FCC ID: 2AVNLGGBD01001 Bionic Flapping-wing Bird

Go Go Bird User Manual 1 How to remove and charge lithium battery a. Turn o the switch at the bottom of Go Go Bird, pull out lithium battery from the tail of Go Go Bird, refer to gure 1. Pull out On/o switch Lithium battery Figure 1 b. Plug lithium battery directly into USB charger, charger can be connected to adaptor, computer etc., DC 5.0V power supply, refer to gure 2. USB Charger Lithium battery Figure 2 c. The green signal light of the charger is on, indicating that power is on; after inserting lithium battery, red signal light is on, indicating that the battery is charging; red signal light is o, indicating that the lithium battery is full. d. After charging nished, unplug the charger from DC 5.0V power supply and extract the lithium battery promptly. e. Plug the full lithium battery into the battery container, tail of Go Go Bird, pay attention to the insertion direction, refer to gure 3. Figure 3 2 How to insert and remove AAA batteries of remote control a. Turn o the switch of the remote control, extract the battery cover,refer to gure 4. b. Insert two 1.5V AAA batteries correctly based on polarity identication into battery compartment. c. Reload battery cover, it is loaded correctly when you hear a slight click. Remote control will automatically turn o in ten minutes when not in use. d. For AAA batteries that running out of power, please remove from battery cover. Figure 4 3 How to pair Go Go Bird with remote control Go Go bird already matched when leaving factory, if remote control can connect with Go Go Bird, please ignore this step. If not, please refer to below pairing steps. a. Turn on the switch of Go Go Bird and place the remote control close to Go Go Bird. b. Press the function button and turn around button (B) of the remote control at the same time (remote control should be o), then press the switch button of remote control, then the signal light of remote control will be on,refer to gure 5. c. Pay attention to the signal light of Go Go Bird, if the signal light is ashing, indicating that the pairing matching is successful. If fail to match, please repeat above steps. Function button On/o switch Turn around button Signal light Figure 5 4 How to monitor remote control a. Pull up the rocker (upwards), Go Go Bird will speed up; move down the rocker (downwards), Go Go Bird will slow down, refer to gure 6. b. Move the rocker to the left (left), Go Go Bird will turn left; move the rocker to the right (right), Go Go Bird will turn right. c. Press the button A, Go Go Bird will keep ying in circle counter clockwise; press button Y, Go Go Bird will keep ying in circle clockwise. d. Press button B, Go Go Bird will turn around. When Go Go Bird is ying, press button X, Go Go Bird will descend. e. The IR evading obstacle function, as default setting, will be on when Go Go Bird y. You can turn on/o this IR evading obstacle function by pressing function button and turn around (B) button of remote control at the same time for better user experience. Pull up Turn left Turn right Move down Figure 6 X: take-o/landing A: Counter clockwise Y: Clockwise B: turn around 5 How to y Go Go Bird The right way to hold Go Go Bird, refer to gure 7. Figure 7 How to take o:

Method 1. By somatosensory switch: Turn on the switch of Go Go Bird, hold Go Go Bird on horizontal level, sway up-and-down, wings start to ap then release, Go Go Bird will y away. Method 2. By remote control: Turn on the switch of Go Go Bird and remote control, hold Go Go Bird on horizontal level, press button X of remote control, wings start to ap then release, Go Go Bird will y away. a. The default altitude setting is to y straight, after Go Go Bird y away, please use remote control rocker to monitor the direction. b. Go Go Bird is with altitude hold sensor, when you y Go Go Bird, please hold it higher with your hand then release, Go Go Bird will be on auto y mode. Then please use remote control to monitor. 6 Malfunction & solution No response when turn on the remote control Solution: Double check whether AAA batteries install correctly according to the polarity identication, or replace with new batteries. No response or lack of power when turn on Go Go Bird Solution: Make sure the lithium battery of Go Go Bird is fully charged. Remote control fail to connect with Go Go Bird Solution: Turn o Go Go Bird and remote control, repeat the pairing steps. 7 Short-range wireless transmission equipment Product nameBionic apping-wing bird Type of emissionsSRD Frequency2424MHz-2472MHz 8 Warnings a. When you take out Go Go Bird from the box, try not to grab the wings and tails, keep Go Go Bird away from thermal source, sharp objects. b. For multiple Go Go Bird playing, please pair one with one individually, do not turn on the switch of two Go Go Birds and pair at the same time. c. Please keep Go Go Bird within your sight when Go Go Bird is ying. When Go Go Bird is on ying mode, keep Go Go Bird away from water, trees, high voltage wire etc,. d. Press on/o or button X in emergency, Go Go Bird will stop ying immediately and drop on the ground. Please check the wires, plug, shell and other parts regularly. If there is any damage please stop using until it is xed completely. e. Please use the customized lithium batteries that come with Go Go Bird only. Do not match with other lithium batteries. Rechargeable batteries are only to be charged under adult supervision. Rechargeable batteries are to be removed from the toy before being charged. f. AAA batteries are to be inserted into remote control with the correct polarity. Non-chargeable batteries are not to be charged. Dierent types of batteries or new and used batteries are not to be mixed. Exhausted batteries are to be removed from the toy. The supply terminals are not to be short-circuited. Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries. g. This product is not suitable for children under 3 years old. Please keep the user manual and package box at all times since they contain important information. h. Any Changes or modications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. i. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. j. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. k. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body Apply only to Bionic apping-wing bird. l. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 0-3 FCC ID:2AVNLGGBD01001Bionic flapping-wing bird FCC ID:2AVNLFYC001001Wireless Remote Controller 211-200310 DISTRIBUTOR XTREM Toys & Sports GmbH Address: Blocksbergstrae 173, 66955 Pirmasens, Germany. Telephone: +49 (0) 6331 / 60 89 5-0

Bionic flapping-wing bird vero ROHS Battery:3 7V==100mAh Hanwang Technology Co,, Ltd. Madein China FCCID:2AVNLGGBDO1001

(R]211-200310

Company: Hanwang Technology Co., Ltd. Add: 3rd Floor, Building 5, No. 8 Dongbeiwang West Road, Haidian District, Beijing, China Tel: 010-82788546 Email: chenxuehui@hanwang.com.cn DATE:2020-03-09 FCC Authorization FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern:

We Hanwang Technology Co., Ltd.,Hereby authorizes Bay Area Compliance Laboratory Corp. to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Bay Area Compliance Laboratory Corp. on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, This authorization is valid until further written notice from the applicant. 21 U.S.C. 862. Sincerely Signature:

Printed Name: Xuehui Chen Title: Certification Manager QA-FR-170-B 7/29/2014

Company: Hanwang Technology Co., Ltd. Add: 3rd Floor, Building 5, No. 8 Dongbeiwang West Road, Haidian District, Beijing, China Tel: 010-82788546 Email: chenxuehui@hanwang.com.cn DATE:2020-1-20 DECLARATION OF SIMILARITY FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Dear Sir or Madam:

We Hanwang Technology Co., Ltd., Hereby declare that product: Bionic flapping-wing bird,model(s): GoGoBird 102,GoGoBird 103,GoGoBird 201, GoGoBird 202, GoGoBird 203, GoGoBird 301,GoGoBird 302, GoGoBird 303, GoGoBird 401, GoGoBird 402,GoGoBird 403, GoGoBird 501, GoGoBird 502, GoGoBird 503, GoGoBird 601,GoGoBird 602,GoGoBird 603, GoGoBird 701,GoGoBird 702, GoGoBird 703,GoGoBird 801,GoGoBird 802, GoGoBird 803,GoGoBird 0101,GoGoBird 001 are electrically identical with the model GoGoBird 101 that was tested by BACL.FCC ID: 2AVNLGGBD01001. The differences between the tested model and multiple models are as follows:

They have the same PCB layout and schematic, just have different model name for marketing purpose. Please contact me should there be need for any additional clarification or information. Best Regards, Signature:

Printed Name: Xuehui Chen Title: Certification Manager

Company: Hanwang Technology Co., Ltd. Add: 3rd Floor, Building 5, No. 8 Dongbeiwang West Road, Haidian District, Beijing, China Tel: 010-82788546 Email: chenxuehui@hanwang.com.cn DATE:2020-03-09 FCC Confidential Authorization FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: 2AVNLGGBD01001 In accordance with Sections 0.457 and 0.459 of the Commissions Rules, Hanwang Technology Co., Ltd. hereby requests long-term confidential treatment of information accompanying this application as outlined below:

Block Diagram Schematics Operation Description The above materials contain proprietary and confidential information not customarily released to the public.The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely, Signature:

Printed Name: Xuehui Chen Title: Certification Manager QA-FR-171-A