WF-Q379-USA1Series IEEE 802.11a/b/g/n/ac 2T2R USB WiFi Module Features Reserving System IEEE Std. 802.11a IEEE Std. 802.11b IEEE Std. 802.11g IEEE Std. 802.11n IEEE Std. 802.11ac Chip Solution Qualcomm 9379-7 Size 18.0mm x 27.0mm x 3.0mm Model Overview WF-Q379-USA1 SMD IEEE 802.11a/b/g/n/ac 866.7Mbps 2.4G/5G 3.3V Sichuan AI-Link Technology Co.,Ltd. Add:
Anzhou,Industrial park,Mianyang,Sichuan Fax : +86-0816-2416943
:
http://www.changhong.com WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module Feedback of customers Confirmation We accept the specification after Confirmed Customer name Customer signature Confirmation Date Please feed back this paper and first paper after your signature by the address,thanks!
ADD Anzhou,Industrial park,Mianyang,Sichuan Factory Sichuan AI-Link Technology Co.,Ltd. Approved Checked Product Designed Model Date WiFi Module WF-Q379-USA1 2018-03-06 Sichuan AI-Link Technology Co.,Ltd. page 2 of 16 WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module Record of Modification No Date of modification Main content of modification Reason of modification 1 2018/03/06 Serial number of modification Confirm Sichuan AI-Link Technology Co.,Ltd. page 3 of 16 WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 1. Introduction WF-Q379-USA1 module design is based on Qualcomm 9379-7 solution, The QCA9379-7 is a highly integrated single chip which has built in a 2x2 dual-band wireless LAN radio. The Module is a highly integrated MAC/BBP and 2.4/5GHz PA/LNA single chip which supports a 866.7Mbps PHY rate. The Module is designed to support standard-based features in the areas of security, quality of service, and international regulations, giving end users the greatest performance anytime and in any circumstance. This documentation describes the engineering requirements specification. 1.1 RF module Overview The general HW architecture for the module is shown in Figure 1. This WLAN Module design is based on Qualcomm QCA9379-7. It is a highly integrated single-chip MIMO(Multiple In Multiple Out) Wireless LAN (WLAN) network interface controller complying with the 802.11 specification and Bluetooth over USB interface. It combines a MAC, a 2T2R capable baseband, and RF in a single chip. An intelligent Wi-Fi coexistence algorithm is implemented to provide the best harmonized Wi-Fi radio performance. 3.3V INPUT 2.4G TX0/RX0 GPIO 5G TX0/RX0 WLAN USB2.0 Interface 2.4G TX1/RX1 WF_ RFIO QCA9379-7 Dixplexer Antenna0 Dixplexer Antenna1 WF_ RFIO 5G TX1/RX1 48MHz Figure 1 WF-Q379-USA1 Block Diagram Sichuan AI-Link Technology Co.,Ltd. page 4 of 16 WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 1.2 Specification reference This specification is based on additional references listed below. _ IEEE Std. 802.11a _ IEEE Std. 802.11b _ IEEE Std. 802.11g _ IEEE Std. 802.11n _ IEEE Std. 802.11ac 1.3 System Functions Table1: General Specification as below:
Qualcomm QCA9379-7 2.4G/5G 802.11a/b/g/n/ac (2x2) WIFI:11b: DBPSK, DQPSK and CCK and DSSS 11a/g: BPSK, QPSK, 16QAM, 64QAM and OFDM 11n: BPSK, QPSK, 16QAM, 64QAM and OFDM 11ac: BPSK, QPSK, 16QAM, 64QAM,256QAM and OFDM 11b: 1, 2, 5.5 and 11Mbps 11a/g: 6, 9, 12, 18, 24, 36, 48 and 54 Mbps 11n: MCS0~15, up to 300Mbps 11ac: MCS0~9, Nss=2, up to 866.7Mbps 32pins , USB 2.0 for WLAN 6-layers design Typical18mm x 27mm x 3mm External Antennas Design 0 to +70
-15 to +45 3.3V +/-10%
Main Chipset Operating Frequency WiFi Standard Modulation Data rates Form factor Host Interface PCB Stack Dimension Antenna Operation Temperature Storage Temperature Operation Voltage Sichuan AI-Link Technology Co.,Ltd. page 5 of 16 WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 2. Mechanical Specification 2.1 Mechanical Outline Drawing Typical Dimension (W x L x H): 18.0mm x 27.0mm x 3.0mm General tolerance: 0.15mm 2.2 Pin definition TOP VIEW Sichuan AI-Link Technology Co.,Ltd. page 6 of 16 WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module Pin Define Description NC NC NC NC GND NC NC NC NC Ground WL_USB_DP WLAN USB2.0 DP Signal WL_USB_DM WLAN USB2.0 DM Signal GND NC NC GND Ground NC NC Ground 1 2 3 4 5 6 7 8 9 10 11 12 Pin 17 18 19 20 21 22 Define NC GND Description NC Ground WL_RF0 Wi-Fi RF port0connect to external antenna GND GND Ground Ground WL_RF1 Wi-Fi RF port1connect to external antenna 23 24 25 26 QOW(GPIO GND GND GND 35) Ground Ground Ground General GPIO single. 27 BT_EN Bluetooth enableactive high BT_RF BT RF Outputconnect to 28 WLAN_EN WLAN enableactive 13 14 BT_WAKE_HOST GND external antenna Ground Bluetooth wakeup the host
(GPIO24) active high 15 HOST_WAKE_BT
(GPIO33) Host wakeup Bluetooth through UARTactive low 29 30 31 GND VDD_3.3V high Ground 3.3V input 3D_SYNC
(GPIO34) Frame sync signals from TV to sync with 3D glass 16 NC NC 32 GND via Bluetooth Ground 2.3 Product Picture 2.4 TOP VIEW BOTTOM VIEW
:
1 PCB 2 3 4 SMT 5 Sichuan AI-Link Technology Co.,Ltd. page 7 of 16 WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 3. Electrical Specification This Specification is based-on conductive DVT testing result. The extreme condition include overall temperature (0,+25,+40) and overall voltage (3.0V,3.3V,3.6V). 3. 1 IEEE 802.11g/a Section:
Items Contents Specification Mode Channel Data rate TX Characteristics 1. Power Levels 1) 16.5dBm Target (For Each antenna port)
@ 11g/6Mbps~24Mbps 2) 16dBm Target (For Each antenna port)
@ 11g 36Mbps 3) 15.5dBm Target (For Each antenna port)
@ 11g 48Mbps 4) 14.5dBm Target (For Each antenna port)
@ 11g 54Mbps 5) 15.5dBm Target (For Each antenna port)
@ 11a/6Mbps~36Mbps 6) 14.5dBm Target (For Each antenna port)
@ 11a 48Mbps 7) 13.5dBm Target (For Each antenna port)
@ 11a 54Mbps 2. Spectrum Mask @ Target Power 1) at fc +/-11MHz 2) at fc +/-20MHz 3) at fc > +/-30MHz 3. Constellation Error(EVM) @ Target Power 1) 6Mbps 2) 9Mbps 3) 12Mbps 4) 18Mbps 5) 24Mbps 6) 36Mbps 7) 48Mbps 8) 54Mbps 4. Frequency Error 1) IEEE802.11g 2) IEEE802.11a RX Characteristics 5. Minimum Input Level Sensitivity(each chain) 1) 6Mbps (PER 10%) 2) 9Mbps (PER 10%) 3) 12Mbps (PER 10%) 4) 18Mbps (PER 10%) IEEE802.11g & IEEE802.11a BPSK, QPSK, 16QAM, 64QAM and OFDM CH1 to CH13 @ 11g CH36 to CH165 @ 11a 6, 9, 12, 18, 24, 36, 48, 54Mbps Min. 14.5 Typ. 16.5 Max. Unit Remark 18.5 dBm 14 16 18 dBm 13.5 15.5 17.5 dBm 12.5 14.5 16.5 dBm 13.5 15.5 17.5 dBm 12.5 14.5 16.5 dBm 11.5 13.5 15.5 dBm
-
-
-
-
-
-
-
-
-
-
-
-25
-30 Min.
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-20
-28
-40
-5
-8
-10
-13
-16
-19
-22
-25 25 30 Typ. Max.
-
-
-
-
-82
-81
-79
-77 dBr dBr dBr dB dB dB dB dB dB dB dB ppm ppm Unit dBm dBm dBm dBm Sichuan AI-Link Technology Co.,Ltd. page 8 of 16 WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 5) 24Mbps (PER 10%) 6) 36Mbps (PER 10%) 7) 48Mbps (PER 10%) 8) 54Mbps (PER 10%) 6. Maximum Input Level (PER 10%) 1) IEEE802.11g 2) IEEE802.11a
-
-
-
-
-20
-30
-
-
-
-
-
-74
-70
-66
-65
-
dBm dBm dBm dBm dBm dBm 3.2 IEEE 802.11b Section:
Items Specification Mode Channel Data rate TX Characteristics 1. Power Levels(Calibrated) 1) 17dBm Target (For Each antenna port)
@1Mbps~11Mbps 2. Spectrum Mask @ Target Power 1) fc +/-11MHz to +/-22MHz 2) fc > +/-22MHz 3. Constellation Error(EVM) @ Target Power 1) 1Mbps 2) 2Mbps 3) 5.5Mbps 4) 11Mbps 4. Frequency Error RX Characteristics 5. Minimum Input Level Sensitivity(each chain) 1) 1Mbps (FER 8%) 2) 2Mbps (FER 8%) 3) 5.5Mbps (FER 8%) 4) 11Mbps (FER 8%) 6. Maximum Input Level (FER 8%) Contents IEEE802.11b DBPSK, DQPSK and CCK and DSSS CH1 to CH13 1, 2, 5.5, 11Mbps Min. 15.5 Typ. 17.5
-
-
-
-
-
-
-25 Min.
-
-
-
-
-10
-
-
-
-
-
-20
-
Typ.
-83
-80
-79
-76
-
Max. Unit Remark 19.5 dBm
-30
-50
-10
-10
-10
-10 25 Max.
-76
-76
-76
-76
-
dBr dBr dB dB dB dB ppm Unit dBm dBm dBm dBm dBm Sichuan AI-Link Technology Co.,Ltd. page 9 of 16 WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 3.3 IEEE 802.11n HT20 Section:
Items Specification Mode Channel Contents IEEE802.11n HT20 @ 2.4G IEEE802.11n HT20 @ 5G BPSK, QPSK, 16QAM, 64QAM and OFDM CH1 to CH13 @ 2.4G CH36 to CH165 @ 5G Data rate (MCS index) MCS0/1/2/3/4/5/6/7/8/9/10/11/12/13/14/15 TX Characteristics 1. Power Levels 1) 16.5dBm Target (For Each antenna port)
@ 2.4G/MCS0~MCS2 2) 16dBm Target (For Each antenna port)
@ 2.4G/MCS3~MCS4 3) 15dBm Target (For Each antenna port)
@ 2.4G/MCS5~MCS6 4) 14.5dBm Target (For Each antenna port)
@ 2.4G/MCS7 5) 15.5dBm Target (For Each antenna port)
@ 5G/MCS0~MCS2 6) 15dBm Target (For Each antenna port)
@ 5G/MCS3~MCS5 7) 14.5dBm Target (For Each antenna port)
@ 5G/MCS6 8) 13.5dBm Target (For Each antenna port)
@ 5G/MCS7 2. Spectrum Mask @ Target Power 1) at fc +/-11MHz 2) at fc +/-20MHz 3) at fc > +/-30MHz 3. Constellation Error(EVM) @ Target Power 1) MCS0 2) MCS1 3) MCS2 4) MCS3 5) MCS4 6) MCS5 7) MCS6 8) MCS7 4. Frequency Error 1) IEEE802.11n HT20 @ 2.4G 2) IEEE802.11n HT20 @ 5G RX Characteristics 5. Minimum Input Level Sensitivity(each chain) 1) MCS0 (PER 10%) 2) MCS1 (PER 10%) 3) MCS2 (PER 10%) 4) MCS3 (PER 10%) 5) MCS4 (PER 10%) 6) MCS5 (PER 10%) Min. 14.5 14 13 Typ. 16.5 16 15 Max. 18.5 18 17 Unit Remark dBm dBm dBm 12.5 14.5 16.5 dBm 13.5 15.5 17.5 dBm 13 15 17 dBm 12.5 14.5 16.5 dBm 11.5 13.5 15.5 dBm
-
-
-
-
-
-
-
-
-
-
-
-25
-20 Min.
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Typ.
-
-
-
-
-
-
-20
-28
-45
-5
-10
-13
-16
-19
-22
-25
-28 25 20 Max.
-82
-79
-77
-74
-70
-66 dBr dBr dBr dB dB dB dB dB dB dB dB ppm ppm Unit dBm dBm dBm dBm dBm dBm Sichuan AI-Link Technology Co.,Ltd. page 10 of 16 WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 7) MCS6 (PER 10%) 8) MCS7 (PER 10%) 6. Maximum Input Level (PER 10%) 1) IEEE802.11n HT20 @ 2.4G 2) IEEE802.11n HT20 @ 5G 3.4 IEEE 802.11n HT40 Section:
Items Specification Mode Channel
-
-
-20
-30
-
-
-
-
-65
-64
-
-
dBm dBm dBm dBm Contents IEEE802.11n HT20 @ 2.4G IEEE802.11n HT20 @ 5G BPSK, QPSK, 16QAM, 64QAM and OFDM CH3 to CH11 @ 2.4G CH38 to CH163 @ 5G Data rate (MCS index) MCS0/1/2/3/4/5/6/7/8/9/10/11/12/13/14/15 Typ. Max. Unit 15.5 17.5 dBm Remark TX Characteristics 1. Power Levels (Calibrated) 1) 15.5dBm Target (For Each antenna port)
@ 2.4G/MCS0~MCS2 2) 15dBm Target (For Each antenna port)
@ 2.4G/MCS3~MCS4 3) 14dBm Target (For Each antenna port)
@ 2.4G/MCS5~MCS6 4) 13.5dBm Target (For Each antenna port)
@ 2.4G/MCS7 5) 14.5dBm Target (For Each antenna port)
@ 5G/MCS0~MCS2 6) 14dBm Target (For Each antenna port)
@ 5G/MCS3~MCS5 7) 13.5dBm Target (For Each antenna port)
@ 5G/MCS6 8) 12.5dBm Target (For Each antenna port)
@ 5G/MCS7 2. Spectrum Mask @ Target Power 1) at fc +/-21MHz 2) at fc +/-40MHz 3) at fc > +/-60MHz 3. Constellation Error(EVM) @ Target Power 1) MCS0 2) MCS1 3) MCS2 4) MCS3 5) MCS4 6) MCS5 7) MCS6 8) MCS7 4. Frequency Error 1) IEEE802.11n HT20 @ 2.4G 2) IEEE802.11n HT20 @ 5G RX Characteristics Min. 13.3 13 12 15 14 17 16 dBm dBm 11.5 13.5 15.5 dBm 12.5 14.5 16.5 dBm 12 14 16 dBm 11.5 13.5 15.5 dBm 10.5 12.5 14.5 dBm
-
-
-
-
-
-
-
-
-
-
-
-25
-20 Min.
-
-
-
-
-
-
-
-
-
-
-
-
-
-20
-28
-45
-5
-10
-13
-16
-19
-22
-25
-28 25 20 Typ. Max. dBr dBr dBr dB dB dB dB dB dB dB dB ppm ppm Unit Sichuan AI-Link Technology Co.,Ltd. page 11 of 16 WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 5. Minimum Input Level Sensitivity(each chain) 1) MCS0 (PER 10%) 2) MCS1 (PER 10%) 3) MCS2 (PER 10%) 4) MCS3 (PER 10%) 5) MCS4 (PER 10%) 6) MCS5 (PER 10%) 7) MCS6 (PER 10%) 8) MCS7 (PER 10%) 6. Maximum Input Level(PER 10%) 1) IEEE802.11n HT20 @ 2.4G 2) IEEE802.11n HT20 @ 5G
-
-
-
-
-
-
-
-
-20
-30
-
-
-
-
-
-
-
-
-
-
-79
-76
-74
-71
-67
-63
-62
-61
-
-
dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm 3.5 IEEE 802.11ac Section:
Items Specification Mode Channel Data rate (MCS index) TX Characteristics 1. Power Levels (Calibrated) 1) 15.5dBm Target (For Each antenna port)
@VHT20 MCS0~MCS2 2) 15dBm Target (For Each antenna port)
@VHT20 MCS3~MCS5 3) 14.5dBm Target (For Each antenna port)
@VHT20 MCS6 4) 13.5dBm Target (For Each antenna port)
@VHT20 MCS7 5) 12.5dBm Target (For Each antenna port)
@VHT20 MCS8 6) 14.5dBm Target (For Each antenna port)
@VHT40 MCS0~MCS2 7) 14dBm Target (For Each antenna port)
@VHT40 MCS3~MCS5 8) 13.5dBm Target (For Each antenna port)
@VHT40 MCS6 9) 12.5dBm Target (For Each antenna port)
@VHT40 MCS7 Contents IEEE802.11ac BPSK, QPSK, 16QAM, 64QAM ,256QAM and OFDM CH36 to CH165 VHT20 CH38 to CH163 VHT40 CH42 to CH157 VHT80 MCS0/1/2/3/4/5/6/7/8/9 Min. Typ. 13.5 15.5 13 15 12.5 14.5 11.5 13.5 10.5 12.5 12.5 14.5 12 14 11.5 13.5 10.5 12.5 Max. 17.5 17 16.5 15.5 14.5 16.5 16 15.5 14.5 13.5 12.5 15.5 Unit Remark dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm 10) 11.5dBm Target (For Each antenna port)
@VHT40 MCS8 11) 10.5dBm Target (For Each antenna port)
@VHT40 MCS9 9.5 8.5 12) 13.5dBm Target (For Each antenna port) 11.5 11.5 10.5 13.5 Sichuan AI-Link Technology Co.,Ltd. page 12 of 16 WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module
@VHT80 MCS0~2 13) 13dBm Target (For Each antenna port)
@VHT80 MCS3~5 14) 12.5dBm Target (For Each antenna port)
@VHT80 MCS6 15) 11.5dBm Target (For Each antenna port)
@VHT80 MCS7 16) 10.5dBm Target (For Each antenna port)
@VHT80 MCS8 17) 9.5dBm Target (For Each antenna port)
@VHT80 MCS9 2. Spectrum Mask @ Target Power 1) at fc +/-11MHz /20MHz/30MHz 2) at fc +/-21MHz /40MHz/60MHz 3) at fc +/-41MHz /80MHz/120MHz 3. Constellation Error(EVM) @ Target Power 1) MCS0 2) MCS1 3) MCS2 4) MCS3 5) MCS4 6) MCS5 7) MCS6 8) MCS7 9) MCS8 10) MCS9 4. Frequency Error RX Characteristics 5. Minimum Input Level Sensitivity(each chain) 1) MCS0 (PER 10%) 2) MCS1 (PER 10%) 3) MCS2 (PER 10%) 4) MCS3 (PER 10%) 5) MCS4 (PER 10%) 6) MCS5 (PER 10%) 7) MCS6 (PER 10%) 8) MCS7 (PER 10%) 9) MCS8 (PER 10%) 10) MCS9 (PER 10%) 6. Maximum Input Level(PER 10%) 11 13 10.5 12.5 9.5 8.5 7.5
-
-
-
-
-
-
-
-
-
-
-
-10 Min.
-
-
-
-
-
-
-
-
-
-
-30 11.5 10.5 9.5
-
-
-
-
-
-
-
-
-
-
-
-
Typ.
-
-
-
-
-
-
-
-
-
-
-
15 14.5 13.5 12.5 11.5
-20
-28
-40
-5
-10
-13
-16
-19
-22
-25
-27
-30
-32 10 Max. VHT20 VHT40 VHT80
-82
-79
-77
-74
-70
-66
-65
-64
-59
-57
-79
-76
-74
-71
-67
-63
-62
-61
-56
-54
-
-76
-73
-71
-68
-64
-60
-59
-58
-53
-51 dBm dBm dBm dBm dBm dBr dBr dBr dB dB dB dB dB dB dB dB dB dB ppm Unit dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm Sichuan AI-Link Technology Co.,Ltd. page 13 of 16 WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 4. Software Requirements The driver supports the following operating systems: Linux, Microsoft Windows XP, Vista and Win7. Mfg. software tool is QDART. 5. Antenna matching The BT RF ANT0 and ANT1 Pin connect to antenna, please refer to design demand a). b). PIN12,PIN19PIN22RF50 c). L1, L2, C1 6. Key component List
/
QCA9379-7 QFN Qualcomm 1 2 PCB JUI7.820. 0317 FR-6,4LAY 3 4 SMD2520-48M 1608 Hosonic TXC ACX TDK Sichuan AI-Link Technology Co.,Ltd. page 14 of 16 WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 7. Packaging Information:
Sichuan AI-Link Technology Co.,Ltd. page 15 of 16 WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 3 1. 2. 600153000/;
3. 378mm*297mm*370mm355mm*355mm*50mm;
4. 2g261;
5. CVTE;
Sichuan AI-Link Technology Co.,Ltd. page 16 of 16 FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Please notice that if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains FCC ID: 2AFG6-WF-Q379-USA1 any similar wording that expresses the same meaning may be used. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The module is limited to OEM installation ONLY. The OEM integrator is responsible for ensuring that the end-user has no manual instruction to remove or install module. The module is limited to installation in mobile or fixed application. A separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and difference antenna configurations. There is requirement that the grantee provide guidance to the host manufacturer for compliance with Part 15B requirements Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01 2.2 List of applicable FCC rules Part 15.247 and Part 15.407 2.3 Specific operational use conditions The module is limited to installation in mobile or fixed application. A separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and difference antenna configurations. 2.4 Limited module procedures Not applicable as this is not a limited modular. 2.5 Trace antenna designs Not applicable as there is no trace antenna design in this modular. 2.6 RF exposure considerations For the end host, the antennas used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. 2.7 Antennas For BT&LE Ant. Brand P/N Antenna Type Connector Gain (dBi) 1 TB-SR-41Y Dipole N/A 2.76 For WIFI 2.4G &5G Ant. Brand Model Name Antenna Type Connector Gain (dBi) 1 2 N/A N/A PCB PCB N/A N/A 3.95(2.4G) 3.33(5G) 3.95(2.4G) 3.33(5G) 2.8 Label and compliance information Host product manufacturers are required to provide a physical or e-label stating Contains FCC ID: 2AFG6-WF-Q379-USA1 with their finished product. 2.9 Information on test modes and additional testing requirements Test modes should take into consideration different operational conditions for a stand-alone modular transmitter in a host, as well as for multiple simultaneously transmitting modules or other transmitters in a host product. 2.10 Additional testing, Part 15 Subpart B disclaimer This modular transmitter is only FCC authorized for FCC Part 15.247&15.407 as listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed.