Aruba 580 Series Outdoor Access Points Installation Guide The Aruba 580 Series outdoor wireless access points (AP-584, AP-585 and AP-587) support the IEEE 802.11ax standard, delivering high performance with the MIMO (Multiple-Input, Multiple-Output) and OFDMA (Orthogonal Frequency Division Multiple Access) technologies, while also supporting 802.11a/b/g/n/ac wireless services. Package Contents 580 Series access point M20 cable gland x 2 USB Type-C console cable x 1 Ground lug kit x 1 2.4GHz Vpol N-type BLE antenna x 1 (AP-584 only) Tools Required Phillips screwdriver (#2 for M4x6 screw) Flat blade screwdriver (for Ethernet port cap) 8mm Allen or hex key (for USB console cap) The weatherproof caps for Ethernet and Console interfaces are connected to the access point, not loose in the package. Mounting kits for use with the 580 Series access points are sold separately. Contact your Aruba sales representative for details. Inform your supplier if there are any incorrect, missing, or damaged parts. If possible, retain the carton, including the original packing materials. Use these materials to repack and return the unit to the supplier if needed. Rev 01 | November 2021 1 Hardware Overview Figure 1 AP-584 Front View (with Aesthetic Cover) The antenna connectors of the AP-584 are covered by an aesthetic cover. The aesthetic cover can be removed when necessary. If leaving the cover in place, be careful not to exceed the antenna cable bend radius, or use proper angled connector cables to minimize cable bends. Figure 2 AP-584 Rear View (with Aesthetic Cover) USB Console Port, Reset Button and LED 2 Aruba 580 Series Outdoor Access Points | Installation Guide AC Power Port E1/SFP+
E2/PSE E0/PoE+
Grounding Point Figure 3 AP-585 Front View Figure 4 AP-585 Rear View USB Console Port, Reset Button and LED AC Power Port E1/SFP+
E2/PSE E0/PoE+ Grounding Point Aruba 580 Series Outdoor Access Points | Installation Guide 3 Figure 5 AP-587 Front View Figure 6 AP-587 Rear View USB Console Port, Reset Button and LED AC Power Port E1/SFP+
E2/PSE E0/PoE+
Grounding Point External Antenna Connectors The AP-584 access point comes with four external Wi-Fi antenna connectors and one external BLE antenna connector. One 2.4GHz Vpol omni-directional N-type BLE antenna is included in the package of the AP-584 access point. A Wi-Fi antenna is not included in the package and must be purchased separately, refer to the 580 Series ordering guide on the Aruba website https://www.arubanetworks.com. Mounting instructions for the antennas for the AP-584 access points are provided with the antennas. The mounting must be consistent with the instructions provided to ensure compliance with US and Canadian regulatory requirements when used outdoors. 4 Aruba 580 Series Outdoor Access Points | Installation Guide
External antennas for this device must be installed by an Aruba Certified Mobility Professional (ACMP) or other Aruba-certified technician, using manufacturer-approved antennas only. The Equivalent Isotropically Radiated Power (EIRP) levels for all external antenna devices must not exceed the regulatory limit set by the host country/domain. Installers are required to record the antenna gain for this device in the system management software. Les antennes externes pour cet appareil doivent tre installes par un professionnel de la mobilit certifi Aruba
(ACMP) ou un autre technicien certifi Aruba, en utilisant uniquement des antennes approuves par le fabricant. Les niveaux quivalents de puissance rayonnement isotrope (EIRP) pour tous les priphriques d'antenne externe ne doivent pas dpasser la limite rglementaire dfinie par le pays hte / domaine. Les installateurs doivent enregistrer le gain d'antenne pour cet appareil dans le logiciel de gestion du systme. Figure 7 AP-584 Bottom View (without Aesthetic Cover) WI-FI 3 WI-FI 2 BLE WI-FI 0 WI-FI 1 LED The 580 Series access point is equipped with one LED that indicates the system status of the access point. Aruba 580 Series Outdoor Access Points | Installation Guide 5 Table 1 580 Series LED Meanings during Boot Up LED Color/State Meaning System LED Off Red No power to AP Initial power-up Flashing - Green AP booting, not ready On - Green AP ready. GbE (or better) or SFP+ connected. The LED turns off after 1200 seconds Green - Yellow, 6 seconds period AP ready. 100Mb connected. The LED turns off after 1200 seconds Green - Flashing1 AP in deep sleep Red - Flashing2 AP in thermal shutdown 1. Mostly off (off 6 seconds, then one blink flash) 2. Equally off/on (off 1 second, then red 1 second) Table 2 580 Series LED Meanings during Operation LED Color/State Meaning System LED Solid Red General fault - Immediate attention required One red blink every 3 seconds Radio 0 fault (5 GHz) Two quick red blinks 0.5 seconds apart cycled every 3 seconds Radio 1 fault (2.4GHz) Ethernet Ports The 580 Series access point is equipped with three Ethernet ports:
E0 PoE+ port: 100/1000/2500/5000Base-T auto-sensing MDI/MDI-X wired network port (RJ45). The E0 port supports PoE-in, allowing the AP to draw power from an 802.3at/802.3bt PoE power source. E1 SFP+ port: 10GBASE-R SFP+ port. E2 PSE port: 100/1000Base-T auto-sensing MDI/MDI-X wired network port (RJ45). The AP supports 802.3af PoE-Out when PoE powered, and supports up to 802.3at when powered by AC. To enable 802.3at support on E2, Intelligent Power and Temperature Monitoring (IPTM) must be enabled on the AP to properly monitor and maintain safe operations of the AP under higher power draw requirements. If IPTM is disabled, the maximum PoE support on E2 is 802.3af. AC Power Port The 580 Series access point is equipped with an AC power port. The 580 Series access point does not ship with any AC power cables. Aruba offers an AC power connector kit (sold separately) for customers to assemble their own AC power cable. Grounding Point Always remember to protect the access point by installing the grounding line first before connecting to a network and applying power. Additionally, if removing or taking down the AP, the grounding line should be the last item disconnected. 6 Aruba 580 Series Outdoor Access Points | Installation Guide USB Type-C Console Port Use the included USB Type-C console cable to connect the access point to a laptop or a serial terminal for direct management. Use an 8mm Allen or hex key to open the cover of the USB Console port. Reset Button The reset button can be used to reset the access point to factory default settings or turn off/on the LED display. There are two ways to reset the access point to factory default settings:
Reset the AP during normal operation Press and hold down the reset button using a small, narrow object such as a paper clip for more than 10 seconds during normal operation. Reset the AP while powering up 1. Press and hold down the reset button using a small, narrow object such as a paper clip while the access point is not powered on via PoE. 2. Connect the power supply (PoE) to the access point while the reset button is being held down. 3. Release the reset button on the access point after 15 seconds. To turn off/on the LED display, press and release the reset button using a small, narrow object, such as a paperclip for less than 10 seconds during normal operation of the access point. Before You Begin Refer to the sections below before beginning the installation process.
FCC Statement: Improper termination of access points installed in the United States configured to non-US model controllers will be in violation of the FCC grant of equipment authorization. Any such willful or intentional violation may result in a requirement by the FCC for immediate termination of operation and may be subject to forfeiture (47 CFR 1.80). Pre-Installation Checklist Before installing your access point, be sure that you have the following:
Cat5E or better shielded cable with network access A compatible PoE injector with power cord One of the following network services:
Aruba Discovery Protocol (ADP) DNS server with an A record DHCP Server with vendor specific options Aruba, in compliance with governmental requirements, has designed the 580 Series access points so that only authorized network administrators can change configuration settings. For more information about AP configuration, refer to the AP Software Quick Start Guide.
Access points are radio transmission devices and as such are subject to governmental regulation. Network administrators responsible for the configuration and operation of access points must comply with local broadcast regulations. Specifically, access points must use channel assignments appropriate to the location in which the access point will be used. Aruba 580 Series Outdoor Access Points | Installation Guide 7 Outdoor Planning and Deployment Considerations Prior to deploying an outdoor wireless network, the environment must be evaluated to plan for a successful WLAN deployment. Successfully evaluating the environment enables the proper selection of access points and antennas and assists in the determination of their placement for optimal RF coverage. This process is considered WLAN or RF planning and Arubas system engineers can assist in the outdoor planning process. The rules for the 5600-5650 MHz band vary by region. Identifying Specific Installation Locations Use the access point placement map generated by the Aruba RF Plan software application to determine the proper installation location(s). Each location should be as close as possible to the center of the intended coverage area and should be free from obstructions or obvious sources of interference. These RF absorbers/
reflectors/interference sources will impact RF propagation and should be accounted for during the planning phase and adjusted for in the RF plan.
Use of this equipment in near proximity, either horizontally or vertically, with other equipment should be avoided because it could result in improper operation. If such use is necessary, this equipment and the other equipment should be observed to verify that they are operating normally. Identifying Known RF Absorbers/Reflectors/Interference Sources Identifying known RF absorbers, reflectors, and interference sources while in the field during the installation phase is critical. Make sure that these sources are taken into consideration when you attach an access point to its fixed location. RF absorbers include:
Cement/concreteOld concrete has high levels of water dissipation, which dries out the concrete, allowing for potential RF propagation. New concrete has high levels of water concentration in the concrete, blocking RF signals. Natural ItemsFish tanks, water fountains, ponds, and trees Brick RF reflectors include:
Metal ObjectsMetal pans between floors, rebar, fire doors, air conditioning/heating ducts, mesh windows, blinds, chain link fences (depending on aperture size), refrigerators, racks, shelves, and filing cabinets. Do not place an access point between two air conditioning/heating ducts. Make sure that access points are placed below ducts to avoid RF disturbances. RF interference sources include:
Other Wi-Fi networks Microwave ovens Bluetooth devices Access Point Installation Service to all Aruba products should be performed by trained service personnel only. 8 Aruba 580 Series Outdoor Access Points | Installation Guide Using Mount Kits The 580 Series access point can be installed on a wall or attached to a pole by using mount kits:
Table 3 Applicable Mount Kits for 580 Series Access Point Part Number Description Supported Model R9H97A JW054A JW055A R6W11A AP-OUT-MNT-V1A Aruba Outdoor AP Pole/
Wall Long Mount Kit. AP-584/AP-585: Wall or Pole AP-270-MNT-H1 Aruba Outdoor AP Hanging or Tilt Install Mount Kit. AP-587: Wall or Pole AP-584/AP-585: Flat or Sloped Ceiling AP-270-MNT-H2 Aruba Outdoor AP Access Flush Wall or Ceiling Mount. AP-587: Wall AP-584/AP-585: Flat Ceiling AP-270-MNT-H3 Aruba Outdoor AP Hanging or Dual-Tilt Install Mount Kit. AP-587: Wall or Pole AP-584/AP-585: Flat or Sloped Ceiling The 580 Series access point does not ship with any mount kits. These mount kits are available as accessories and must be ordered separately. For installation instructions on mount kits, please refer to their respective installation guides found on the Aruba support site https://asp.arubanetworks.com.
This 580 Series access point is intended for installation in a RESTRICTED ACCESS LOCATION attached to a pole or installed on a wall. Installers should disconnect power before working with or near the access point. To prevent dropping and damage to the 580 Series access point or to appendages of the handlers, extra care should be taken when handling the access point. Grounding the Access Point Grounding the access point must be completed before powering up the device. The ground wire should be #8 AWG. 1. Strip the insulating jacket off of one end of the ground wire and place the bare conductor into the ground lug
(included in the package), then crimp the connection by pressing firmly with the crimping pliers. 2. Fasten the ground lug to the grounding point on the access point with the screw included in the package. Connecting the Ethernet Cable To connect the Ethernet cable to the access point, perform the following steps using the M20 cable glands that ship with your access point. Failure to use the included cable glands can lead to connectivity and PoE issues. The cable is not included and must be purchased separately. Purchase a suitable UV-resistant, outdoor rated, CAT 5E or better shielded cable for use with the access point. Aruba 580 Series Outdoor Access Points | Installation Guide 9 Figure 8 Ethernet Cable and M20 Cable Gland Assembly Ethernet Cable O-ring Gland Body Seals Clip Sealing Nut 1. Remove the dust cap from the Ethernet port 2. Slide the sealing nut, clip, gland body and O-ring over the cable. 3. Insert the RJ45 connector to the Ethernet port. 4. Place the O-ring on the gland body, and ensure it is in place. 5. Thread the gland body into the Ethernet port and tighten to a torque of 8.9 in/lbs (1.0 Nm). 6. Combine the two split seals over the cable, and push towards the gland body until located at the recess of the gland body. 7. Move the clip towards the gland body, passing over the seals, until the wavy end of the clip properly fits into the wavy end of the gland body. 8. Tighten the sealing nut onto the gland body to a torque of 8.9 in/lbs (1.0 Nm). Two sets of seals are provided in the package for use with the Ethernet cables. One is applicable for cables with 4-6 mm diameter, and the other is applicable for cables with 6-10 mm diameter. 10 Aruba 580 Series Outdoor Access Points | Installation Guide Figure 9 Ethernet Cable and M20 Cable Gland Installed to AP Connecting the Fiber-optic Cable The fiber-optic cable is not included in the package and must be purchased separately. Purchase a suitable 6-
12 mm diameter, UV-resistant, outdoor rated cable for use with the access point. The CKIT-OD-SFP SFP cable gland is not included in the package and must be purchased separately, refer to the 580 Series ordering guide on the Aruba website https://www.arubanetworks.com. Figure 10 Fiber-optic Cable and CKIT-OD-SFP SFP Cable Gland Gland Body Seals Clip Sealing Nut To connect the fiber-optic cable to the access point, perform the following steps. 1. Remove the dust cap from the E1 SFP+ port. Aruba 580 Series Outdoor Access Points | Installation Guide 11 2. Insert the transceiver module into the SFP+ port, and ensure it is in place. 3. Slide the sealing nut, clip, seals and gland body over the fiber-optic cable. 4. Insert the connector of the fiber-optic cable into the transceiver module, and ensure the connector is firmly in place. 5. Thread the gland body into the E1 SFP+ port on the AP and tighten to a torque of 45 in/lbs (5.0 Nm). 6. Combine the two split seals over the cable, and push towards the gland body until located at the recess of the gland body. 7. Move the clip towards the gland body, passing over the seals, until the wavy end of the clip properly fits into the wavy end of the gland body. 8. Tighten the sealing nut onto the gland body to a torque of 36 in/lbs (4.0 Nm). Figure 11 Fiber-optic Cable and CKIT-OD-SFP SFP Cable Gland Installed to AP Connecting the AC Power Cable Best Practice for Outdoor Connection to AC Mains In all circumstances and with any outdoor infrastructure the recommended practice is to connect to AC mains in an outdoor grade weather protected junction box. This needs to be implemented by a qualified resource in a manner that is consistent with the electrical code in force in the jurisdiction of deployment. In many countries this will require a licensed electrician to perform this operation. In Japan, this would be performed by a Certified Electrician by Ministry of Economy, Trade and Industry. The use of plugs with infrastructure equipment is suitable only for temporary installs where nuisance tripping of GFI plugs is considered tolerable. if a plug is desired for attachment to the cable assemblies then the installer is expected to follow all directions provided with the plug end in a fashion consistent with local electrical code.
Translation: Please only use included or Aruba specified cables, power cords, AC power supplies and batteries. The power cord should not be used with other electric equipment than what is specified by Aruba. 12 Aruba 580 Series Outdoor Access Points | Installation Guide Assembling the AC Power Cable The 580 Series access point does not ship with any AC power cables. Aruba offers an AP-AC-MLX outdoor Molex AC connector kit (sold separately) for customers to assemble their own AC power cable. For installation instructions on the AP-AC-MLX kit, refer to the AP-AC-MLX AC Connector Kit Installation Guide shipped with the AP-AC-MLX kit. The required specifications for third party cable used with the AP-AC-MLX outdoor Molex AC connector kit are as follows:
AC power cable specifications: UV-resistant, outdoor-rated three-wire AC cable (18 AWG) with outside cable diameter of 6-12mm and inside wire diameter no more than 3.1mm Connecting the AC Power Cable To connect the AC power cable to the access point, assemble the AC power cable as instructed in the installation guide of the AP-AC-MLX outdoor AC connector kit (sold separately), and then perform the following steps using the M25 cable gland (included in the AP-AC-MLX kit). 1. Remove the weatherproof cap on the AC power port. 2. Slide the sealing nut, clip, gland body and O-ring over the cable. See Figure 12. Figure 12 AC Power Cable and M25 Cable Gland AC Cable O-ring Gland Body Seals Clip Sealing Nut 3. Insert the power cable connector into the AC power port. Aruba 580 Series Outdoor Access Points | Installation Guide 13 Figure 13 Inserting AC Cable Connector into AC Power Port on AP 4. Place the O-ring on the gland body, and ensure it is in place. 5. Thread the gland body into the AC power port and tighten to a torque of 10.6 in/lbs (1.2 Nm). 6. Combine the two split seals over the cable, and push towards the gland body until located at the recess of the gland body. 7. Move the clip towards the gland body, passing over the seals, until the wavy end of the clip properly fits into the wavy end of the gland body. 8. Tighten the sealing nut onto the gland body to a torque of 10.6 in/lbs (1.2 Nm). 14 Aruba 580 Series Outdoor Access Points | Installation Guide Figure 14 AC Power Cable and M25 Cable Gland installed to AP Software For instructions on choosing operating modes and initial software configuration, refer to the AP Software Quick Start Guide.
Aruba access points are classified as radio transmission devices, and are subject to government regulations of the host country. The network administrator(s) is/are responsible for ensuring that configuration and operation of this equipment is in compliance with their countrys regulations. For a complete list of approved channels in your country, refer to the Aruba Downloadable Regulatory Table at https://www.arubanetworks.com/techdocs/DRT/
Default.htm Verifying Post-Installation Connectivity The integrated LEDs on the access point can be used to verify that the access point is receiving power and initializing successfully (see Table 1 and Table 2). Refer to the AP Software Quick Start Guide for further details on verifying post-installation network connectivity. Electrical and Environmental Specifications Electrical Ethernet E0 PoE+ port: 100/1000/2500/5000Base-T auto-sensing MDI/MDI-X wired network port (RJ45). The E0 port supports PoE-in, allowing the AP to draw power from an 802.3at/802.3bt PoE power source. E1 SFP+ port: 10GBASE-R SFP+ port. E2 PSE port: 100/1000Base-T auto-sensing MDI/MDI-X wired network port (RJ45). The AP supports 802.3af PoE-Out when PoE powered, and supports up to 802.3at when powered by AC. Environmental Operating Aruba 580 Series Outdoor Access Points | Installation Guide 15 Temperature: -40C to 65C (-40F to 149F) If the 580 Series access point is deployed supporting Fiber, PSE, and high user loads in extremely hot temperatures or in hot environments with large solar loading environments, it is strongly recommended to enable Intelligent Power and Temperature Monitoring (IPTM) to ensure continuous uninterrupted operations, allowing the AP to disable specific and user-definable features to ensure continuity and prevent a thermal shutdown of the AP. Storage Temperature: -40C to 70C (-40F to 158F) Humidity: 5% to 93% non-condensing For additional specifications on this product, please refer to the data sheet at www.arubanetworks.com. Regulatory Model Number For the purpose of regulatory compliance certifications and identification, this product has been assigned a unique regulatory model number (RMN). The regulatory model number can be found on the product nameplate label, along with all required approval markings and information. When requesting compliance information for this product, always refer to this regulatory model number. The regulatory model number RMN is not the marketing name or model number of the product. The following regulatory model numbers apply to the 580 Series:
AP-584 RMN: APEX0584 AP-585 RMN: APEX0585 AP-587 RMN: APEX0587 Safety and Regulatory Compliance RF Radiation Exposure Statement: This equipment complies with RF radiation exposure limits. This equipment should be installed and operated with a minimum distance of 13.78 inches (35cm) between the radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Dclaration de la concernant lexposition aux rayonnements frquence radiolectrique (FR): Cet appareil est conforme aux limites dexposition aux rayonnements FR tablies par la FCC. Il doit tre install et utilis une distance minimale de 35 cm (13,78 pouces) entre le radiateur et votre corps, quil opre sur la bande 2,4 GHz ou 5 GHz. Cet metteur ne doit pas tre install ou utilis proximit immdiate dune autre antenne ni dun autre transmetteur. The device could automatically discontinue transmission in case of absence of information to transmit, or operational failure. Note that this is not intended to prohibit transmission of control or signaling information or the use of repetitive codes where required by the technology. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. Toute modification effectue sur cet quipement sans l'autorisation expresse de la partie responsable de la conformit est susceptible d'annuler son droit d'utilisation.
16 Aruba 580 Series Outdoor Access Points | Installation Guide United States This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturers instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio or TV technician for help. Improper termination of access points installed in the United States configured to a non-US model controller is a violation of the FCC grant of equipment authorization. Any such willful or intentional violation may result in a requirement by the FCC for immediate termination of operation and may be subject to forfeiture (47 CFR 1.80). Innovation, Science and Economic Development Canada This Class B digital apparatus meets all of the requirements of the Canadian Interference-Causing Equipment Regulations. In accordance with Industry Canada regulations, this radio transmitter and receiver may only be used with an antenna, the maximum type and gain of which must be approved by Industry Canada. To reduce potential radio interference, the type of antenna and its gain shall be chosen so that the equivalent isotropic radiated power
(EIRP) does not exceed the values necessary for effective communication. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. When operated in 5.15 to 5.25 GHz frequency range, this device is restricted to indoor use to reduce the potential for harmful interference with co-channel Mobile Satellite Systems. This radio transmitter model APEX0584 has been approved by Industry Canada to operate with the antenna types listed in the online ordering guide (link provided below) with the maximum permissible gain indicated. Antenna types not included in this list, having a greater gain than the maximum gain indicated for that type, are strictly prohibited for use with this device. https://www.arubanetworks.com/assets/og/OG_AP-580Series.pdf Innovation, Sciences et Dveloppement conomique Canada Cet appareil contient un ou plusieurs transmetteurs/rcepteurs exempts de licence conformes aux RSS exempts de licence dInnovation, Sciences et Dveloppement conomique Canada. Lutilisation de ce priphrique est soumise aux deux conditions suivantes: (1) Cet appareil ne doit pas produire dinterfrences. (2) Cet appareil doit accepter toutes les interfrences, y compris les interfrences pouvant engendrer un fonctionnement indsirable de lappareil. En cas d'utilisation dans la plage de frquences de 5,15 5,25 GHz, cet appareil doit uniquement tre utilis en intrieur afin de rduire les risques d'interfrence avec les systmes satellites mobiles partageant le mme canal. Ce modle d'metteur radio APEX0584 a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs dans le guide de commande en ligne (lien ci-dessous) avec le gain maximal admissible indiqu. Les types d'antennes non inclus dans cette liste, ayant un gain suprieur au gain maximal indiqu pour ce type, sont strictement interdits pour une utilisation avec cet appareil. https://www.arubanetworks.com/assets/og/OG_AP-580Series.pdf European Union Regulatory Conformance The Declaration of Conformity made under Radio Equipment Directive 2014/53/EU is available for viewing at:
www.hpe.com/eu/certificates. Select the document that corresponds to your devices model number as it is indicated on the product label. Aruba 580 Series Outdoor Access Points | Installation Guide 17 This radio transmitter model has been approved to operate with the antenna types listed in the online ordering guide (link provided below) with the maximum permissible gain indicated. Antenna types not included in this list, having a greater gain than the maximum gain indicated for the type, are strictly prohibited for use with this device. Compliance is only assured if the Aruba approved accessories as listed in the ordering guide are used. http://www.arubanetworks.com/assets/og/OG_AP-580Series.pdf Wireless Channel Restrictions 5150-5350MHz band is limited to indoor only in the following countries; Austria (AT), Belgium (BE), Bulgaria (BG), Croatia (HR), Cyprus (CY), Czech Republic (CZ), Denmark (DK), Estonia (EE), Finland (FI), France (FR), Germany (DE), Greece (GR), Hungary (HU), Iceland (IS), Ireland (IE), Italy (IT), Latvia (LV), Liechtenstein (LI), Lithuania (LT), Luxembourg (LU), Malta (MT), Netherlands (NL), Norway (NO), Poland (PL), Portugal (PT), Romania (RO), Slovakia
(SK), Slovenia (SL), Spain (ES), Sweden (SE), Switzerland (CH), Turkey (TR), United Kingdom (UK(NI)). Radio Frequency Range MHz Max EIRP BLE/Zigbee 2402-2480 Wi-Fi 2412-2472 5150-5250 5250-5350 5470-5725 5725-5850 10 dBm 20 dBm 23 dBm 23 dBm 30 dBm 14 dBm
Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. Please refer to the ArubaOS User Guide/
Instant User Guide for details on restrictions. Medical 1. Equipment not suitable for use in the presence of flammable mixtures. 2. Connect to only IEC 60950-1 or IEC 60601-1 certified products and power sources. The end user is responsible for the resulting medical system complies with the requirements of IEC 60601-1. 3. Wipe with a dry cloth, no additional maintenance required. 4. No serviceable parts, the unit must be sent back to the manufacturer for repair. 5. No modifications are allowed without Aruba approval. Taiwan 1. 2. 3. MPE mW/cm2mW/cm2 Brazil Este equipamento no tem direito proteo contra interferncia prejudicial e no pode causar interferncia em sistemas devidamente autorizados. 18 Aruba 580 Series Outdoor Access Points | Installation Guide Japan Mxico La operacin de este equipo est sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debeaceptar cualquier interferencia, incluyendo la que pueda causar su operacin no deseada. HPE Russia: " " , 125171, .
, , 16, .3, : +7 499 403 4248 : +7 499 403 4677
'HPE Kazakhstan': TOO - (), , 050040, .
, , -, 77/7, /: + 7 727 355 35 50 Kazakhstan
" " , 125171, , , 16A 3, : +7 499 403 4248 : +7 499 403 4677
- (), , 050040, ., , -
, 77/7, /: +7 (727) 355 35 50 Ukraine Hereby, Hewlett Packard Enterprise Company declares that the radio equipment type [The Regulatory Model Number [RMN] for this device can be found in the Regulatory Model Number section of this document] is in compliance with Ukrainian Technical Regulation on Radio Equipment, approved by resolution of the CABINET OF MINISTERS OF UKRAINE dated May 24, 2017, No. 355. The full text of the UA declaration of conformity is available at the following internet address: https://certificates.ext.hpe.com/public/certificates.html
, 6280 -, -, 95002, Aruba 580 Series Outdoor Access Points | Installation Guide 19 Contact Aruba Main Site Support Site https://www.arubanetworks.com https://asp.arubanetworks.com Airheads Social Forums and Knowledge Base https://community.arubanetworks.com/
North America Telephone 1-800-943-4526 1-408-754-1200 International Telephone https://www.arubanetworks.com/support-services/contact-support/
Software Licensing Site https://www.hpe.com/networking/support End-of-Life Information https://www.arubanetworks.com/support-services/end-of-life/
Security Incident Response Team (SIRT) https://www.arubanetworks.com/support-service/security-bulletins/
Email: aruba-sirt@hpe.com Copyright Copyright 2021 Hewlett Packard Enterprise Development LP Open Source Code This product includes code licensed under the GNU General PublicLicense, the GNU Lesser General Public License, and/or certain other open source licenses. A complete machine-readable copy of the source code corresponding to such code is available upon request. This offer is valid to anyone in receipt of this information and shall expire three years following the date of the final distribution of this product version by Hewlett Packard Enterprise Company. To obtain such source code, send a check or money order in the amount of US $10.00 to:
Hewlett Packard Enterprise Company Attn: General Counsel 6280 America Center Drive San Jose, CA 94089 USA Warranty This hardware product is protected by an Aruba warranty. For more details, visit www.hpe.com/us/en/support.html 20 Aruba 580 Series Outdoor Access Points | Installation Guide