FCC ID: 2BBHZJHAP Portable EV Charger

MODEL:JHAP-24032A/12016A PORTABLE EV CHARGER USER MANUAL JHAP-24032A/12016A CONTENTS Topic Page Important Safety Instructions Important Safety Instructions Portable EV Charger Components Power Outlet Adapter Specification Charging Rate Reference Information of Display Screen and LED Ring Indicator Operation Fault Technical Parameter FCC Rules 2 2 3 3 4 4 4 5 6 8 9 This instruction manual shall not be reproduced without authorization 1 1 .Important Safety Instructions Save These Instructions Read this entire document before using the Charger. Failure to do so or to follow any of the instructions or warnings in this document can result in fire, electrical shock, serious injury or death. Cautions:

1.Risk of electrical shock or burn. 2.The device does not contain any user-serviceable parts. 3.Please do not leave until the charging box is in charging status. 4.Do not use private power generators as a power source for charging. 5.Do not operate the Charger in temperatures outside its operating range of -

22F to +122F (-30C to +50C). Warnings:

1.Do not use this product if it is damaged. 2.Only use for EV charging. Ventilation not required. 3.Connect only to properly grounded outlets. 4.Do not use this device with an extension cord or an adapter. 5.Automatic CCID reset provided. 6.Do not disconnect the Charger from the wall outlet when the vehicle is charging. 7.Do not plug the Charger into a damaged, loose or worn power outlet. Ensure that the prongs on the Charger t snugly into the wall outlet. 8.Do not expose the Charger to ammable or harsh chemicals or vapors. Do not use or store the Charger in a recessed area or below oor level. When using the Charger in an inside location such as a garage, position the Chargers main controller at least 18 inches (46 cm) above the oor. 9.Do not use the Charger when either you, the vehicle or the Charger is exposed to severe rain, snow, electrical storm or other inclement weather. 10.When transporting the Charger, handle with care to prevent damage to any of its components. Do not subject the Charger to strong force or impact. Do not pull, twist, tangle, drag or step on the Charger or any of its components. 11.Protect the Charger from moisture, water and foreign objects at all times. If any exist or appear to have corroded or damaged the Charger, do not use the Charger. 13.If rain falls during charging, do not allow rain water to run along the length of charge cable, causing the electrical outlet or charging port to become wet. 14.Do not plug the Charger into an electrical outlet that is submerged in water or covered in snow. If, in this situation, the Charger is already plugged in and needs to be unplugged, turn off the breaker before unplugging the Charger. 2 15.Ensure that the Chargers charging cable does not obstruct pedestrians or other vehicles or objects. 2.Portable EV Charger Components 3. Power Outlet Adapter 3 4. Specification Use only a 120-volt or 240-volt AC supply, 50/60 hertz wall outlet that has a dedicated and properly grounded circuit, and is rated for at least 12A. If possible, use a dedicated receptacle with a single socket. If the receptacle has two sockets, do not plug any other items into the other socket. The Mobile Connector is 23 feet (7 meters) long. Use an existing outlet or install a new outlet within approximately 13 feet (4 meters) of the vehicle's charge port and at least 18 inches (45 cm) above the ground. Do not use an extension cord, a multi-outlet adapter, a multi-plug, a conversion plug, or a power strip as the power source. 5.Charging Rate Reference Outlet 5-20*

5-15 Outlet 6-20*

14-50 Rate 16A 12A Rate 16A 32A Power at 120V 1.9kW 1.4kW Power at 240V 3.8kW 7.7kW

*The Adapter for Outlet 5-20/6-20 need to purchase 6. Information of Display Screen and LED Ring Indicator The Display Screen Information The LCD screen shows the relevant electrical parameters and charging time of the charging operation, and the work / failure bar indicates the working process and fault category. The working screen will go to the screensaver screen while charging, and you can switch to the working screen by clicking the button . 4 The LED Ring Indicator Information LED Ring Indicator State Black Yellow Light 1s Flash Blue Light On Yellow Light On Blue Flashes Green Light On Yellow Flashes Red The charger is not connected to the power supply Power system initialization The vehicle is not connected Vehicle already connected, waiting to be charged Is charging Charging is completed Charging at high-temperature Fault 7.Operation Use only on mains power with fault current circuit breaker. Carefully read this guide together with your vehicle owners handbook prior to charging your electric vehicle. 7.1. Power On Firmly insert the power plug into the outlet on the wall. When the device is powered on, the system enters a self-test, and the status indicator will display yellow. The device is ready when the Status indicator turns blue, and the LCD will display charging information. The maximum current is automatically selected according to the socket voltage or at every Power on. As well, According to the Power Plug used (14-50P/6-20P/5-15P/5-20P) to select current: Press and hold the current Set button for 5s to select the maximum charging current (By selecting items:

14-50P 32A 240V 6-20P 16A 240V 5-20P 16A 120V 5-15P 12A 120V Press and hold button for 5s to select item) before inserting the charger plug

(car side). 7.2 Start Charging Connect the vehicle and the charging connector to begin the charging process. The screen displays "charging", and the LED status indicator is flashing blue. 5 7.3 End Charging The vehicle ends charging automatically, and the LED status indicator remains green. The user unplugs the vehicle connection, and the LED status indicator remains blue. With the vehicle unlocked, disconnect the Type 1 charger plug from the vehicle inlet, and disconnect the power plug from the outlet. Cover the charger plug dust cap and store the charger unit in the bag provided. 8. Fault 8.1 Troubleshooting Fault Situation Method of Operation Status Indicator Light is Not On (white) 1. Power supply disconnected - Check circuit breaker and ensure breaker is set to ON. 2. Equipment failure. Contact Support 1.Charging plug is not correctly inserted into the vehicle

- Unplug and Reconnect Securely Charging Cannot Start

(yellow or green light) 2. The vehicle has been set to reserve charging -

check the vehicle Charging Time Extended Steady Red Light 3. The vehicle does not need to charge or vehicle fault- -Check the vehicle 1. Vehicle in reserve charging mode 2. Reduced charging due to high temperature. Check current values on LCD Display. 3. Charging current at max. Check current values on LCD display. If charging station faults, refer to the fault information displayed on the LCD screen. Disconnect charging plug, shut off the power supply (disconnect the circuit breaker). Wait 30 seconds and turn on power supply to restart system. If the issue persists, contact customer support. 6 8.2 Possible Causes of Fault LCD Display Fault Shown Status Overcurrent Overvoltage Under-voltage Contactor Err Overcurrent protection. Charge again after 10-min interval. If overcurrent fault occurs three times, end charging and contact customer support. Overvoltage protection. Resume charging after the voltage is normalized. Under-voltage protection. Resume charging after the voltage is normalized. Contactor status failure. Contact customer support. Over-temperature Over-temperature protection. Resume charging after temperature is cooled. CCID Leakage CCID leakage protection. Remove vehicle plug and reconnect after 30 seconds. Ground Fault Ground-fault protection. Check Outlet for proper grounding and L/N whether or not it is proper. Short Circuit Err Short circuit protection. Contact customer support. Control Pilot Err Control pilot failure. Abnormal draw during charging. 7 9. Technical Parameter Description Project Parameter Electrical Parameters Interface Ambient Condition Configuration Parameter Voltage Maximum current Power incoming plug Standby active power consumption Internal residual current detection Electrical protection 120VAC/240VAC, Single-phase, 60Hz 12A/16A/32A (available by button setting socket No.) 14-50P/5-15P 3W CCID20 Overvoltage, under-voltage, overcurrent, short circuit, grounding fault, overheat protection, surge protection display mode 2.4-inch color dot matrix screen

+ LED loop charging connector SAE J1772 type 1 communication Bluetooth(backup) working temperature Storage temperature humidity altitude

-22~+122 over140for capacity reduction

-40+176 95% (No condensation) 3km levels of protection Type 4;IK08 charging cable Power cable 23ft 1ft Dimensions (width *

height * depth) 208*98*57.5mm, excluding the charging cable and power cable weight 4.2kg with charging cable and Power cable 8 10. FCC Rules This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. http://www.sunhopepower.com

Hangzhou sunhope electric Technology Co.,LTD Certification Application Attestation Statements Date: June 9, 2023 American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 To Whom It May Concern:

Statement for 47 CFR section 2.911(d)(5)(i) Hangzhou sunhope electric Technology Co.,LTD. certifies that as of the date of the application the equipment for which authorization is sought is not covered equipment1 prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, including affiliates or subsidiaries of the named companies, the applicant must include an explanation on why the equipment is not covered equipment. Additional Explanation: <N/A>

Statement for 47 CFR section 2.911(d)(5)(ii) Hangzhou sunhope electric Technology Co.,LTD. (the applicant) certifies that, as of the date of the filing of this application, the applicant - is / - is not identified on the Covered List as an entity producing covered equipment. Thank you, By:

____ ________________ ___wuliyun___ ______

(Signature2)

(Print name) Title:

__Department manager______ Company:

_Hangzhou sunhope electric Technology Co.,LTD. Telephone: _86-571-88937755_ 1 - The Commissions Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commissions website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes covered equipment. https://www.fcc.gov/supplychain/coveredlist . 2 - Letters must be placed on appropriate letterhead. 022423-17 rev 6

Hangzhou sunhope electric Technology Co.,LTD Authority to Act as Agent Date: June 9, 2023 American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 To Whom It May Concern:

______Intertek Testing Service Shanghai______ is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. We also declare that the information provided to the FCC is true and correct to the best of our knowledge (47 CFR 2.911(d)) and we have been informed of the grantee responsibilities (47 CFR 2.909) with regard to certified equipment. Thank you, Agency Agreement Expiration Date: ___June 2,2024______ By:

_______ __________________ _____wuliyun______________

(Signature1)

(Print name) Title:

__Department manager_______ On behalf of: _Hangzhou sunhope electric Technology Co.,LTD.__

(Company Name) Telephone:

_86-571-88937755_ 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead. 050222-17

Hangzhou sunhope electric Technology Co.,LTD Request for Confidentiality Date: June 9, 2023 Subject: Confidentiality Request for: ______2BBHZJHAP______ Pursuant to FCC 47 CFR 0.457(d) and 0.459 and/or IC RSP-100, Section 12.4, the applicant requests that a part of the subject application(s) be held confidential. Type of Confidentiality Requested Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Exhibit Permanent Block Diagrams

--------------------------- External Photos Permanent *1 Internal Photos Permanent Operation Description/Theory of Operation Permanent Parts List & Placement/BOM Permanent Tune-Up Procedure Permanent Schematics

--------------------------- Test Setup Photos Permanent *1 Users Manual Hangzhou sunhope electric Technology Co.,LTD. has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality for FCC Applications:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of __ (specify number of days not to exceed 180)2___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public before the requested period has expired. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. Short Term Confidentiality for Industry Canada Applications:

Starting May 2022, ISED will recognize short term confidentiality on certain exhibits until the intended date of marketing. The applicant requests the exhibits selected above as short term confidential be withheld from public view until: (specify ISED expiration date / date of marketing) . Sincerely, By:

(Signature/Title3) ___________________ _________wuliyun _________

(Print name) 1 - The asterisked items (*) require further information to be provided to ACB before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 and the specific Document link for D01 found at:

https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=41731 and review section II, 3) regarding specific information that must accompany these requests. 2 - Please refer to https://acbcert.com/documents/misc-docs/Memo-Short-Term-Vs-Standard-Confidentiality.pdf for complete details. 3 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead. 050222-17

Massimo MotorSports, LLC U.S. Agent Designation for Service of Process

(Applicant and U.S. Agent are Separate Parties) TO: American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 ATTENTION: FCC Certification Section 2.911(d)(7) Information Designated U.S. Agent Company Name: Massimo MotorSports, LLC Contact Name: David Shan Street Address: 3101 W Miller Rd Garland, TX 75041 City/Province/Zip: Garland Telephone No: 877-881-6376 Email: accounting@massimomotor.com FRN #: 0033850892 This letter is to confirm that we (the Designated U.S. Agent) have accepted the responsibility to act as the Designated U.S. Agent for Service of Process as required by section 47 CFR 2.911(d)(7) on behalf of the Applicant noted below. U.S. Agent Signature:

Date: June 9, 2023 Signed by (Printed Name/Title): David Shan The Applicant acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission-

related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information above changes. Applicant Company name:Hangzhou sunhope electric Technology Co.,LTD. Grantee Code: 2BBHZ Contact Name:wuliyun Street Address:Building 4,No.1099, Cangxing Road, Cangqian Street,Yuhang District, City/Province/Zip:Hangzhou ,Zhejiang, China Telephone No:86-571-88937755 Email:wuly@sunhopemeter.com Applicant Signature1:

Date: June 9, 2023 Signed by (Printed Name/Title):wuliyun

Hangzhou sunhope electric Technology Co.,LTD Model Difference Declaration We, Hangzhou sunhope electric Technology Co.,LTD declare:

Portable EV Charger: JHAP-24032A, JHAP-12016A The products above are electrical identical except the rated power. wuliyun Hangzhou sunhope electric Technology Co.,LTD. Date: June 13, 2023