Start_Guide_Dynaudio_Connect_PRESS_with_fold-guide.pdf 1 03/02/15 13.05 Dynaudio Connect i e d u g t r a t S Rearplate and bottom EF B D 1 2 3 4 PC/Mac Sound Card Bluetooth Setup WiFi Setup A B C Aux In R L Line In Optical In Coax In USB In Id Service 5V DC 2A C A Bluetooth Not Connected Connected Pairing Mode High Resolution 1 Zone 24 Bit / 96 kHz Multiroom 3 Zones 16 Bit / 48 kHz WiFi Not Connected Connected Slow Blinking:
Acess Point Mode Fast Blinking:
WPS Mode Important! Make sure you have the latest firmware update. Visit dynaudio.com/support Model: Dynaudio Connect, ID 4573141 Dynaudio A/S, Sverigesvej 15, DK-8660 Skanderborg This device complies with Part 15 of the FCC Rules. Its operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. CAN ICES-3 (B)/NMB-3(B) Contains FCC ID:XCO-HSDWAM83 IC:7756A-HSDWAM83 1 Basic setup A B C D Set the broadcast mode of Dynaudio Connect to multiroom mode or hi-res mode. Note that Xeo 4/6 speakers do not support hi-res broadcast. Set the Id switch on rearplate to A, B or C. Connect your source(s) on the rearplate. Connect power to the device. Wait 30 sec. Connect power to your speakers. Power ON speakers. Select A, B or C on your remote control, make sure it matches to your settings on the Dynaudio Connect, either A, B or C. Choose input 1-4 on the remote. C M Y CM MY CY CMY K 1 2 3 4 A B C Remote 2 WiFi-setup 1 F Press-and-hold the WiFi setup button for 3 seconds to make the Dynaudio Connect searchable from an external device (the WiFi light on the front starts blinking slowly). 2 Find Dynaudio Connect in your list of WiFi devices and connect to it. 3 Please go to the website:
http://192.168.1.1 and follow the setup wizard to connect to your home network. WiFi-setup Dynaudio Connect | A F (3 sec.) 3 4 PC/Mac Sound Card Bluetooth Setup WiFi Setup A B C Optical In Coax In USB In Id Service 5V DC 2A 192.168.1.1 Network configuration Connection Status:
Dynaudio Connect | A Mac Adress:
CC:90:93:05:2A:6C Airplay Device Name:
Dynaudio Connect | A Wireless LAN Settings Service Set ID (SSID) 2,4GHzCisco00589(NONE) Apply Advanced Settings Status indicator:
Not Connected Fast Blinking: WPS Mode Connected Slow Blinking: Acess Point Mode When playing via WiFi - select channel 4 on your remote 3 Bluetooth setup E Bluetooth pairing is done by pressing the Bluetooth button on the rearplate and connecting your Bluetooth device within 1 min. Status indicator:
Pairing Mode Not Connected When playing via Bluetooth - select channel 4 on your remote Connected Find latest manuel on dynaudio.com/support Start_Guide_Dynaudio_Connect_PRESS_with_fold-guide.pdf 2 03/02/15 13.05 Unpacking After unpacking, make sure the system is complete and check the device and all accessories for transport damage. Transport damage may be expected if the packaging is severely harmed. Do not attempt to commission a damaged device. If the contents are incomplete or damaged, please contact your Dynaudio distributor. Distributor addresses can be found in the Internet at www.dynaudio.com Packaging material The packaging has been designed so that it may be reused if it was not damaged during transport. Do not throw away the packaging and use the original packaging for all further transport. Disposal Disposal of Old Electrical & Electronic Equipment
(Applicable in European countries with separate collection systems) This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. Safety information Dynaudio Connect power supply unit Use only the delivered power supply for this device Make sure that the power supply cable to Dynaudio Connect is not damaged. Exchange the power supply unit for new one if it has been damaged. Power requirement for Dynaudio Connect power supply is 5VDC, 2A during normal operation. This device cannot be properly powered by audio USB input due to high power requirements. Reminding This device complies with Part 15 of the FCC Rules. Its operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la section 15 des rglementations de la FCC. Le fonctionnement de lappareil est sujetaux deux conditions suivantes : (1) cet appareil ne doit pas provoquer dinterfrences nfastes, et (2) cet appareil doit tolrer les interfrences reues, y compris celles qui risquent de provoquer un fonctionnement indsirable. Note: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This product generates, uses, and can radiate radio fre- quency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is Increase the separation between the equipment and receiver. connected. Consult the dealer or an experienced radio/TV technician for help. C M Y CM MY CY CMY K Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. IC NOTICE This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radioexempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. MPE Reminding This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body. Cet quipement doit tre install et utilis une distance minimale de 20 cm entre le radiateur et votre corps.
(i) The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
(ii) The maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall comply with the e.i.r.p. limit; and
(iii) The maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non point- to-point operation as appropriate.
(i) Tout appareil destin la bande 5150-5250 MHz devra tre exclusivement utilis en intrieur afin de rduire les risques de pertuarbations lectromagn- tiques gnantes sur les systmes de satellite mobile dans un mme canal.
(ii) Les radars forte puissance sont dsigns comme les utilisateurs principaux (cest--dire quils sont prioritaires) des bandes 5250-5350 MHz et
(iii) 5650-5850 MHz. Ils peuvent provoquer des pertur- bations lectromagn- tiques sur les appareils de type LELAN (rseau de communication local sans licence) ou les endommager. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. The plug of external power supply unit is used as the disconnect device, it shall remain readily operable. The USB socket on rearplate marked with label Service is for firmware upgrade purpose only. Enjoy!