T02C5N0O Wireless Bridge User Manual

 

See Far,Go Further DS-3WF02C-5N/O Quick Start Guide DS-3WF02C-5N/O Quick Start Guide DS-3WF02C-5N/O Quick Start Guide Quick Start Guide COPYRIGHT 2019 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be Hikvision). This user manual (hereinafter referred to be the Manual) cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties, guarantees or representations, express or implied, regarding to the Manual. About this Manual This Manual is applicable to DS-3WF02C-5N/O (Product Series). The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version in the company website (http://overseas.hikvi-

sion.com/en/). Please use this user manual under the guidance of professionals. Trademarks Acknowledgement and other Hikvisions trademarks and logos are the properties of Hikvision in various jurisdictions. Other trademarks and logos mentioned below are the properties of their respective owners. Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED AS IS, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICU-

LAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEV-

ER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. 3.This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, the LVD Directive 2014/35/EU, the RoHS Directive 2011/65/EU. 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recycle-

this.info 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements. DS-3WF02C-5N/O Quick Start Guide DS-3WF02C-5N/O Quick Start Guide Catalog Chapter 1 Introduction ............................................................................................................. 1 1.1 Overview ............................................................................................................................ 1 1.2 Packing List ......................................................................................................................... 1 1.3 Appearance ........................................................................................................................ 1 1.3.1 Front Panel ...................................................................................................................... 1 Chapter 2 Installation ............................................................................................................... 3 Chapter 3 Prepare .................................................................................................................... 5

......... 7 Chapter 4 Conguration ......................................................................................................... Applicable Models This manual is applicable to switches below: DS-3WF02C-5N/O (product series). Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description NOTE Provides additional important points of the main text. information to emphasize or supplement WARNING Indicates a potentially hazardous situation, which if not avoided, could result loss, performance degradation, or unexpected results. in equipment damage, data DANGER Indicates a hazard with a high level of risk, which if not avoided, will result in death or serious injury. WARNING During the installation and utilization of the device, please strictly conform to electrical safety rules in different nations and regions. You shall acknowledge that the use of the device with Internet access might be under network security risks, please strengthen protection for your personal information and data security. If you find the device might be under network security risks, please contact with us. DS-3WF02C-5N/O Quick Start Guide Chapter 1 Introduction 1.1 Overview DS-3WF02C-5N/O wireless bridge can be applied in industries, such as wireless video surveillance, railway, transportation, power and other industries, wireless video/data transmis-

sion, wireless coverage, carrier wireless backbone network construction, Wi-Fi wireless coverage, rural information construction, and wireless network coverage. The long-distance transmission of the device can guarantee multi-channel HD video transmission. 1.2 Packing List The packing list is shown as below. If any accessories are damaged or lost, keep the package intact and contact your dealer for replacement. Name Device PoE Adapter Power Cord Hoop Quick Start Guide Item DS-3WF02C-5N/O 24 V, 0.5 A Power Cord Hoop for mounting device Instruction manual Quantity 1 1 1 1 1 Table 1-1 Packing List of DS-3WF02C-5N/O 1.3 Appearance 1.3.1 Front Panel Front panel of DS-3WF02C-5N/O is shown as below. Front Panel of DS-3WF02C-5N/O DS-3WF02C-5N/O Quick Start Guide Indicator Indicators are used to monitor the status of the DS-3WF02C-5N/O. See the following table for the description of the indicators. Figure 1-2 Indicators Indicator LAN WLAN Description Power indicator. If the green light is steady on, it indicates that the power is on. Network connection light. The light indicates there is one IPC or other network device connects to the LAN port of PoE adapter. Blinking means sending data. Wireless indicator light. The light indicates that the wireless is enabled. Blinking means sending data. Signal strength indicator light. Red light on, indicating that the signal is weak or no signal. Yellow and red lights on, indicating signal level is medium. Green, yellow and red lights on, indicating the wireless signal level is strong Table 1-2 Indicator Description Physical Interface The hardware interfaces of the DS-3WF02C-5N/O are as follows. 1 Figure 1-1 DS-3WF02C-5N/O Front Panel Figure 1-3 Physical Interface Physical Interface Description LAN Reset The reserved network port can be connected to front-end network devices such as IPC. Used to restore the default factory settings. POE The network cable is connected to the POE on the PoE power module to provide power and data transmission to the device. Table 1-3 Physical Interface 2 DS-3WF02C-5N/O Quick Start Guide Chapter 2 Installation DS-3WF02C-5N/O Quick Start Guide Step 3 The schematic diagram of the installation of the device is as follows. Step 1 Select the unobstructed high point around the device to ensure that the devices are aligned and there is no obstruction in the middle. Fix the device as shown in the figure below. Attach the back of the device to the pole, use the hoop to pass through the hoop hole on the back of the device, tighten the hoop, and fix the device on the pole. LAN PoE PoE LAN PoE Adapter Figure 2-1 Install host Figure 2-3 Finish installation Step 2 Connect the PoE interface of the device to the PoE interface of the PoE power supply through the network cable. The LAN interface of the device and the LAN interface of the PoE power supply can be connected to the front-end network devices such as IPC through the network cable, as shown in the following figure. PoE Adapter POE LAN Protective cover The PoE port of the device is connected to the PoE port of the PoE adapter through a network cable. Figure 2-2 Power on the device 3 4 DS-3WF02C-5N/O Quick Start Guide Chapter 3 Prepare Step 1 Use a network cable to connect the computer to the LAN interface of the device or PoE power supply to prepare the device. First, you need to configure the computer IP address and the device's default IP address to be on the same network segment. Take the Windows 7 system as an example. Click the network logo in the lower right corner of the desktop and click Open Network & Internet settings-Network and Sharing Center. As shown below. Network Internet settings Change settings,such as makeing a connection metered. MK-WIFI Airplane mode Mobile hotspot 9:43 PM 1/1/2019 Figure 3-1 Network & Internet settings ENG Step 2 Click Local Area Connection on the right and click Properties. As shown below. Ethernet 2 Status General Connection IPv4 Connectivity:

IPv6 Connectivity:

Media State:

Duration:

Speed:

Details... Activity Sent Bytes:

57,467 Properties Disable Diagnose Internet Internet Enabled 00:00:35 1.0Gbps Received 117,331 Close Figure 3-2 Local Area Connection Step 3 Double-click Internet Protocol Version 4 (TCP/IPv4). As shown below. 5 DS-3WF02C-5N/O Quick Start Guide Ethernet 2 Properties Networking Sharing Connect using:

ASIX AX88179 USB 3.0 to Gigabit Ethernet Adapter This connection uses the following items:

Configure... Client for Microsoft Networks File and Printer Sharing for Microsoft Networks QoS Packet Scheduler Internet Protocol Version 4TCP/IPv6 Microsoft Network Adapter Multiplexor Protocol Microsoft LLDP Protocol Driver Internet Protocol Version 6TCP/IPv6 Install... Uninatall Properties Descripton Transmission Control Protocol/Internet Protocol. The default wide area network protocol that provides communication across diverse interconnected networks. Figure 3-3 Internet Protocol Version 4 (TCP/IPv4) OK Cancel Step 4 Configure the IP address of the computer to be the unused 192.168.1.X address in the LAN. X is any integer other than 36 in 2 to 253. The subnet mask is 255.255.255.0. Click "OK"

as shown below. General You can get IP settings assigned automatically if your network supports this capablity. Otherwise,you need to ask your network adminstrator for the appropriate IP settings. Obtain an IP address automatically Use the following IP address:

IP address:

Subnet mask:

Default gateway:

192 .168 . 1 . 2 255 . 255 . 255 . 0 Obtian DNS server address automatically Use the following DNS server addresses Preferred DNS server Alternate DNS server Validate settings upon exit Advanced... Figure 3-4 Configure the IP 6 DS-3WF02C-5N/O Quick Start Guide Chapter 4 Configuration After the preparation is completed, start the device configuration. Step 1 Make sure that the IP address of the computer is inconsistent with the default IP address of the device. On the same network segment, use a browser to log in to the device, open a browser, and enter the default IP address of the device in the address bar: 192.168.1.36. NOTE When you log in to the device for the first time, click Enter, enter the device activate page. The user name is admin, and the user password is set by the user. You also need to select your password, country, language and time zone, as shown in Figure 4-1. Check "I agree to these terms of use" and click "Activate. Take the AP device as an example. Username admin New Password Please set a password Confirm Password Please confirm the password Country/Region Please select country code Time Zone Please select time zone Language English TERMS OF USE Installer must install this device professionally. It is the installer's responsibility to follow local country regulations including operation within legal frequency channels,output power requirements. I agree to these terms of use Figure 4-1 login Step 2 Go to the device page and click the Wizard bar at the top of the page to enter the Network page to set the IP address of the device. In the address field of the LAN IP, fill in 192.168.1.X, X is any integer from 2 to 253, and the address is not used. The subnet mask can be used by default. Click Next when finished. 7 DS-3WF02C-5N/O Quick Start Guide This wizard page is only used in bridge mode helps to set the basic network parameters. Network LAN IP:

192.168.1.36 LAN Netmask:

255.255.255.0 Gateway IP:

192.168.1.100 Figure 4-2 Wizard Network Step 3 Go to the Wireless page. The device can modify the wireless parameters such as network name, frequency, and key through this page. The default wireless mode of the device is the WDS Station. The default network name of the device is Wireless_R. When pairing with the WDS Access Point device, please note that the key and the SSID on the WDS Station side must be the same as the WDS Access Point. Other configurations are recommended to keep the default values. Click "Next". This wizard page helps to set the basic wireless and wireless security,Please click the topWirelessmenu for detail setting. Wireless Wireless Mode:

WDS Station SSID:

Wireless_R Output Power:

Allowing adjusting transmission power Caution:It is installer`s responsibility to follow local regulations while adjusting the transmission power IEEE802.11 Mode:

A/N mixed Channel Width:

20 MHz Wireless Security[?]:

WPA WPA2-PSK Key:

Figure 4-3 Wizard Wireless Step 4 Go to the Setup Wizard Finish page and click Change to save the configuration. 8 DS-3WF02C-5N/O Quick Start Guide Wizard-Finish You have finished the wizard. please click Changeto save all your settings,and clickApplyto reboot and make your settings work. Figure 4-4 Wizard Finish Users can also click the Wireless bar at the top of the page to enter the Wireless page and modify the network name, frequency, key and other parameters. Wireless Mode[?]:

WDS Station SSID:

Wireless_R Antenna Gain:

Output Power:

Allowing adjusting transmission power Caution:It is installer`s responsibility to follow local regulations while adjusting the transmission power Basic Wireless Settings IEEE 802.11 Mode:

A/N mixed Country Code:

Argentina Channel Width[?]:

20 MHz Max TX Rate,Mbps[?]:

MCS 15-130(144) Lock AP Mac:

Wireless Security Settings Security:

WPA Mode:

WPA2 Cypher:

CCMP WPA Key:

Show Figure 4-5 Wireless For the WDS Access Point device configuration, please refer to the WDS Station device configuration. 9