FCC ID: Q9DAPEX0565567 Wireless Access Point

Aruba 560 Series Outdoor Access Points Installation Guide The Aruba 560 Series outdoor wireless access points (AP-565 and AP-567) are high-performance, multi-radio wireless devices that can be deployed in either controller-based (ArubaOS) or controllerless (Aruba Instant) network environment. The Aruba 560 Series access points support IEEE 802.11ax standard, delivering high performance with the MIMO

(Multiple-Input, Multiple-Output) technology, while also supporting 802.11a/b/g/n/ac wireless services. Package Contents 560 Series access point Cable gland x 1 USB Type-C console cable x 1 Grounding lug and M4x6 screw x 1 Tools Required Phillips screwdriver (#2 for M4x6 screw) Flat blade screwdriver (Ethernet cable gland cover) 8mm allen or hex key (USB console cover) The weatherproof caps for Ethernet and Console interfaces are connected to the access point, not loose in the package. Mounting kits for use with the 560 Series access points are sold separately. Contact your Aruba sales representative for details. Inform your supplier if there are any incorrect, missing, or damaged parts. If possible, retain the carton, including the original packing materials. Use these materials to repack and return the unit to the supplier if needed. Rev 01 | July 2020 1 Hardware Overview Figure 1 560 Series Access Point USB Console Port, Reset button and LED Air Vent Ethernet Port Grounding Point LED The 560 Series access point is equipped with one LED that indicates the system status of the access point. Table 1 560 Series LED Meanings during Boot Up LED Color/State Meaning System LED Off Red No power to AP Initial power-up Green - Flashing AP booting, not ready Green - Steady AP ready and Gigabit Ethernet connected. The LED turns off after 1200 seconds Green - Yellow, 6 seconds period AP ready and 10/100Mbps Ethernet link established. The LED turns off after 1200 seconds 2 Aruba 560 Series Outdoor Access Points | Installation Guide Table 2 560 Series LED Meanings during Operation LED Color/State Meaning System LED Solid Red General fault - Immediate attention required One blink off every 3 seconds Radio 0 fault (5 GHz) Two quick blink off 0.5 seconds apart cycled every 3 seconds Radio 1 fault (2.4GHz) The 560 Series access point is equipped with one Ethernet port (E0). The Ethernet port is 100/1000Base-T auto-

sensing MDI/MDX, which supports uplink connectivity when linked by an Ethernet cable. Ethernet Port Power The Ethernet port supports PoE-in, allowing the AP to draw power from an 802.3af/802.3at PoE power source.The 560 Series access point supports the Intelligent Power Monitoring (IPM) feature that actively measures the power utilization of the AP and dynamically adapts to the power budget. Table 3 lists operational restrictions when the AP is powered by different power options. Table 3 Power Options and Operational Restriction Power Source 802.3at PoE 802.3af PoE IPM n/a enabled Restrictions No restrictions, all capabilities available. AP starts up in unrestricted mode, but may dynamically apply restrictions depending on the PoE budget and actual power. 802.3af PoE disabled 2.4GHz radio is restricted to 1 spatial stream. Always remember to protect the access point by installing grounding lines. The ground connection must be complete before connecting power to the access point enclosure. Grounding Point USB Type-C Console Port Use the included USB Type-C console cable to connect the access point to a laptop or a serial terminal for direct management. You need a proper 8mm allen or hex key to open the cover of the USB Console port. Reset Button The reset button can be used to reset the access point to factory default settings or turn off/on the LED display. There are two ways to reset the access point to factory default settings:

Reset the AP during normal operation Press and hold down the reset button using a small, narrow object such as a paper clip for more than 10 seconds during normal operation. Aruba 560 Series Outdoor Access Points | Installation Guide 3 Reset the AP while powering up is not powered on via PoE. 1. Press and hold down the reset button using a small, narrow object such as a paper clip while the access point 2. Connect the power supply (PoE) to the access point while the reset button is being held down. 3. Release the reset button on the access point after 15 seconds. To turn off/on the LED display, press and release the reset button using a small, narrow object, such as a paperclip for less than 10 seconds during normal operation of the access point. Before You Begin Refer to the sections below before beginning the installation process.

FCC Statement: Improper termination of access points installed in the United States configured to non-US model controllers will be in violation of the FCC grant of equipment authorization. Any such willful or intentional violation may result in a requirement by the FCC for immediate termination of operation and may be subject to forfeiture (47 CFR 1.80). Pre-Installation Checklist Before installing your access point, be sure that you have the following:

Cat5E or better UTP cable with network access A compatible PoE injector with power cord One of the following network services:

Aruba Discovery Protocol (ADP) DNS server with an A record DHCP Server with vendor specific options Aruba, in compliance with governmental requirements, has designed the 560 Series access points so that only authorized network administrators can change configuration settings. For more information about AP configuration, refer to the AP Software Quick Start Guide.

Access points are radio transmission devices and as such are subject to governmental regulation. Network administrators responsible for the configuration and operation of access points must comply with local broadcast regulations. Specifically, access points must use channel assignments appropriate to the location in which the access point will be used. Outdoor Planning and Deployment Considerations Prior to deploying an outdoor wireless network, the environment must be evaluated to plan for a successful WLAN deployment. Successfully evaluating the environment enables the proper selection of routers and antennas and assists in the determination of their placement for optimal RF coverage. This process is considered WLAN or RF planning and Arubas system engineers can assist in the outdoor planning process. The rules for the 5600-5650 MHz band vary by region. Identifying Specific Installation Locations Use the access point placement map generated by Aruba RF Plan software application to determine the proper installation location(s). Each location should be as close as possible to the center of the intended coverage area and should be free from obstructions or obvious sources of interference. These RF absorbers/reflectors/

interference sources will impact RF propagation and should be accounted for during the planning phase and 4 Aruba 560 Series Outdoor Access Points | Installation Guide adjusted for in RF plan.

Use of this equipment adjacent to or stacked with other equipment should be avoided because it could result in improper operation. If such use is necessary, this equipment and the other equipment should be observed to verify that they are operating normally. Identifying Known RF Absorbers/Reflectors/Interference Sources Identifying known RF absorbers, reflectors, and interference sources while in the field during the installation phase is critical. Make sure that these sources are taken into consideration when you attach an access point to its fixed location. RF absorbers include:

Cement/concreteOld concrete has high levels of water dissipation, which dries out the concrete, allowing for potential RF propagation. New concrete has high levels of water concentration in the concrete, blocking RF signals. Natural ItemsFish tanks, water fountains, ponds, and trees Brick RF reflectors include:

Metal ObjectsMetal pans between floors, rebar, fire doors, air conditioning/heating ducts, mesh windows, blinds, chain link fences (depending on aperture size), refrigerators, racks, shelves, and filing cabinets. Do not place an access point between two air conditioning/heating ducts. Make sure that access points are placed below ducts to avoid RF disturbances. RF interference sources include:

Microwave ovens and other 2.4 or 5 GHz objects (such as cordless phones) Cordless headset such as those used in call centers or lunch rooms Access Point Installation Service to all Aruba products should be performed by trained service personnel only. The 560 Series access point can be installed on a wall or attached to a pole by using mount kits:

Using Mount Kits Part Number Description JW052A JW053A JW054A JW055A AP-270-MNT-V1 long mount kit for wall and vertical pole mounting, 300 mm from vertical mounting asset. AP-270-MNT-V2 short mount kit for wall and vertical pole mounting, 75 mm from vertical mounting asset. AP-270-MNT-H1 mount kit for hanging from inclined or horizontal structure. AP-270-MNT-H2 flush mount kit for wall and ceiling mounting. The 560 Series access point does not ship with any mount kits. These mount kits are available as accessories and must be ordered separately. For installation instructions on AP-270-MNT-V1, AP-270-MNT-V2, AP-270-MNT-H1 and AP-270-MNT-H2 mount kit, please refer to the AP-270-MNT-V1 Installation Guide, AP-270-MNT-V2 Installation Guide, AP-270-MNT-H1 Installation Guide and AP-270-MNT-H2 Installation Guide respectively. Aruba 560 Series Outdoor Access Points | Installation Guide 5

This 560 Series access point is intended for installation in a RESTRICTED ACCESS LOCATION attached to a pole or installed on a wall. Installers should disconnect power before working with or near the access point. Grounding the Access Point The grounding must be completed before powering up the access point. The grounding wire should be #8 AWG. 1. Peel the cover of one end of the grounding wire and place the bare grounding wire into the grounding lug

(included in the package), and press firmly with the crimping pliers. 2. Fasten the grounding lug to the grounding hole on the access point with the screw (included in the package). Connecting the Ethernet Cable To connect the Ethernet cable to the access point, perform the following steps using the Ethernet cable gland that ships with your access point. Failure to use the included Ethernet cable gland can lead to connectivity and POE issues. The cable is not included and must be purchased separately. Purchase a suitable UV-resistant, outdoor rated, CAT 5E or better RJ45 cable for use with the access point. Figure 2 Installing the Ethernet Cable Gland Split Grommet Clip Sealing Nut Gland Body 1. Remove the dust cap from the Ethernet port 2. Slide the sealing nut, clip, split grommet and gland body over the cable. 3. Insert the RJ45 connector to the Ethernet port. 4. Screw the gland body onto the Ethernet port. 5. Combine the two split parts of the grommet over the cable, and move it towards the gland body until it 6. Move the clip towards the gland body, passing over the grommet, until the wavy end of the clip properly fits locates at the recess of the gland body. into the wavy end of the gland body. 7. Screw the sealing nut onto the gland body. Two grommets are provided in the package for use with the Ethernet cables. One is applicable for cables with 4-6 mm diameter, and another is applicable for cables with 6-10 mm diameter. Software For instructions on choosing operating modes and initial software configuration, refer to the AP Software Quick 6 Aruba 560 Series Outdoor Access Points | Installation Guide Start Guide.

Aruba access points are classified as radio transmission devices, and are subject to government regulations of the host country. The network administrator(s) is/are responsible for ensuring that configuration and operation of this equipment is in compliance with their countrys regulations. For a complete list of approved channels in your country, refer to the Aruba Downloadable Regulatory Table at https://www.arubanetworks.com/techdocs/DRT/Default.htm Verifying Post-Installation Connectivity The integrated LEDs on the access point can be used to verify that the access point is receiving power and initializing successfully (see Table 1 and Table 2). Refer to the AP Software Quick Start Guide for further details on verifying post-installation network connectivity. Electrical and Environmental Specifications Electrical Ethernet E0: 100/1000Base-T auto-sensing Ethernet RJ-45 Interfaces Power over Ethernet (IEEE 802.3af and 802.3at compliant) Environmental Operating Temperature: -40C to 55C (-40F to 131F) Humidity: 5% to 93% (RH) non-condensing Storage Temperature: -40C to 70C (-40F to 158F) Humidity: 5% to 93% (RH) non-condensing For additional specifications on this product, please refer to the data sheet at www.arubanetworks.com. Regulatory Model Number For the purpose of regulatory compliance certifications and identification, this product has been assigned a unique regulatory model number (RMN). The regulatory model number can be found on the product nameplate label, along with all required approval markings and information. When requesting compliance information for this product, always refer to this regulatory model number. The regulatory model number RMN is not the marketing name or model number of the product. The following regulatory model numbers apply to the 560 Series:

AP-565 RMN: APEX0565 AP-567 RMN: APEX0567 Safety and Regulatory Compliance

RF Radiation Exposure Statement: This equipment complies with RF radiation exposure limits. This equipment should be installed and operated with a minimum distance of 7.87 inches (20 cm) between the radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Aruba 560 Series Outdoor Access Points | Installation Guide 7

Dclaration de la concernant lexposition aux rayonnements frquence radiolectrique (FR): Cet appareil est conforme aux limites dexposition aux rayonnements FR tablies par la FCC. Il doit tre install et utilis une distance minimale de 20 cm (7.87 pouces) entre le radiateur et votre corps, quil opre sur la bande 2,4 GHz ou 5 GHz. Cet metteur ne doit pas tre install ou utilis proximit immdiate dune autre antenne ni dun autre transmetteur. The device could automatically discontinue transmission in case of absence of information to transmit, or operational failure. Note that this is not intended to prohibit transmission of control or signaling information or the use of repetitive codes where required by the technology. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. Toute modification effectue sur cet quipement sans l'autorisation expresse de la partie responsable de la conformit est susceptible d'annuler son droit d'utilisation. United States This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturers instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio or TV technician for help. Improper termination of access points installed in the United States configured to a non-US model controller is a violation of the FCC grant of equipment authorization. Any such willful or intentional violation may result in a requirement by the FCC for immediate termination of operation and may be subject to forfeiture (47 CFR 1.80). Changes or modifications not expressly approved by the manufacturer could void the users authority to operate the equipment. Industry Canada This Class B digital apparatus meets all of the requirements of the Canadian Interference-Causing Equipment Regulations. In accordance with Industry Canada regulations, this radio transmitter and receiver may only be used with an antenna, the maximum type and gain of which must be approved by Industry Canada. To reduce potential radio interference, the type of antenna and its gain shall be chosen so that the equivalent isotropic radiated power

(EIRP) does not exceed the values necessary for effective communication. This device complies with Industry Canada's license-exempt RSS regulations. Operation of this device is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation. When operated in 5.15 to 5.25 GHz frequency range, this device is restricted to indoor use to reduce the potential for harmful interference with co-channel Mobile Satellite Systems. 8 Aruba 560 Series Outdoor Access Points | Installation Guide Dclaration dIndustrie Canada Ce priphrique est conforme aux rglements RSS exempts de licence dIndustrie Canada. Lutilisation de ce priphrique est soumise aux deux conditions suivantes : (1) ce priphrique ne doit pas provoquer dinterfrences, et (2) ce priphrique doit accepter toute interfrence, y compris les interfrences susceptibles de provoquer un dysfonctionnement. En cas d'utilisation dans la plage de frquences de 5,15 5,25 GHz, cet appareil doit uniquement tre utilis en intrieur afin de rduire les risques d'interfrence avec les systmes satellites mobiles partageant le mme canal. European Union Regulatory Conformance The Declaration of Conformity made under Radio Equipment Directive 2014/53/EU is available for viewing at:

www.hpe.com/eu/certificates. Select the document that corresponds to your devices model number as it is indicated on the product label. Wireless Channel Restrictions 5150-5350MHz band is limited to indoor only in the following countries; Austria (AT), Belgium (BE), Bulgaria (BG), Croatia (HR), Cyprus (CY), Czech Republic (CZ), Denmark (DK), Estonia (EE), Finland (FI), France (FR), Germany (DE), Greece (GR), Hungary (HU), Iceland (IS), Ireland (IE), Italy (IT), Latvia (LV), Liechtenstein (LI), Lithuania (LT), Luxembourg (LU), Malta (MT), Netherlands (NL), Norway (NO), Poland (PL), Portugal (PT), Romania (RO), Slovakia

(SK), Slovenia (SL), Spain (ES), Sweden (SE), Switzerland (CH), Turkey (TR), United Kingdom (UK). Frequency Range MHz Max EIRP Radio Wi-Fi BLE/Zigbee 2402-2480 2412-2472 5150-5250 5250-5350 5470-5725 5725-5850 9 dBm 20 dBm 23 dBm 23 dBm 30 dBm 14 dBm

Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. Please refer to the ArubaOS User Guide/

Instant User Guide for details on restrictions. 1. Equipment not suitable for use in the presence of flammable mixtures. 2. Connect to only IEC 60950-1 or IEC 60601-1 certified products and power sources. The end user is responsible for the resulting medical system complies with the requirements of IEC 60601-1. 3. Wipe with a dry cloth, no additional maintenance required. 4. No serviceable parts, the unit must be sent back to the manufacturer for repair. 5. No modifications are allowed without Aruba approval. Medical Taiwan 1. 2. 3. MPE 1 mW/cm2, : 0.97mW/cm2 Aruba 560 Series Outdoor Access Points | Installation Guide 9 Este equipamento no tem direito proteo contra interferncia prejudicial e no pode causar interferncia em sistemas devidamente autorizados. Brazil Japan Mxico Kazakhstan Ukraine La operacin de este equipo est sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debeaceptar cualquier interferencia, incluyendo la que pueda causar su operacin no deseada. HPE Russia: " " , 125171, .

, , 16, .3, : +7 499 403 4248 : +7 499 403 4677

'HPE Kazakhstan': TOO - (), , 050040, .

, , -, 77/7, /: + 7 727 355 35 50

" " , 125171, , , 16A 3, : +7 499 403 4248 : +7 499 403 4677

- (), , 050040, ., , -

, 77/7, /: +7 (727) 355 35 50 Hereby, Hewlett Packard Enterprise Company declares that the radio equipment type [The Regulatory Model Number [RMN] for this device can be found in the Regulatory Model Number section of this document] is in compliance with Ukrainian Technical Regulation on Radio Equipment, approved by resolution of the CABINET OF MINISTERS OF UKRAINE dated May 24, 2017, No. 355. The full text of the UA declaration of conformity is available at the following internet address: https://certificates.ext.hpe.com/public/certificates.html

, 6280 -, -, 95002, 10 Aruba 560 Series Outdoor Access Points | Installation Guide Contact Aruba Main Site Support Site https://www.arubanetworks.com https://asp.arubanetworks.com Airheads Social Forums and Knowledge Base https://community.arubanetworks.com/

North America Telephone 1-800-943-4526 1-408-754-1200 International Telephone https://www.arubanetworks.com/support-services/contact-support/

Software Licensing Site https://www.hpe.com/networking/support End-of-Life Information https://www.arubanetworks.com/support-services/end-of-life/

Security Incident Response Team (SIRT) https://www.arubanetworks.com/support-service/security-bulletins/

Email: aruba-sirt@hpe.com Copyright Copyright 2020 Hewlett Packard Enterprise Development LP Open Source Code certain other open source licenses. This product includes code licensed under the GNU General PublicLicense, the GNU Lesser General Public License, and/or A complete machine-readable copy of the source code corresponding to such code is available upon request. This offer is valid to anyone in receipt of this information and shall expire three years following the date of the final distribution of this product version by Hewlett Packard Enterprise Company. To obtain such source code, send a check or money order in the amount of US $10.00 to:

Hewlett Packard Enterprise Company Attn: General Counsel 6280 America Center Drive San Jose, CA 94089 USA Warranty This hardware product is protected by an Aruba warranty. For more details, visit www.hpe.com/us/en/support.html Aruba 560 Series Outdoor Access Points | Installation Guide 11

Enterprise company Model: APEX0565 aruba By C IP66/IP67 SPEC: 57V == 400mA (PoE) FCC ID: Q9DAPEX0565567 TP. IC: 4675A-APEX0565567 BY CAN ICES-3 (B)/NMB-3(B) D20 0101 201

==, [R] 201-200422 Gay a6 W52/53: Indoor use only . Te HPE, Postfach 0001,1122 Wien, Austria [G R-C-HPe-APEX0565567 c Us 4012806-01

PE, Pstach 000,122 Wen, Asa IP6G/IPE7 e| |\CE@

aruba eaxz Hewit Pacara Model: APEX0567 SPEC: 57V = 400mA (PoE) FCC ID: Q9DAPEX0565567 IC: 4675A-APEX0565567 CAN ICES.3 (8)NMB-3(8) T em)

[@rcinemocesny eijeneem (A)

=e IB] 201-200422 NY, 1W52/53:Indoor use only _4012807-01

Federal Communications Commission Office of Engineering and Technology Laboratory Division 7435 Oakland Mills Rd Columbia MD 21046-1609 SUBJECT: Class III Permissive Change Application to add DFS Bands for FCC ID:

Q9DAPEX0565567 granted on 08/20/2020 To Whom It May Concern, Regarding the requirements for class III permissive changes identified in the SDR application guide

(KDB 442812 D01 SDR Apps Guide v02r03), the following information must be provided when performing a Class III permissive change. We would like to add operation in 5250-5350 MHz and 5470-5725 MHz UNII DFS bands to our existing FCC Grant. There are no hardware changes implemented on this device, only via Aruba Networks controlled Software new DFS bands will be enabled. Details on how ArubaOS implement and control security in order to prevent specifying/changing radio parameters that would violate FCC Grant are described in submitted Security Description for SDR Application document. The software version covered in:

Original Grant issued 08/20/2020, SW: ArubaOS 8.7.0.0 (Build 75504) This C3PC SW : ArubaOS 8.7.0.0 (Build 75624) Best Regards, Phillip Carranco phillip.carranco@hpe.com

Federal Communications Commission Office of Engineering and Technology Laboratory Division 7435 Oakland Mills Rd Columbia MD 21046-1609 Subject: Request for Confidentiality Confidentiality Request regarding application for certification of FCC ID: Q9DAPEX0565567 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commissions rules

(47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure indefinitely. l l Tune-up Procedure Software Security For U-NII Devices Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission s policy, in order to comply with the marketing regulations in 47 CFT 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachment(s) for 180 days after the grant as outlined in Public Notice DA 04-1705. u Test Setup Photos It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards, ______________________ Phillip Carranco phillip.carranco@hpe.com

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Attn: Office of Engineering and Technology. FCC ID: Q9DAPEX0565567 Models: APEX0565 & APEX0567 Applicant: Aruba Networks Date: August 28,2020 To Whom It May Concern:

We, Aruba Networks submit this formal request to the FCC Authorization and Evaluation Division for an Expedited Review for the DFS radar testing required by KDB 388624 D01 Pre-Approval Guidance (PAG) Procedure on FCC ID: Q9DAPEX0565567 Reasoning for Expedited Review:

The APEX0565567 (FCC ID: Q9DAPEX0565567) and the APIN0504/APIN0505 (FCC ID:

Q9DAPIN0504505) utilize the same Broadcom RF Chipset Model: BCM47622) but have different PCB form factors, housing and Antenna gains. The APEX0565 utilizes 2 x Cross-Polarized Dual-

Band Internal Antennas with gains of 3.2dBi (2.4GHz) and 5.4dBi (5GHz) & the APEX0567 has antenna gains of 6.8dBi (2.4GHz) and 7.1dBi (5GHz). The APIN0504 utilizes 2 (female) RP-SMA connectors for External Antennas with lowest gains of 2.0dBi in (2.4GHz and 5GHz) Band, while the APIN0505 utilized 2 integrated dual-band antennas with gains of 4.9dBi (2.4GHz) and 5.7dBi

(5GHz) Band. FCC ID: Q9DAPIN0504505 DFS Verification testing was performed at the FCC on December 10, 2019. The DFS detection functionality has not been changed between these devices. Please refer to page 2 for the Expedited Review Information table. Sincerely, ____________________________ Signature Name/Position: Phillip Carranco / Manager Regulatory Compliance Phone: 650-236-9490 Email: phillip.carranco@hpe.com

Expedited Review Required Information FCC ID(s) of Previously Granted DFS Devices Q9DAPIN0504505 FCC ID of New Application Q9DAPEX0565567 Technology (802.11x, frame based, MIMO, smart antenna, etc.) Bandwidth information and differences 802.11ax / MIMO 802.11ax / MIMO 20, 40 and 80MHz 20, 40 and 80MHz Antenna Information DFS Testing: 2.0dBi DFS Testing APEX0565: 5.4dBi Differences in DFS functioning, circuitry, software, etc. Uses Broadcom RF Chipset Model: BCM47622 and DFS Uses Broadcom RF Chipset Model: BCM47622 and DFS waveform detection mechanism waveform detection mechanism Supports 2 Tx / 2 Rx paths Supports 2 Tx / 2 Rx paths 18 dBm per path 18 dBm per path MRT Technology (Taiwan) Co Sporton International Inc. Differences between the products such as Tx Power, modulation, receivers, processing circuitry Name of Test Labs for Various Grants

Federal Communications Commission Office of Engineering and Technology Laboratory Division 7435 Oakland Mills Rd Columbia MD 21046-1609 Date: July 14, 2020 Authorization letter regarding application for certification of FCC ID: Q9DAPEX0565567 To whom it may concern, Please be notified that I, Phillip Carranco, have designated Jim Tsai in Sporton International Inc. as the person being responsible for this project and to sign the form 731 and other documentation. Any and all acts carried out by Jim Tsai in Sporton International Inc., on the matters of relating to all processes required in the FCC approval and any communication needed with the national authority, shall have the same legal authority as acts on our own behalf. We further certifies that neither the applicant nor any party to this application, as defined in 47 CFR Ch. 1.2002 (b), is subject to a denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1998, 21 U.S.C 862. This authorization is limited to the product of as following:

FCC ID: Q9DAPEX0565567 If you have any acknowledgement and response, please send it to Sporton International Inc. directly. Should you have any questions or comments regarding this matter, please have my best attention. Sincerely yours, ____ Compliance Manager Contact Person: Phillip Carranco E-mail: phillip.carranco@hpe.com

Federal Communications Commission Office of Engineering and Technology Laboratory Division 7435 Oakland Mills Rd Columbia MD 21046-1609 Date: July 14, 2020 Confidentiality Request regarding application for certification of FCC ID: Q9DAPEX0565567 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commissions rules

(47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure indefinitely. l l Block Diagram l l Operational Description l Tune-up Procedure Schematics Parts List Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission s policy, in order to comply with the marketing regulations in 47 CFT 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachment(s) for 180 days after the grant as outlined in Public Notice DA 04-1705. u External Photos u Internal Photos u Test Setup Photos u User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards, ____________________________ Compliance Manager Contact Person: Phillip Carranco E-mail: phillip.carranco@hpe.com