2D Barcode Scanner Quick Start Guide 1 Scanner overview 2 Cable plug&Unplug 3 Cable connection guide LED Indicator Buzzar Scanning window Bluetooth 2D Contents: Barcode Scanner Cradle Quick Start Guide USB Cable WNI-6214 Scanner Cradle LED Indicator Trigger Buon Plug as picture above No.:1230257001 v1.0 4 Charging method Cardle Note: Product appearance depends on goods 5 Scanning Angle 65
-
6 5 90 0 2D Image Scanner
-90 121311113 The aiming beam should be centered over the bar code, but it can be posioned in any direcon for a good read. Press the buckle click, then pull out the cable Descripon Light LED Status Scanner Green light on Power on/ Working normally Red light blinks Green light blinks once Red light on Blue light on Green light on Green light blinking Pairing match Upload successfully Low baery Charging normal Charging complete Pairing unsuccessful Cradle Blue light blinks once Blue light on Blue light blinks Descripon Uploaded successfully Working normally Pairing match Buzzer Scanner beeper mode Short two beeps Short one beep Short once long beep Data upload failed Pairing successfully Descripon Scan and transmit successfully Craddle beeper mode Four Beeps Short one beep Descripon power On Scan and transmit successfully Pairing Guide Connent to dongle First step: Insert the cradle as above picture. Second step: Aer insert the cradle , Place the scanner near the cradle Wait for scanner pairing to complete Pairing Guide Connent to Phone First step: Iniang scanner Pairing Guide
...Connent to Phone Third step: Pairing scanner to TABLET/PC Second step: Enabling Bluetooth on TABLET/PC iOS:
- Tap Sengs> Bluetooth
- Make sure Bluetooth is switched on Microso Windows:
- Go to Sengs > Devices > Bluetooth
- Make sure Bluetooth is switched on Android:
- Go to Sengs> Connecons> Bluetooth
- Make sure Bluetooth is switched on A:To start pairing, Press the buon, wake up the scanner and the red pairing indicator lights start to ash B:The scanner name: Barcode Scanner iOS:
-Tap the device name to nish pairing Microso Windows:
- Click on the device name then click "Pair Android:
- Tap on the device name to nish pairing The scanner beeps rapidly 2 mes indicang that the pairing is nished. If successful,'Connected' appears beside the device name in the bluetooth devlice list. Pairing Guide If pairing is unsuccessful If the device does not say "Connected"
the pairing has not been successful. To try again:
ios:
- Tap the beside the device name then
"Forget this device"
Microso Windows:
- Select device then click "Remove device Android:
- Tap on beside the device name then
"Unpair Now repeat steps Connent to Phone. Note: The connecon will automacally disconnect when the scanner turns o but will automacally reconnect aer a few seconds when turned back on. Using the Scanner 1,Open the soware applicaon you would like to use the Scanner with. 2,Select the input eld in which you would 3,Turn the scanner on by clicking the Trigger buon, and wait for it to connect (green &
solid red lights). 4,Point the scanner at the barcode and press and hold the buon to capture the barcode. You will hear a solid beep when the number is scanned successfully. M C 5 e 5 1 c n e d is t a d o c e s t d e B Troubleshooting
...Troubleshooting Sleep Time Setting Q: The scanner is in pairing phone mode and I cannot see it in my bluetooth device list on my Tablet/ PC. Q: The scanner is unresponsive. Inially the device may be labelled "keyboard" in the devices list. This will eventually change to "Barcode Scanner Q: How do I disconnect then re-connect the scanner to my system (tablet device or PC)? This can be used to reconnect to a dierent system or if there are problems pairing. 1. Open your system's Bluetooth sengs and nd the VIN Scanner in the device list. 2. Tap the scanner in the list & remove or forget it. Turn Bluetooth o then on again. The system will 3. search for devices again. 4. Connue with the pairing steps Check that the scanner is fully charged. Make sure it's in the right mode Next, remove or forget the system as described above then try pairing gain. Q: Connecon not established aer turning the scanner on even though previously paired. Wait for the scanner to turn o. Turn it on again with the Trigger buon and wait a few seconds for the scanner to automacally reconnect to your system. Q: The scanner isn't reading even though it is on and the connecon established. Try moving the scanner further away from the barcode or adjusng the scan angle. Try scanning a barcode into a Notepad applicaon to see if it now reads successfully. Check that the scanner is paired to the system(tablet or PC) you are actually using and not another nearby device. The sleep me means the me between the last operaon move and auto turn o the scanner. User able to scan the corresponding bar code of the sleep me which is needed to accomplish the sleep me seng. Set up process Scan the bar code ofSleep Time. Scan one of the bar code below as sleep me. Sleep Time 7.5min 60S 22min 45min Scan the bar code of Exit and Save. Exit and Save FCC STATEMENT :
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. RF warning statement:
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.