775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: sales.eaw@us.bureauveritas.com Modular Approval Declaration Letter Revision History To From Reason for Amendment (current / obsolete) Initial Release (Obsolete) Added IC Modular Letter (Obsolete) Add LMA and MA option (Obsolete) Revised per RSS Gen issue 3.0 (Obsolete) Removed Foot(2) (obsolete) Adding New note per KDB996369 D01 V01R03
(obsolete) Updated company template & Added text box (obsolete) Updated modular requirement (obsolete) Updated template to meet RSP 100 issue 10 (obsolete) Updated template to meet RSP 100 issue 11 (obsolete)) Revised the Modular Requirement statements
(obsolete) Updated template with BV logo (current) 1.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 Approved Date Dec-04-2006 Feb 16 2009 April 14 2010 Jan 12 2011 July 19 2011 August 29 2011 Jan-31-2012 Sept 05 2014 Nov 20 2014 March 19 2015 July 28, 2016 June 26, 2019 SCS-F26 Modular Approval Letter Page 1 of 3 Rev 12.0
(Guangzhou Vensi Intelligent Technology Co., Ltd.)
(Date) 2020-12-28
(Product name) FCC ID: 2AR6I-ZE3221X , is seeking FCC Authorization as a The EUT meets the requirements for as detailed in KDB 996369. Compliance to each of the requirements is described below:
Item Single Modular Transmitter /
Single Modular Approval /
Modular requirement Single Limited Modular Transmitter (Please check one) Single Limited Modular Approval (Please check one) Yes No Please provide a detailed explanation if the answer is No. No Products belong to restricted modules rather than full module certification Have its own RF shielding Have buffered modulation/data inputs (if such inputs are provided) The modular transmitter must have its own power supply regulation. Meet the antenna requirements of section 15.203 Be tested in a stand-alone configuration, i.e., the antenna, AC or DC power and data input/output lines must be connected to the module but, the module must not be inside another case during testing. Be labeled with its own FCC ID number, and if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. The modular transmitter is manufactured so that the user can not influence the operation of the transmitter that will operate outside of the scope of the regulations. Address compliance with the Commission`s RF exposure limits in Sections 1.1310 and 2.1093. YES YES YES YES YES YES YES 1 2 3 4 5 6 7 8 Note:
(1) LMA may be granted when one or more of the requirements in the table above cannot be demonstrated. LMA will also be issued in those instances where applicants can demonstrate that they will retain control over the final installation of the device, such that compliance of the end product is assured. In such cases, an operating condition on the LMA for the module must state that the module is only approved for use when installed in devices produced by a specific manufacturer. When LMA is sought, the application for equipment certification must specifically state how control of the end product into which the module will be installed, and will be maintained, such that full compliance of the end product is always ensured.
(2) Please provide Clear and specific instructions describing the conditions, limitations and procedures for third-parties to use and/or integrate the module into a host device.
(3) For non-Software Defined Radio transmitter modules where software is used to ensure compliance of the device, technical description of how such control is implemented to ensure prevention of third party modification must be provided (see KDB 594280). Note 1: Compliance of a module in its final configuration is the responsibility of the applicant. A host device will not be considered certified if the instructions regarding antenna configuration provided in the original description, of one or more separately certified modules it contains, were not followed. Example: A separately certified low-power transceiver module using Bluetooth technology which is housed in a desktop computer, laptop or peripheral does not require the overall system to be recertified, if the desktop computer, laptop or peripheral, as a stand-alone unit, complies with all applicable technical standards. Clients signature Clients name & title: zengfanman/manager Contact information / address: No.19 Huangqi Shan Road, Yonghe Development Zone, Whampoa District, Guangzhou SCS-F26 Modular Approval Letter Page 2 of 3 Rev 12.0
(Guangzhou Vensi Intelligent Technology Co., Ltd.) LMA Declaration Letter We, (applicant name), declare that we will retain control over the final installation of the device,
(FCC ID: 2AR6I-ZE3221X ) so that compliance of the end product is assured. In such cases, an operating condition on the LMA for the module must be only approved for use when installed in devices produced by a specific manufacturer. Clients signature Clients name & title: zengfanman/manager Contact information / address: No.19 Huangqi Shan Road, Yonghe Development Zone, Whampoa District, Guangzhou SCS-F26 Modular Approval Letter Page 3 of 3 Rev 12.0