FCC ID: 2AAR8T130 Wireless Voice Transmission Device

User manual of wireless tour guide Microphone Transmitter: T130 1On-off operation Turn onKeep pressing theM" button for 2 seconds to turn on. Turn offKeep pressing the M button for 2 seconds to turn off. 2The person in charge of the devices needs to know how to set the ID ID can also be understood as channel ):

(1) Why and when need to set the ID:

1, When there are two or more groups using the devices at the same location,to avoid the interference between the groups,you need to set different IDs for the devices (including both transmitters and receivers) of different groups. 2,When you need to add more receivers to a group,and the ID of these added receivers is not the same as that of the devices of the group,you need to set the ID of these added receivers to be the same as that of the group.(The ID of the transmitter and the receivers in a group must be the same.)

(2) The ways of ID setting:

We have two ways to do this: Wireless ID setting and manual ID setting.(We will use wireless ID setting if we have to set the ID for many receivers;And we will use manual ID setting if we have to set the ID for only a few receivers.) 1 Wireless ID setting:

The ID setting of transmitter: Turn off the transmitter,insert the microphone,keep pressing the "

" button by your right hand, and then press the " M " button for 2 seconds by your left hand to turn on the transmitter,and the right hand leaves the button when you see the ID number is changing.Now you have entered the ID setting mode,you can then click the "

" or "

" button to change the ID number,and then click the "M" button to confirm it,now it has entered the wireless transmitting status of ID matching.(Now the ID number is flashing,and it shows the antenna "

" icon and the power status icon).Now we can put the transmitter aside and continue to do the wireless ID setting of the receivers:

The wireless ID setting of receivers: Turn off the receiver,insert the

" button by your left hand ,and then earphone,keep pressing the "

press the "

" button for 2 seconds by your right hand to turn on the receiver,and the left hand leaves the button when the ID number shows

"00",now the receiver has entered the wireless ID receiving mode,and its ID number will change to the same one as that of the transmitter's .(This step must be done under the condition that the transmitter is at the wireless transmitting status of ID matching: The ID number of the transmitter is flashing) After the ID numbers for the transmitter and all the receivers for the same group are set to be the same,turn off all of them,the wireless setting process is finished.When you turn them on again,they can work now. 2 Manual ID setting:

The manual ID setting of receivers: Turn off the receiver,keep pressing the "

" button by your right hand, and press the "

" button for 2 seconds by your left hand to turn on the receiver,the right hand leaves the button when the ID number is changing,now the receiver has entered the manual ID setting mode,you can click the "

" button or the "

" button to change the ID number,and then click the "

" button to confirm it.Then turn it off,the manual ID setting process is finished. Receiver: ATG -100R Earphone 1On - off operation Turn onKeep pressing the Turn offKeep pressing the 2Volume adjustment:

button for 2 seconds to turn on. button for 2 seconds to turn off. When the display screen shows the searching icon

, it means it is searching signal at this moment, the volume can not be adjusted. As soon as the receiver receives the transmitting signal,the display screen will show the signal icon ,now you can click the or button to adjust the volume. The volume has 10 levels from 0 to 9. Attention:

When the transmitters and receivers are not used for a long time,please charge them once every 3 months,so that the batteries can be protected. (There is lithium battery inside the device, if it was not used or charged for a long time,the battery would be damaged.) User manual of Charging case 1Power supplyAC 90V--250V 2When it is charging,take the foam out,and keep the cover open . 3Normally it takes about 3 hours to finish the charging. FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AAR8T130 LABEL AND LOCATION Wireless Voice Transmission Device Model No.: T130 FCC ID: 2AAR8T130 Operate voltage: DC 5V (Battery: 3.7V, 900mAh) Size: L2.0cm*W1cm Label And Location This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 1 of 1

Shenzhen Qi Xin Chuang Zhan Technology Co., LTD Rm 928, Bldg A, Fengtian Industrial Park, No.308, Qinhu Xuegang Bei Rd., Longhua District, Shenzhen, China Tel: 13728763865 Fax: 0755-28073262 FCC ID: 2ANVTEX-100T Date: 2020-06-24 Federal Communications Commission 7345 Oakland Mills Road Columbia MD 21046 To Whom It May Concern:

The letter grants authorization of HENAN ESHOW ELECTRONIC COMMERCE CO., LTD to apply the FCC for a change in identification. This authorization applies to Shenzhen Qi Xin Chuang Zhan Technology Co., LTD FCC ID: 2ANVTEX-100T, granted on 03/31/2020, The equipment is electrically identical. We are aware that HENAN ESHOW ELECTRONIC COMMERCE CO., LTD intends to market the above referenced product under 2AAR8T130 . The only change being the FCC ID and the label on the device. The original test results, technical information and relevant documents continue to be representative of and applicable to the change ID equipment. Should there be any question, please feel free to contact us. Sincerely,

(Signed) Name / Title: Yun Zhang / Manager Company: Shenzhen Qi Xin Chuang Zhan Technology Co., LTD Address: Rm 928, Bldg A, Fengtian Industrial Park, No.308, Qinhu Xuegang Bei Rd., Longhua District, Shenzhen, China Phone: 13728763865 Fax: 0755-28073262 E-Mail: 121693461@qq.com

HENAN ESHOW ELECTRONIC COMMERCE CO., LTD Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 To whom it may concern:

06/24/2020 We, HENAN ESHOW ELECTRONIC COMMERCE CO., LTD the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behalf in all matters relating to applications for equipment authorization FCC ID: 2AAR8T130 including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, Phone:

Fax:

E-Mail:

Name:

Company: HENAN ESHOW ELECTRONIC COMMERCE CO., LTD Address:

Weidong Shen Room 722, Sanjiang Building, No.170 Nanyang Road, Huiji District, Zhengzhou, Henan, China 86-371-63262209 86-371-63628071 shenweidong02@126.com

HENAN ESHOW ELECTRONIC COMMERCE CO., LTD Date: 2020-06-24 Federal Communications Commission 7345 Oakland Mills Road Columbia MD 21046 Attention: Application Examiner / Review Engineer Subject: Request for a Change in Identification per Section 2.933 of the FCC Rules FCC ID: 2AAR8T130 To The Commission:

This change in identification request applies for a new FCC ID as established in 47 CFR 2.933(b) for a currently approved device. This application by HENAN ESHOW ELECTRONIC COMMERCE CO., LTD will establish a new FCC ID under 2AAR8T130 for the purpose of marketing. The original grant to Shenzhen Qi Xin Chuang Zhan Technology Co., LTD with FCC ID: 2ANVTEX-100T will remain in effect. Per 2.933(b) 1.) The original identification is: 2ANVTEX-100T 2.) The original granted date is: 03/31/2020 3.) The equipment is electrically identical. 4.) The original test results are applicable and representative of this changed device. 5.) External photographs are included in this application. The following files are electronically submitted as attachments:

FCC ID label and label location External photographs Letter of Change FCC ID Authorization Letter for FCC ID User Manual Product Equality Declaration Sincerely, Weidong Shen Name:

Company: HENAN ESHOW ELECTRONIC COMMERCE CO., LTD Address: Room 722, Sanjiang Building, No.170 Nanyang Road, Huiji District, Zhengzhou, Henan, China 86-371-63262209 86-371-63628071 shenweidong02@126.com Phone:

Fax:

E-Mail:

HENAN ESHOW ELECTRONIC COMMERCE CO., LTD Date: 2020-06-24 To:

Federal Communication Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern, Original FCC ID: 2ANVTEX-100T; Model Number: EX-100T New FCC ID: 2AAR8T130; Model Number: T130 This is to advise and officially, that we, HENAN ESHOW ELECTRONIC COMMERCE CO., LTD, hereby declare that the product names same and only FCC ID and model number difference as market requirement;

The original test results continue to be representative of and applicable to the equipment of the new FCC ID;

If you have any query, please feel free to contact me. Sincerely, Name:

Company:

Address:

Phone:

Fax:

E-Mail:

Weidong Shen HENAN ESHOW ELECTRONIC COMMERCE CO., LTD Room 722, Sanjiang Building, No.170 Nanyang Road, Huiji District, Zhengzhou, Henan, China 86-371-63262209 86-371-63628071 shenweidong02@126.com