SOLA Level box 1. PRODUCT OUTLOOK NO.82485 SPECIFICATION 2. PRODUCT DESCRIPTION SOLA LEVEL BOX COULD DO LEVEL MEASURING AND RELATIVE MEASURING, WITH HOLD, FLIP OVER READING, BACKLIGHT AND SOUNDING FUNCTION. SMALL SIZE, EASY FOR CARRYING, GOOD FOR MANY APPLICATIONS. 3. PRODUCT FEATURES 3.1 MEASURING UNIT: , %, mm/m, in/ft 3.2 RESOLUTION:0.05/ 0.1could choose by APPdefault is 0.1 3.3 Accuracy: 0&900.051 to 890.2 3.4 Measuring range4*90 3.5 Backlight: When turn on, white backlight is on 3.6 Number changing or any press button will active the backlight. 1min no movement, backlight will automatically shut off. 3.7 Hold functionShort pressHOLDbutton at any angle will hold the measurement, symbol HOLDwill show on the display. 3.8 Relative measuringcustomer could set relative 0 at any angle. 3.9 Auto shut off in 3 minutes if no operation or number not move. 3.10 0/45/90sounding function: different frequency sounding for closing to 0/45/90. When angle close to 0/45/90 from 1.55to 0.8(1time/second),from 0.75-0.32times/secondfrom 0.25-0.054times/second0.00continue sounding. Different voice at anti-clockwise direction and clockwise direction. Different sound in situation the right side is not inclined compare in the situation the left side is not inclined default sound is OFF 3.11 PowerDC1.5V(AA1 ) 3.12 Full view LCD 3.13 Flip over display when over 90 degree. 3.14 Battery life: 80 hours(bluetooth on, backlight off),65 hours(bluetooth on, backlight on)The result is been calculated base on battery capacity is 2500mAH, we will do the real calculation when getting the mass production battery 3.15 Dropping resistantAll function running okay after 2 meters dropping test. 3.16 Buetooth functionAfter installing the battery, device will on, bluetooth will on automatically at the same time. When connected, device will continue sending the current value to the APP. Bluetooth is ON at every time when product is on 3.17 BLE IDSOLA_Go!_smart_00500(unique ID on each product, but not continue number). When device be connected in successful, there is no chance for connect with other ones in the same area. 3.18 APP could show the displayed value, APP could operate the product. 3.19 After connecting one time, cell phone will be automatically be connected later. 3.20 Bluetooth protocol4.0BLE
? Bluetooth transfer distance 10meter in barrier free area, other bluetooth device around will not effect this device. 3.21 Warning out of tolerance longitudinally: when measuring near 0and 90, if the longitudinal axle ( fore-and-aft direction) inclination exceeds 30, it will display - - - - - - which means substantial deviation in the measurement and no accurate value can be provided. 3.22 1.1V low voltage warning.(battery sign will keep ashing when reach 1.1V. The product could keep run 2 hours since 1.1V until power off automatically) 3.23 Default state when installing battery/onABS statusunit backlight onsounding off, bluetooth on. ABS didnt be shown on the display 4. PRODUCT TECHNIC DATA 4.1 Temperature:
4.1.1 Working temperature -10C (14F) to 50C (122F) 4.1.2 Storage temperature or shipping temperature: -20C (-4F) to 60C (140F) 4.2 Working humidity85%
4.3 (EMC)Class II 4.4 IP levelIP54 4.5 FCC certicate 4.6 REACH, ROHS will be supplied by GEMRED self-declaration 5. PRESS BUTTON OPERATION:
ON/OFF Button At off status, short press to turn on the device. At on status, press button for 2seconds to turn off the device. HOLD Button Short press it to enter/exit the HOLD mode, under HOLD mode, LCD will have symbol HOLD be displayed. Long press(2 seconds) HOLD button to enter the INC mode and set relative ZERO, long press (2 seconds) it again to return to ABS mode. MODE Button Short press it to convert between unit, %, mm/m, in/ft Long press (2 seconds) it to turn on/off the sounding functionunder sounding function, LCD will have sound symbol be displayed. ON/OFF Button + MODE Button Press ON/OFF Button and MODE Button at the same time could enter the mode to choose the resolution 0.1or 0.05. RemarksDefault resolution is 0.1next time turn on the device will keep in default setting no matter which resolution been chosen last time. CalibrationCalibration already been done at facotry, customer no need to do the calibration before using. If you want to calibrate again, you could follow the following steps. aLevel calibration a1ZERO point calibration At on status, long press (2 seconds) ON/OFF and HOLD at the same time to enter the calibration. 1Put the device at a at surface, at on status, long press(2 seconds) the ON/OFF and HOLD button at the same time to enter the calibration and -1- will be displayed. As following picture. 2Short press ON/OFF button-1- ashingkeep the device no movement until-2- be displayed. As following picture. 3Turn 180of the device at the same position. As following picture. 4Short press ON/OFF button-2- ashing, keep the device no movement until the device automatically exit the calibration status, calibration is done. a2180position calibration 1Put the device at a at surface, at on status, long press(2 seconds) the ON/OFF and HOLD button at the same time to enter the calibration and -1- will be displayed. As following picture.
(2) Short press ON/OFF button-1- ashingkeep the device no movement until-2- be displayed. As following picture. 3Turn 180of the device at the same position. As following picture.
(4)Short press ON/OFF button-2- ashing, keep the device no movement until the device automatically exit the calibration status, calibration is done. time to enter the calibration and -1- will be displayed. See picture 1. bVertical position calibration 1Put the device at a at surface, at on status, long press(2 seconds) the ON/OFF and HOLD button at the same 2Short press ON/OFF button-1- ashingkeep the device no movement until-2- be displayed. See picture 2.3Turn 180of the device at the same position,See picture 3.4. 4Short press ON/OFF button-2- ashing, keep the device no movement until the device automatically exit the calibration status, calibration is done. 6. LCD DISPLAY SYMBOL :
Right end is higher than left endLCD will display Left end is higher than right end, LCD will display
. No arrow be displayed at 0 point. 7. PRODUCT FUNCTIONS:
Preparation before usages: to open the battery compartment on the back of the product, insert one piece AA alkaline battery into the compartment and then close the battery compartment. 7.1 Absolute measurement:
Long press HOLD Button to enter the ABS mode, LCD will display the measured value between the measuring surface and the earth level. 7.3 HOLDING functionDuring measuring period, short press HOLD button could freeze the measuring value and the LCD will show HOLD symbol, short press it again could exit the HOLDING function.(see following picture) 7.2 Relative measurement: Put the device on the rst measured surface, long press HOLD button to enter INC mode and LCD will display 0.0and symbol INC be displayed, put the device to another measured surface, the LCD will show the angle between these two measured surfaces.(as the following picture) 7.4 BacklightPress any button or number changing all could active the backlight, no movement or press in 1 minute the backlight will off automatically. 7.5 SOUND functionThe device has sound reminding function. Long pressMODE button to enter or exit SOUND function(LCD has sound symbol be displayed). Under SOUND funciton, at 04590will have different frequency sound reminding. (For details pls check no. 3.10) 7.6 Inclination measurementshort push on the button of MODE may convert between , mm/m, % and in/ft and get the corresponding symbol at the same time. mm/mwhen the angle is between 0 and 45, H=L tg; when the angle is between 45and 90, H=L * 1/tg. L=1000mm. e.g.: when =30 , H=L* tg30(calculated at the resolution of 0.1mm/m)=577.0mm/m Remarks:mm/m is calculated from , the result is the round data.
%when the angle is between 0~45, H=L*tg when angle is between 45~90,H=L*1/tg. Of which L=100mm. E.g.: when =30, H=L tg30calculated according to the resolution of 0.1 %=57.7%
Remarks: % is calculated from , the result is the round data. in/ftWhen the angle is between 0~45, H=INT(1000*L* tg/125)*125/1000when the angle is between 45~90, H=INT(1000*L 1/tg/125)*125/1000. Of which L=12in. E.g.: when =30, H=L tg30calculated according to the resolution of 1/8 in/ft=6 7/8 in/ft 8. PRODUCT MAGNET The product will not fall off when stick upside down on iron or steel plates. Magnet will not effect the display, when shipping, the magnet also will not effect the other product which been shipped together. 9.PRODUCT MATERIAL, COLOR AND SIZE Press button: Rubber Print of ON/OFF button may will be red Printing on press buttonWhite Red plastic partRAL3020 or refer to SOLA sample. Black plastic partRAL9017 Plastic housingABS Measuring surfacePA66+50% Fiberglass Surface roughness of plastic partVDI 3400 - 27 Appearance size80*55*27mm Screwsself-cutting Torx screw for plastic housing(COLOR BLACK) Put sticker mold and the parts out of the mold will be only used for SOLA on the mold. No QC sticker on the product. S/N number should put on the battery compartment 10. TROUBLE SHOOTING 11. OTHERS 11.1 The copyright bellows to our company. No copy is permitted. Caution: The user is cautioned that changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.