FCC ID: 2AO7P-20180112-P 30IN 120W APP Control RGB LED Light Bar

1 2 0 m m 1 2 0 m m 1305257 Lamp Body 1305257 Bolt 30IN 120W APP Control RGB LED Light Bar Female Connector 1 Bracket PARTS LIST Description M8 x 15 mm bolt M8 lock washer M8 flat washer M8 x 40 mm bolt M8 nut 20A fuse Hex key NO. 1 2 3 4 5 6 7 Qty 2 4 4 2 2 2 1 1. Use fuse (6) with Wiring Harness

(SKU 1169555). For detailed instructions, please refer to SKU 1169555's user manual. 2. Wiring Harness (SKU 1169555) is not included in this product. Purchase separately, if needed. 4 2 3 5 6 7 1 of 13 120mm User Manual 120mm 1305257 1305257 1305257 1305257 1305257 INTENDED USE This 120W LED light bar is designed to supply additional light for Trucks, SUVs, ATVs, UTVs, farm equipment and heavy machinery while drawing very low additional amps. This rugged light features an IP67 weatherproof design with bright CREE LED bulbs. It is constructed from a durable aluminum housing and has an adjustable mounting bracket. TECHNICAL SPECIFICATIONS Item Description Bulb Type CREE LED Voltage DC 12V-36V Beam Pattern SPOT Product Size 32.99" L x 1.90" W x 2.75" H Beam Distance 984 ft (300 m) Lumen 7,850 Mount Type Bolt LIGHT USE AND CARE 1. Do not shine directly into your eyes. 2. Slowly tighten endcap bolts, do not over-tighten, stop when lock washers are flattened. 3. Do not turn on light during assembly, it may damage the light. 4. This is an off-road auxiliary light, not DOT approved. INSTALLING THE LIGHT Step 1: Use the provided M8 x 15 mm bolts , and M8 lock washer , M8 flat washer to assemble the light and the bracket . Step 2: Adjust light to sit at the preferred angle and tighten the mounting plate bolts . Notice: The bolts are specially designed with M8 thread and M6 hex head. Notice: Do not over tighten any bolts. 2 of 13 120mm 3 of 13 120mm Step 3: Use provided M8 x 40 mm bolts , M8 lock washer , M8 flat washer , and M8 nut to mount the light onto the equipment. Notice: 1) The hole on the mounting surface should be 3/8 inch diameter. 2) Supplied bolts are 1.5" (40 mm) length. Notice: Do not over tighten any bolts. Step 4: Connect wiring terminal with battery. Red cable to positive of power source. Black cable to negative of power source. Mount the switch to the dashboard. When the switch press to -, The RGB LED ON. When the switch press to O, The light OFF. When the switch press to =, The white LED ON. Notice: Do not over tighten any bolts. 4 2 3 0.35inch hole on Vehicle mounting surface 8 Switch 2.5ft Fuse Vehicle mounting surface 5 5 of 13 120mm 4ft 6 of 13 120mm Red cable

+

360 rotation

-

Black cable 9 3 1 360 rotation 2 10 4 of 13 120mm USE APP TO CONTROL THE RGB LED Step 1: Scan below QR code to download the APP Step 4: Follow below step to read instruction on APP before use. Step 4: Follow below step to read instruction on APP before use. 1305257 1305257 LED BLE Step 2: Push the switch to - and open the Bluetooth of your phone. Do not connect the Bluetooth controller in the phone settings. Step 3: Open the LED BLE. APP will automatically connect to the Bluetooth controller and the APP will display 1 device for normal control. 7 of 13 120mm 8 of 13 120mm Hand automatic switching All Devices Device List Number of Devices Color ring is changed Refresh Connection succeeded Settings Switch Dimming Color customization 9 of 13 120mm 1305257 Connection succeeded Settings Switch Selection of color Dimming Color customization Output frequency Playback process Playback order Color editing Click Change Output Mode Song Library Previous Play/Pause Next 10 of 13 120mm 1305257 1305257 1305257 1305257 USE APP TO CONTROL THE RGB LED FEATURES 1. For IOS system, please add the music through Apple software Itunes. 2. The connection last 24 hours, please re-set the light after 24 hours. For example, when set up the light at 11:00 am, please re-set the light at 11:00 am one day later. CONNECTION 1. Check whether the device is powered or the phone Bluetooth is turn on if the RGB wont work. 2. Please do not connect the Bluetooth controller to your Bluetooth settings. 3. Click refresh to see if the connection can be successful. 11 of 13 120mm FCC Statement FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. 12 of 13 120mm This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Distributed by:

DUOLI HOLDINGS CO., LIMITED RM901, SIDE A, UNIT 1, LIANHE MANSION HANG ZHOU, ZHE JIANG, 310012 For customer support, www. evergearautomotive.com 13 of 13 120mm

FCCIDLABEL:

LabelLocation FCC ID: 2AO7P-20180112-P Model No.: 20180112-P Product name: 30IN 120W APP Control RGB LED Light Bar Width:2cm This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and

(2)This device must accept any interference received, including interference that may cause undesired operation. Long:4cm

< Hang Zhou DingYu Electronic Technology Co.,Ltd >

Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD21046 Date: Jun. 22, 2018 Subject; Request for Long Term Confidentiality FCC ID: 2AO7P-20180112-P To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: Jianghui Zhu Title: Manager

Hang Zhou DingYu Electronic Technology Co.,Ltd Letter of Authorization Rm901, Unit One, Union Plaza A, No.2, zi Jin hua Road, Hangzhou, China Company: Hang Zhou DingYu Electronic Technology Co.,Ltd Address:

Product Name: 30IN 120W APP Control RGB LED Light Bar Model Number: 20180112-P FCC Identifier: 2AO7P-20180112-P We authorize MiCOM LabsInc, 575 Boulder Court, Pleasanton, California94566, USA, to act on our behalf on all matters concerning the above named equipment. Any individual within MiCOM Labs is authorized to act on our behalf and take action on the application. We declare that MiCOM LabsInc, 575 Boulder Court, Pleasanton, California 94566, USA, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Name: Jianghui Zhu Title: Manager Signature of applicant:

Date: Jun. 22, 2018