all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 2 |
|
Users Manual Revised | Users Manual | 1.18 MiB | July 10 2003 | |||
1 2 | Test Setup Photos | July 10 2003 | ||||||
1 2 | Cover Letter(s) | July 10 2003 | ||||||
1 2 | Cover Letter(s) | July 10 2003 | ||||||
1 2 | Cover Letter(s) | July 10 2003 | ||||||
1 2 | Cover Letter(s) | July 10 2003 | ||||||
1 2 | Cover Letter(s) | July 10 2003 | ||||||
1 2 | Test Report | July 10 2003 | ||||||
1 2 | External Photos | July 10 2003 | ||||||
1 2 | Internal Photos | July 10 2003 | ||||||
1 2 | ID Label/Location Info | July 10 2003 | ||||||
1 2 | RF Exposure Info | July 10 2003 | ||||||
1 2 | Test Setup Photos | July 10 2003 | ||||||
1 2 | Cover Letter(s) | July 10 2003 | ||||||
1 2 | Cover Letter(s) | July 10 2003 | ||||||
1 2 | Cover Letter(s) | July 10 2003 | ||||||
1 2 | Test Setup Photos | July 10 2003 | ||||||
1 2 | ID Label/Location Info | July 10 2003 | ||||||
1 2 | Test Report | July 10 2003 |
1 2 | Users Manual Revised | Users Manual | 1.18 MiB | July 10 2003 |
7/29/03 FINAL DRAFTCONFIDENTIAL Aruba 52 Wireless Access Point TM Installation Guide 180 Great Oaks Blvd. Ste B San Jose, California 95119 Net www.arubanetworks.com Tel 408.227.4500 Fax 408.227.4550 7/29/03 FINAL DRAFTCONFIDENTIAL Copyright Copyright 2003 Aruba Wireless Networks, Inc. All rights reserved. Specifications in this manual are subject to change without notice. Originated in the USA. Trademarks Aruba 52, Aruba 5000, and AirOS are trademarks of Aruba Wireless Networks in the United States and certain other countries. The K & Lock design is a registered trademark of the Kensington Technology Group in the United States and certain other countries. Any other trademarks appearing in this manual are owned by their respective companies. ii Aruba 52 Installation Guide Part 0500007B August 2003 7/29/03 FINAL DRAFTCONFIDENTIAL Compliance FCC - Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
Reorient the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
Consult the dealer or an experienced radio/TV technician for help FCC Caution: To assure continued compliance, use only shielded interface cables when connecting to computer or peripheral devices. Any changes or modifications not expressly approved by the party respon-
sible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION STATEMENT: FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environ-
ment. This equipment should be installed and operated with a minimum distance of 20 centimeters (8 inches) between the radiator and your body. This transmitter must not be co-located or operating in con-
junction with any other antenna or transmitter. Radio Frequency Interference Requirements This device is restricted to indoor use due to its operation in the 5.15 to 5.25 GHz frequency range. The FCC requires this product to be used indoors to reduce the potential for harmful interference to co-chan-
nel Mobile Satellite systems. High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and/or damage this device. Industry Canada - Class B This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled Digital Apparatus, ICES-003 of the Department of Communications. Cet appareil numrique respecte les limites de bruits radiolectriques applicables aux appareils numriques de Classe B prescrites dans la norme sur le matriel brouilleur: Appareils Numriques, NMB-003 dicte par le ministre des Communications. Aruba 52 iii Installation Guide 7/29/03 FINAL DRAFTCONFIDENTIAL iv Aruba 52 Installation Guide Part 0500007B August 2003 7/29/03 FINAL DRAFTCONFIDENTIAL Contents Chapter 1 Preface . vii Related Documents. vii Text Conventions . viii Contacting Aruba Wireless Networks . ix Introduction . 1 Product Features . 1 Ethernet Compatibility . 2 Radio Characteristics . 2 Power Over Ethernet . 2 Physical Description . 3 Package Checklist . 3 Top Panel . 4 Rear Panel . 6 Chapter 2 Setup & Installation . 7 Requirements . 7 Select a Network Topology . 8 Perform Initial Setup . 10 Direct SPOE to the Aruba WLAN Switch . 10 Direct Terminal Connection . 13 Configure the Aruba 52. 15 Mount the Aruba 52 . 18 Free-Standing Placement . 19 Using the Built-In Mounting Slots . 19 Using the Optional Mounting Kit. 21 Contents v 7/29/03 FINAL DRAFTCONFIDENTIAL Connect Required Cables . 25 Direct SPOE to the Aruba WLAN Switch . 25 LAN or POE Connection. 26 Appendix A Port Specifications . 29 Console Port . 29 FE Port . 30 SPOE Adapter . 31 Appendix B Product Specifications . 33 vi Aruba 52 Installation Guide Part 0500007B August 2003 7/29/03 FINAL DRAFTCONFIDENTIAL Preface The preface includes the following information:
A list of related documentation for further reading
A key to the various text conventions used throughout this manual
Aruba Wireless Networks support and service information Related Documents The following items are part of the complete documentation for the Aruba system:
Aruba 5000 Installation Guide (Part No. 0500001A, June 2003)
Aruba AirOS v1.1 Users Guide (Part No. 0500002B, August 2003)
Aruba 52 Installation Guide (Part No. 0500007B, August 2003) Preface vii 7/29/03 FINAL DRAFTCONFIDENTIAL Text Conventions The following conventions are used throughout this manual to emphasize important concepts:
TABLE 1 Text Conventions Type Style Italics System items Commands
<Arguments>
[ Optional ]
{ Item A | Item B }
Description This style is used to emphasize important terms and to mark the titles of books. This fixed-width font depicts the following:
Sample screen output
System prompts
Filenames, software devices, and certain commands when men-
tioned in the text. In the command examples, this bold font depicts text that the user must type exactly as shown. In the command examples, italicized text within angle brackets rep-
resents items that the user should replace with information appropri-
ate to their specific situation. For example:
# send <text message>
In this example, the user would type send at the system prompt exactly as shown, followed by the text of the message they wish to send. Do not type the angle brackets. In the command examples, items enclosed in brackets are optional. Do not type the brackets. In the command examples, items within curled braces and separated by a vertical bar represent the available choices. Enter only one choice. Do not type the braces or bars. viii Aruba 52 Installation Guide Part 0500007B August 2003 7/29/03 FINAL DRAFTCONFIDENTIAL Contacting Aruba Wireless Networks Web Site
Main Site
Support E-mail
Sales
Support http://www.arubanetworks.com http://www.arubanetworks.com/support sales@arubanetworks.com support@arubanetworks.com Telephone Numbers
Main
Fax
Sales
Support 408-227-4500 408-227-4550 408-754-1201 408-754-1200 Preface ix 7/29/03 FINAL DRAFTCONFIDENTIAL x Aruba 52 Installation Guide Part 0500007B August 2003 7/29/03 FINAL DRAFTCONFIDENTIAL CHAPTER 1 Introduction The Aruba 52 is part of a comprehensive wireless network solution. The device works in con-
junction with the Aruba 5000 WLAN Switch and can act as a wireless access point or air mon-
itor. As a wireless access point, the Aruba 52 provides transparent, secure, high-speed data com-
munications between wireless network devices (fixed, portable, or mobile computers with IEEE 802.11a, 802.11b, or 802.11g wireless adapters) and the wired LAN. As a wireless air monitor, a uniquely Aruba feature, the Aruba 52 enhances wireless networks by collecting statistics, monitoring traffic, detecting intrusions, enforcing security policies, balancing wireless traffic load, self-healing coverage gaps, and more. Product Features
Wireless dual-band transceiver
Dual, omnidirectional antennas for reception diversity
Protocol-independent networking functionality
802.11a up to 54 Mbps data rate per channel: offers a high data rate and reliable wireless connectivity
802.11b up to 11 Mbps data rate per channel: provides an alternative to wired LANs that can dramatically cut costs
802.11g up to 54 Mbps data rate per channel: backwards compatible with 802.11b
Compatible with IEEE 802.3af Power Over Ethernet (POE)
Seamless connectivity to wired LANs augment existing networks quickly and easily
Can be centrally managed, configured, and upgraded through the Aruba WLAN Switch to take advantage of network changes and security improvements Introduction 1 Chapter 1 7/29/03 FINAL DRAFTCONFIDENTIAL Ethernet Compatibility The Aruba 52 attaches to 10/100 Mbps Ethernet (FE) LAN segments that utilize 10Base-T/100Base-TX (twisted-pair) wiring. The device appears as an Ethernet node and performs a routing function by moving packets between the wired LAN and remote worksta-
tions on the wireless infrastructure. Radio Characteristics For IEEE 802.11a operation, the Aruba 52 uses a radio modulation technique known as Orthogonal Frequency Division Multiplexing (OFDM), and a shared collision domain
(CSMA/CA). It operates in the 5GHz Unlicensed National Information Infrastructure
(UNII) band. Data is transmitted over a half-duplex radio channel operating at up to 54 Megabits per second (Mbps). For IEEE 802.11b operation, the Aruba 52 uses the IEEE 802.11 High-Rate Direct Sequence
(HRDS) specification, and a shared collision domain (CSMA/CA). It operates in the 2.4GHz Industrial/Scientific/Medical (ISM) band. The ISM band is available worldwide for unli-
censed use. Data is transmitted at speeds of up to 11 Mbps. For IEEE 802.11g operation, the Aruba 52 uses ODFM and a shared collision domain
(CSMA/CA). It operates in the 2.4GHz Industrial/Scientific/Medical (ISM) band. The ISM band is available worldwide for unlicensed use. Data is transmitted at speeds of up to 54 Mbps. Power Over Ethernet The Aruba 52 supports the IEEE 802.3af standard for Power Over Ethernet (POE). With this feature, the Aruba 52 can accept electrical power from a compatible POE-capable device to which it is connected, directly over the FE cable. POE eliminates the need to provide separate power outlets in environments that are difficult or undesirable to wire for electricity. The Aruba 52 supports POE only when the FE port is connected to an IEEE 802.3af compli-
ant device (such as the Aruba 5000 WS-5032 Line Card). 2 Aruba 52 Installation Guide Part 0500007B August 2003 7/29/03 FINAL DRAFTCONFIDENTIAL Physical Description Package Checklist The Aruba 52 package includes:
R E A D Y L A N
. A
. B FIGURE 1-1 Package Contents
One Aruba 52 Wireless Access Point
Non-slip rubber foot-pads
One AC power adapter (3.3 VDC, 4 A) and power cord
Assorted documentation The following optional items can also be ordered for the Aruba 52:
FIGURE 1-2 Optional Items
Mounting kit: cradle and screws
Serial & Power Over Ethernet (SPOE) adapter Inform your supplier if there are any incorrect, missing or damaged parts. If possible, retain the carton, including the original packing materials. Use them again to repack the product in case there is a need to return it. Introduction 3 Chapter 1 7/29/03 FINAL DRAFTCONFIDENTIAL Top Panel 1 2 1 READY LAN
.A
.B/.G 3 2 FIGURE 1-3 Aruba 52 Top Panel 1 Dual, omnidirectional Antennas for Wireless Communications (on sides) The antennas swivel and should be oriented vertically (straight up and down) away from the chassis for best performance. 2 Air Vents (on sides) These vents promote proper air circulation for cooling the device. Do not allow these vents to be obstructed by mounting equipment, network cables, or any other material. 4 Aruba 52 Installation Guide Part 0500007B August 2003 7/29/03 FINAL DRAFTCONFIDENTIAL 3 Indicator LEDs During operation, the Aruba 52 LEDs provide the following information:
TABLE 1-1 Aruba 52 LEDs LED Ready LAN
.A
.B/.G State Off Green Flashing Off Green Flashing Off Green Flashing Off Green Flashing Description The device is off or initializing. The device has passed self-test and is operating. The device is running a self-test or loading new software. If the condition persists for more than one minute, refer to the trou-
bleshooting information in Appendix A. No link on the FE port on back of the device. Link detected on the FE port. Transmitting or receiving data across the FE port. Flashing rate is proportional to your network activity. The 802.11a wireless interface is disabled or down. The device is operating as an 802.11a access point. The device is operating as an 802.11a air monitor. The 802.11b/g wireless interface is disabled or down. The device is operating as an 802.11b/g access point. The device is operating as an 802.11b/g air monitor. NOTELEDs on the Aruba WLAN Switch provide additional status and security informa-
tion about connected APs. See the Aruba 5000 Installation Guide and Aruba AirOS Users Guide for more information. Introduction 5 Chapter 1 7/29/03 FINAL DRAFTCONFIDENTIAL Rear Panel 1 2 3 4 5 FIGURE 1-4 Aruba 52 Rear Panel 1 Kensington Security Slot This slot is compatible with a Kensington MicroSaver Security Cable (not included) which can be used to prevent the unauthorized removal of the Aruba 52 from its installed location. To secure the Aruba 52, wrap a security cable around an immovable object, insert the cables lock into the Kensington Security Slot, and turn the key. 2 Console Port This port has a 9-pin, female serial connector. It is used primarily to connect a terminal during initial setup of the Aruba 52. See Appendix A for port details. Using the optional SPOE adapter, this port can also be connected directly to an FE port on an Aruba WLAN Switch that supports SPOE (see Power Over Ethernet on page 2). This direct connection provides extra maintenance options during normal operation. 3 FE Port This port attaches the Aruba 52 to 10Base-T/100Base-TX (twisted-pair) Ethernet LAN seg-
ments. The port automatically adjusts MDI/MDX to accept either straight-through or cross-
over cables. See Appendix A for port details. This port also supports POE (see Power Over Ethernet on page 2). When POE is used, a straight-through cable is required. 4 DC Power Socket This socket is used to connect the included AC power adapter. If POE is being used to supply power to the Aruba 52, the power adapter is not necessary. 5 Mounting Slots (on bottom) The keyhole-shaped slots on the bottom of the chassis are used for mounting the Aruba 52. 6 Aruba 52 Installation Guide Part 0500007B August 2003 7/29/03 FINAL DRAFTCONFIDENTIAL CHAPTER 2 Setup & Installation This chapter covers the following topics:
Requirements for installing the Aruba 52
Supported network topology options
Initial setup of the Aruba 52
Physical mounting of the device
Connecting the required cables
Testing the installation Requirements Before you install the Aruba 52, you must have the following:
An operational Aruba WLAN Switch with a valid IP route to the LAN segment to which the access point or air monitor will be connected.
An appropriate physical location for the new access point or air monitor. We recommend an up-to-date site survey to help determine the optimal location for your Aruba 52. See your Aruba AirOS Software Guide for instructions on using the Aruba WLAN Switchs built-in planning tools.
Client devices with IEEE 802.11a, 802.11b, or 802.11g compliant wireless Ethernet adapters with TCP/IP compatible protocol installed.
One of the following power sources for the access point or air monitor:
An AC power outlet rated at 100~240 V, 50~60 Hz.
Power Over Ethernet (POE) capability on the device to which the Aruba 52 is con-
nected (see Power Over Ethernet on page 2). NOTEWhen installing the Aruba 52 in plenums or air-handling spaces, as described in NEC (2002) Article 300.22(C), the device must be powered using POE, and not the included AC power adapter. Setup & Installation 7 Chapter 2 7/29/03 FINAL DRAFTCONFIDENTIAL Select a Network Topology The Aruba 52 can be installed in your network using the following topologies:
1 Direct SPOE Installation Serial, Power
& Ethernet Aruba 5000 w/SPOE Aruba 50 Data Network Mgmt. Network 2 POE Installation Management Workstation LAN Power & Ethernet LAN Switch w/POE Management Workstation Aruba 5000 Aruba 50 Serial Console
(Initial Setup Only) 3 LAN Installation Ethernet LAN LAN Data Network Mgmt. Network Management Workstation Aruba 5000 Power Adapter Aruba 50 Serial Console
(Initial Setup Only) Data Network Mgmt. Network FIGURE 2-1 Aruba 52 Topology Options 8 Aruba 52 Installation Guide Part 0500007B August 2003 7/29/03 FINAL DRAFTCONFIDENTIAL 1 Direct Serial & Power Over Ethernet (SPOE) to the Aruba WLAN Switch (recom-
mended) In this topology, both the console and 10/100 Mbps Ethernet (FE) ports on the Aruba 52 are connected to the SPOE adapter. An 8-conductor, Category 5 UTP, straight-through FE cable connects the adapter directly to the Aruba WLAN Switch with no intervening hubs, routers, or other network equipment. The network port on the Aruba WLAN Switch must include optional SPOE capability (see Power Over Ethernet on page 2). This topology provides the following features:
10/100 Mbps Ethernet connectivity
Electrical power through the FE cable
Serial console connectivity through the FE cable
Extra console maintenance options during normal operation 2 POE connection through the LAN In this topology, the Aruba 52 is connected to the LAN through a hub or switch that is POE compatible (see Power Over Ethernet on page 2). An 8- or 4-conductor, Category 5 UTP, straight-through FE cable is required. Initial setup requires a local serial console. This topology provides the following features:
10/100 Mbps Ethernet connectivity (depending on the connecting port)
Electrical power through the FE cable
Versatile placement of the Aruba WLAN Switch and Aruba 52s within the network 3 Connection to a non-POE network port on the Aruba WLAN Switch or other net-
work device In this topology, the Aruba 52 is connected to the Aruba WLAN Switch either directly or through the LAN. An 8- or 4-conductor, Category 5 UTP, straight-through or crossover FE cable may be used. Initial setup requires a local serial console. Electrical power is supplied using the included AC power adapter. This topology provides the following features:
10/100 Mbps Ethernet connectivity (depending on the connecting port)
Versatile placement of the Aruba WLAN Switch and Aruba 52s within the network Setup & Installation 9 Chapter 2 7/29/03 FINAL DRAFTCONFIDENTIAL Perform Initial Setup The Aruba 52 requires some initial configuration before it will operate. The method used for connecting to the Aruba 52 for initial setup depends on your intended network topology (see Figure 2-1 on page 8). Direct SPOE to the Aruba WLAN Switch Use this procedure when connecting the Aruba 52 directly to an SPOE-compatible network port on the Aruba WLAN Switch (see Power Over Ethernet on page 2). SPOE provides 10/100 Mbps Ethernet, serial connection, and power over one cable. NOTEIf connecting the Aruba 52 through the LAN or to a non-SPOE network port on the Aruba WLAN Switch, see the instructions on page 13. 1 Connect the SPOE adapter to the Aruba 52. A B Connect the adapters 9-pin serial connector to the Console port on the back of the Aruba 52. Connect the adapters male RJ-45 plug to the FE port on the back of the Aruba 52. 2 Connect the Aruba 52 to the Aruba WLAN Switch. CAUTIONTo prevent personal injury or damage to equipment, be sure to com-
ply with electrical grounding standards during all phases of installation and operation of the AP. Do not allow theAruba 52 to contact metal which is connected a different electrical ground than the Aruba WLAN Switch. Also, never connect the AP or WLAN switch to external storm grounding sources. The connection between the Aruba 52 and the Aruba WLAN Switch requires an 8-conduc-
tor, Category 5 UTP, straight-through FE cable with RJ-45 connectors (see Appendix A for port specifications). A B Connect one end of the FE cable directly to the RJ-45 socket on the SPOE adapter that was attached to the Aruba 52 in the previous step. Connect the other end of the FE cable directly to an available SPOE network port on the Aruba WLAN Switch. NOTEThe Aruba 52 must be connected to the Aruba WLAN Switch without any inter-
vening hubs, routers, or other networking equipment. 10 Aruba 52 Installation Guide Part 0500007B August 2003 7/29/03 FINAL DRAFTCONFIDENTIAL 3 Telnet to the Aruba WLAN Switch Serial-Over-Ethernet (SOE) interface. Use a Telnet client on your management workstation to connect to theAruba WLAN Switch IP address using logical port 2300. The connection command may vary depending on the spe-
cific software used, but commonly appears as follows:
> telnet <switch IP address> 2300 4 When prompted, log in to the Aruba WLAN Switch as the administrator:
user: admin password: <administrator password (not displayed)>
This will present you with the Aruba WLAN Switch SOE console prompt:
Available commands:
baud [9600|19200|38400|57600|115200]
connect <slot/port>
exit (no args) soe>
5 Connect to the Aruba WLAN Switch port to which the Aruba 52 is physically attached:
soe> connect <slot number>/<port number>
where slot number is the physical slot of the line card in the WLAN switch, and port number is the physical port. Setup & Installation 11 Chapter 2 7/29/03 FINAL DRAFTCONFIDENTIAL 6 From the Aruba 52 console, access the boot prompt. Depending on the Aruba 52 status, you will see one of the following on your terminal:
Autoboot countdownThe countdown prompt allows you to interrupt the normal star-
tup process and access the boot prompt where initial configuration is performed. APBoot 1.0.6 (May 19 2003 - 14:52:48) CPU: MPC8245 Revision 16.20 at 192 MHz: 16 kB I-Cache 16 kB D-Cache Watchdog enabled Board: ASAP Local Bus at 96 MHz DRAM: 16 MB POST: passed FLASH: 4 MB PCI: scanning bus0 ... dev fn venID devID class rev MBAR0 MBAR1 MBAR2 MBAR3 00 00 1057 0006 060000 12 00000008 00000000 00000000 00000000 13 00 1317 0985 020000 11 fe000001 f0000000 00000000 00000000 14 00 168c 0013 020000 01 f0010000 00000000 00000000 00000000 In: serial Out: serial Err: serial Net: an983b#0 Hit any key to stop autoboot: 0 To access the boot prompt, press any key (such as <Enter>) before the timer expires. If the countdown expires before you can interrupt it, turn the device off and then back on again (by unplugging and reattaching the FE cable) and try again.
TFTP time outIf the Aruba 52 cannot locate or download its image file, the following type of output is repeatedly displayed:
BOOTP broadcast 1 DHCP IP address: 10.3.9.172 DHCP subnet mask: 255.255.255.0 DHCP def gateway: 10.3.9.254 DHCP DNS server: 10.1.1.2 ARP broadcast 1 for 10.3.9.254 TFTP from server 10.10.10.10; our IP address is 10.3.9.172; sending through gateway 10.3.9.254 Filename 'sap.bin'. Load address: 0x100000 Loading: T T T T T T T T T Retry count exceeded; starting again Press <Control-C> to interrupt this process and access the boot prompt. From the boot prompt (apboot>), follow the instructions on page 15 to configure Aruba 52. 12 Aruba 52 Installation Guide Part 0500007B August 2003 7/29/03 FINAL DRAFTCONFIDENTIAL Direct Terminal Connection Use this procedure when connecting the Aruba 52 through the LAN or to a non-SPOE net-
work port on the Aruba WLAN Switch. Under these topologies, a direct terminal connection is required for initial setup. NOTEIf connecting the Aruba 52 directly to a SPOE network port on the Aruba WLAN Switch, see the instructions on page 10. 1 Connect power to the Aruba 52. CAUTIONBe sure to comply with electrical grounding standards during all phases of installation and operation of the AP. Do not allow the Aruba 52 or power adapter (if used) to be connected to or make contact with metal or power outlets on a different electrical ground than the device to which it is connected. Also, never con-
nect the AP to external storm grounding sources. The Aruba 52 can receive electrical power using the following options:
POEIf connecting the Aruba 52 to a device that supplies IEEE 802.3af compliant POE
(see Power Over Ethernet on page 2), no additional power connection is necessary.
Power Outlet NOTEWhen the Aruba 52 is installed in an air-handling space, as described in NEC
(2002) Article 300.22(C), POE must be used instead of a power outlet. If local regulations and practices permit, connect the included AC power adapter cable to the DC power socket on the rear panel of the Aruba 52 and plug it into an appropriate power outlet. CAUTIONTo prevent personal injury or damage to equipment, use only the AC power adapter supplied with this device. NOTEThe indicator LEDs on top of the Aruba 52 will remain dark during this procedure. Setup & Installation 13 Chapter 2 7/29/03 FINAL DRAFTCONFIDENTIAL 2 Set up your local terminal. This procedure requires a terminal or computer running terminal emulation software with the following settings:
TABLE 2-1 Console Terminal Settings Baud Rate Data Bits 9600 8 Parity None Stop Bits Flow Control 1 None 3 Connect the terminal directly to the Aruba 52. Use a standard serial cable to connect the Aruba 52 console port to a serial port on your termi-
nal (see Appendix A for port specification). 4 5 Establish console communication. Press <Enter> a few times to establish communication between the Aruba 52 and terminal. Interrupt the boot cycle to access the Aruba 52 boot prompt. While connected directly to your terminal, the Aruba 52 will remain in a boot cycle looking for an Aruba WLAN Switch from which to download its software and configuration:
BOOTP broadcast 1 DHCP IP address: 10.3.9.172 DHCP subnet mask: 255.255.255.0 DHCP def gateway: 10.3.9.254 DHCP DNS server: 10.1.1.2 ARP broadcast 1 for 10.3.9.254 TFTP from server 10.10.10.10; our IP address is 10.3.9.172; sending through gateway 10.3.9.254 Filename 'sap.bin'. Load address: 0x100000 Loading: T T T T T T T T T Retry count exceeded; starting again Press <Control-C> at any time to interrupt the boot cycle. You will be presented with the boot prompt (apboot>). Follow the instruction on page 15 to configure the device. 14 Aruba 52 Installation Guide Part 0500007B August 2003 7/29/03 FINAL DRAFTCONFIDENTIAL Configure the Aruba 52 1 From the boot prompt, set the intended location for the Aruba 52:
apboot> setenv location <building number>.<floor number>.<device number>
If you performed the recommended site survey using the Aruba WLAN Switchs built-in planning tools, the location data for all access points and air monitors can be found on the tools deployment screen (see the Aruba AirOS Software Guide). If you plan to manually generate the location data, record the following information for each access point and air monitor. It will be required when configuring the Aruba WLAN Switch. Building Number Floor Number Device Number A unique number (1-255) is required for each building in your campus. Within any building, a unique number (1-255) is required for each floor. Within any floor, a unique number (1-65536) is required for each access point or air monitor. Device Description Note the intended function of the device (access point or dedicated air X, Y Coordinates monitor) and a brief description of its service location. For each access point and air monitor, measure its X and Y position (in feet) relative to the bottom-left corner of the building plan as seen from overhead. For example:
Y
. t f 2 6 2 98 0,0 126 X 418 ft. Use the same fixed point and orientation for all floors in a building. Setup & Installation 15 Chapter 2 7/29/03 FINAL DRAFTCONFIDENTIAL 2 Specify host information, if necessary. The Aruba 52 uses the default host name aruba-master to find the host Aruba WLAN Switch and download its software. This assumes that your DNS has been configured to resolve aruba-master to the master Aruba WLAN Switch IP address.
If DNS is available, the AP will use servername environment variable to find the host and download the AP software image and the configuration file (unless serverip and/or master are set). If DNS is not available, then the IP address of the server hosting the AP software image and the address of the server hosting the configuration file must be specified. This is accomplished using the environment variables serverip and master respectively. CAUTIONThe serverip and master environment variables take precedence over the servername variable. Therefore, if you set serverip or naster the AP will use those addresses to search for the software image and the configuration file instead of looking for the server specified in servername. NOTEThe software image and the configuration file are usually stored on the same server.
If you are not using DNS, you must manually configure the Aruba 52 with the IP address of the master Aruba WLAN Switch:
apboot> setenv serverip <switch IP address>
apboot> setenv master <switch IP address>
If you are using DNS but wish to specify a different host, use the following command:
apboot> setenv servername <image host name>
16 Aruba 52 Installation Guide Part 0500007B August 2003 7/29/03 FINAL DRAFTCONFIDENTIAL Table 2-2 summarizes the server environment variables discussed above. TABLE 2-2 Server Enviornment Variable Variable Name servername Default Value aruba-master serverip n/a Use DNS name of the master M-switch. IP address of the TFTP server. master n/a IP address of the master M-switch. Comments Also serves as the TFTP servername if serverip is not set. Overides servername for TFTP image download. Use only if DNS is unavail-
able or must be bypassed. Overides servername. Use if DNS is unavailable or must be bypassed. 3 Specify an IP address, if necessary. If using DHCP, the Aruba 52 will obtain its IP address automatically and this step can be skipped. Otherwise, the AP must be manually configured with a static IP address using the fol-
lowing commands:
apboot> setenv ipaddr <static IP address for the AP>
apboot> setenv netmask <static IP address mask>
apboot> setenv gatewayip <default gateway IP address>
4 Save the configuration and reboot the Aruba 52. apboot> save apboot> boot Once the Aruba 52 boots, disconnect it and mount it in its intended service location (see instructions on page 18). Setup & Installation 17 Chapter 2 7/29/03 FINAL DRAFTCONFIDENTIAL Mount the Aruba 52 When initial setup is complete, mount the Aruba 52 in its intended service location. Select a location as close as possible to the center of the intended coverage area. If necessary, use the Aruba WLAN Switchs built-in site survey software to determine the optimum loca-
tions for your access points and air monitors (see your Aruba AirOS Software Guide). The service location should be free from obstructions or obvious sources of interference. Nor-
mally, the higher you place an access point or air monitor, the better its performance. The Aruba 52 can be mounted in the following ways:
2 R E A D Y L A N
. A
. B READY LAN
.A
.B 1 3 R E A D Y L A N
. A
. B FIGURE 2-2 Aruba 52 Mounting Options Flat on a table or shelf (with the LEDs on top) Upright on a wall (with the port connectors on top) using the built-in mounting slots or the optional mounting kit Suspended from above (with the LEDs on bottom) using the optional mounting kit 1 2 3 CAUTIONFor safety purposes, do not mount the Aruba 52 sideways (with the air vents on top and bottom). 18 Aruba 52 Installation Guide Part 0500007B August 2003 7/29/03 FINAL DRAFTCONFIDENTIAL Free-Standing Placement To place the Aruba 52 on a flat table or shelf, first attach the included non-skid foot-pads to the bottom of the chassis. CAUTIONDo not place the Aruba 52 in any place where it could fall on people or equipment. For more secure installation, use the optional mounting kit. Using the Built-In Mounting Slots The keyhole-shaped slots on the bottom of the Aruba 52 can be used to attach the device to a wall or shelf. CAUTIONDo not use the mounting slots to hang the Aruba 52 from the ceiling or in any place where it could fall on people or equipment. For more secure installa-
tion, use the optional mounting kit. To hang the Aruba 52, perform the following steps. 1 Install three screws in the wall or shelf as shown in Figure 2-3:
Screw/Nail Positions
(fastened to wall or shelf) Measuring Point 7.27 cm
(2.86") 7.27 cm
(2.86") 5.5 cm
(2.17") READY LAN
.A
.B Orientation Screw/Nail Dimensions Maximum Minimum 7.0 mm 3.0 mm 0.27"
0.12"
5.8 mm 2.0 mm 3.8 mm clearance from surface 1.3 mm clearnace from surface 0.23"
0.08"
0.15"
clearance from surface 0.05"
clearance from surface FIGURE 2-3 Mounting Screw Specifications If attaching the device to drywall, we recommend using appropriate wall anchors (not included) as shown in Figure 2-4. Setup & Installation 19 Chapter 2 7/29/03 FINAL DRAFTCONFIDENTIAL 2 Align the Aruba 52 mounting slots to capture the surface screws. B
.A LAN READY FIGURE 2-4 Hanging the Aruba 52 on Screws 3 Secure the Aruba 52, if desired. To prevent the unauthorized removal of the Aruba 52 from its installed location, use a Kens-
ington MicroSaver Security Cable (not included). Wrap the security cable around an immov-
able object, insert the cables lock into the Kensington Security Slot on the back of the Aruba 52, and turn the key. 4 Orient the antennas. For best performance, swivel the antennas so that they are oriented vertically (see Figure 2-2 on page 18). Once mounting is complete, connect the required cables (see instructions on page 25). 20 Aruba 52 Installation Guide Part 0500007B August 2003 7/29/03 FINAL DRAFTCONFIDENTIAL Using the Optional Mounting Kit Use the optional mounting kit to attach the Aruba 52 to a wall, shelf, or ceiling. NOTEDo not attach the rubber foot-pads to the Aruba 52 when using the mounting kit. Wall, Shelf, or Solid Ceiling Mount Attach the mounting cradle to the mounting surface. 1S Place the flat side of the cradle against the mounting surface. If attaching the cradle to a wall, orient it so that the cable tie anchors are positioned at the top. If attaching the cradle to a table, shelf, or solid ceiling, orient the cable tie anchors toward the cable route. CAUTIONDo not use screws to attach the mounting cradle to a suspended ceil-
ing or other structurally weak surface. For suspended ceilings, use the T-rail clips as described on page 23 instead. Use the four #6 screws (or equivalent) to secure the cradle to the solid surface. If attaching the cradle to drywall, we recommend using appropriate wall anchors (not included) as show below:
FIGURE 2-5 Attaching the Mounting Cradle Setup & Installation 21 Chapter 2 7/29/03 FINAL DRAFTCONFIDENTIAL 2 Place the Aruba 52 into the mounting cradle as shown in Figure 2-6. A Align with etched line B Press chassis against clips C Slide into position READY LAN
.A
.B FIGURE 2-6 Placing the Aruba 52 into the Cradle A B C Align the front edge of the chassis with the etched line on the mounting cradle. This will fit the Aruba 52 mounting slots over the matching cradle posts. Press and hold the Aruba 52 chassis against the retaining clips on the cradle. Slide the Aruba 52 into place. When properly positioned, the retaining clips will spring up to hold the chassis firmly in place. NOTETo remove the Aruba 52 from the cradle, press down on both retaining clips and slide the chassis free of the mounting posts. 3 Secure the Aruba 52, if desired. To prevent the unauthorized removal of the Aruba 52 from its installed location, use a Kens-
ington MicroSaver Security Cable (not included). Wrap the security cable around an immov-
able object, insert the cables lock into the Kensington Security Slot on the back of the Aruba 52, and turn the key. 4 Orient the antennas. For best performance, swivel the antennas so that they are oriented vertically (see Figure 2-2 on page 18). Once mounting is complete, connect the required cables (see instructions on page 25). 22 Aruba 52 Installation Guide Part 0500007B August 2003 7/29/03 FINAL DRAFTCONFIDENTIAL Suspended Ceiling Mount Place the Aruba 52 into the mounting cradle as shown in Figure 2-6 on page 22. Use the T-rail clips, nylon washers, and nuts included in the optional mounting kit to attach the Aruba 52 to the underside of a suspended ceiling. 1 2 R E A D Y L A N
.A
.B Side View T-Rail Clip Cradle Washers Nut FIGURE 2-7 Mounting on a Suspended Ceiling The T-rail clips twist onto the rails used with standard suspended-ceiling systems. Place the T-rail clips approximately 15 cm (6 inches) apart at the location where the Aruba 52 will be installed. Use the mounting cradle to gauge the appropriate distance between the clips. Use the nylon washers to insolate the cradle from electrical contact with the T-rail. Make sure to insert the raised ridge of the lower washers fully into the cradle mounting holes as shown above. 3 Orient the antennas. For best performance, swivel the antennas so that they are oriented vertically (see Figure 2-2 on page 18). Once mounting is complete, connect the required cables (see instructions on page 25). Setup & Installation 23 Chapter 2 7/29/03 FINAL DRAFTCONFIDENTIAL Connect Required Cables The cables required for operating the Aruba 52 depend on your intended network topology
(see Figure 2-1 on page 8) and on the physical location. Direct SPOE to the Aruba WLAN Switch Use this procedure when connecting the Aruba 52 directly to an SPOE-compatible network port on the Aruba WLAN Switch (see Power Over Ethernet on page 2). SPOE provides 10/100 Mbps Ethernet, serial connection, and power over one cable. NOTEIf connecting the Aruba 52 through the LAN or to a non-SPOE network port on the Aruba WLAN Switch, see the instructions on page 26. 1 Connect the SPOE adapter to the Aruba 52. A Connect the adapters 9-pin serial connector to the Console port on the back of the Aruba 52. B Connect the adapters male RJ-45 plug to the FE port on the back of the Aruba 52. 2 Connect the Aruba 52 to the Aruba WLAN Switch. The connection between the Aruba 52 and the Aruba WLAN Switch requires an 8-conduc-
tor, Category 5 UTP, straight-through FE cable with RJ-45 connectors (see Appendix A for port specifications). Any FE cable installed in an air-handling space, as described in NEC (2002) Article 300.22(C), should be suitable under NEC Article 800.50 and marked accordingly for use in plenums and air-handling spaces with regard to smoke propagation, such as CL2-P, CL3-P, MPP or CMP. Install cables in accordance with all applicable local regulations and practices. A B Connect one end of the FE cable directly to the RJ-45 socket on the SPOE adapter that was attached to the Aruba 52 in the previous step. Connect the other end of the FE cable directly to an available SPOE network port on the Aruba WLAN Switch. NOTEThe Aruba 52 must be connected to the Aruba WLAN Switch without any inter-
vening hubs, routers, or other networking equipment. 24 Aruba 52 Installation Guide Part 0500007B August 2003 7/29/03 FINAL DRAFTCONFIDENTIAL CAUTIONTo prevent personal injury or damage to equipment, be sure to com-
ply with electrical grounding standards during all phases of installation and operation of the AP. Do not allow theAruba 52 to contact metal which is connected a different electrical ground than the Aruba WLAN Switch. Also, never connect the AP or WLAN switch to external storm grounding sources. LAN or POE Connection Use this procedure when connecting the Aruba 52 through the LAN or to a non-SPOE net-
work port on theAruba WLAN Switch. NOTEIf connecting the Aruba 52 directly to a SPOE network port on the Aruba WLAN Switch, see the instructions on page 25. 1 Connect the Aruba 52 to the network. A Connect one end of an FE cable to a network hub, router, or switch that has a routable path to the Aruba WLAN Switch.
If the connecting device supports POE (see Power Over Ethernet on page 2), use an 8- or 4-conductor, Category 5 UTP, straight-through FE cable.
If the connecting device does not support POE, use a 4- or 8-conductor, Category 5 UTP, straight-through or crossover FE cable. Any FE cable installed in an air-handling space, as described in NEC (2002) Article 300.22(C), should be suitable under NEC Article 800.50 and marked for use in plenums and air-handling spaces with regard to smoke propagation, such as CL2-P, CL3-P, MPP or CMP. Install cables in accordance with all applicable local regulations and practices. For port and cable details, see Appendix A. Connect the other end of the FE cable to the FE port on the back of the Aruba 52. B Setup & Installation 25 Chapter 2 7/29/03 FINAL DRAFTCONFIDENTIAL 2 Connect power. CAUTIONBe sure to comply with electrical grounding standards during all phases of installation and operation of the AP. Do not allow the Aruba 52 or power adapter (if used) to be connected to or make contact with metal or power outlets on a different electrical ground than the device to which it is connected. Also, never con-
nect the AP to external storm grounding sources. The Aruba 52 can receive electrical power using the following options:
POEIf connecting the Aruba 52 to a device that supplies IEEE 802.3af compliant POE
(see Power Over Ethernet on page 2), no additional power connection is necessary.
Power Outlet NOTEWhen the Aruba 52 is installed in an air-handling space, as described in NEC
(2002) Article 300.22(C), POE must be used instead of a power outlet. If local regulations and practices permit, connect the included AC power adapter cable to the DC power socket on the rear panel of the Aruba 52 and plug it into an appropriate power outlet. CAUTIONUse only the AC power adapter supplied with this device. Other-
wise, the product may be damaged. Reviewers:
Is shared secret config implemented?
26 Aruba 52 Installation Guide Part 0500007B August 2003 7/29/03 FINAL DRAFTCONFIDENTIAL Setup & Installation 27 Chapter 2 7/29/03 FINAL DRAFTCONFIDENTIAL 28 Aruba 52 Installation Guide Part 0500007B August 2003 7/29/03 FINAL DRAFTCONFIDENTIAL 7/29/03 FINAL DRAFTCONFIDENTIAL APPENDIX A Port Specifications Console Port The console port is located on the back of the Aruba 52 and has a DB-9 female connector. Port pin-outs are shown in Figure A-1:
Aruba 52 Console DB-9 Female DCE Pin-Out 9 8 7 6 5 4 3 2 1 SG TxD RxD Direction Input Output Figure A-1 Aruba 52 Console Port Communication settings for the console port are specified in Table A-1:
Table A-1 Console Terminal Settings Baud Rate Data Bits 9600 8 Parity None Stop Bits Flow Control 1 None Port Specifications 29 Appendix A 7/29/03 FINAL DRAFTCONFIDENTIAL FE Port The 10/100 Mbps Ethernet (FE) port is located on the back of the Aruba 52 and has an RJ-45 female connector. Port pin-outs are shown in Figure A-2:
Aruba 50 10/100 Mbps Ethernet RJ-45 Female Pin-Out 1 2 3 4 5 6 7 8 Direction Input Output Rx+ (POE negative*) Rx (POE negative*) Tx+ (POE positive*) Tx (POE positive*)
*POE optional Figure A-2 Aruba 52 FE Port The port accepts a 4- or 8-conductor Category 5 UTP FE cable with an RJ-45 male connector. The FE port detects MDI/MDX and automatically adjusts for straight-through or crossover cables. However, if Power Over Ethernet (POE) is used, a straight-through cable is required. The maximum length for FE cables is 100 meters (325 feet). When the Aruba 52 is installed in an air-handling space, as described in NEC (2002) Article 300.22(C), POE is required. Also, any FE cable installed in such spaces should be suitable under NEC Article 800.50 and marked accordingly for use in plenums and air-handling spaces with regard to smoke propagation, such as CL2-P, CL3-P, MPP or CMP. Install cables in accordance with all applicable local regulations and practices. 30 Aruba 52 Installation Guide Part 0500007B August 2003 7/29/03 FINAL DRAFTCONFIDENTIAL SPOE Adapter The Serial & Power Over Ethernet (SPOE) adapter pin-outs are shown in Figure A-3:
SPOE Adapter RJ-45 Female Pin-Out 1 2 3 4 5 6 7 8 ETH Rx+
ETH Rx ETH Tx+
Serial TxD Serial TGND ETH Tx Serial RxD Serial RGND
(POE negative)
(POE negative)
(POE positive)
(POE positive) Direction Input Output RJ-45 Male to Aruba 50 10/100 Mbps Ethernet Port DB-9 Male to Aruba 50 Console Port Figure A-3 Aruba SPOE Adapter The adapter requires an 8-conductor Category 5 UTP, straight-through FE cable with RJ-45 male connectors. The cable must connect the SPOE adapter to an FE+SPOE port on the Aruba WLAN Switch, with no intervening hubs, routers, or other network equipment. The maximum length for FE cables is 100 meters (325 feet). The Aruba 52 and SPOE adapter are plenum rated. When is installed in an air-handling space, as described in NEC (2002) Article 300.22(C), the connecting FE cable should be suit-
able under NEC Article 800.50 and marked accordingly for use in plenums and air-handling spaces with regard to smoke propagation, such as CL2-P, CL3-P, MPP or CMP. Install cables in accordance with all applicable local regulations and practices. Port Specifications 31 Appendix A 7/29/03 FINAL DRAFTCONFIDENTIAL 32 Aruba 52 Installation Guide Part 0500007B August 2003 7/29/03 FINAL DRAFTCONFIDENTIAL APPENDIX B Product Specifications The following specifications apply to the Aruba 52 Wireless Access Point (model WAP-50). Physical TABLE B-1 Physical Specifications Item Size Weight Measurement 20.5 x 13.6 x 4 cm
(8.07 x 5.35 x 1.58 in) 280 gram (9.9 oz.) Environment TABLE B-2 Environmental Specifications Item Temperature Humidity Measurement Operating: 0 to 50 C (32 to 122 F) Storage: 0 to 70 C (32 to 158 F) 5% to 95% (non-condensing) Product Specifications 33 Appendix B 7/29/03 FINAL DRAFTCONFIDENTIAL Operation General TABLE B-3 Operational Specifications Item Maximum Channels Maximum Clients Data Rate Operating Frequency Measurement 802.11aUS & Canada: 13, Japan: 5 802.11b/gUS & Canada: 1-11, Europe: 1-13, France: 10-13, Japan: 1-14, Spain: 10-11 64 802.11a6, 9, 12, 18, 24, 36, 48, 54 Mbps per channel 802.11b1, 2, 5.5, 11 Mbps per channel 802.11g6, 9, 12, 18, 24, 36, 48, 54 Mbps per channel 802.11a 5.15 ~ 5.25 GHz (lower band) US/Canada, Japan 5.25 ~ 5.35 GHz (middle band) US/Canada 5.725 ~ 5.825 GHz (upper band) US/Canada 802.11b/g 2.412 ~ 2.452 GHz US/Canada, Japan 2.457 ~ 2.462 GHz US/Canada, Europe, France, Japan, Spain 2.467 ~ 2.472 GHz Europe, France, Japan 2.484 GHz Japan Output Power Power 100 mW maximum (or lower as configured on the Aruba WLAN Switch to comply with local regulatory requirements) Adapter Input 100-240 AC, 50-60 Hz Access Point Input 3.3 VDC, 3 A (AC adapter), or 48 VDC, 150 mA (POE) LED Indicators Standards Ready (Power), LAN (Ethernet Link/Activity), .A and .B/.G
(Access Point/Air Monitor Mode) IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.11a/b/g, IEEE 802.3af 34 Aruba 52 Installation Guide Part 0500007B August 2003 7/29/03 FINAL DRAFTCONFIDENTIAL Certifications TABLE B-4 Certifications Item Electromagnetic Compatibility Measurement FCC Part 15 Class B, FCC Part 15 Class C 15.207/15.247, FCC Part 15 Class E 15.407 ICES-003, RSS 210 (CAN) IEC 61000-4-2/3/4/6/11 EN 55022, EN55024 (89/336/EEC), ETS 300 328 (89/336/EEC), ETS 301 489 (89/336/EEC), ETS 301 893 AS/NZS 3548, RFS 29 (NZ) CSA/NTRL (CSA 22.2 No. 950 & UL 1950) EN60950 (TV/GS), IEC60950 (CB), UL 2043 Safety Product Specifications 35 Appendix B 7/29/03 FINAL DRAFTCONFIDENTIAL 36 Aruba 52 Installation Guide Part 0500007B August 2003
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2003-10-07 | 2412 ~ 2462 | DTS - Digital Transmission System | Original Equipment |
2 | 5725 ~ 5825 | NII - Unlicensed National Information Infrastructure TX |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 2 | Effective |
2003-10-07
|
||||
1 2 | Applicant's complete, legal business name |
Hewlett Packard Enterprise Company
|
||||
1 2 | FCC Registration Number (FRN) |
0026486175
|
||||
1 2 | Physical Address |
3333 Scott Blvd
|
||||
1 2 |
Santa Clara, California 94089
|
|||||
1 2 |
United States
|
|||||
app s | TCB Information | |||||
1 2 | TCB Application Email Address |
h******@AmericanTCB.com
|
||||
1 2 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 2 | Grantee Code |
Q9D
|
||||
1 2 | Equipment Product Code |
ARUBA52
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 2 | Name |
R******** H********
|
||||
1 2 | Title |
Compliance Manager
|
||||
1 2 | Telephone Number |
650-2********
|
||||
1 2 | Fax Number |
408-2********
|
||||
1 2 |
r******@hpe.com
|
|||||
app s | Technical Contact | |||||
1 2 | Firm Name |
Elliott Laboratories Inc.
|
||||
1 2 | Name |
J**** M******
|
||||
1 2 | Physical Address |
684 West Maude Ave.
|
||||
1 2 |
Sunnyvale, California 94085
|
|||||
1 2 |
United States
|
|||||
1 2 | Telephone Number |
408-2******** Extension:
|
||||
1 2 | Fax Number |
408-2********
|
||||
1 2 |
d******@elliottlabs.com
|
|||||
app s | Non Technical Contact | |||||
1 2 | Firm Name |
Elliott Laboratories Inc.
|
||||
1 2 | Name |
J**** M********
|
||||
1 2 | Physical Address |
684 West Maude Ave.
|
||||
1 2 |
Sunnyvale, California 94085
|
|||||
1 2 |
United States
|
|||||
1 2 | Telephone Number |
408-2******** Extension:
|
||||
1 2 | Fax Number |
408-2********
|
||||
1 2 |
d******@elliottlabs.com
|
|||||
app s | Confidentiality (long or short term) | |||||
1 2 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 2 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 2 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 2 | Equipment Class | DTS - Digital Transmission System | ||||
1 2 | NII - Unlicensed National Information Infrastructure TX | |||||
1 2 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | WLAN Dual Band Access Point | ||||
1 2 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 2 | Modular Equipment Type | Does not apply | ||||
1 2 | Purpose / Application is for | Original Equipment | ||||
1 2 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | Yes | ||||
1 2 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 2 | Grant Comments | Power output listed is conducted. This Access Point is authorized for use only with the MINI PCI cards specified in the filing. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. | ||||
1 2 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 2 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 2 | Firm Name |
Elliott Laboratories LLC
|
||||
1 2 | Name |
D****** B********
|
||||
1 2 | Telephone Number |
408-2********
|
||||
1 2 | Fax Number |
408-2********
|
||||
1 2 |
d******@elliottlabs.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | CC CE | 2412.00000000 | 2462.00000000 | 0.0890000 | |||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
2 | 1 | 15E | CC CE | 5150 | 5350 | 0.032 | |||||||||||||||||||||||||||||||||||
2 | 2 | 15E | CC CE | 5725 | 5825 | 0.043 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC