I E D U G T R A T S K C U Q I In The Box Get To Know Your Tablet Navigation Mode 13 Pro 2 1 3 3 4 6 5 Turn on your tablet The navigation mode on your tablet allows you to choose between Gesture navigation and 3-Button navigation. Press and hold the Power button for a few seconds until the tablet turns on. Gesture navigation 13 Tablet Folio Case USB-C 3.2 Cable I E D U G T R A T S K C U Q I 13 Pro 36018343_EN_11242025 36018343_EN_11242025 Quick Start Guide Stylue Memory Card Ejection Pin 1 4 7 Power button Memory Card Slot USB-C 3.2 Por Volume Control Camera(Front) Speakers Microphone Light Sensor Camera(Rear) To learn more about your tablet, go to Settings > About Tablet > Get to Know Your Tablet for detailed information. Turn off your tablet Press the Power button and Volume+ button at the same time to turn off your tablet. Volume+ button Power button Swipe up to go home Swipe up and hold for recent apps Swipe from the edges to go back 3-Button navigation 1 2 3 1 2 3 1 Back button 2 Home button 3 Recent apps button To select the mode that best fits your preferences, go to Settings >
System > Gestures > Navigation mode. Factory Reset Stylus Reading Mode Quick Wake & AI Assistance WE CAN HELP 1-888-516-2630 7 DAYS/WEEK 7 a.m. 9 p.m. CST Find more at SCAN HERE FOR MORE PRODUCT INFORMATION AND LEAVE US A REVIEW!
Factory reset To erase all data from your tablet, you can reset your tablet to factory settings. Please back up important data before performing the factory reset. To perform a factory reset, follow the below steps:
1. From the Home screen, swipe up to access App tray and tap Settings . 2. Tap System > Reset options > Erase all data (factory reset) . 3. Enter your PIN (if previously set). 4. Tap Erase all data again to confirm. 5. Your tablet will start the reset process. If your device is not responding and you want to perform a force shutdown, simply press and hold the Power button and the Volume
+ button at the same time for about 8 seconds. Your tablet supports the USI 2.0 stylus for improved writing, drawing, and navigation. To connect, simply place the stylus near the tablet, and it will automatically connect for use. Reading mode optimizes the screen display to enhance the reading experience and reduce eye strain during prolonged use. To enable Reading mode and choose desired effect, go to Settings > Display >
Reading mode. Single tap to wake Single tap to wake lets you easily activate your tablets screen with a tap, allowing quick access without pressing the Power button. Write in text fields Use a stylus to write directly in any text field, converting handwriting into editable text for easy modification. Reading mode Enable Reading mode Chromatic effect Grayscale effect Auto (set effect according to app) To enable this function, go to Settings > Display > Single tap to wake . Google Gemini Google Gemini is your AI assistant that enhances interactions and aids in writing, learning, and creativity. To access Gemini app, press and hold the Power button. To enable Write in text fields or adjust related settings, go to Settings >
Keyboard > On-screen keyboard > Gboard > Write in text fields. Chromatic effect:Enhances colors for better vibrancy and contrast. Grayscale effect:Converts the display to grayscale, minimizing Note: If the stylus is not responding, ensure it is charged and properly connected to your device. Restart your device if you experience connectivity issues. distractions and improving text clarity. Auto:Automatically applies specified reading effects for each app, personalizing the reading experience. Note: Check responses. Setup required. Compatibility and availability varies. Google and Gemini are trademarks of Google LLC. Force shutdown Hello Hello Extend Display Mode Voice assistant & Facial Recognition Other Useful Features Troubleshooting Safety Instructions Expansion mode is to horizontally expand the desktop of a computer to multiple displays, each displaying different content, forming a wider workspace. Extend Display Mode Switch to activate the Extend Display Mode?
Cancel Default Full Screen 1. Connect the tablet with source device using the inbox cable or USB 3.2 and up version cable 2. Click the Default or full screen button 3. Source device confirm the output Voice assistant Voice assistant function, which can be set after logging in to Google account, And it needs to be clear the screen must be on in order to use your voice. if the screen is off, voice assistant will not work. To enable this function, go to Settings > Google > All Services > Search, Assistant&Voice > Google Assistant > Voice Match. Facial recognition Facial recognition, Before you can enable the facial recognition feature, you must first set up a screen lock method. Choose a screen lock Choose your backup screen lock method Pattern.Facial PIN.Facial Password.Facial To enable this function, go to Settings > Security &Privacy > Device Unlock > Face Unlock. Problem Cannot turn my device on. My tablet does not charge. My tablet cannot connect to Wi-Fi. My tablet runs slow. My tablets system is abnormal. Solution/Prevention Press and hold the Power button for more than 3 seconds. Charge the tablet for 10-15 minutes. Use your charger and USB cable to charge the tablet. Check that the power outlet is working and that the charger is properly plugged into the outlet. Reconnect the charger to the device and let it charge for 10-15 minutes. Then press the Power button to check if there is a charging prompt. Get the tablet close to the router, if it doesnt fix Close or uninstall unwanted applications. Restore factory settings. Refer to the electrical and safety information on the tablet before installing or operating the appliance. Do not install near any heat sources such as radiators, heat regulators, stoves or other equipment (including amplifiers) that generate heat. Use only accessories specified or provided by the manufacturer (e.g., dedicated power adapters, batteries, etc.). Replacing with an incorrect battery type may compromise safety measures. The specification of the charger is 9.0V(DC), 2.2A. We recommend that you use this specification to charge the tablet, the USB(C) port of the tablet supports 5.0V(DC), 1.1A output. The power plug should be kept in a state that can be disconnected at any time to avoid emergencies. The device should not be exposed to dripping or splashing water. Use the device at an ambient temperature between 0 and 35 C (32 o 95 F) and at an altitude of no more than 2000 m (air pressure not less than 80kPa). Store or transport the device at ambient temperatures between -20 and 50 C (-4 to 122F). Low or high temperature conditions may cause the device to change its behavior to regulate its temperature. We want you to have a safe and enjoyable experience. Please read the following instructions and precautions before using the tablet. Warning: This product may contain a chemical known to the State of Safety Instructions Safety Instructions Compliance Information California to cause cancer, birth defects, or other reproductive harm. Avoid using the tablet in extremely hot, cold, dusty, and humid environments. The tablet is not moisture-proof/waterproof. Avoid using tablets around water sources. Avoid dropping or forcibly placing the tablet on a hard surface. This may damage the screen or internal electronics and void the warranty. Do not use alcohol, thinner, or benzene to clean the tablet surface. Use only cleaning products that are designed for computer tablet devices. Do not use the tablet while walking or driving. To prevent possible hearing damage, do not listen at high volumes for long periods of time. When you are exposed to high sound pressure, a warning will be displayed on the device. The images in this guide may differ slightly from the actual product. Charge the tablet battery under any of the following circumstances:
1. The battery level icon indicates low power, by showing a drained, red battery icon. 2. The tablet powers-off automatically, and continues to do so even after restarting. 3. On-screen keys do not work. Do not suddenly disconnect the tablet when formatting, uploading or downloading data. This can lead to program errors (e.g., system or screen freezing). Electrostatic discharge is normal and can occur in electronic devices, and although it is not life-threatening, it can damage files or damage memory and its contents. Disposing of the battery in a fire or hot oven, or mechanically crushing or cutting the battery, may result in an explosion. Leaving the battery in extremely hot surroundings, such as sunlight, fire, or hot surfaces, may result in an explosion or leakage of flamma-
ble liquid or gas. Batteries subjected to extremely low air pressure may cause an explosion or leakage of flammable liquid or gas, risk of fire or explosion if the battery is replaced by an incorrect type!
Disassembling the tablet will void the manufacturers warranty. Tablet functionality, hardware, software, and warranty information may be improved or modified by the manufacturer or their respective owners and are subject to change without notice. From the Home screen, swipe up to access App tray and tap Settings >
About Tablet > Regulatory labels to view the cetification information. Applicable products have the FCC logo on the product label and/or an FCC ID in the format FCC ID: 2AYT536018343. Google, Android, Google Play, and other marks are trademarks of Google LLC. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interfer-
ence in a residential installtion. This equipment generates uses and radiates radio frequency energy and may cause harmful interference to radio communications if not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or position the receiving antenna. Increase the distance between the device and the receiver. Connect the device to an outlet on a circuit different from the one to which the receiver is connected. Consult your dealer or an experienced radio/TV technician for assistance. WARNING: Changes or modifications to this product not expressly approved by the party responsible for compliance could void the usert authority to operate the equipment. Shielded cables must be used with this unit to ensure compliance with the Class B FCC limits. operation must meet the following two conditions: (1) This Manufactured under license from DTS, Inc. and/or its affiliates. For patents, see https://xperi.com/dts-patents/. DTS, the DTS logo, DTS:X, the DTS:X logo, and DTS:X Ultra are trademarks or registered trademarks of DTS, Inc. and/or its affiliates in the U.S. and/or other countries. DTS, Inc. and/or its affiliates. All rights reserved. The FCCs SAR limit is 1.6 W/kg, with a maximum SAR value of 1.234 W/
kg when testing the device for use on the body. The device was tested at 0 mm and meets RF exposure requirements.
