1GE+3FE+WIFI EPON ONU
Quick Installation Guide
V2.0
Aug. 13, 2019
P01.030488
2 1GE+3FE+WIFI EPON ONU Quick Installation Guide_V2.0
1. Indicator and Interface Description
1.1 Product Picture
Figure 1 1GE+3FE+WIFI EPON ONU
1.2 Application Chart
Figure 2 Application Chart
1.3 Panel Lights
Figure 3 Panel Lights
3 1GE+3FE+WIFI EPON ONU Quick Installation Guide_V2.0
LED
Mark
Status
Description
Power
POWER
The device is powered up.
The device is powered down.
Registration
PON
Device is not registered to the PON system.
The device is registered to the PON system.
Optical signal
LOS
Blink Device registration is incorrect.
Blink
Device does not receive optical signals.
Off
Device has received optical signal.
WiFi
WiFi
On WiFi is working
Off WiFi is not working
WPS
ON WIFI allow one key join
Pair
LAN1
LAN2
LAN3
LAN4
Interface
Port connection exception or not connected.
Port is connected properly (LINK).
Blink Port is sending or/and receiving data (ACT).
Table 1 Panel Lights
On
Off
On
Off
On
Off
1.4 Interface/button Panel
Figure 4 Interface/button Panel
Function
Connect to OLT by SC type fiber connector, single mode optical fiber
cable.
Connect PC or other devices with Ethernet port by Cat5 cable, RJ-45
connector.
Press RST button over 10 seconds, onu restores factory default and
reboot.
Connect with power adapter. DC 12V, 1A.
Press down WiFi pair button to begin pairing.
Press down WiFi turn on/off button to enable/disable WiFi function.
Table 2 Interface/button Panel
Name
PON
LAN
RST
Pair
WiFi
POWER
4 1GE+3FE+WIFI EPON ONU Quick Installation Guide_V2.0
2. Packing List
Contents
Quantity
Contents
Quantity
EPON ONU
Installation Guide
1 pcs
1 pcs
Power adapter
1 pcs
3. Certification
4. Hardware Installation
Installation Environment Requirements
ONU equipment must be installed in the interior, and to ensure the following conditions:
Confirmation at the ONU installation at sufficient space to facilitate cooling machine.
ONU suitable operating temperature of -5 ℃ ~ 55 ℃, humidity 10% to 90%.
Device workplace should avoid radio transmitters, radar stations, and high-frequency
interference from power equipment.
Installed on the desktop
Equipment Installation
1.
Place the ONU on a clean bench, this installation is relatively simple, you can observe the
following operation:
Ensure the smooth workbench.
Around the device enough space for heat dissipation.
Do not place objects on the device.
2. Mounted on the wall
Observation ONU equipment chassis two cruciform recess, in accordance with the
position of the groove, installed two screws in the wall.
The original selected two mounting screws gently snap into recesses aligned.
Slowly let go, so that the device under the support of the screw hanging on the wall.
3. Connect fiber, network cable and power adapter to the corresponding interfaces, and turn
on the power of product.
5 1GE+3FE+WIFI EPON ONU Quick Installation Guide_V2.0
FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any inte rference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interferenceto radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator and your body.