Box Content Internet Camera (x1) USB Cable (x1) Power Adapter (x1) Foam Sticker (x2) Metal Plate (x1)
(3.5mm Hole Diameter) Regulatory Information
(x1) Quick Start Guide (x1) The camera appearance is subject to the actual one you have bought. Basics Lens MIC LED Indicator Magnetic Base microSD Card Slot RESET Button Speaker Power Input Name LED Indicator Description Solid Red: Camera is starting up. Slow-flashing Red: Wi-Fi connection has failed. Fast-flashing Red: Device exception (e.g. microSD card error). Solid Blue: Video is being viewed or played back in EZVIZ App. Fast-flashing Blue: Camera is ready for the Wi-Fi connection. Slow-flashing Blue: Camera is running properly. microSD Card microSD Card should be purchased separately. Initialize the card in the EZVIZ app before using it. RESET Button Hold down the RESET button for 5 seconds while the camera is running, the camera restarts and all parameters are reset to default. Setup Step 1 Power-on Plug the power cable into the camera and to the power adapter and then into a power outlet, as shown in the figure below. Power Outlet Power Cable Step 2 Camera Setup 1. Create a user account
- Connect your mobile phone to Wi-Fi.
- Download and install the EZVIZ app by searching EZVIZ in App Store or Google PlayTM.
- Launch the app and register for an EZVIZ user account following the start-up wizard. 1 2. Add a camera to EZVIZ
- Log in the EZVIZ app.
- From the EZVIZ app Home screen, tap + on the upper-right hand corner to go to the scan QR code interface.
- Scan the QR Code on the bottom of the camera. Bottom of the Camera
- Follow the EZVIZ app wizard to finish Wi-Fi configuration. Please make sure your phone is connected to the 2.4GHz Wi-Fi from the router for Wi-Fi configuration. Installation Step 1 Install the Metal Plate (Optional) Pick a clean and flat surface and secure the metal plate to the desired position with the foam stickers or screws (not included). Theres a magnet piece inside the camera. You can skip this step if the surface is made of metal. Step 2 Install the Camera Secure the camera magnetically to the metal plate or metal surface (see figure below). Foam Sticker Metal Plate Step 3 Complete Installation Adjust the camera angle as required. Appendix Step 1 Install Memory Card Insert a microSD card into the slot until a click. Step 2 Initializing Memory Card 1. In the EZVIZ app, check the memory card status by tapping on the Storage Status in the Device Settings interface. 2. If the memory card status displays as Uninitialized, tap to initialize it. The status will then change to Normal. For detailed information, please visit www.ezvizlife.com. 2 Regulatory Information This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the Radio Equipment Directive 2014/53/EU, the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU. 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info 2006/66/EC and its amendment 2013/56/EU (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info EC DECLARATION OF CONFORMITY Hereby, Hangzhou EZVIZ Software Co., Ltd. declares that the radio equipment type [CS-C1C, CS-C1HC, CS-C1T, CS-C2C, CS-CV206, CS-CV310, CS-C3N, CS-C3W, CS-C3WN, CS-C3X, CS-C6N, CS-CV246, CS-CV248, CS-C6CN, CS-C6C, CS-C6W, CS-TY1, CS-TY2, CS-TY3, CS-CV336, CS-DP1, CS-DP1C, CS-DP2C, CS-DB2C, CS-C4W, CS-C4C, CS-CV228, CS-C5W, CS-C5C, CS-C5HC, CS-C5X, CS-C5HX, CS-C8W, CS-C8C, CS-CP1, CS-C3A, CS-BC1, CS-BC1-B1, CS-BC1-B2, CS-BC1-B3, CS-BC1-B4, CS-BC1C, CS-W2H, CS-X5S-4W, CS-X5S-8W, CS-A1-32W, CS-T9-A, CS-T4-A] is in compliance with Directive 2014/53/EU. The full text of the EC DECLARATION OF CONFORMITY is available at the following web link:
http://www.ezvizlife.com/declaration-of-conformity. Use only power supplies listed in the Table. Equipment model Adapter manufacture Shenzhen Honor Electronic Co Ltd CS-C1C/ CS-C1HC/ CS-C1T/
CS-C2C/ CS-CV206/
CS-CV246/CS-C6N/ CS-C6CN/
CS-C6C/ CS-TY1/ CS-TY2/
CS-TY3/ CS-W2D/ CS-A1-32W/
CS-T9-A/ CS-BC1C/ CS-CP1 Sichuan Jiuzhou Electronic Technology Co., Ltd DYS05100CP-U, DYS05100CP-E CS-CV248/ CS-C6W/ CS-C6Wi/
CS-CV336/ CS-DP1/ CS-DP1C/
CS-DP2C/ CS-C3A/ CS-BC1/
CS-CP1 Shenzhen Honor Electronic Co Ltd Sichuan Jiuzhou Electronic Technology Co., Ltd DYS05200CQ-U, DYS05200CQ-E Shenzhen Honor Electronic Co Ltd CS-CV310/ CS-C3N/ CS-C3W/
CS-C3WN/ CS-C3X/ CS-SD1/
CS-C4W/ CS-C4C/ CS-CV228/
CS-C8W/ CS-C8C/ CS-W2H/
CS-W3C-WD1200G/ CS-T8-B CS-X5S-4W/ CS-X5S-8W/
CS-X5S-16H Moso Power Supply Technology Co. Ltd Adapter model ADS-5RE-06 05050EPCU/EPC(US), ADS-5RH-06 05050EPB(UK), ADS-5RH-06 05050EPG(EU), ADS-5RH-06 05050EPSA(AU), ADS-5RH-06 05050EPBR(BR), ADS-5RH-06 05050EPI(IN), ADS-5MA-06A 05050GPK(KR) ADS-10LA-06 05010EPCU/EPC(US), ADS-10RH-06 05010EPB (UK), ADS-10RH-06 05010EPG(EU), ADS-10RH-06 05010EPSA(SA), ADS-10RH-06 05010EPBR(BR), ADS-10RH-06 05010EPI(IN), ADS-12CG-06 05010EPC(JP) ADS-12FG-12N 12012EPCU(US), ADS-12FG-12N 12012EPB(UK), ADS-12FG-12N 12012EPG(EU), ADS-12FB-12 12012EPSA(AU), ADS-12FG-12N 12012EPBR(BR), ADS-12FG-12N 12012EPI(IN) MSA-C1500IC12.0-18P-GB(UK), MSA-C1500IC12.0-18P-DE, MSA-C1500IC12.0-18P-AU(AU), MSA-C1500IC12.0-18P-BR(BR), ADS-25FSG-12 12018GPI(IN) Important Safety Information Note: Please read the manual before using the device. This symbol on the device indicates that the safety compatibility manual and / or installation manual must be read, which contains information related to the safe operation of the device. Caution: Be sure to read these instructions before operating the equipment. This symbol on the device indicates that the surface or component is overheating. If you touch this surface, you may cause personal injury. Warning: To reduce the risk of personal injury due to overheating of the components, wait until the surface cools down before touching it. Warning: The separate earthing terminal must be permanently connected to earth. Warning: For SELV DC input: the DC power source shall comply with the Safety Extra-Low Voltage (SELV) requirements of IEC 60950-1. Caution: Do not block ventilation openings while the system is on, and keep at least 2 cm distance from ventilation openings and walls or other things which may block the openings. Warning: Disposal of a battery into re or a hot oven, or mechanically crushing or cutting of a battery that can result in an explosion. Warning: Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas. Warning: A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas. Warning: Dispose of used batteries according to the instructions. Warning: Replace only with the same or equivalent type recommended by the manufacturer. Caution: THE PRODUCT IS BUILT IN A REPLACEABLE BATTERY. Warning: Do not ingest battery, Chemical Burn Hazard. Caution: This product contains a coin/button cell battery. If the coin / button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Caution: Keep new and used batteries away from children. Caution: If the battery compartment does not close securely, stop using the product and keep it away from children. Caution: If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. Caution: Risk of re or explosion if the battery is replaced by an incorrect type. FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body. FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence. L'exploitation est autorise aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. Cet quipement doit tre install et utilis une distance minimale de 20 cm entre le radiateur et votre corps. IFETEL Information La operacin de este equipo est sujeta a las siguientes dos condiciones:
(1) es posible que este equipo o dispositivo no cause interferencia perjudicialy
(2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacin no deseada. 102026549D