Packing list Appearance introduction Indicator Introduction 2.Download APP After opening it, please check whether the product is in good condition or not; confirm whether the accessories are complete as below. SMART VIDEO DOORBELL User Manual Infrared fill Light PIR Sensor Photosensitive sensor MIC Bell button Before use, please be familiar with the interface and button of the doorbell. Machine RESET button AC24V Charging port Fittings:
Screws Package *2 Wooden Screw *4 Notes: Long-press the RESET button for 5 seconds, loosen it when hear the voice prompt "restore factory settings, please don't power off". Then it can be restored to the factory default configuration. Blue light always on Blue light flashes slowly Red light flashes slowly Startup APP remote monitor and setup Battery lower power Operation manual Tips one: Scan QR code to download;
iCSee Tips two: Search and download iCSee in the Appstore or Googleplay;
1.Device ready 3.Device network configuration First step: Install the backplane where you need to install the doorbell. (Expansion screws need to be used on cement and stone walls, wood screws or 3M glue can be used on wooden walls.) Second step: Install the doorbell body into the backplane. Camera Indicator Speaker USB Charging port Front Back 02.Device preparation After the doorbell is installed, short-press the bell button to wake the doorbell.(Figure 2) 03.Add device After login successfully, click "Add My Camera"
(Figure 3), input WiFi password (Figure 4). Finish the network configuration of the camera according to the APP operation hint. 4 5 Add device in the same WLAN: When the device and your smart phone have been connected to the same router, you can use this way to add the camera. AP hotspot stand-alone mode: The device can also can view real-
time video, which does not need to connect to the external network. Notes: This device does not support the AP mode and the AP hotspot stand-alone mode. The device is being awakened Awaking Online In this state, The mobile phone can make various accesses to the device;
1 2 3 4 5 Notes: If the configuration fails, reset the device. 05.Message push Click to check if the WiFi password is right 04.Access device After login success, you can use the mobile phone access the device through the APP, The device has the following states:
Device or network failure;
W h e n a v i s i t o r p r e s s e s a b u t t o n o r a n a l a r m i s generated, the device sends a message to the phone. You can receive the message in the following two ways:
1.Receive the message via the APP User login Open iCSee, sign up a new account and log in(Figure1;
Click "sign up" and input the corresponding information. Click the"WeChat"icon to set "WeChat shortcut login". If you have Wechat ,You can use WeChat shortcut login"
directly (Figure1;
(Figure 1)
(Figure 2) Notes: There is voice instruction throughout the process of device configuration. After hearing the voice prompt "wait to be configured", you can start configuring the device.
(Figure 3)
(Figure 4) Offline 1 Add My Camera (recommended): Connect the device to the 2 3 router. Add My Camera (AP mode): Connect the device to the router via AP mode. Add Shared Camera: Add a device that others share to you.Add the camera via inputting the device serial number or sharing information code or scanning device QR code. The device does not support remote wake-up
(or be set to prohibit remote wake-up),you can p r e s s t h e b u t t o n f o r m a n u a l a w a k e n i n g and access the device. The device is in low-power mode state, it needs to be awakened then access. Deep dormancy Dormancy Set up in the device use APP notification message. Confirm the current account. 2.Receive the message via WeChat. Log in APP with WeChat Set up in the device use Wechat notification message. Search in WeChat and flow the "ICSEE" official Account. notesIf the Mobile phone is set up to power saving mode, such as screen off & network off , it will not receive the message in time, Since android phones do not agree on the default handling of message interceptions, it is recommended to use WeChat receive message except the iPhone and Huawei phones. notesThe device would only send the message to the account which has the contact permission, please ensure that current account has been assigned to the contact person. 06.Bell Device Configuration If you buy a Bell Device, you can associate the Bell Device with the Video Doorbell, and the bell device will also ring when you press the bell button. F i r s t s t e p : L o n g - p r e s s t h e v o l u m e b u t t o n o f t h e Bell Device until the indicator of the bell is no longer flashing. Second step: Short-press the bell button of the Video Doorbell; if the bell is ringing at the same time, the configuration is successful. Volume button FAQ Indicator How does the device store video?
The video doorbell supports 32GB maximum TF card, which will automatically loop recording when it's fulfilled. How to fix the problem of device offline?
Check whether the device electricity is exhausted. Reconfigure the device. Check if the home network broadband is normal. How to switch the network environment?
When used in a new network environment, please long-press the RESET button for 3~5 seconds, loosen it when hear the voice prompt "restore factory settings, please don't power off". After reset successfully, configure the network again. Q:
Why does the device do not respond when press the RESET button after startup?
It needs to wait 8 seconds to press the RESET button, please wake the device startup via pressing the bell button. Q:
Why do people hover, but the doorbell did not push the alarm?
Alarm push may be turned off, or user login the device remotely already. Directions App and device firmware will have new update irregularly,you could upgrade it online at app setting,instructions are for reference only. Notice While using this product, please modify the user password. Do not install the device in damp, dusty, children easy access to the venue. Please place it under the specified condition of temperature and humidity, do not disassemble it at all. FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party. Responsible for compliance could void the users authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices). This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement:
The equipment complies with FCC Radiation exposure limits set forth for uncontrolled enviroment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Warranty Card Warranty period:one year. This warranty card is only for our company's products.