considr comme valide et IC ne peut pas tre utilis sur le produit final. Dans ces circonstances, l'intgrateur OEM sera charg de rvaluer le produit final (y compris l'metteur) et l'obtention d'une autorisation distincte au Canada. Required end product labeling:
This transmitter module is authorized only for use in device where the antenna may be installed and operated with greater than 20cm between the antenna and users. The final end product must be labeled in a visible area with the following: Contains IC:
24728-SKOW603601. Plaque signaltique du produit final Ce module metteur est autoris uniquement pour une utilisation dans un appareil o lantenne peut tre installe et utilise plus de 20 cm entre lantenne et les utilisateurs. Le produit final doit tre tiquet dans un endroit visible avec l'inscription suivante: "Contient des IC: 24728-SKOW603601". Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. The following text, or an equivalent notice, that shall be displayed in a conspicuous location, either in the user manual or on the device, or both:
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
1) This device may not cause interference. 2) This device must accept any interference, including interference that may cause undesired operation of the device. Manuel d'information l'utilisateur final L'intgrateur OEM doit tre conscient de ne pas fournir des informations l'utilisateur final quant la faon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intgre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations rglementaires requises et avertissements comme indiqu dans ce manuel. lnonc qui suit, ou lquivalent, un endroit bien en vue dans le manuel dutilisation ou sur lappareil, ou encore aux deux endroits :
Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
1. 2. Lappareil ne doit pas produire de brouillage;
Lappareil doit accepter toute interfrence, y compris toute interfrence pouvant entraner un fonctionnement indsirable du dispositif. Antennas The following antennas have been certified for use with this module; antennas of the same type with equal or lower gain may also be used with this module. The antenna must be installed such that 20F cm can be maintained between the antenna and users. This radio transmitter has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Antenna Specification list below:
Antenna Type PIFA PCBA Frequency Bands (MHz) 2400 ~ 2483.5 2400 ~ 2483.5 Max. Antenna Gain (dBi) 4.93 1.72 ANTENNE Les antennes suivantes ont t certifies pour une utilisation avec ce module; des antennes du mme type gain gal ou infrieur peuvent galement tre utilises avec ce module. L'antenne doit tre installe de telle sorte que 20 cm puissent tre maintenus entre l'antenne et les utilisateurs. Cet metteur radio a t approuv par Innovation, Sciences et Dveloppement conomique Canada pour fonctionner avec les types d'antenne numrs ci-dessous, avec le gain maximal autoris indiqu. Les types d'antenne non inclus dans cette liste qui ont un gain suprieur au gain maximum indiqu pour tout type rpertori sont strictement interdits pour l'utilisation avec cet appareil.