Users Manual MM/MC series CONTENTS 1. Safety Instructions.....4 2. Regulatory Information.....5 3. Precautions.....6 4. Before setting up.......7 5. Features & checking the products......8 Features of Products...8 Checking the products.8 6 Setting up the LCD Monitor.......9 Features of Connectors.....9 Description of Connectors.....9 Connecting the LCD Monitor...10 Warm-up Time....10 7. Adjusting of OSD Menu....11 Features of OSD Controls....11 Description of Control ports..11 OSD Operation...12 8.Adjusting the Viewing angle..13 9.Appendix......14 DVI-D connector Pin Description.....14 Power Saving Mode...14 Specification....15 Trouble shooting.....18 Contact.....18 Safety Instructions Symbol Explanation RISK OF ELCTRIC SHOCK DO NOT OPEN CAUTION !
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER(OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL MEDICAL EQUIPMENT 13XX E246477 WITH RESPECT TO ELECTRIC SHOCK.FIRE AND MECHANICAL HAZARDS ONLY IN ACCORDANCE WITH UL60601-1, AND CAN/CSA C22.2 NO. 601.1 MEDICAL EQUIPMENT CERTIFIED FOR CANADA Grounding Reliability can only be achieved when the equipment is connected to an equivalent receptacle with marked Hospital Only or Hospital Grade Explanation of Graphical Symbols Attention, consult ACCOMPANYING DOCUMENTS The lightning flash with arrowhead symbol, within an equilateral triangle ,is intended to alert the be user to the presence of un-insulated dangerous voltage within the products enclosure that of may sufficient magnitude to constitute a risk of electric shock to persons Stand-by Switch. Press to turn the monitor on or off(Stand-by mode). Alternating Current Regulatory Information FCC RF INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television receptions, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-. Reorient or relocate the receiving antenna.
-. Increase the separation between the equipment receiver.
-. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-. Consult the or an experienced radio /TV technician for help. CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. CE MARKING DECLARATION OF CONFORMITY This LCD Monitor complies with the requirements of the EC Directive 89/336/EECEMC Directive and 93/42/EEC - Medical Device directive The electro-magnetic susceptibility has been chosen at a level that gives correct operation in residential areas. Business and light industrial premises and small-scale enterprises, inside as well as outside of the buildings. All places of operation are characterized by connection to the public low voltage power supply system. Classification:
- Protection against electric shock: Class I
- Applied Parts No Applied Parts.
- Protection against harmful ingress of water: ordinary IPX0
- Mode of operation: Continuous
- Degree of safety in the presence of flammable anesthetics mixture with air or with oxygen or with nitrous oxide
- Not suitable for use in the presence of a flammable anesthetics mixture with air or with oxygen or with nitrous oxide. Precautions Plug the power cord into a properly grounded outlet. There is the risk of electric shock. If you hear a noise or smell smoke from the view box or power cord, unplug the power cord immediately, and call service center. There is the risk of electric shock or fire Do not overload an electrical outlet with too many devices. There is the risk of fire Do not unplug from the outlet by pulling the power cord or when your hands are wet. Do not bend the power cord excessively or place heavy objects on it. Keep children and pets away from the power cord as they may cause damage the power cord. Do not use a damaged power cord or plug. Make sure the plug fits snugly into the outlet. Unplug the Power cord for isolation from supply if you use not monitor for a long time.. Do not expose this monitor to the direct sun-light. Do not allow any object or liquid to enter inside this monitor. There is the risk of electric shock, fire, or damage to the monitor Do not attempt to disassemble, unfix or modify the monitor. Keep the monitor away from high temperature, humidity and dust etc..
-> Operating environment Temperature : 10~40 degrees Celsius () Humidity : 10~80 relative humidity (%) Use a proper voltage/current level indicated. The device could be send back to the manufacturer for recycling or proper disposal after their useful lives. Alternatively the device shall be disposed in accordance with national laws after their useful lives. Equipment with signal input / signal output connectors should either indicate the connected equipment comply with IEC 60601-1 and / or IEC 60601-1-1 harmonized national standard or the combination should be evaluated. This medical monitor is designed for viewing medical X-Ray Images Before setting up Before setting up the LCD monitor, please read this manual to help your understanding of the Monochrome TFT-LCD Monitor. Install the LCD Monitor on a flat place. Dont install in the place with much of water or moisture Put the LCD Monitor in a place with low humidity and a few of dust. Dont overload an electrical outlet with too many devices. There is the risk of fire. Dont expose the LCD monitor to the direct sun light. Keep the monitor away from high temperature. Do not place the monitor in hazardous position. NOTICE Please clean the panel and cabinet of monitor with a clean damp cloth and then wipe and dry with a clean soft cloth Please do not use volatile organic solvents such as alcohol, thinner, and benzenes when cleaning. These can be damaged to the front panel Do not attempt to service, modify or dismantle this product. Recommended service should be done at the prescribed intervals by Heeyoung Service engineer, Agent or a trained Technician. Features & checking the products Features of Waveric series High luminance & High contrast ratio Built-in 11.5-bit LUT Integrated Stable Brightness Control System Built-in Power Supply OSD control for user control Digital Video Interface Ultra Power saving mode Narrow bezel design for space-saving Checking the products The following accessories are included in package. Check to see if they are enclosed with the monitor. If anything is missing or damaged, please contact your local dealer. Monitor Accessory Box TFT-LCD Monitor Power Cord User Manual DVI-D Signal Cable External Photo-sensor(optional) Calibration CD(optional) Graphic Board Box(optional) Graphic Board Install CD Install Manual Setting up the LCD Monitor Feature of Connectors Landscape Portrait Description of Connectors No Name Cable Connections AC Inlet Serial In DVI Connect the plug of AC power cord Use for factory set-up and service purpose Digital Video Interface connection from PC USB(Up stream) Connect the USB cable to PC USB(Down stream) Connect the USB cable to external equipments Setting up the LCD Monitor Connecting the LCD Monitor 1) Connect the DVI-D signal cable to the signal port of the Graphic Card in your computer. 2) Connect the another connector of the DVI-D signal cable on the rear side of the monitor. 3) Connect the power cord to the AC inlet on the rear side of the monitor 4) Try to collect the cable and power cord like the below pictures 5) Turn on the monitor with the power switch of the user control port. AC Power supply PC Graphic Card Warm-up Time All LCD monitors need time to become thermally stable whenever you turn on the monitor After letting the monitor be turned off for a couple of hours. Therefore, to achieve more accurate adjustments for parameters, allow the LCD monitor to be Warmed up for at least 20 minutes before making any screen adjustments. Adjusting of OSD MENU Features of OSD Controls
<Portrait> <Landscape>
LED MENU SELECT + - LOCK Description of Control ports Adjusting of OSD MENU OSD Set the OSD ,menu display position POSITION : Moves the OSD menu to the any direction TIMER : Shows the OSD TIME displays from 5 to 30 sec. PIVOT : Select as a landscape or portrait mode, OSD DATA LEVEL Select the gray scale level 8Bit : Select the 256 gray scale 10Bit : Select the 1021 gray scale SBC SET Support the preset value for luminance LUMI USER, OFF, 350, 400, 450, 500, 550, 600, 650 Select the each value. USER : Value of brightness hot-key control. OFF : SBC function is not operated. 350 ~ 650 : Preset value of luminance. INPUT Support the selection mode for Packed-Pixel and Dual-link signal. PACK Support the Packed-pixel signal graphic card
(Matrox, RealVision) DUAL Support the dual-link signal graphic card (nVidia, ATi) This menu is hidden in OSD MENU This menu can be only selected in Aging mode Entrance of Aging mode :
Press the switch of power & + button for 5~7 sec at the same time. It will be displayed the self-pattern. And then you can select dual mode by OSD menu control. Adjusting of OSD MENU LUMINANCE Select the luminance value of the factory preset . DEF.1 : Support 650cd/m2 with LUT.(MM series model) Notice : * 350cd/m2 (MC20H) *200cd/m2(MC20/MC30) DEF.2 : Support 550cd/m2 with LUT.(MM series model) Notice : * 300cd/m2 (MC20H) *150cd/m2(MC20/MC30) DEF.3 : Support 450cd/m2 with LUT.(MM series model) Notice : * 200cd/m2 (MC20H) *100cd/m2(MC20/MC30) USER : Support the value of range by Hot-keys brightness control. FACTORY Discards the current setting values Reset : Replace to the factory default values INFORMATION Display the information of the monitor status, Model Name, Maximum Resolution, Time of using : Display the used time EXIT Version : Firmware Version Mxxx : Serial number Adjusting the Viewing angle
- For optimal viewing, it is recommended to look at the full face of the monitor and then adjust the monitors height and angle to your own preference. Height ,Tilt ,Swivel
- You are able to adjust the monitors height up to 110mm, angle up to 35degrees right and left, 35 degrees upward
- Adjust the monitors height to the maximum. Rotation(Pivot) Function
- Rotate the panel 90 degree
-> Portrait : Turn clockwise.
->Landscape : Turn counter clockwise. NOTE
- Do not touch the LCD screen when you change the height or the angle.
- It may cause damage or break the LCD screen.
- Careful attention is required not to catch your fingers or hands when you change the height or the angle
<Height> <Tilt>
<Rotate> <Swivel>
Appendix DVI-D Connector Pin Description Pin Signal 1 2 3 4 5 6 7 8 C1 C4 T.M.D.S.Data2-
T.M.D.S.Data2+
T.M.D.S.Data2/4 Shield T.M.D.S.Data4-
T.M.D.S.Data4+
DDC Clock DDC Data N.C N.C N.C Pin 9 10 11 12 13 14 15 16 C2 C5 Signal T.M.D.S.Data1-
T.M.D.S.Data1+
T.M.D.S.Data1/3 Shield T.M.D.S.Data3-
T.M.D.S.Data3+
+5V Power Ground Monitor sense N.C N.C Pin 17 18 19 20 21 22 23 24 C3 Signal T.M.D.S.Data0-
T.M.D.S.Data0+
T.M.D.S.Data0/5 Shield T.M.D.S.Data5-
T.M.D.S.Data5+
T.M.D.S. Clock Shield T.M.D.S. Clock+
T.M.D.S. Clock-
N.C Power-Saving Mode This monitor complies with the DVI-DMPM. Mode LED Indicator Power Dissipation Normal Operation Power Saving Mode Off Mode Green Amber Off Normal consumption Less than 2W Less than 2W Appendix Specification of MM-series ITEM Size Type MM50 MM20 20.1"
21.3 21.3"
a-Si TFT active matrix a-Si TFT active matrix a-Si TFT active matrix Manufacturer NEC IDTECH NEC PANEL Display size 399(H)x319(V)mm 423(H)x337(V)mm 432(H)x324(V)mm Brightness 850cd/m2 1,000cd/m2 1200cd/m2 Viewing Angle 170(H),170(V) 170(H),170(V) 170(H),170(V) Pixel Pitch 0.156mm x 0.156mm 0.165mm x 0.165mm 0.270mm x 0.270mm Contrast Ratio 600:1 600:1 700:1 Resolution Landscape 2560 x 2048 2560 x 2048 1600 x 1200 Portrait 2048 x 2560 2048 x 2560 1200 x 1600 Gradation Packed Type Display Dual-link Digital Interface USB Port 11.5bit LUT 10 bit LUT DVI-D Connector 1Up stream ,2Down Stream User Control Plug & Play Method OSD Control Button Function Power, Menu, Select +, - , Lock AC Input 100-240Vac,50/60Hz VESA DDC2B Power Consumption 75W 80W 70W Saving Mode Less than 2W Regulation Emission Safety FCC class B,CE,FDA510(k) cUL(UL2601-1,CSA C22.22) CE(EN60601-1),MDD Vesa Wall/Arm Mounting VESA-standard ,100 x 100 mm Mechanical Function Height/Tilt/Pivot/Swivel Dimension(mm) Net 438 x458 x 236 476 x 523 x 236 472 x 495 x 236
(W x H x D) Packed 610 x 535 x 350 Optional Item Calibration Photo-sensor, Calibration software Enviromental Operating Storage Temperature :10 to 40 Humidity : 10% to 80%
Temperature: -15 to 60 Humidity: 5% to 90%
Appendix Specification of MM-series ITEM Size Type 21.3"
MM30 20.8 a-Si TFT active matrix a-Si TFT active matrix Manufacturer NEC IDTECH Display size 433(H)x324(V)mm 423(H)x318(V)mm Brightness 1000cd/m2 Viewing Angle 170(H),170(V) 1000cd/m2 170(H),170(V) Pixel Pitch 0.2115mm x 0.2115mm 0.207mm x 0.207mm PANEL Contrast Ratio 700:1 Resolution Landscape 2048 x 1536 Portrait 1536 x 2048 900:1 2048 x 1536 1536 x 2048 Gradation Packed Type Display Dual-link 11.5bit LUT 10 bit LUT Digital Interface Calibration Sensor USB Port DVI-D Connector Built-in Front sensor 1Up stream ,2Down Stream User Control Plug & Play Method OSD Control Button Function Power, Menu, Select +, - , Lock AC Input 100-240Vac,50/60Hz VESA DDC-CI Power Consumption 75W 80W Saving Mode Less than 2W Regulation Emission Safety FCC class B,CE,FDA510(k) cUL(UL2601-1,CSA C22.22) CE(EN60601-1),MDD VESA Wall/Arm Mounting VESA-standard ,100 x 100 mm Mechanical Function Height/Tilt/Pivot/Swivel Dimension(mm) Net 476 x 523 x 236 473 508 236
(W x H x D) Packed 610 x 535 x 350 Environmental Operating Storage Temperature :10 to 40 Humidity : 10% to 80%
Temperature: -15 to 60 Humidity: 5% to 90%
Appendix Specification of MC-series ITEM Size Type MC30 MC20 MC20H 20.8 21.3"
21.3"
a-Si TFT active matrix a-Si TFT active matrix a-Si TFT active matrix Manufacturer IDTECH NEC NEC PANEL Display size 423(H)x318(V)mm 433(H)x324(V)mm 432(H)x324(V)mm Brightness 400cd/m2 250cd/m2 450cd/m2 Viewing Angle 170(H),170(V) 170(H),170(V) 170(H),170(V) Pixel Pitch 0.207mm x 0.207mm 0.270mm x 0.270mm 0.270mm x 0.270mm Contrast Ratio 450:1 450:1 450:1 Resolution Landscape 2048 x 1536 1600 x 1200 1600 x 1200 Portrait 1536 x 2048 1200 x 1600 1200 x 1600 Gradation Display 10bit(1021)grayscale from 3061 Pallet(11.5bit) Digital Interface DVI-D Connector Serial Port USB Port User Control RS-232C 1Up stream ,2Down Stream Method OSD Control Button Function Power, Menu, Select +, - , Lock Plug & Play VESA DDC2B AC Input 100-240Vac,50/60Hz Power Consumption 75W 60W 70W Saving Mode Less than 2W Emission FCC class B,CE Regulation Safety cUL(UL60601-1,CSA C22.2) CE(EN60601-1) CB(IEC60601-1) Vesa Wall/Arm Mounting VESA-standard ,100 x 100 mm Mechanical Function Height/Tilt/Pivot/Swivel Dimension(mm) Net 473 508 x 236 476 x 523 x 236 476 x 523 x 236
(W x H x D) Packed 610 x 535 x 350 Optional Item Calibration Photo-sensor, Calibration software Enviromental Operating Storage Temperature :10 to 40 Humidity : 10% to 80%
Temperature: -15 to 60 Humidity: 5% to 90%
Appendix Trouble Shooting What you see Suggested Actions Screen is blank and Make sure that the power cord is firmly connected and the LCD power indicator is off monitor is on. No signal message Make sure that the signal cable is firmly connected to computer Make sure that the computer is turned on The display image is too Adjust the brightness dark or too light Screen is blank and The monitor is using its power saving system.(DMPM) power indicator light is Move the computers mouse or press a key on the keyboard. steady red or blinks Contact HEEYOUNG Co., Ltd. 1048-8, SHINGIL-DONG DANWON-GU ANSAN-CITY KYUNGGI-DO, 425-839 KOREA Tel : 82-31-491-5506, Fax : 82-31-491-5509 P/N : 97M9500103