FCC ID: 2BC5F-HH-676Y Childrens car remote control

R Henan Honghui Electronic Technology Co., Ltd LED2 LED1 LED3 Forward retreat Right Left speed swing brake Baby carriage remote control product manual 2.4G wireless transmitter remote control Product Type:HH-676Y Product Configuration:

Battery Specification: 1 . 5 V ( AAA) * 2 Section Operating Voltage:DC2.0-3.6V Quiescent DC:0.5uA Modulation Mode:GFSK Transmission frequency:2.400-2.483GHz NO.20,4/F,Building 1,NO36,Hong song road,High-techzone zhengzhou Page 1 R Henan Honghui Electronic Technology Co., Ltd This remote control shares 6 units at 2.419 GHz, 2.425 GHz, 2.445 GHz, 2.450 GHz, 2.470GHz, and 2.474GHz Frequency point. When conducting fixed frequency testing, select high, medium, and low fre-

quency points for testing. Simultaneously press the three buttons "front+left+brake", load the battery and power it on to enter the fixed frequency test mode. By default, enter mode 1 Frequency transmission mode, with a frequency point of 2.474GHz, and LED1 constantly on for prompt. Afterwards, release all buttons and press the "swing" button to switch modes. 1. Press the "swing" button for the first time to switch to mode 2: fixed frequency transmis-

sion mode, with a frequency point of 2.445GHz and LED2 constantly on. 2. Press the "swing" button for the second time to switch to mode 3: fixed frequency transmis-

sion mode, frequency point 2.419GHz, LED1, LED2 Highlight the prompt. 3. Press the "swing" button for the third time to switch to mode 4: fixed frequency reception mode,with a frequency point of 2.474GHz and LED 3 constantly on. 4. Press the "swing" button for the fourth time to switch to mode 5: fixed frequency reception mode, frequency point 2.445GHz, LED1, LED3 Highlight the prompt. 5. Press the "swing" button for the fifth time to switch to mode 6: fixed frequency reception mode, frequency point 2.419GHz, LED2, LED3 Highlight the prompt. 6. Press the "swing" button for the 6th time to switch to mode 7: single carrier mode,fre-

quency 2.474GHz, LED1, LED2, LED3 Always on prompt. 7. Press the "swing" button for the 7th time to switch to mode 8: single carrier mode,fre-

quency 2.445GHz, LED1, LED2, LED3 All off prompt. 8. Press the "swing" button for the 8th time to switch to mode 9: single carrier mode,fre-

quency 2.419GHz, LED1, LED2, LED3 Always on prompt. 9. Press the "swing" button for the 9th time to return to mode 1: fixed frequency transmission mode,with a frequency point of 2.474GHz and LED1 constantly on. 10. Press for the 10th time and return to mode 2, repeating the cycle. FCC STATEMENT :

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. RF warning statement:

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. NO.20,4/F,Building 1,NO36,Hong song road,High-techzone zhengzhou Page 2

Label Location On EUT Label Product Name: Children's car remote control Model No.: HH-676Y FCC ID: 2BC5F-HH-676Y This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation.

- Henan Honghui Electronic Technology Co., Ltd -

Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 U.S. Agent Designation 10/12/23 Henan Honghui Electronic Technology Co., Ltd acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought (FCC ID: 2BC5F-HH-676Y):

Name and company of U.S. agent: Linkwld LLC Physical U.S. address of agent: 1942 Broadway St. STE 314C, Boulder, CO, 80302, US FRN of U.S. agent: 0033625682 Email address of U.S. agent: Timothy.linkwld@proton.me Linkwld LLC acknowledges their obligation to accept service of process on behalf of Henan Honghui Electronic Technology Co., Ltd. Henan Honghui Electronic Technology Co., Ltd with the FRN [0034337014] accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under 2.911(d)(7). Sincerely, Chen Ronghui Signature

[Name] Chen Ronghui

[Title] general manager

[Company] Henan Honghui Electronic Technology Co., Ltd Signature

[Name of U.S. agent] Timothy Zhu

[Title of U.S. agent] Manager

[Company of U.S. agent] Linkwld LLC The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB.

Henan Honghui Electronic Technology Co., Ltd Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 10/12/23 To whom it may concern:

We, [Henan Honghui Electronic Technology Co., Ltd], hereby certify that the equipment for which authorization is sought (FCC ID: [2BC5F-HH-676Y]) is not covered equipment prohibited from receiving an equipment authorization pursuant to 2.903 of the FCC rules. We also certify that, as of the date of the filing of the application, we are not identified on the Covered List (https://www.fcc.gov/supplychain/coveredlist) as an entity producing covered equipment. By signing this form, we confirm the above and that we are aware of the application requirements listed under 2.911(b) and (d)(5) and (6). Sincerely, Chen Ronghui 2 0 V

, U

) i i

d n a

) i

) 5

) d

1 1 9 2 _ u q E d e r e v o C

l e d o m

_ 2 6 Signature

[Ronghui Chen]

[general manager]

[Henan Honghui Electronic Technology Co., Ltd]

The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01.