SPECIFICATION SPEC. NO. REV 1.1 DATE 04. 26. 2015 PRODUCT NAME AP6255 APPROVED CHECKED PREPARED DCC ISSUE NAME AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
AMPAK AP6255 WiFi 11ac + Bluetooth 4.1 Module Spec Sheet AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
1 AP6255 Datasheet Revision History Date Revision Content Revised By Version 2015/04/09
- Preliminary 2015/04/26
- Add GPIO pin definiion Gary Gary 1.0 1.1 AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
2 AP6255 Datasheet Contents Contents ................................................................................................................... 3 1. Introduction ......................................................................................................... 4 2. Features............................................................................................................... 5 3. Deliverables ........................................................................................................ 6 3.1 Deliverables .................................................................................................... 6 3.2 Regulatory certifications ................................................................................. 6 4. General Specification ......................................................................................... 7 4.1 General Specification ...................................................................................... 7 4.2 Voltages .......................................................................................................... 7 4.2.1 Absolute Maximum Ratings .................................................................... 7 4.2.2 Recommended Operating Rating ........................................................... 7 The module requires two power supplies: VBAT and VDDIO. ........................ 7 5. Wi-Fi RF Specification ........................................................................................ 8 5.1 2.4GHz RF Specification................................................................................. 8 5.1 5GHz RF Specification.................................................................................. 10 6. Bluetooth Specification .................................................................................... 13 6.1 Bluetooth Specification ................................................................................. 13 7. Pin Assignments ............................................................................................... 14 7.1 Pin Outline .................................................................................................... 14 7.2 Pin Definition ................................................................................................ 14 8. Dimensions ....................................................................................................... 16 8.1 Physical Dimensions .................................................................................... 16 8.2 Layout Recommendation .............................................................................. 17 9. External clock reference .................................................................................. 18 10.1 SDIO Pin Description .................................................................................. 19 10. Host Interface Timing Diagram ........................................................................ 20 10.1 Power-up Sequence Timing Diagram ......................................................... 20 10.2 SDIO Default Mode Timing Diagram........................................................... 22 10.3 SDIO High Speed Mode Timing Diagram ................................................... 23 10.4 SDIO Bus Timing Specifications in SDR Modes ......................................... 24 10.5 SDIO Bus Timing Specifications in DDR50 Mode ....................................... 26 11. Recommended Reflow Profile ......................................................................... 28 Solder Paste definition .......................................................................................... 29 12. Package Information ........................................................................................ 30 12.1 Label ........................................................................................................... 30 Label C Inner box label . ................................................................................... 30 Label D Carton box label . ................................................................................ 30 AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
3 12.2 Dimension ................................................................................................... 31 12.3 MSL Level / Storage Condition ................................................................... 33 AP6255 Datasheet 1. Introduction AMPAK Technology would like to announce a low-cost and low-power consumption module which has all of the Wi-Fi, Bluetooth functionalities. The highly integrated module makes the possibilities of web browsing, VoIP, Bluetooth headsets applications. With seamless roaming capabilities and advanced security, also could interact with different vendors 802.11a/b/g/n/ac Access Points in the wireless LAN. The wireless module complies with IEEE 802.11 a/b/g/n/ac standard and it can achieve up to a speed of 433.3Mbps with single stream in 802.11ac draft to connect to the wireless LAN. The integrated module provides SDIO interface for Wi-Fi, UART / PCM interface for Bluetooth. This compact module is a total solution for a combination of Wi-Fi + BT technologies. The module is specifically developed for Smart phones and Portable devices. AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
4 AP6255 Datasheet 2. Features
IEEE 802.11a/b/g/n/ac dual-band radio with virtual-simultaneous dual-band operation
Single-stream spatial multiplexing up to 433.3 Mbps data rate.
Supports 20, 40, 80 MHz channels with optional SGI(256 QAM modulation)
Bluetooth V4.0+EDR with integrated Class 1 PA and Low Energy (BLE) support
Concurrent Bluetooth, and WLAN operation
Simultaneous BT/WLAN receive with single antenna
Supports standard SDIO v3.0 and backward compatible with SDIO v2.0 host interfaces.
- SDIO v3.0(4-bit) up to 208 MHz clock rate in SDR104 mode
BT host digital interface:
- UART (up to 4 Mbps)
IEEE Co-existence technologies are integrated die solution
ECI enhanced coexistence support, ability to coordinate BT SCO transmissions around WLAN receives A simplified block diagram of the module is depicted in the figure below. AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
5 AP6255 Datasheet 3. Deliverables 3.1 Deliverables The following products and software will be part of the product.
Module with packaging
Evaluation Kits
Software utility for integration, performance test.
Product Datasheet.
Agency certified pre-tested report with the adapter board. 3.2 Regulatory certifications The product delivery is a pre-tested module, without the module level certification. For module approval, the platforms antennas are required for the certification. AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
6 AP6255 Datasheet 4. General Specification 4.1 General Specification Model Name AP6255 Product Description Support Wi-Fi/Bluetooth functionalities Dimension WiFi Interface BT Interface L x W x H: 12 x 12 x 1.5 (typical) mm SDIO v2.0/v3.0 UART / PCM Operating temperature
-30C to 85C Storage temperature
-40C to 85C Humidity Operating Humidity 10% to 95% Non-Condensing Storage Humidity 5% to 95% Non-Condensing 4.2 Voltages 4.2.1 Absolute Maximum Ratings Description Min. Max. Unit Input supply Voltage Digital/Bluetooth/SDIO/ I/O Voltage
-0.5 6
-0.5 3.9 V V Symbol VBAT VDDIO 4.2.2 Recommended Operating Rating The module requires two power supplies: VBAT and VDDIO. Min. Typ. Max. Unit Operating Temperature VBAT VDDIO
-30 3.13 1.71 25 3.6 1.8 85 4.8 3.63 deg.C V V AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
7 AP6255 Datasheet 5. Wi-Fi RF Specification 5.1 2.4GHz RF Specification Conditions : VBAT=3.6V ; VDDIO=3.3V ; Temp:25C Feature Description WLAN Standard IEEE 802.11b/g/n/ac, WiFi compliant Frequency Range 2.400 GHz ~ 2.497 GHz (2.4 GHz ISM Band) Number of Channels 2.4GHzCh1 ~ Ch14 Modulation 802.11g/n : 64-QAM,16-QAM, QPSK, BPSK 802.11b : DQPSK, DBPSK, CCK 802.11ac : 256-QAM, 64-QAM,16-QAM, QPSK, BPSK 802.11b /CCK : 16 dBm 1.5 dB @ EVM -9dB Output Power 802.11g /64-QAM(R=3/4) : 15 dBm 1.5 dB @ EVM -25dB 802.11n /64-QAM(R=5/6) : 14 dBm 1.5 dB @ EVM -28dB
- 1Mbps PER @ -96 dBm, typical Receive Sensitivity
- 2Mbps PER @ -90 dBm, typical
(11b) @8% PER
- 5.5Mbps PER @ -88 dBm, typical
- 11Mbps PER @ -87 dBm, typical
- 6Mbps PER @ -90 dBm, typical
- 9Mbps PER @ -88 dBm, typical
- 12Mbps PER @ -87 dBm, typical Receive Sensitivity
- 18Mbps PER @ -85 dBm, typical
(11g) @10% PER
- 24Mbps PER @ -83 dBm, typical
- 36Mbps PER @ -80 dBm, typical
- 48Mbps PER @ -76 dBm, typical
- 54Mbps PER @ -74 dBm, typical
- MCS=0 PER @ -89 dBm, typical
- MCS=1 PER @ -85 dBm, typical
- MCS=2 PER @ -84 dBm, typical
- MCS=3 PER @ -80 dBm, typical
- MCS=4 PER @ -77 dBm, typical
- MCS=5 PER @ -75 dBm, typical
- MCS=6 PER @ -72 dBm, typical
- MCS=7 PER @ -71 dBm, typical Receive Sensitivity
(11n,20MHz)
@10% PER Receive Sensitivity
- MCS=0 PER @ -89 dBm, typical
(11n,40MHz)
- MCS=1 PER @ -85 dBm, typical AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
8
@10% PER
- MCS=2 PER @ -84 dBm, typical AP6255 Datasheet
- MCS=3 PER @ -80 dBm, typical
- MCS=4 PER @ -76 dBm, typical
- MCS=5 PER @ -72 dBm, typical
- MCS=6 PER @ -70 dBm, typical
- MCS=7 PER @ -69 dBm, typical
- MCS=0 PER @ -90 dBm, typical
- MCS=1 PER @ -87 dBm, typical
- MCS=2 PER @ -86 dBm, typical Receive Sensitivity
- MCS=3 PER @ -82 dBm, typical
(11ac,20MHz)
- MCS=4 PER @ -79 dBm, typical
@10% PER
- MCS=5 PER @ -75 dBm, typical Receive Sensitivity
(11ac,40MHz)
@10% PER
- MCS=6 PER @ -73 dBm, typical
- MCS=7 PER @ -72 dBm, typical
- MCS=8 PER @ -67 dBm, typical
- MCS=0 PER @ -88 dBm, typical
- MCS=1 PER @ -85 dBm, typical
- MCS=2 PER @ -83 dBm, typical
- MCS=3 PER @ -80 dBm, typical
- MCS=4 PER @ -77 dBm, typical
- MCS=5 PER @ -72 dBm, typical
- MCS=6 PER @ -71 dBm, typical
- MCS=7 PER @ -69 dBm, typical
- MCS=8 PER @ -65 dBm, typical
- MCS=9 PER @ -64 dBm, typical 802.11b : -10dBm Maximum Input Level 802.11g/n : -20dBm 802.11ac : -30dBm Antenna Reference Small antennas with 0~2 dBi peak gain AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
9 AP6255 Datasheet 5.1 5GHz RF Specification Conditions : VBAT=3.6V ; VDDIO=3.3V ; Temp:25C Feature Description WLAN Standard IEEE 802.11a/b/g/n/ac, Wi-Fi compliant Frequency Range Number of Channels 5.0GHzPlease see the table1 4.900 GHz ~ 5.845 GHz (5.0 GHz ISM Band) Modulation 802.11a/n : 64-QAM,16-QAM, QPSK, BPSK 802.11ac : 256-QAM, 64-QAM,16-QAM, QPSK, BPSK Output Power 802.11a /64-QAM(R=3/4) : 14 dBm 1.5 dB @ EVM -25dB 802.11n /64-QAM(R=5/6) : 13 dBm 1.5 dB @ EVM -28dB 802.11ac/256-QAM(R=3/4) : 12 dBm 1.5 dB @ EVM -30dB 802.11ac/256-QAM(R=5/6) : 10 dBm 1.5 dB @ EVM -32dB Receive Sensitivity
(11a, 20MHz) @10%
PER Receive Sensitivity
(11n,20MHz)
@10% PER Receive Sensitivity
(11n,40MHz)
@10% PER
- 6Mbps PER @ -91 dBm, typical
- 9Mbps PER @ -89 dBm, typical
- 12Mbps PER @ -88 dBm, typical
- 18Mbps PER @ -86 dBm, typical
- 24Mbps PER @ -82 dBm, typical
- 36Mbps PER @ -79 dBm, typical
- 48Mbps PER @ -74 dBm, typical
- 54Mbps PER @ -73 dBm, typical
- MCS=0 PER @ -90 dBm, typical
- MCS=1 PER @ -88 dBm, typical
- MCS=2 PER @ -85 dBm, typical
- MCS=3 PER @ -82 dBm, typical
- MCS=4 PER @ -78 dBm, typical
- MCS=5 PER @ -74 dBm, typical
- MCS=6 PER @ -72 dBm, typical
- MCS=7 PER @ -71 dBm, typical
- MCS=0 PER @ -88 dBm, typical
- MCS=1 PER @ -85 dBm, typical
- MCS=2 PER @ -83 dBm, typical
- MCS=3 PER @ -79 dBm, typical
- MCS=4 PER @ -76 dBm, typical
- MCS=5 PER @ -71 dBm, typical
- MCS=6 PER @ -70 dBm, typical
- MCS=7 PER @ -68 dBm, typical AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
10 AP6255 Datasheet
- MCS=0 PER @ -89 dBm, typical
- MCS=1 PER @ -87 dBm, typical
- MCS=2 PER @ -84 dBm, typical Receive Sensitivity
- MCS=3 PER @ -81 dBm, typical
(11ac,20MHz)
- MCS=4 PER @ -77 dBm, typical
@10% PER
- MCS=5 PER @ -73 dBm, typical
- MCS=6 PER @ -71 dBm, typical
- MCS=7 PER @ -70 dBm, typical
- MCS=8 PER @ -66 dBm, typical
- MCS=0 PER @ -87 dBm, typical
- MCS=1 PER @ -83 dBm, typical
- MCS=2 PER @ -81 dBm, typical
- MCS=3 PER @ -78 dBm, typical
- MCS=4 PER @ -75 dBm, typical
- MCS=5 PER @ -70 dBm, typical
- MCS=6 PER @ -68 dBm, typical
- MCS=7 PER @ -66 dBm, typical
- MCS=8 PER @ -64 dBm, typical
- MCS=9 PER @ -63 dBm, typical
- MCS=0 PER @ -83 dBm, typical
- MCS=1 PER @ -80 dBm, typical
- MCS=2 PER @ -78 dBm, typical
- MCS=3 PER @ -74 dBm, typical
- MCS=4 PER @ -71 dBm, typical
- MCS=5 PER @ -69 dBm, typical
- MCS=6 PER @ -65 dBm, typical
- MCS=7 PER @ -63 dBm, typical
- MCS=8 PER @ -60 dBm, typical
- MCS=9 PER @ -59 dBm, typical Receive Sensitivity
(11ac,40MHz)
@10% PER Receive Sensitivity
(11ac,80MHz)
@10% PER Maximum Input Level 802.11a/n : -20dBm 802.11ac : -30dBm Antenna Reference Small antennas with 0~2 dBi peak gain AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
11 AP6255 Datasheet Operating Channel Numbers Channel center frequencies(MHz) 36 40 44 48 52 56 60 64 100 104 108 112 116 120 124 128 132 136 140 149 153 157 161 165 5180 5200 5220 5240 5260 5280 5300 5320 5500 5520 5540 5560 5580 5600 5620 5640 5660 5680 5700 5745 5765 5785 5805 5825 15GHz Channel table Band (GHz) 5.15GHz~5.25GHz 5.25GHz~5.35GHz 5.5GHz~5.7GHz 5.725GHz~5.825GHz AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
12 AP6255 Datasheet 6. Bluetooth Specification 6.1 Bluetooth Specification Conditions : VBAT=3.6V ; VDDIO=3.3V ; Temp:25C Feature Description General Specification Bluetooth Standard Bluetooth V4.0 of 1, 2 and 3 Mbps. Host Interface UART Antenna Reference Small antennas with 0~2 dBi peak gain Frequency Band 2402 MHz ~ 2480 MHz Number of Channels 79 channels Modulation FHSS, GFSK, DPSK, DQPSK RF Specification Min. Typical. Max. Output Power (Class 1.5) Output Power (Class 2) Sensitivity @ BER=0.1%
for GFSK (1Mbps) Sensitivity @ BER=0.01%
for /4-DQPSK (2Mbps) Sensitivity @ BER=0.01%
for 8DPSK (3Mbps) 9 dBm 2 dBm
-86 dBm
-86 dBm
-80 dBm GFSK (1Mbps) :-20dBm Maximum Input Level
/4-DQPSK (2Mbps) :-20dBm 8DPSK (3Mbps) :-20dBm AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
13 AP6255 Datasheet 7. Pin Assignments 7.1 Pin Outline
< TOP VIEW >
7.2 Pin Definition Name GND WL_BT_ANT Type I/O NO 1 2 3 4 5 6 7 8 9 10 11 12 GND NC NC BT_WAKE BT_HOST_WAKE NC VBAT XTAL_IN XTAL_OUT WL_REG_ON 13 WL_HOST_WAKE Description Ground connections RF I/O port Ground connections Floating (Dont connected to ground) Floating (Dont connected to ground) HOST wake-up Bluetooth device Bluetooth device to wake-up HOST Floating (Dont connected to ground) Main power voltage source input Crystal input Crystal output Power up/down internal regulators used by WiFi section WLAN to wake-up HOST I O P I O I O AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
14 SDIO_DATA_2 SDIO_DATA_3 SDIO_DATA_CMD SDIO_DATA_CLK SDIO_DATA_0 SDIO_DATA_1 GND VIN_LDO_OUT VDDIO VIN_LDO LPO PCM_OUT PCM_CLK PCM_IN PCM_SYNC SDIO_VSEL NC GND NC GND BT_REG_ON NC GND GPIO_6 GPIO_3 GPIO_5 GPIO_2 UART_RTS_N UART_TXD UART_RXD UART_CTS_N TP1(NC) TP2(NC) TP3(NC) 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 I/O I/O I/O I/O I/O I/O P P P I O I/O I I/O I/O I I/O I/O I/O I/O O O I I AP6255 Datasheet SDIO data line 2 SDIO data line 3 SDIO command line SDIO clock line SDIO data line 0 SDIO data line 1 Ground connections Internal Buck voltage generation pin I/O Voltage supply input Internal Buck voltage generation pin External Low Power Clock input (32.768KHz) PCM Data output PCM clock PCM data input PCM sync signal SDIO mode selection pin Floating (Dont connected to ground) Ground connections Floating (Dont connected to ground) Ground connections Power up/down internal regulators used by BT section Floating (Dont connected to ground) Ground connections GPIO configuration pin GPIO configuration pin GPIO configuration pin GPIO configuration pin Bluetooth UART interface Bluetooth UART interface Bluetooth UART interface Bluetooth UART interface Floating (Dont connected to ground) Floating (Dont connected to ground) Floating (Dont connected to ground) AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
15 AP6255 Datasheet 8. Dimensions 8.1 Physical Dimensions
(Unit: mm)
< TOP VIEW >
< Side View >
< TOP VIEW >
AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
16 AP6255 Datasheet 8.2 Layout Recommendation
(Unit: mm)
< TOP VIEW >
AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
17 AP6255 Datasheet 9. External clock reference External LPO signal characteristics Parameter Specification Units Nominal input frequency Frequency accuracy Duty cycle Input signal amplitude Signal type Input impedance Clock jitter (integrated over 300Hz 15KHz) Output high voltage 32.768 30 30 - 70 400 to 1800 Square-wave
>100k
<5
<1 0.7Vio - Vio kHz ppm
%
mV, p-p
-
pF Hz V AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
18 10.1 SDIO Pin Description All three package options of the WLAN section provide support for SDIO version 3.0 AP6255 Datasheet including the new UHS-I modes:
DS: Default speed up to 25MHz (3.3V signaling).
HS: High speed up to 50MH (3.3V signaling).
SDR12: SDR up to 25MHz (1.8V signaling).
SDR25: SDR up to 50MHz (1.8V signaling).
SDR50: SDR up to 100MHz (1.8V signaling).
SDR104: SDR up to 208MHz (1.8V signaling).
DDR50: DDR up to 50MHz (1.8V signaling). The SDIO interface also has the ability to map the interrupt signal on to a GPIO pin for applications requiring an interrupt different from the one provided by SDIO interface. The ability to force control of gated clocks from within the device is also provided. The following three functions are supported:
Function 0 Standard SDIO function (Max BlockSize / ByteCount = 32B)
Function 1 Backplane Function to access the internal System On Chip (SOC) address space (Max BlockSize / ByteCount = 64B)
Function 2 WLAN Function for efficient WLAN packet transfer through DMA (Max BlockSize/ByteCount=512B) SDIO Pin Description SD 4-Bit Mode DATA0 Data Line 0 DATA1 Data Line 1 or Interrupt DATA2 Data Line 2 or Read Wait DATA3 Data Line 3 CLK Clock CMD Command Line AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
19 AP6255 Datasheet 10. Host Interface Timing Diagram 10.1 Power-up Sequence Timing Diagram The module has signals that allow the host to control power consumption by enabling or disabling the Bluetooth, WLAN and internal regulator blocks. These signals are described below. Additionally, diagrams are provided to indicate proper sequencing of the signals for carious operating states. The timing value indicated are minimum required values: longer delays are also acceptable. WL_REG_ON: Used by the PMU to power up or power down the internal regulators used by the WLAN section. When this pin is high, the regulators are enabled and the WLAN section is out of reset. When this pin is low the WLAN section is in reset. BT_REG_ON: Used by the PMU to power up or power down the internal regulators used by the BT section. Low asserting reset for Bluetooth. This pin has no effect on WLAN and does not control any PMU functions. This pin must be driven high or low
(not left floating). WLAN=ON, Bluetooth=ON AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
20 AP6255 Datasheet WLAN=OFF, Bluetooth=OFF WLAN=ON, Bluetooth=OFF WLAN=OFF, Bluetooth=ON AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
21 10.2 SDIO Default Mode Timing Diagram AP6255 Datasheet AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
22 10.3 SDIO High Speed Mode Timing Diagram AP6255 Datasheet AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
23 10.4 SDIO Bus Timing Specifications in SDR Modes Clock timing (SDR Modes) AP6255 Datasheet Card Input timing (SDR Modes) AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
24 Card output timing (SDR Modes up to 100MHz) AP6255 Datasheet Card output timing (SDR Modes 100MHz to 208MHz) AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
25 t OP Consideration for Variable Data Window (SDR 104 Mode) AP6255 Datasheet 10.5 SDIO Bus Timing Specifications in DDR50 Mode AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
26 Data Timing AP6255 Datasheet AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
27 11. Recommended Reflow Profile AP6255 Datasheet Referred to IPC/JEDEC standard. Peak Temperature : <250C Number of Times : 2 times 250 2.5C/sec 40~70 sec 2.5 /sec AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
28 AP6255 Datasheet Solder Paste definition AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
29 AP6255 Datasheet 12. Package Information 12.1 Label Label A Anti-static and humidity notice Label B MSL caution / Storage Condition Label C Inner box label . Label D Carton box label . AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
30 12.2 Dimension AP6255 Datasheet AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
31 AP6255 Datasheet Humidity indicator B A Desiccant C C D AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
32 12.3 MSL Level / Storage Condition AP6255 Datasheet NOTE : Accumulated baking time should not exceed 96hrs AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO:
33 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter. This End equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. IMPORTANT NOTE:
In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling The final end product must be labeled in a visible area with the following:
Contains FCC ID: 2AFG6-RK3399. Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. Canada Statement This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
(1) lappareil ne doit pas produire de brouillage;
(2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Caution Exposure:
This device meets the exemption from the routine evaluation limits in section 2.5 of RSS102 and users can obtain Canadian information on RF exposure and compliance. Le dispositif rpond l'exemption des limites d'valuation de routine dans la section 2.5 de RSS102 et les utilisateurs peuvent obtenir des renseignements canadiens sur l'exposition aux RF et le respect. the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;
Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d., qu'ils ont la priorit) des bandes de 5 250 5 350 MHz et de 5 650 5 850 MHz et, dautre part, que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs de RL-EL. for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate. le gain maximal dantenne permis (pour les dispositifs utilisant la bande 5 725-5 825 MHz) doit se conformer la limite de p.i.r.e. spcifie pour lexploitation point point et non point point, selon le cas. The final end product must be labelled in a visible area with the following:
The Industry Canada certification label of a module shall be clearly visible at all times when installed in the host device, otherwise the host device must be labelled to display the Industry Canada certification number of the module, preceded by the words Contains transmitter module, or the word Contains, or similar wording expressing the same meaning, as follows:
Contains transmitter module IC: 22166-RK3399 The module must be installed in Android Module This End equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Cet quipement devrait tre install et actionn avec une distance minimum de 20 centimtres entre le radiateur et votre corps. The end user manual shall include all required regulatory information/warning as show in this manual. This radio transmitter (RK3399) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le prsent metteur radio (RK3399) a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal et l'impdance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. 2.4G:
5G: