FCC ID: XCO-DYN Wireless Speaker

Xeo 10/20/30 Owners manual Hello Welcome to Dynaudio Xeo. Weve taken care of the tech;

you take care of the music. This is Xeo 9 9 Xeo 10/20/30 speakers Remote control battery Introduction Important safety instructions Removing the protection cap Packaging material Disposal Scope of delivery 10 Warning 10 10 11 Unpacking 11 11 11 12 13 Connections and control elements 13 14 14 15 Connecting and setting up 15 15 15 General settings 16 16 16 17 Operation 17 Elements on the rear panel Buttons on top of the cabinet (Xeo 10) Remote control Connecting sources directly Connecting a Bluetooth device Connecting sources via Hub or Connect Switching on Positioning and connecting to mains voltage Cloth cover Playback of connected sources Playback of a Bluetooth device Fixing the volume Standby Status LEDs on the front 17 17 18 18 19 21 Malfunctions Accessories 22 22 Desk stand 22 Wall bracket 22 23 25 Connection options 26 27 27 28 30 30 31 31 MPE Reminding 33 Technical data Division into audio zones Components of the Xeo system The Xeo system Combination examples Declaration of Conformity (EU only) Reminding (USA and Canada only) IC NOTICE VESA100 bracket (Xeo 10/20) Setting up Dynaudio Xeo 10/20/30 Introduction Thank you for choosing Dynaudio Xeo. Xeo combines the latest wireless technology with impressive sound quality and makes listening to music truly convenient and easy. The next few pages contain important information on connecting the system and its operation to ensure perfect function and the best-possible sound quality. We hope you have a great time listening to your favourite music. Dynaudio About this product The active Xeo 10/20/30 speakers are equipped with powerful integrated amplifiers and allow for the direct connection of various analog and digital audio sources. A Bluetooth interface enables the operation of Bluetooth devices and plays them back in optimal sound quality. Optional components like Xeo Hub or Dynaudio Connect enable setting up a wireless multiroom system without any restrictions to the highest sound quality. The speakers can be fully controlled with a remote control. The operational state of the system is indicated by two LEDs on the front. About this manual This manual describes the operation of the Xeo 10/20/30 speakers. Information about the optional Xeo modules (Hub, Connect, Extender, Link) can be found in the Owners manual provided with these modules. 6 7 Dynaudio Xeo 10/20/30 Important safety instructions Xeo The quintessential wireless hi-fi system Important safety instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturers instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. USA and Canada only: A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Unplug this apparatus during lightning storms or when unused for long periods of time. 13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 14. WARNING: To reduce the risk of fire or electric shock, this apparatus should not be exposed to rain or moisture and objects filled with liquids, such as vases, should not be placed on this apparatus. 15. To completely disconnect this equipment from the mains, disconnect the power supply cord plug from the receptacle. 16. The mains plug of the power supply cord shall remain readily operable. 8 9 Unpacking Warning 10 Xeo 10/20/30 speakers RISK OF ELECTRIC SHOCK! DO NOT OPEN!

If the speakers are connected to the mains voltage, a dangerous electrical voltage is present inside the speakers. Use the supplied power cable to connect the speakers to the mains voltage. Make sure that the power supply cable is not damaged; replace it with a new one if it has been damaged. To reduce the risk of electric shock, do not remove the back panel and never open the speaker housing. Do not expose the speakers to rain or moisture. No user serviceable parts inside. Refer servicing to qualified personnel. Do not operate defective speakers and disconnect defective speakers from the mains voltage. Please contact your Dynaudio Xeo distributor if you have any problems. Distributor addresses can be found on the Internet at dynaudio.com. Remote control battery DANGER OF EXPLOSION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. CHEMICAL BURN HAZARD If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. Warning / Unpacking After unpacking, make sure the system is complete and check the device and all accessories for transport damage. Transport damage may be expected if the packaging is already severely harmed. Do not attempt to start up a damaged device. If the contents are incomplete or damaged, please contact your Dynaudio Xeo distributor. Distributor addresses can be found on the Internet at dynaudio.com. Removing the protection cap The tweeter is protected by a cap to prevent damage during transport and unpacking. After you have unpacked the speaker, remove the cap by just pulling it straight out. Packaging material The packaging has been designed so that it may be reused as long as it has not been damaged during transport. Keep the packaging and use the original packaging for all further transport. Disposal Disposal of used electrical and electronic equipment (applicable in European countries with separate collection systems for this equipment) This symbol on the product or its packaging indicates that the product must not be treated as household waste. Instead, it must be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health. The recycling of materials helps to conserve natural resources. For more detailed information on recycling this product, please contact your local authority, community waste disposal office, or the shop where you purchased the product. 11 Dynaudio Xeo 10/20/30 Scope of delivery 1 2 3 4 5 6 7 2 Xeo 10/20/30 speakers 2 Xeo 10/20/30 speaker cloth covers 1 Xeo 10/20/30 remote control 2 power cables (country-specific version, length: 2.5 m) 1 stereo cable (RCA RCA, length: 1.5 m) (Xeo 10 only) 1 optical cable (Toslink Toslink, length: 1.5 m) (Xeo 10 only) 1 stereo cable mini jack (3.5 mm 3.5 mm, length: 1.5 m) (Xeo 10 only) 1 Xeo first time setup manual (quick guide for installation, not shown) Connections and control elements MUTE ON OFF 1 Line 2 Opt 3 Coax VOLUME Line 4 USB Opt Aux A B C DIRECT HUB 1 2 3 4 5 6 7 r e k a e p S n o i t i s o P Neutral Wall Corner Left Right Red Green Blue e n o Z I 1 2 3 4 Aux In R L Line In Optical In Service Mains socket II (master unit only) Scope of delivery / Connections and control elements This section describes the connections and control elements. Please contact your Dynaudio Xeo distributor if you have any problems with connection and start-up. Distributor addresses can be found on the Internet at dynaudio.com. Elements on the rear panel The Xeo 10/20/30 set consists of a master and a slave unit. The master unit carries the audio input interfaces. A:

Speaker position Sound adjustment (depending on the position of the speakers) Neutral = with free-standing placement Wall = if placed near a wall Corner = if placed in a corner Speaker placement Left = left speaker for stereo mode Right = right speaker for stereo mode B:

Speaker ID/Zone Selection of audio zones: Speakers assigned to different zones can be controlled separately via the remote control. The zones are identified as Red, Green, and Blue. C:

D:

E:

F:

Aux In: To connect an analog audio source to the speaker via mini jack. Line In To connect an analog audio source to the speaker via RCA. Optical In (Toslink):To connect a digital audio source to the speaker. USB In For firmware update only. Mains socket To connect the speaker to the mains voltage. II I A B C D E F 12 13 Dynaudio Xeo 10/20/30 Connections and control elements / Connecting and setting up Connecting and setting up Positioning and connecting to mains voltage Position the speaker in the desired location. Do not expose the speaker to direct sunlight, heat, or moisture. Do not place the speaker near devices with strong electromagnetic radiation or devices that could be destroyed or damaged by magnetic fields. Use the power cable to connect the speaker to the mains voltage. Tip Xeo 10:

For easier access, the plate at the bottom of the cabinet can be removed. Use a coin or screwdriver to loosen the screw and attach the plate after connecting the power cable. Cloth cover The cloth cover has been designed so it does not influence the sound dispersion of the speaker. It is attached to the housing with magnets and may be removed if needed. General settings In stereo mode:

Set the speaker position switch that best describes the speakers need for acoustic Select Left operating mode for the left speaker. Select Right operating mode for the right speaker. compensation. Neutral = with free-standing placement Wall = if placed near a wall Corner = if placed in a corner Select the Red, Green, or Blue zone. Select the same zone for the right and left speakers (for additional information about the audio zones, see page 26). Buttons on top of the cabinet (Xeo 10) Speaker on/off Press signal. to switch on the speakers. The Xeo 10 will scan the inputs for a Press and hold Input selection When switched on, press to switch off the speakers. to jump to another input. Volume control Press or to raise or lower the volume level. Press and hold for faster adjustment. Bluetooth pairing Press and hold both and to start pairing (see page 16). Remote control Commands will always apply to both of the speakers. MUTE ON OFF 1 Line 2 Opt 3 Coax VOLUME Line 4 USB Opt Aux A B C DIRECT HUB MUTE Muting the speakers Press to mute or unmute the Fixing the volume Press for at least 2seconds to set speakers. ON/OFF Speaker on/off Press Press to switch on the speakers. for standby mode. Press for at least 5seconds to put the speakers in sleep mode. a high volume for the speakers (see page 18). Reset Press for at least 5seconds to reset the speakers to the factory settings. VOLUME Volume control Press or to raise or lower the volume level. INPUT Signal source Press a button to select the respective signal source. selects a Bluetooth device or Hub/Connect. Controls Press to control most Bluetooth4.1 compliant devices:

Bluetooth pairing Press for at least 5seconds to enter pairing mode.

= backward,

=forward

= play or pause, 14 15 Dynaudio Xeo 10/20/30 Connecting sources directly Connect your source cables to one or more of the audio inputs Aux , Line , Opt of the master speaker (see Connection options on page 13). After it is turned on, the speaker automatically searches for an audio signal and then plays it back immediately. If several signal sources are active, one of the signal sources will be played back. Tip (Xeo 10):

For easier access, the plate at the bottom of the cabinet can be removed. Use a coin or screwdriver to loosen the screw and attach the plate after connecting the power cable. Connecting a Bluetooth device 1. To begin Bluetooth pairing, press and hold both and buttons on either one of your speakers (Xeo 10). Alternatively, hold Bluetooth Once available for pairing, the status indicator will blink white and it will be on remote for 5 seconds. available for pairing for one minute. 2. Go to settings on your device, find the Bluetooth sub-menu, and simply pair your device with your Xeo speaker by selecting Red, Green, or Blue. The speaker will store your pairing. Connecting sources via Hub or Connect Xeo Hub and Dynaudio Connect are optional components that allow you to connect analog and digital sources and are linked with your Xeospeaker via a wireless, lossless signal. For further information about the complete Xeo system, please see The Xeo system on page27. Connecting and setting up / Operation Operation Switching on To switch the speakers on from standby mode:

Press on top of one of the speakers (Xeo 10) or point the remote control at a speaker and press The speakers will automatically search for an active audio signal. If found, the

. signal will be output (autoplay function). If there is no input signal, the speakers will continue scanning the inputs for the next 20minutes and enter sleep mode. If there is no input signal, the speakers will go into standby mode after a certain period. Playback of connected sources Once you have connected your Xeo speaker with a direct input, simply choose your desired source on the remote. The speakers will automatically detect the signal and start playback. Master and slave speaker will connect wirelessly if set in the same zone. If no signal is applied to either input, the speakers will continue scanning the inputs for the next 20minutes and enter sleep mode. Playback of a Bluetooth device Once you have paired your device with your Xeo10/20/30, you can connect by choosing the Xeo10/20/30 from your list of Bluetooth devices. Select Bluetooth on the remote control and press play on your Bluetooth device. Disconnect Press and hold directly. to disconnect a connected device or disconnect from the device 16 17 Dynaudio Xeo 10/20/30 Fixing the volume You can set the speaker to a higher volume using the function to fix the volume. This setting also remains in effect in standby mode. If a signal source is connected to the Xeo10/20/30 with its own volume control, you have the option to change the output volume across a broad range with the signal source. To fix the volume:

Point the remote control at a speaker and press fixing, press one of the two volume buttons. Standby To switch speakers to sleep mode:

Point the remote control at a speaker and press for at least 2 seconds. To undo or press on top of one of the speakers. The speakers will enter sleep mode. The speakers also enter sleep mode if there is no audio signal for 20 minutes. In this mode, the wireless network is active and all connected units remain synchronized. Sleep mode power consumption is <2 W. To switch speakers to low-power standby mode:

Press and hold on the remote control for at least 5seconds. The speakers go to low-power standby mode. In this mode, the wireless network is disabled and the speakers are not connected to each other. Low-power standby mode power consumption is <0.5 W. To turn off auto standby:

Press and hold Opt on the remote control for at least 5 seconds. Fixing the volume Status LEDs on the front The two LEDs in the upper left corner of the cabinet front indicate the operational state of the speakers and system with various colours and blinking functions. On-state Illuminated in blue On-state Slow blinking in blue On-state Illuminated in purple On-state Slow blinking in purple Connection Slow blinking in red The speaker is switched on, connected to a Hub or Connect, and an audio signal is played back. The speaker is switched on, connected to a Hub or Connect, but an audio signal cannot be found. The speaker is switched on, connected to a local input, and an audio signal is played back. The speaker is switched on, connected to a local input, but an audio signal cannot be found. There is no active transmitter2)/master or no connection possible. Search Fast blinking in blue for 20min Searching for an active input. Synchronization/

Connection Fast blinking in red for 10s System synchronization during no transmitter2)/master connection. Blue LED is turned off for 0.2s New transmitter2) ID, transmitter2) input, or direct input is selected. Illuminated in red for 5s Receiver mode is changing. Illuminated in white Bluetooth connection is established. Slow blinking in white Speaker is in pairing mode. Firmware loading White LED: slow to fast blinking Firmware is being loaded. during the load sequence, Red LED: illuminated Volume Fast blinking in blue Volume is being adjusted. Mute Fading in and out Speaker is muted. Off-state Illuminated dimly in red Speaker is in standby mode. 1) depending on the resolution of the audio source, 2) Hub, Connect, mobile device, etc. LED blinking code off Illuminated in white Illuminated in a colour Slow blinking

(1 or 2 Hz) Fast blinking

(3 or 4 Hz) 18 19 Dynaudio Xeo 10/20/30 Dynaudio Xeo 10/20/30 Malfunctions Malfunctions Interruptions, clicking noises, or other audible interference when playing music is usually not caused by radio transmission in the Xeo system. Often, other external causes influence the transmission quality. Below are a few tips for improving transmission quality:

1. Position all radio transmitters and receivers away from each other. WLAN devices, radio receivers, and radio systems may influence each other if they are too close together. Test out various locations for each device. 2. Switch off the automatic search function in WLAN devices. WLAN devices and other radio systems permanently scan for available frequencies, thus sending signals that could disrupt other radio systems. This automatic search function can usually be switched off. 3. Xeo technology radio signals can, of course, transmit through walls. However, walls may consist of very different materials, such as wood fibreboard, stone, or even steel. The walls may also contain complex cable installations for electrics, phones, TVs, and radios, as well as water pipes and air shafts. These can divert radio signals. This is why you should test different locations for the Xeo Hub, Extender, and Link and favour the most direct radio path between the Xeo components. 4. Some electrical devices, such as microwaves, generate strong electromagnetic fields that could disrupt radio systems. Do not operate such electrical devices near Xeo components. You can ask your Dynaudio Xeo distributor for assistance at any time Or go to dynaudio.com/support to read the FAQ or to contact the Customer Support Team. Further information can also be found on the Xeo website at dynaudio.com/xeo 20 21 Accessories / Setting up Accessories Accessories (Xeo 10) A desk stand or wall brackets extend the range of applications of your Xeo10 speakers. For further information, please see the website at dynaudio.com or contact your Dynaudio distributor. Distributor addresses can also be found at dynaudio.com Desk stand The Dynaudio desk stand for Xeo10 is an elegantly designed stand for placing the speakers on a desk or shelf. A installation instruction is provided with the stand. Wall bracket The wall bracket allows you to mount the Xeo10 speakers on the wall. VESA100 bracket

(Xeo 10/20) VESA is a standard for wall brackets developed by the Video Electronics Standards Association. The Xeo10 and Xeo 20 speakers allow you to mount brackets according to the VESA100 standard. This means that the screws on the back plate are spaced 100mm apart. To mount a VESA100 bracket

(Xeo 10):

1. Loosen the four screws (Torx type) and unmount the back plate. 2. Keep the back plate for future use. Follow the instructions provided with the bracket you want to mount. Setting up Spikes with pointed ends Xeo 30 floor-standing speakers are delivered with spikes for permanent installation on the floor. The pointed ends of the spikes may result in injuries and damage delicate floors. Pay attention that you do not injure yourself with the spikes. We recommend inserting the spikes in aluminium feet if you have delicate floors, such as parquet or laminate. Position the speaker in the desired location. Do not expose the speakers to direct sunlight, heat, or moisture. Do not place the speakers near devices with strong electromagnetic radiation or devices that could be destroyed or damaged by magnetic fields. 22 23 Dynaudio Xeo 10/20/30 Dynaudio Xeo 10/20/30 Connection options Connect your signal source to the appropriate input on the Xeo10/20/30 speaker. Following table gives a selection of signal sources and options for connecting to the Xeospeaker. Connection options Smartphone, other portable devices Headphones Your signal source Notebook, Mac, PC Astell&Kern PonoPlayer Docking station, network client, Sonos, Bluesound, etc. Google Chromecast Audio Apple AirPort Express Apple TV*

Hard disk, network player, CD player Analog radio, digital radio Analog record player TV Stereo preamplifier Stereo power amplifier Subwoofer Signal source output Xeo10/20/30 input*

Cable

(source Xeo10/20/30) Notes Optical*

Line out Headphones Headphones Optical Jack Line out Optical*

Line out Optical Optical Optical Line out Optical*

Line out Optical*

Line out*

Headphones Line out Optical*

Optical In Toslink Toslink

* If available Line in Aux in Aux in Aux in RCA RCA Jack 3.5 mm 3.5 mm Jack 3.5 mm 3.5 mm Jack 3.5 mm 3.5 mm Optical In Toslink Toslink Aux in Line in Jack 3.5 mm 3.5 mm RCA RCA Optical In Toslink Toslink

* If available Aux in Optical In Optical In Optical In Line in Jack 3.5 mm 3.5 mm Select a variant. Mini Toslink Toslink Mini Toslink Toslink Toslink Toslink RCA RCA

* up to 3rd generation

* If available Optical In Toslink Toslink Line in RCA RCA Optical In Toslink Toslink

* If available Line in Aux in Line in RCA RCA

* On phono preamplifier Jack 3.5 mm 3.5 mm Select a variant. RCA RCA Optical In Toslink Toslink Pre-out, main out Tape out Pre-out, main out*

Second pre-out Analog output Line in Line in Line in Line in Line in RCA RCA RCA RCA RCA RCA RCA RCA RCA RCA

* If available

* Disconnect bridge 25 24 AV receiver, AV processor Optical Optical In Toslink Toslink Pre-out, main out Line in RCA RCA Division into audio zones The Xeo speakers (as well as Xeo Link) can be assigned to audio zones using the Zone selector switch. All components assigned to the same zone can be operated together via the remote control. Red Green Blue e n o Z Red Green Blue e n o Z Red Green Blue e n o Z Green Blue Red The picture shows a possible zone configuration. Connection options The Xeo system Xeo consists of several high-quality components that are optimally matched. When combined, they can fulfil the most demanding requirements for a wireless multi-room and multi-source system. Components of the Xeo system Xeo speakers MUTE ON OFF 1 Line 2 Opt 3 Coax VOLUME Line 4 USB Opt Aux A B C DIRECT HUB Xeo remote control Dynaudio Connect and Xeo Hub Xeo Extender Xeo Link The active Xeo speakers Xeo10/20/30 receive the wireless signals from the Hub or Connect and play them back in optimal sound quality. In addition, the Xeo10/20/30 can be connected directly to various audio sources. All speakers have an integrated amplifier and can be controlled with a remote control. Display elements indicate the operating state of the system and controls on the cabinet let you switch it on/off or change the volume without using the remote control. The Xeo remote control can be used to turn the speakers on and off, change the volume, and select a Hub or Connect and its connected signal sources. The Dynaudio Connect and Xeo Hub are the control centres for the Xeo system. Both offer a new level of wireless connectivity and convenience. Signal sources such as tuners, receivers, CD players, TVs, streaming clients, network players, MP3 players, or computers are connected to them. Signals are sent wirelessly and lossless to the connected Xeo or Focus XD speakers (or Xeo Link) where they are then played back. The Xeo Extender extends the reception range of the Xeo Hub. As a result, Xeo speakers or other Xeo components can be operated further away from the Xeo Hub or Dynaudio Connect. The Xeo Link receives wireless signals from a Xeo Hub or Dynaudio Connect and outputs analog and digital signals from its connections. As a result, you can also connect active subwoofers, active speakers, or other components to the Xeo system. 26 27 Dynaudio Xeo 10/20/30 Connection options For extended range:

Analog/digital audio sources

+ Hub or Connect + Extender + Xeo speaker For additional speakers:

Analog/digital audio sources

+ Hub or Connect + Xeo speaker plus

+ Link + active component (e.g. active subwoofer, active speakers, or power amplifier and passive speakers) Combination examples Below you will find several examples of Xeo component combinations. The high level of flexibility in the Xeo system enables even more variants. Ask your Dynaudio distributor to find the perfect solution for your needs. Direct wired:

Analog/digital audio sources

+ Xeo 10/20/30 Direct wireless:

Bluetooth device (mobile phone, etc.)

+ Xeo 10/20/30 With Hub or Connect:

Analog/digital audio sources

+ Hub or Connect + Xeo speaker 28 Note: The Extender and Link may also be combined. 29 Dynaudio Xeo 10/20/30 Declaration of Conformity (EU only) Dynaudio A/S hereby declares, that the product Dynaudio Xeo 10 / Xeo 20 / Xeo 30 is in conformity with the following directives:

2001/95/EF (Product Safety) 2014/53/EU (RE directive) 2014/30/EU (EMC directive) 2011/65/EU (ROHS directive) 1275/2008 (ErP, Ecodesign directive) The Declaration of Conformity is available on the Internet at dynaudio.com/

support/manuals Reminding (USA and Canada only) A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme Ia section 15 des rglementations de Ia FCC. Le fonctionnement de lappareil est sujet aux deux conditions suivantes:

30

(1) cet appareil ne doit pas provoquer dinterfrences nfastes, et (2) cet appareil doit tolrer les interfrences reues, y compris celles qui risquent de provoquer un fonctionnement indsirable. Note: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body. IC NOTICE This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radioexempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformment la rglementation dIndustrie Canada, le prsent metteur radio peut fonctionner avec une antenne dun type et dun gain maximal (ou infrieur) approuv pour lmetteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique lintention des autres utilisateurs, il faut choisir le type dantenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas lintensit ncessaire ltablissement dune communication satisfaisante. MPE Reminding

(i) The device for operation in the band 51505250MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

(ii) The maximum antenna gain permitted for devices in the bands 52505350MHz and 54705725MHz shall comply with the e.i.r.p. limit; and

(ii1) The maximum antenna gain permitted for devices in the band 57255825MHz shall comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate. Connection options Cet quipement doit tre installe et utilis une distance minimale de 20cm entre le radiateur et votre corps.

(i) Tout appareil destin la bande 51505250MHz devra tre exclusivement utilis en intrieur a fin de rduire les risques de perturbations lectromagntiques gnantes sur les systmes de satellite mobile dans un mme canal.

(ii) Les radars forte puissance sont dsigns comme les utilisateurs principaux (cest--dire quils sont prioritaires) des bandes 52505350MHz et

(iii) 56505850MHz. IIs peuvent provoquer des perturbations lectromagntiques sur les appareils de type LELAN (rseau de communication local sans licence) ou les endommager. 31 Dynaudio Xeo 10/20/30 Dynaudio Xeo 10/20/30 Technical data Technical data Data Analog inputs Digital inputs Wireless Frequency response ( 3 dB) Box principle Crossover Crossover frequencies Woofer Midrange Tweeter Amplifier power AC power input Xeo 30 Xeo 20 Xeo 10 Mini-Jack, RCA stereo Mini-Jack, RCA stereo Mini-Jack, RCA stereo Toslink 24bit / 96kHz 36Hz - 21kHz Bass Reflex Toslink 24bit / 96kHz 40Hz - 21kHz Bass Reflex Toslink 24bit / 96kHz 40Hz - 21kHz Bass Reflex 2-way DSP based 2-way DSP Based 2-way DSP Based 200/4300Hz 2x14cm MSP

-

4700Hz 14cm MSP

-

5000Hz 14cm MSP

-

28mm soft dome 28mm soft dome 28mm soft dome 3x65W 2x65W 2x65W 100V - 240V, 50/60Hz 100V - 240V, 50/60Hz 100V - 240V, 50/60Hz Standby power consumption Maximum power consumption

<0.5W 165W Weight Dimensions (WxHxD) 13.4kg / 29.5lbs 180x825x246mm 7.1x32.5x9.7in Dimensions with feet/grille (WxHxD) 228x852x275mm 9.0x33.5x10.8in

<0.5W 100W 6.2kg / 13.7lbs 180x320x257mm 7.1x12.6x10.1in 180x320x265mm 7.1x12.6x10.4in

<0.5W 100W 4kg / 8.8lb 173x255x154mm 6.8x10x6.1in 173x255x164mm 6.8x10x6.5in 33 All Apple products are trademarks of Apple Inc. All Sony products are trademarks of Sony Electronics Inc. All Sonos products are trademarks of Sonos Inc. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. All Google products are trademarks of Google Inc. Other trademarks and trade names are those of their respective owners. An update to this manual may be necessary due to product improvements and new functions. The latest version of this manual is available on the Internet at dynaudio.com/support/manuals 32 30 Xeo 10/20/30 Designed and engineered by Dynaudio Labs in Denmark Dynaudio A/S 8660 Skanderborg Denmark dynaudio.com Owners manual Xeo 10/20/30, EN - Item no. 45563101C. All text and image copyrights reserved. Subject to change without notice.