Remote Controlled Products This manual includes operating instructions for a variety of remote controlled products. All products work on the same principle and use the same channel setting information. Please read all instructional information and note any specific information pertaining to your particular product. This manual applies to the following products:
6-Button Remote Control Indoor Plug-In Receiver PAR Light Receiver Indoor/Outdoor Screw-In Light Receiver Remote Motion Sensor Products are UL/cUL and/or FCC/IC tested Operational range of up to 100 feet. FEATURES and approved. Note: To independently operate a second re-
ceiver unit using a single remote control, make sure the 4th dip switch on each receiver is set to different settings. Channel 1 - Slide dip switch 4 to the ON position on each receiver to be operated by these buttons. Channel 2 - Slide dip switch 4 to the OFF position on each receiver to be operated by these buttons. 1. 6-BUTTON REMOTE CONTROL Install alkaline 12-Volt remote battery (A23 type). Remove cover from back of transmit-
ter. Using outline of battery chamber as a guide, align battery with chamber and insert battery. Slide cover onto transmitter. Note: One remote control is able to independently operate two receiver units set on the same channel. If more than two receiver units, operating indepen-
dently, are desired, additional remote controls will need to be purchased. D R AFT C O P Y 2. Remote Control Functions. The three but-
tons on the left side of the remote will oper-
ate one or more receiver units with matching addresses. The three buttons on the right side of the remote will operate a second set of one or more receiver units. Channel 1/2 ON: Turns on any receiver unit set to the same channel as this remote control. Battery Chamber
(Type A23) Rear View of Remote Control Function Controls Channel 1 OFF Channel 1 DIM Battery Cover Channel 1 ON 1 2 3 4 ON The remote control includes an optional car visor clip for added convenience that may be installed. 1. To attach car visor clip to remote control (if desired) push it into slot on rear of remote unit until it snaps into place. 2. To remove car visor clip, insert a small, flat-
head screwdriver into slot on back of remote. Gently push down on portion of visor clip inside slot with screwdriver while pulling clip out of remote from top. Optional Car Visor Clip (Included) Channel 2 OFF Channel 2 DIM Channel 2 ON Channel 1/2 OFF: Turns off any receiver unit set to the same channel as this remote control. Channel 1/2 DIM: Activates the DIM feature for any receiver unit set to the same channel as this remote control. Flat-Head Screwdriver Optional Visor Clip Removing Visor Clip - Rear View 2002 DESA International 598-1116-00 RECEIVER INFORMATION All receivers have the following features and ratings:
Rated for 120VAC/60Hz supply voltage. Light can be dimmed when used with remote control (OFF, Low, Med, Hi, Full On). Remembers last selected dim setting. Not for use with Compact Fluorescent bulbs. INDOOR PLUG-IN Turn power off at the fuse or circuit breaker. 1. Remove the existing light fixture. 2. Install the mounting strap as shown using two screws that fit your junction box. Note: The plastic hanger can be used to hold the fixture while wiring. Thread the small end of the plastic hanger through the hole in the center of the cover plate. Insert the small end into one of the slots on the mounting strap. 3. Route the wires from the light receiver 4. Twist the junction box wires and fixture wires together as shown. Secure with UL approved wire connectors. 5. Align the cover plate and cover plate gas-
6. Push the rubber plug firmly into place. 7. If a wet location junction box was not used, caulk the wall plate mounting surface with silicone weather sealant. 8. Adjust the lamp holders by loosening the lock nuts. Note: Do not rotate the lamp holders more than 180 from the factory setting. Caution: To avoid water damage and elec-
trical shock, keep lamp holders 30 below horizontal. ket. Secure with mounting bolt. through the large gasket holes. Caution: Do not exceed the maximum load limits listed above. 3. Check operation. Either activate remote motion sensor or toggle ON/OFF switches on remote control to check operation. RECEIVER Features and Ratings:
Up to 2.5 Amps resistive load. Up to 300-Watt incandescent load. No wiring required. 1. Plug in indoor receiver. 2. Plug in light you wish to control. 4. Using Remote By-Pass Switch. These re-
ceivers are equipped with a remote by-pass switch. This switch allows the user to select between ON and RECEIVER modes. ON mode allows the plugged in light to be oper-
ated manually. RECEIVER mode allows the light to be operated by remote control or remote motion sensor. D R AFT C O P Y 5. Adjust audio alert volume (if applicable). Some models are equipped with an audible alarm which sounds each time the receiver is activated. The alarm volume is adjusted by the thumbwheel on the side of the re-
ceiver unit. Remote By-Pass Switch Remote By-Pass Switch Control Locations White to White Black to Black Alarm Volume Mounting Speaker Control Strap 9. Screw incandescent bulb up to rated watt-
age into module. When screwing in the lamps, do not overtighten. Caution: Do not exceed the maximum load limits listed above. 10. Check operation. Either activate remote motion sensor or toggle ON/OFF switches on remote control to check operation. Rubber Plug PAR LIGHT RECEIVER Features and Ratings:
Up to 300 Watt incandescent load (up to 150 Watt per lampholder). Minimal wiring required. Gasket Junction box ground wire to green ground screw on fixture. Mounting Bolt Wiring PAR Light Receiver 2 598-1116-00 INDOOR/OUTDOOR SCREW-IN LIGHT RECEIVER Features and Ratings:
Up to 150 Watt incandescent load. No wiring required. 1. Screw module into light socket. 2. Screw incandescent bulb up to rated watt-
1. 2. Installing Remote Sensor Install sensor mounting bracket where mo-
tion detection is desired. Attach sensor mounting bracket to a sturdy object (i.e. tree, post, house, etc.) using two screws provided. Make sure unit has an unob-
structed view. Install remote sensor to mounting bracket. Using a Philips-head screwdriver, loosen the clamp screw on the mounting bracket. Insert swivel ball mount on sensor into mounting bracket socket (Note: You should hear a snap). Aim sensor toward area where detec-
tion is desired. Tighten clamp screw. Nut Clamp Screw age into module. Caution: Do not exceed the maximum load limits listed above. Mounting Screw Mounting Bracket Swivel Ball Mount SENSOR Mounting Bracket Socket REMOTE MOTION Select Night or 24 Hour Mode 3. Check operation. Either activate remote motion sensor or toggle ON/OFF switches on remote control to check operation. Features:
No wiring required. Up to 70 feet sensing range, 180 Coverage. Adjustable sensitivity. Day/Night or Night only operation. Test mode. Uses 2 AA batteries. Wall or eave mount. IMPORTANT: The sensor must be mounted with the bottom cover facing down in order to maintain water tightness. D R AFT C O P Y The RANGE control and ON-TIME control are located on the bottom of the sensor. Using your fingernails or a small, flat-head screwdriver, gen-
tly pry the cover until it opens. 1. Check Operation. Set the ON-TIME control to TEST mode. Walk in front of sensor unit. The LED indicator light located on the bot-
tom of the sensor should flash when motion is detected. 2. Adjust Sensor. Turn the RANGE control to the mid position and ON-TIME control to the TEST position. Walk through coverage area noting where you are when the LED begins to flash. Loosen the clamp screw and move the sensor to change the coverage area. Tighten clamp screw when finished. Do not overtighten clamp screw. Check Operation and Adjustment This sensor is able to detect motion day and night or night only. To set the detection mode, remove rear panel by sliding the panel down. Remove batteries if necessary. Slide the DETECT switch to either the DAY/NIGHT or NIGHT ONLY posi-
tion. Replace rear panel by reversing the above instructions. Before mounting sensor, remove rear panel by sliding the panel down. Install 2 AA batteries according to polarity markings inside the battery compartment. Replace rear panel by reversing the above instructions. Installing Batteries Installing Remote Sensor Sensor DAY NIGHT NIGHT ONLY 1 2 3 4 CODES DETECT Detect Control Battery Compartment - Rear View 598-1116-00 3 3. Adjust Range Control. To increase sensitiv-
ity, turn the RANGE control toward MAX. To decrease sensitivity, turn the RANGE con-
trol toward MIN. Note: If the RANGE is set too high, false triggering may result in some environments. CHANNEL SETTINGS control. ON-TIME Control 4. Set ON-TIME Control. Determine the amount of time you want the connected device to stay on after motion is detected (1 or 5 minutes). Slide the ON-TIME control to the corresponding setting. IMPORTANT: Avoid Aiming Control At:
Objects that change temperature rapidly, such as heating vents and air conditioners. These heat sources could cause false triggering. Areas where pets or traffic may trigger the Nearby large, light colored objects reflecting light may trigger the shut-off feature. Do not point other lights at the sensor. MIN MAX RANGE 5 1 TEST LED ON-TIME
(MINUTES) Control Indicator Sensitivity Note: Most installations will not require you to change any of the dip switches on your wireless product or remote control. Note: If purchasing more than one remote control system, select different operating channels unless interaction is desired be-
tween the systems. These remote control products communicate by using channels that can be changed by sliding dip switches into the ON or OFF [on some switches the numbers 1 (ON) and/or 0 (OFF) are used] position on both the transmitter and re-
ceiver unit(s). The channel is factory set; how-
ever, there are 3 switches (8 selectable chan-
nels) that allow you to expand your system and prevent outside interference. Other remote con-
trolled unit(s) may cause interference and the system may not function properly. Follow the instructions below for setting a new channel. 1. Open the cases and locate dip switches on 2. Dip switches 1 through 3 are used for setting the channel (Remote Control Only - position 4 is not used and should remain in OFF position). D R AFT C O P Y 3. To change the channel, slide dip switches to ON or OFF as needed. It is recommended to only change one dip switch at a time and then check to see if system is functioning properly. IMPORTANT: Dip switches in positions 1 through 3 must be in the exact same con-
figuration on both the transmitter and re-
ceiver unit(s) for this system to function properly. both the transmitter and receiver unit(s). Motion Sensor Sensitivity Dip Switches - Shown in the OFF Position (Factory Coverage Area Coverage Angle Most Sensitive 70 ft.
(21 m) 1 2 3 4 Maximum Default) Sensor Motion ON 180 The detector is most sensitive to motion across its field of view. Motion Sensor Least Sensitive Remote Sensor Controls - Bottom View Maximum Range 8 ft.
(2.4 m) Dip Switches Aim Sensor Down for Short Coverage Aim Sensor Higher for Long Coverage Adjusting Motion Sensor Coverage 4 598-1116-00 DIP SWITCH LOCATIONS Dip Switches ON 1 2 3 4 Battery Cover 6-Button Remote Control Screw Cover 1 2 3 4 Dip Switches ON 1 2 3 4 DAY NIGHT DETECT NIGHT ONLY 1 2 3 4 CODES Dip Switches Dip Switches Dip Switches Remote Motion Sensor Indoor Plug-In Receiver Indoor/Outdoor Screw-In Light Receiver D R AFT C O P Y POSSIBLE CAUSE 1. Circuit breaker or fuse is turned off. 2. Switch on device is turned off. 3. Device is defective. Try remote using different device. 4. Signals from transmitter are being blocked, or transmitter is out of range. Check for metal objects that could block the signal, or reposition the transmitter. 5. Weak battery in the transmitter. 6. Dip switches on remote control and wireless unit(s) do not match. 1. Same as 4, 5, and 6 above. TROUBLESHOOTING GUIDE 1. Short term power line failure. 2. Another transmitter on the same channel. PAR Light Receiver SYMPTOM Device does not come on. Device does not turn off. Device comes on ran-
domly. 598-1116-00 5 TECHNICAL SERVICE
(Do Not Send Products) If you experience a problem, follow this guide. You may also want to visit our Web site at:
www.desatech.com. If the problem persists, call* for assistance at 1-800-858-8501, 7:30 AM to 4:30 PM Central Time weekdays. You may also write* to:
DESA International, Inc. P.O. Box 90004, Bowling Green, KY 42102-9004
* If contacting Technical Service, please have the following information available: Model Number, Date of Purchase, and Place of Purchase. REGULATORY INFORMATION NO SERVICE PARTS AVAILABLE FOR THESE PRODUCTS YOUR HEATH/ZENITH TWO YEAR LIMITED WARRANTY This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The user is cautioned that changes or modifications not expressly approved by the party responsible for regulatory compliance could void the users authority to operate the equipment. D R AFT C O P Y This is a "Limited Warranty" which gives you specific legal rights. You may also have other rights which vary from state to state or province to province. For a period of two years from the date of purchase, any malfunction caused by factory defective parts or workmanship will be corrected at no charge to you. Light bulbs and Batteries not covered. To obtain a refund or a replacement, return the product to the place of purchase. Not Covered - Repair service, adjustment and calibration due to misuse, abuse or negligence, light bulbs and other expendable items are not covered by this warranty. Unauthorized service or modification of the product or of any furnished component will void this warranty in its entirety. This warranty does not include reimbursement for inconvenience, installation, setup time, loss of use, or unauthorized service. This warranty covers only Heath/Zenith assembled products and is not extended to other equipment and components that a customer uses in conjunction with our products. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY, REPRESENTATION OR CONDITION OF MERCHANT ABILITY OR THAT THE PRODUCTS ARE FIT FOR ANY PARTICULAR PURPOSE OR USE, AND SPECIFICALLY IN LIEU OF ALL SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUSTOMER AND THERE SHALL BE NO LIABILITY ON THE PART OF DESA FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO ANY LOSS OF BUSINESS OR PROFITS, WHETHER OR NOT FORESEEABLE. Some states or provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Retain receipt for warranty claims. Heath/Zenith reserves the right to discontinue products and to change specifications at any time without incurring any obligation to incorporate new features in products previously sold. 6 598-1116-00