FCC ID: 2AVB7-0007 Healy Watch

Healy Watch INSTRUCTIONS FOR USE Model No.: 0007 EN | Table of Contents 1. Introduction 2. General 2.1 Intended Use 2.2 Description 2.2.1 Hardware Description 2.2.2 Software Description 2.3 Attention 2.4 Safety Notes 3. Preparations for Use 3.1 Installation 3.1.1 Smartphone Requirements 3.1.2 Android Operating System 3.1.3 iOS Operating System 3.1.4 Hardware 3.1.5 Pairing via Bluetooth 3.1.6 Wearing the Healy Watch 4. Operation Instructions 4.1 Software Functions 5. Cleaning, Disinfection and Maintenance 5.1 General 5.2 Cleaning 5.3 Storage Between Applications 3 | EN 4 4 4 4 5 5 6 6 7 7 7 7 7 8 10 12 12 13 14 14 14 14 Healy Watch Instructions for Use 5.4 Maintenance 5.5 Troubleshooting 6. System Components 7. Technical Data 7.1 General 7.2 Electrical Parameters 7.2.1 Power Source Requirements 7.2.2 Healy Watch 7.2.3 FCC Statement 7.3 EC-Declaration of Conformity 7.4 Mechanical Parameters 7.5 Environmental Conditions 7.5.1 Operation and Storage 8. Disposal 9. Used Symbols and Icons 10. Revision Status 15 15 16 16 16 17 17 17 18 19 20 20 20 20 20 22 Disclaimer: The Healy Watch is not intended to cure, treat, mitigate, diagnose or prevent disease, but rather to support vitality and wellbeing. EN | 4 1. Introduction Thank you for choosing the Healy Watch. Please read this manual carefully and pay special attention to the warnings and cautions. This manual is intended for the user. Intended users include adults at home. It aims to ensure safe handling and to enable users to become familiar with the device. 2. General 2.1 Intended Use Healy Watch is a tracker for wellbeing. 2.2 Description The Healy Watch is a portable device, internally powered and controlled via Bluetooth by a software application that is in-

stalled on a smartphone. The charging of the internal battery is done through the USB port. The Healy Watch App" software application is necessary for configuration and control of the Healy Watch. The Healy Watch App" is available in the Google Play Store and the Ap-

ple App Store. 5 | EN 2.2.1 Hardware Description Removable straps Wrist pads Full-screen touch display Sensor Sensor Sensor Built-In USB charger 2.2.2 Software Description The "Healy Watch App" is required for configuring and con-

trolling the Healy Watch hardware. EN | 6 2.3 Attention Intentional misuse may impair the function of the device. Carefully read the instructions before using the device. This product is intended only for the purpose described in these ins tructions for use. In this manual, the word DANGER warns of possible person-

al injury!

In this manual, the word WARNING warns of possible dam-

age to objects. 2.4 Safety Notes Danger/Warning:

Do not immerse the device in liquids. In the case of a defect please contact the manufacturer. Any attempt to repair the device will void the warranty. The device should only be stored and transported under the conditions defined in these instructions. To protect the device against contamination and damage, keep it locked and away from children, dust, sunlight, mois-

ture, pets and vermin. Do not carry out maintenance while the equipment is in use. CHOKING HARZARD -- Small parts NOT for children under 3 years. 7 | EN 3. Preparations for Use 3.1 Installation Before putting the Healy Watch into operation, you need to prepare the hardware and install the "Healy Watch App". Bluetooth 4.2 or higher iOS1 version 9.0 or higher Android2 version 4.4 or higher 3.1.1 Smartphone Requirements Bluetooth Operating system 1 iOS is a registered trademark of the operating system for smartphones and devices manufactured by Apple Inc. 2 Android is a registered trademark of Google Inc. for the operating system for smartphones and other devices 3.1.2 Android Operating System Open the Play Store3 Search for the Healy Watch App"

Select "Healy Watch App"

Download and install on your smartphone 3.1.3 iOS Operating System Open the Apple Store4 Search for the "Healy Watch App"

Select "Healy Watch App"

Download and install on your smartphone 3 Play Store is the trademark of Google Inc. 4 App Store is the trademark of Apple Inc. EN | 8 3.1.4 Hardware Unpack the Healy Watch and check for damage Charge the batteries for 1.0 hours before first use Note: The battery cannot be removed by the user. 1 Gently pull the straps off. OPEN Do NOT pull the straps horizontally 9 | EN 2 Insert the built-in USB charger into a USB port for charging. 3 Remove device from the power supply once fully charged. 4 Push the straps back on. EN | 10 3.1.5 Pairing via Bluetooth 1 Log into your Healy account. 2 Read and agree to terms and policies. 3 Set up account information:

profile photo, name, gender etc. 4 Make sure the smartphone Bluetooth (BLE 4.2) and location service are turned on. 5 Go toSettings Pair Deviceand select the Healy Watch for pairing. You can check the Healy Watch Bluetooth ID inFunction Info. 6 Pair the Healy Watch with your smartphone. 7 Firmware Update: before using the Healy Watch, go to Setting Firmware Updateand upgrade the firmware if there is a new version available. 11 | EN 5 6 7 EN | 12 3.1.6 Wearing the Healy Watch For accurate heart rate* measurement, please wear the watch:

1 Tightly but comfortably. It should not move while running or exercising. 2 Keep it at least one finger width away from the carpal bones.

* Not intended for diagnosis or therapy 4. Operation Instructions 1 Swipe - Swipe up and down on the touchscreen to scroll through widgets and menu options. 2 Tap - Tap the button to execute the function. 3 Long Press - Long press for 2 second to activate the func-

tions: Power Off, Send SOS. 13 | EN 4 Wrist Gesture - Rotate or lift your wrist toward your body to turn the screen on. 4.1 Software Functions Watch Face The Healy Watch updates the time and date automatically when you sync with a smartphone. Status The total number of steps, cal-

ories, distance, active minutes and goal achievement in % that you have achieved in a day. Sleep The watch automatically records your sleeping hours, heart rate*, and sleep quality while youre wearing it. Work Out 10 different sport modes in-

cluding run, cycle, gym, basketball etc. Tap to start recording your workout. Function Set your watch and tap into smart features including vibration alarm, timer, music control, weather etc. Breath The Healy Watch helps you calm down with 3 levels of breathing exercises. EN | 14 Message Check the 10 latest messages from your calls, SMS text, WeChat, WhatsApp, Facebook and more. SOS Long press for 2 seconds to send SOS messages with your location to your emer-

gency contacts in SMS form.

* Not intended for diagnosis or therapy 5. Cleaning, Disinfection and Maintenance 5.1 General Maintenance activities increase the lifespan and safety of the Healy Watch. Please read this section carefully. 5.2 Cleaning Switch off the Healy Watch before cleaning. For cleaning, com-

mercial cleaning products may be used. The surfaces can be wiped with a damp sponge or cloth. Make sure that no liquid penetrates beneath the covers or enclosures. Caution: Do not use cleaning agents containing solvents

(e.g. acetone or nail polish) or abrasive cleaners as they will damage the surface of the device. 5.3 Storage Between Applications After application, store the device in a cool and dry location and protect against direct sunlight. 15 | EN 5.4 Maintenance There are no user serviceable parts inside. In the event of damage, please contact the manufacturer. The following maintenance activity is recommended and should be followed for safe operation. Frequency By whom Maintenance activity Prior to each use User Check the casing for damage. In case of damage contact the manufacturer or an authorized dealer 5.5 Troubleshooting Below you will find typical warnings or messages that are re-

lated to the app or hardware. If you experience a situation that is not listed here or a problem persists, please contact the manufacturer. Event or message Cause Actions required No connection from the smart-

phone to the device No connection from the smart-

phone to the device Device is switched off Bluetooth in your smart-

phone is deac-

tivated Switch on the device and re-

start the App Open connec-

tivity settings and acti vate Bluetooth EN | 16 Event or message Cause No connection from the smart-

phone to the device Location ser-

vice is disa-

bled. Actions required Enable location service 6. System Components Reference number Description 0007 Healy Watch hardware device 108-1301 Screen protector 108-1302 Screen wipe 108-1303 Conductive gel Quantity 1 1 1 1 7. Technical Data 7.1 General Protection against ingress of water and particulate matters IP 67, dustproof, complete protec-

tion against contact, protection against temporary submersion 17 | EN 7.2 Electrical Parameters 7.2.1 Power Source Requirements The Healy Watch can be connected to any power source with the following specifications:

Supply voltage range 4.4 V 5.5 V DC Output current Max. 2500 mA Frequency Socket type Power type DC USB-Type A High powered 500 mA or higher Insulation type Double or reinforced insulation 7.2.2 Healy Watch Input voltage Input current Protection class See 7.2.1 20 mA IP 67 Battery capacity 130 mAh EN | 18 7.2.3 FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interfe rence received, includ-ing interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide rea-

sonable protection against harmful interference in a residen-

tial installation. This equipment generates, uses and can ra-

diate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interfer-

ence to radio communications. However, there is no guaran-

tee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 19 | EN 7.3 EC-Declaration of Conformity This is an electrical device for application on humans. Type: Healy Watch Year of manufacture: 09-2019 12-2019 The product is designed and manufactured in accordance with the following directives:

Low Voltage Directive 2014/35/EU ROHS - Directive 2011/65/EU; REACH 1907/2006/EC under the sole responsibility of:

Company: Healy GmbH |Schloss Krnzlin|

Darritzer Str. 6|16818 Krnzlin Germany The device complies with the following applicable standards:

EN62479:2010; EN60950-1:2006+A11:2009+A1:2010+A12:

2011+A2:2013; Draft EN301 489-17 V3.2.0 (2017-03); Draft EN 301 489-1 V2.2.1 (2019-03); EN300 328 V2.2.2 (2019-07);

IEC62321-series The technical documentation with risk analysis is completely available. The instructions for use accompanying the product are available in the respective national language. Krnzlin/09.09.2019 Place/date Signature CEO EN | 20 7.4 Mechanical Parameters Dimensions 11.6 x 2.2 x 12.4 cm Weight Strap Input socket 30 g TPU black USB 7.5 Environmental Conditions 7.5.1 Operation and Storage Temperature Range 5C to 40C / 41F to 104F Relative humidity 15 % to 93 %

Atmospheric pressure 700 hPa to 1060 hPa 8. Disposal The expected service life is 5 years. Ask your local authority for recycling advice. 9. Used Symbols and Icons The following icons are used on the device, the packaging and the labelling:

21 | EN Watch Face Status Sleep Function Message Bluetooth Work Out Breath SOS Recycling symbol In conformity with European legis lation REF 0006Hardware reference number Symbol for Bluetooth wireless connection Electronic waste do not dispose. Recycle acc. to local regulations or contact your authorized dealer or the manufacturer EN | 22 10. Revision Status Revision: 1 Date: 23th November 2019 Remark: Second edition Healy GmbH Schloss Krnzlin, Darritzer Str. 6 16818 Krnzlin - Germany 23 | EN EN | 24 Healy GmbH | Schloss Krnzlin | Darritzer Str. 6 16818 Krnzlin Germany T. +49 30 54905949-1 www.healyworld.net | info@healy.de

Label Artwork and Location Model: 0007 Label:

Size: L*W=9*3.4mm Location

Healy GmbH 2019-12-11 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Authority to Act as Agent On our behalf, I appoint Shenzhen Tongce Testing Lab. / 1B/F., Building 1, Yibaolai Industrial Park, Qiaotou, Fuyong, Baoan District, Shenzhen, Guangdong, China (Name of Agent company name and address) to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commissions regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, still resides with Healy GmbH / Schloss Kraenzlin, Darritzer Strasse 6, Kraenzlin, 16818, Germany (Applicant Name and address)

<Signature>

Name: Babak Jafarian Title: CEO Applicant Company: Healy GmbH

Healy GmbH 2019-12-11 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2AVB7-0007 Product Name: Healy Watch Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential:

Schematics Block diagram Operation description BOM These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors.

<Signature>

Name: Babak Jafarian Title: CEO Company: Healy GmbH