Re:
Certification for Hafele DMT 32 Transmitter Model: DMT 32 FCC ID: PW3107 USER'S MANUAL INFORMATION
(PRELIMINARY) The User's Manual is in preparation. The following material will be contained in the manual:
FCC ID: PW3107 CANADA: to be provided by IC This device complies with Part 15 of the FCC Rule s and with RSS-210 of Industry Canada. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. WARNING: Changes or modifications not expressively approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the Increase the separation between the equipment and receiver. receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Technical information Mounting instructions All safes are supplied in the basic method of operation. In this method of operation, locking authorisations can be allocated to personnel keys directly at the safe with a special programming key stick
(green). The locking authorisations are withdrawn again directly at the safe with a clearing key stick (red). Guest keys are authorised via the software Hotel. The configuration takes place when the system is initiated. Technical data:
weight TM3 TM4 thickness of steel material thickness of front plate and door safety level number of locking bolts 13 kg 19 kg, with removable shelf (sheet steel) 2 mm, single walled 6 mm A according to VDMA, norm 24992 2 engl. 9 Mounting instructions Supply schedule l safe l safe TM4: removable shelf (sheet steel) l four Mignon-1,5-V-batteries (already inserted) l battery holder TRE emergency power supply Installation The safe is designed for installation into furniture. 1 2 3 ca. 1,2 m 1 2 3 end plate (19 mm thick) safe base plate (35 to 40 mm thick) 10 engl. Mounting instructions 173 128 248 318 280 29 Built-in dimensions of safe TM3 278 170 295 398 300 29 Built-in dimensions of safe TM4 1. Glue and screw fix the base plate to the side panels of the cabinet at approx. 1.2 m above the cabinet base. 2. Glue and screw fix the end plate to the side panels of the cabinet above the base plate. Insert the safe. 3. Screw fix the safe in the cabinet 1. For screw fixing to the rear panel of the cabinet: from the inside of the safe, push two screws through the 10 mm drillings in the back panel of the safe and screw fix the safe to the cabinet. 2. For screw fixing to the base plate: from the inside of the safe, push four screws through the 8 mm drillings in the base of the safe and screw fix the safe to the base plate. engl. 11 Initiation Mounting instructions Allocation of programming and clearing key stick In the basic method of operation, the programming and clearing key sticks must be allocated during the first initiation. Avoid misuse of the electronic keys by unauthorised persons: keep the programming and clearing key sticks in a safe place, as these will allow allocation of locking authorisations to an electronic key. 1. Have the green programming key stick and the red clearing key stick ready. 2. Push the white button on the display of the safe. the green indicator (LED) flashes for a few seconds. 3. Hold the green programming key stick in front of the display, whilst the green LED flashes. The red indicator (LED) is illuminated once as confirmation of the allocation process, afterwards it flashes. 4. Hold the red clearing key stick in front of the display, whilst the red LED flashes. The green indicator (LED) flashes for a few seconds. The safe switches off automatically. If errors occurred during the allocation:
switch the safe back on.
re-allocate the programming and clearing key stick. If errors re-occur:
contact your Dialock sales office. 12 engl. Brief operating instructions for the basic method of operation Mounting instructions Allocation of locking authorisations to a personnel key 1. Push the white button on the display. The red indicator (LED) is illuminated. 2. Hold the green programming key stick in front of the display. The green indicator (LED) flashes. 3. Hold the personnel key to be allocated in front of the display within 5 seconds. The green indicator (LED) is illuminated briefly. The access authorisation for the personnel key to be allocated has been given. 4. Remove the allocated personnel key. The safe switches off automatically. If the red indicator (LED) is illuminated, the attempt was unsuccessful:
repeat the allocation of locking authorisations. 5. Hold the next personnel key to be allocated in front of the display in intervals of 5 seconds. Withdrawal of locking authorisations from the personnel key 1. Push the white button on the display. The red indicator (LED) is illuminated. 2. Hold the red clearing key stick in front of the display. The red indicator (LED) flashes. 3. Hold the personnel key to be deleted in front of the display. The red indicator (LED) is illuminated briefly. The locking authorisation is withdrawn. The safe switches off automatically. Withdrawal of locking authorisations from all personnel keys When a personnel key is lost and should no longer have any locking authorisations, all personnel keys have to be deleted at the safe. Afterwards, all respective personnel keys re-allocated with locking authorisations. 1. Push the white button on the display. The red indicator (LED) is illuminated. engl. 13 Mounting instructions 2. Hold the red clearing key stick in front of the display. The red indicator (LED) flashes.. 3. Hold the green programming key stick in front of the display. The red indicator (LED) is illuminated briefly. The locking authorisations are withdrawn. 4. Re-allocate locking authorisations to all personnel keys, which need to retain these. Change of batteries When the batteries are weak, the red and green indicators (LED) flash alternately once the safe is switched on. The smooth operation of the safe is only guaranteed, if the batteries are replaced immediately. 1. Open the battery compartment on the inside of the safe door with a 2. cross slot screw driver. Insert four new mignon-1,5-V-batteries (cat. no. 910.54.980). Make sure, the polarity is correct!
3. Close and screw fix the battery compartment. Emergency opening 1. Connect the battery holder TRE emergency power supply on the underside of the display. 2. Hold the valid key in front of the display. 3. Open the safe door. 4. Change the batteries. 14 engl. Mounting instructions Operation Guest keys are allocated automatically, when locking the safe for the first time. Up to four guest keys can be allocated per safe. Locking of the safe 1. Close the safe door. 2. Push the white button on the display. The green indicator (LED) is illuminated. 3. Hold the electronic key in front of the safe. The green and the red indicators (LED) flash alternately and the bolts move audibly. The red indicator (LED) is illuminated. The safe is locked. Opening of the safe 1. Push the white button on the display. The red indicator (LED) is illuminated. The safe is switched on. 2. Hold the electronic key in front of the safe. The green and red indicators (LED) flash alternately and the bolts move audibly. The green indicator (LED) is illuminated. 3. Open the safe door. engl. 15 Montaganleitung 732.29.108 Der Nachdruck der Montageanleitung, auch auszugsweise, oder die Nachahmung der Abbildungen und Zeichnungen sowie die Nachahmung der Gestaltung sind verboten. Fr Druckfehler und Irrtmer, die bei der Erstellung der Montageanleitung unterlaufen sind, ist jede Haftung ausgeschlossen. Liefermglichkeiten und technische nderungen vorbehalten. Stand 06.00 Mounting instructions 732.29.108 The reprint of the mounting instructions, even extracts, or copying of the illustrations and drawings as well as copying of the layout are prohibited. No liability is accepted for printing errors or errors occurred during the creation of the mounting instructions. We reserve the right for technical changes and changes of availability. Status 06.00 Instructions de montage 732.29.108 Il est interdit de reproduire les instructions de montage ou den imprimer des extraits, den copier des illustrations et des dessins ou den imiter la prsentation. Il ne sera assum aucune responsabilit quant aux erreurs et fautes pouvant rsulter de limpression de ces instructions de montage. Tous les droits de possibilits de livraison et de modifications techniques sont rservs. Version du 06.00 Istruzioni di montaggio 732.29.108 E' vietata la copia delle istruzioni di montaggio, anche soltanto parziale, oppure delle raffigurazioni e die disegni come anche la riproduzione del layout. E' esclusa qualsiasi responsabilit nei nostri confronti in caso d'errori di stampa e sbagli, sorti durante la produzione delle istruzioni di montaggio. Con riserva di ulteriori possibilit di fornitura e di modifiche tecniche. Stato 06.00 Instrucciones del instalacin 732.29.108 Queda rigurosamente prohibida la reproduccin total o parcial de esta documentacin, as como la imitacin de sus ilustraciones, dibujos o diseo. No nos hacemos responsables en manera alguna de las erratas o equivocaciones que pudieran existir en estas instrucciones de instalacin. Nos reservamos la posibilidad de suministro y los derechos a modificacin. Versin del 06.00 Copyright Hfele GmbH & Co Adolf-Hfele-Strasse 1 D-72202 Nagold Postfach 1237 D-72192 Nagold Telefon +49 (0) 74 52 / 95-0 Telefax +49 (0) 74 52 / 95-200 E-Mail: info@haefele.de www.haefele.de