FCC ID: 2AQ4R-HP-H006 Turntable Player

ey WIP pen an pb wN bp DC INPUT Jack Phono & Line Out Switch AUXIN Jack Phono & Aux Out Jacks lid Hinge Counterweight Tracking Force Dial Tonearm Lift Lever Tonearm Clip 10. 11. 12. 13. 14. 15. 16. 17. 18. Tonearm Volume Control Indicator Speed Selector Button Play/Stop Button ON/OFF /Function Button Stylus Cartridge Turntable platter Turntable spindle 1) 2) 3) 4) 5)

) Turntable Unit Power Adapter Turntable Lid Slip Mat Platter with Belt Counterweight Cartridge Alignment Protrac tor 45 RPM Adapter Instruction Manual Makesure that the drive beltis looped in the middle of the ircle. The drive belt located too high or too low in this cirde may cause the drive belt to fall off or speed to be unstable. Motor Pulley Opening _ % > Platter _ 6 aN ew ZS Spindle Straight Twisted ___Weonglaation 1. Using your hands, slowly rotate the platter ten times in a clockwise direction (Figure 1). 2. This stepis for resettingthe auto mechanism, getting rid of any twists in the belt and making surethe belt rides smoothly along the drive rim on the underside of the platter. 3. Place the slip mat ontop ofthe platter. Make sure the logo on the matis facing up(Figure 2). The supplied Counterweight is | Comtervight suitable for cartridges weighing Taking fore Dal between 3.0-6.0g. OPN oe 1. Gently push and turn the counterweight Aces into the rear of the tonearm (with the dial eS facing toward the front ofthe turntable). {

2. Pull the protector straight forward to remove it. NOTE: Applying a downward force may cause the stylus to comeoffthe body. Only low volumeis output if the stylus has come off, or is aboutto come off, so referto

"Replacing the stylus" to reattach the stylus correctly. Tonearm Counterweight Adjust so that tonearm is level and neutrally balanced Note: Each mark on the scale represents 0.1g.The recommended tracking force for the factory installed cartridge is 3.5g40.5g. Carefully rotate the tracking force dial. When "3.5" is centered over the black line on the top ofthe tonearmpleasestop. Connectable equipment being wed Postion of pre-amplifier selector Where to connect RCA audio cable:

switch Device with phono input PHONO Phono input jack and ground:

(earth) terminal of connectable equipment Device without phono input LUNE AUXor line input jack of connectable equipment NOTE: The RCA Jacksare not designed to be connected directly to the passive/unpowered speakers on LINE mode. If connected to the passive speakers, there will be no sound. RCA wired connection Active Speakers or Soo O Amplifier NOTE: inorder toachieve the best sound, it is advised to set the turntable volume to minimal level. Thentheturntable's audio will be played back through your own amplifier, speakers, etc. With PHONO Without PHONO Pony une mono] une To outlet

Connectable equipment

(Amplifier, etc.) To outlet 7] ve With PHONO Without PHONO PHONO AUX NOTE: Do not plug the AC power adapter into a power outlet before all turntable assembly is completed. Before turning on turntable power, recheck all connections to make sure they are correct and secure. Always turn off the turntable before connecting or disconnecting from power. NOTE: Appiving a downward force may cause the styusto come af the body Only low volumes ourputif the stylus hes come of, oris about t come of sorefer to"Replacingthe stylus" to reattach the stylus correct NOTE:

L Ifthe silent pause time between each track is longer than 20 minute, the platter will stop spinning automatically to avoid damaging the record. The indicator ight will turn off. To resume operation, pressthe ON/OFF button. Ifthe felt mat gets dirty, it can easily scratch the record, so remove the felt mat periodically andwipe offany dust. To prevent the record from scratches and warping, remove it after use. Do notuse a diskstabilizer. NOTE:

1. Make sure the tone arm is securely locked to avoid any damage. 2. When you are done, don't forget to turn off the power on the turntable and your extemal device.

* Ifdirt and grime are stuck tothe stylus tip, deanit witha commercially soldbrish,

+ Werecommend using astyius cleaner

(not include) i the stylus tipis considerably dirty lean the stylus tip by moving the brush from the rearto the front ofthe stlustip. a

& Engage in body first Problem Solution The platter does not spin.

* Is the AC adapter connected to the outlet?

- Connect the AC adapterto the outlet. What's the status of the indicator light?

- The indicator light isgreen. That means the turntable is in AUXIN mode. Please press the mode button twice to switch to Turntable mode.

- The indicator light is blue. That means the turntable isin Bluetooth mode. Please press the mode button once to switch to Tumtable mode.

- The red indicator light will indicate Turntable mode. Has the beltslipped from the platter?

- Correctly place the belt on the platter. Is the belt placed on the motor pulley?

- heck that the belt is placed on the motor pulley (brass-cdored) correctly. Has the beltbeen damaged?

- Replace it witha new belt. The platter spins, but there is no sound from the turntable?

Is the stylus dama@ed?

- Gheck the stylus and replace it, if necessary. t's suggested to replace the stylus after 400 hours of use. Is the stylus placed corectly on the body of the cartridge?

> Qheck the cartridge and adjust it, if necessary. The stylus skips Is the record wamed?

- Check the record. Is the record scratched?

- Check the record. Is the stylus pressure correct?

- Referto "Cartridge Tracking Force Adjustment to readjust the tracking force. The turntable is making a strange howling sound Is the product picking up excessive vibrations from the floor, surfaces of the walls, or nearby speakers?

- Decrease the vibrations or mount the product ona surfacethatis not subject to the effects of vibrations. Is the product mounted on an unstable surface?

- Qheck whether the surface on which the product is mounted is suitable. Thereis noise when the record is playing Is there dust on the cartridge's stylus tip?

- If dust is stuckto the stylus tip, clean itwith a commercially sold brush. The sound when the record is playing is eithertoo fast or too sbw. Are the speed settings for this product correct?

- Please select the comect speed for the type of record being played. Playback speed slows down or there is imeguar rotation. Is the belt stretched out?

- Replace with anew belt.

|s the belt installed correct?

- Referto "Turntable Platter and Belt Setup" to setup the belt. Power Supply ACLO0-240V, DC output 12V 1500mA Power Consumption 35W Turntable Speed 33 1/3, 45 RPM Output Power (RMS) 40W on Bluetooth mode Speakers Rating 2x15W + 2x10W Dimensions (LxWxH) 17.32"x 14.57"x 7.56" (440 x 370 x 152mm)

(lid closed), 15.75"x 16.73"x 18.19"

(400 x 425 x 462mm) (lid open) Weight 13,31b (6,05kg) Model Audio-Technica AT3600 Frequency Response 2087-20kH2 Channel Balance <2.508 Channel Separation >18d8 Output Voltage 25mV Recommended Load Resistance a7kO Amplifier Connection MM (Moving Magnet)- input Recommended Tracking Force 3.5405g Weight 0.1802 (5.1g) Information Rating parameters Input voltage 100-240V Input AC frequency 50-60H2 Output voltage Dc Lv Output current 1S00mA Output Power sw

MODEL:HP-HO006-MA Input Voltage: 12V.1500mA Consumption: 35w Bluetooth range: 2402-2480MHz Max. RF emission power: -1.96dBm a4 C E Made in China 1 @1 Om | D7N@Y-1 S| e100 )6) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION - VORSICHT - ATTENTION - OPGELET Shock hazard - Do not open the housing Stromschlaggefahr - Nicht das Gehause 6ffnen uN Risque de choc lectrique - Ne pas ouvrir le boitier Risico voor elektrische schok - Niet de behuizing openen

Agent Authorization Company:Haiping Industry Co., Ltd. Address:3F, Building C, NO.68, Hongshi Road Buxin, Fenggang Town Dongguan, Guangdong China Product Name:Turntable Player Model Number(s):HP-H006-MA, HP-H006-XX, HP-H006X-XX, LS-410XX, LS-

410XXXX(X can be replaced by letter from A to Z, number from 0 to 9 or blank.) Product Description:Frequency in 2402-2480MHz, BT mode operation We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature:

Date: 2022-06-10 Name:

XingQuan Wu Title:

Manager Company: Haiping Industry Co., Ltd.

Haiping Industry Co., Ltd. Add: 3F, Building C, NO.68, Hongshi Road Buxin, Fenggang Town Dongguan, Guangdong China Date: 2022.06.10 FCC ID: 2AQ4R-HP-H006 Dear Sir/Madam, We, Haiping Industry Co., Ltd. Hereby declares the following statement for Federal Communications Commission, Except the model number, color and brand are different, everything else is the same.:

Product name: Turntable Player Model no.: HP-H006-MA, HP-H006-XX, HP-H006X-XX, LS-410XX, LS-410XXXX(X can be replaced by letter from A to Z, number from 0 to 9 or blank.) Sincerely, Name/Title Company:

Address:

Phone:

Fax:

E-Mail:

XingQuan Wu/Manager Haiping Industry Co., Ltd. Dongguan, Guangdong China 86-0769-82757922 86-0769-82757719 WXQ0906@163.com 3F, Building C, NO.68, Hongshi Road Buxin, Fenggang Town

Haiping Industry Co., Ltd. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Subject; Request for Confidentiality FCC ID: 2AQ4R-HP-H006 Date: 2022-06-10 To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure External Photos Test Setup Photos Internal Photos User Manual In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name:XingQuan Wu Title:Manager