| all | frequencies |
|
exhibits | applications |
|---|---|---|---|---|
| manual |
| app s | submitted / available | |||||||
|---|---|---|---|---|---|---|---|---|
| 1 |
|
Users Manual | Users Manual | 1.25 MiB | ||||
| 1 | Cover Letter(s) | |||||||
| 1 | External Photos | |||||||
| 1 | ID Label/Location Info | native | ||||||
| 1 | ID Label/Location Info | |||||||
| 1 | Internal Photos | |||||||
| 1 | Cover Letter(s) | |||||||
| 1 | Test Report | |||||||
| 1 | Test Setup Photos |
| 1 | Users Manual | Users Manual | 1.25 MiB |
ENTRYPROX 4045-907 (Rev A) S GUIDE HID Corporation 9292 Jeronimo Road Irvine, California 92618 USA Tel 949.598.1600 800.237.7769 Fax 949.598.1690 www.HIDCorp.com ii ENTRYPROX 4045-907 REV A iii Introduction .............................................1 Product Overview ...................................2 Unit Capacity.........................................................2 Transactions .........................................................2 Specifications........................................................3 Default Settings.....................................................4 Installing Entryprox.................................4 Assembly Parts.....................................................4 Mounting the Entryprox Unit..................................6 Wiring the Controller Keypad for a Standard Installation .............................................8 Wiring the Controller Keypad for a Secure Installation ................................................9 UL 294 Compliance Requirements .....................14 Wiring Entryprox ...................................17 Wiring the Main Relay.........................................18 Wiring the Auxiliary Relay ...................................18 Wiring the Request to Exit Input..........................23 Programming Entryprox.......................26 Card/PIN Programming.......................................30 Changing Operating Parameters ........................34 Wiegand Mode....................................................37 Program Command Table...................................38 LED/Sounder Status ...........................................45 Appendix A ............................................47 Addendum 4045C..48 HID CORPORATION iv ENTRYPROX 4045-907 REV A 1 INTRODUCTION This EntryProx Users Guide provides basic information and instructions for installing, wiring, and programming the EntryProx unit. IMPORTANT YOU MUST KEEP A USER LIST when programming cards and PIN codes into your EntryProx. Write down the User Location, Card Number, PIN Code and the Name of the User. Use the blank form in Appendix A as a photocopy master. DO NOT PROGRAM A CARD OR PIN IN USER LOCATION 1 for normal access control use. User Location 1 is reserved for the MASTER CODE, which places the unit into programming mode. CHANGE THE MASTER CODE from the factory default, after initial programming, and write this code down and keep it in a safe place. IF YOU LOSE OR FORGET THE MASTER CODE: End Users: contact your dealer a service call is required. Dealers: call HID Technical Support. CONSIDER A SECURE INSTALLATION if installing on an exterior door or high-risk location. FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. The reader is intended to be powered from a limited power source output of a previously certified power supply. UL 294 COMPLIANCE The EntryProx Unit complies with UL 294 Standard for Access Control Units in a standard wall-mount installation, only when installed in strict accordance with UL requirements. Please refer to page 14 for details. HID CORPORATION 2 PRODUCT OVERVIEW The EntryProx unit provides card and keypad access control for a single entrance. The unit can be installed in a standard one-stage configuration or a secure two-stage (remote) configuration. (Secure installation will be card-only.) To gain access to the controlled door, the user presents their card to the reader and / or enters their PIN code into the keypad. The unit searches its memory for that card or PIN code. If the unit finds the card or PIN code, it unlocks the door or performs some other action that has been programmed for that user. The EntryProx unit is compatible with all HID proximity access cards or key tags encoded with up to 37 bits of data. All programming options are performed using the controller keypad. Manual or batch card/tag programming via the keypad can be completed for 26-bit format only. A batch of cards or tags encoded in any format can be sequentially presented to the reader by entering a single keypad command. UNIT CAPACITY The EntryProx unit can accommodate up to 2,000 users. Each user is assigned to a User Location (numbered 1 2000), which can have a card/keytag, a PIN code, or a card/keytag PLUS a PIN code. User Location 1 is reserved for the Master Code (used for programming, only). TRANSACTIONS A maximum of 1,000 transactions can be stored in the EntryProx unit. Each transaction includes the time, the date, the User Location and the event. When maximum capacity is reached, the oldest transactions are overwritten. ENTRYPROX 4045-907 REV A 3 PRE-PROGRAMMING THE UNIT BEFORE INSTALLATION Dealers and installers are advised to pre-program the unit at their offices before installing it at the site. Simply connect it to a 12VDC source, follow configuration and card enrollment instructions at the end of this guide, and disconnect the unit. Programming will be retained in memory. You will spend less time at the site, and by being familiar with programming, will be able to train the end user more effectively. SPECIFICATIONS TABLE 1 - SPECIFICATIONS CATEGORY Environmental Operating Temperature Operating Humidity 31F to +150F
(-35C to +66C) @ 30 VDC 5% to 95% relative humidity, non-condensing REQUIREMENTS Electrical Power Supply/Current Requirements 10 - 15V DC, linear, filtered and regulated power supply recommended 150 mA for the EntryProx unit only. Additional capacity required for locking device or peripherals. Mechanical Height Width Depth Relay Outputs Main Relay, Aux Relay Form C (switches up to 1A inductive 5.25 in (13.3 cm) 2.75 in (7 cm) 1.625 in (4.1 cm) load, 2A resistive @ 30VDC) 4000 Hz, defeatable Bi-Color (red/green) Amber Infrared Sounder LEDs HID CORPORATION 10 seconds Infrared (IR) port DEFAULT SETTING 5 seconds ON 30 seconds 4 DEFAULT SETTINGS The EntryProx unit is shipped with the following default settings. PARA PARAMETER Master Code (User Location 1) 1234*
Main Relay energizes for Audible Keypress Feedback Local Propped Door Sounder activates after Local Forced Door Sounder activates immediately for Printer Output Port METER DEFAULT SETTING INSTALLING ENTRYPROX You can install the EntryProx unit by using a standard installation method or a secure installation method. Both installation methods require that you mount the EntryProx unit to a wall or glass surface. ASSEMBLY PARTS Before you install the EntryProx, be sure that you have the correct factory and installer supplied parts. A. Controller Keypad Unit B. Controller Keypad Backplate C. Cable Assemblies D. Antenna Backplate E. Antenna Housing F. Blank Label G. Mounting Screws I. Silicone Rubber Cushion J. Self-Adhering Pads K. 2-pin Jumper L. Filler Piece M. Lithium Coin Cell Battery (see warning below)*
N. Cover screws hex and tamper.*
O. Hex wrench*
H. Press to Exit Label
* - not shown in Figure 1 ENTRYPROX 4045-907 REV A 5 A B FIGURE 1: FACTORY SUPPLIED PARTS H F G K J I L D E C INSTALLER SUPPLIED PARTS LIST Appropriate DC power supply (10-15VDC, linear type) Appropriate electrical tools Recommended remote antenna cable ALPHA 1294C
(22AWG) Wiegand interface cable ALPHA 1295C (22AWG) (only if using a separate Wiegand access control panel) Power supply cable (18AWG - 22AWG) Door lock cable (18AWG - 22AWG) Door monitor cable (18AWG - 22AWG) Request to Exit cable (ALPHA 2421C 18AWG or ALPHA 1292C 22AWG) (only if using remote switch) Optional tamper screw bit (only if tamper screw is used Ademco 945T or PR-20451 magnet and reed switch or equivalent (for UL 294 compliance) CAUTION Replace Battery with Panasonic BR1225 only. Use of another battery may present a risk of fire or explosion. if mistreated. Battery may explode Do not recharge, disassemble or dispose of battery in fire. HID CORPORATION 6 MOUNTING THE ENTRYPROX UNIT If you mount the EntryProx unit to a wall, you can install an electrical junction box to hold the unit and the wires in place. The mounting hole cutouts on the backplate line up with the screw holes on a standard junction box. If you mount the EntryProx unit to a glass surface DO NOT remove the wire exits on the backplate. Remove the appropriate wire exit cutouts located on each side of the controller keypad case. If your installation must comply with the UL 294 Standard for Access Control, please read Page 14. PRECAUTIONS FOR OUTDOOR INSTALLATIONS Water damage is a key cause of unit malfunction, causing corrosion or short circuits. When mounting the unit in an area that will be exposed to rain or moisture, take the following precautionary measures:
1. Use silicone to seal wire runs and mounting holes
(antenna is already sealed). 2. Do NOT seal the cover and base together. Water that enters the case must be allowed to run out at the bottom. 3. Bend the wires to form a drip loop before they enter the case. This will prevent water from following the wires into the case. BEGINNING ENTRYPROX INSTALLATION To mount the EntryProx unit, refer to Figures 2 and 3 and follow these instructions:
1. Remove the hex screw located at the bottom of the EntryProx unit. 2. Disconnect the backplate of the EntryProx unit from the controller keypad. ENTRYPROX 4045-907 REV A 7 3. Remove the wire exits and mounting hole cutouts from the backplate as shown in Fig. 2. 4. Pull the wires through the backplate as shown in Figure 3. 5. Attach the backplate to a wall or glass surface using the mounting screws or the self-adhesive fasteners. Wire Exits FIGURE 2: REMOVING THE WIRING EXITS AND MOUNTING HOLES FIGURE 3: PULLING THE WIRES THROUGH THE BACKPLATE Mounting Hole Cutouts Mounting Hole Cutouts HID CORPORATION 8 WIRING THE CONTROLLER KEYPAD FOR A STANDARD INSTALLATION In a standard installation, the antenna housing remains installed in the controller keypad, and the complete unit is installed outside of the secured area. This is appropriate for interior doors or low-risk exterior installations. For compliance with the UL294 Standard, additional installation requirements must be met see page 14. To wire the EntryProx unit for a standard installation, refer to Figure 4 and follow these instructions. 1. Touch a grounded object BEFORE touching the main circuit board to guard against possible static discharges. 2. Remove the main circuit board by pushing outward on the two spring tabs in the direction shown in Figure 4. 3. Lift the main circuit board. 4. Make the wiring connections for the door locking devices, the power supply, and the alarm inputs and outputs. Refer to the Wiring EntryProx section for appropriate wiring diagrams. 5. Reattach the main circuit board to the controller keypad unit. 6. Attach the controller keypad unit to the mounted backplate and secure the EntryProx unit with a hex screw or tamper screw. Note: A ribbon cable holds the main circuit board to the controller keypad board. DO NOT CUT OR REMOVE this cable from its connector. ENTRYPROX 4045-907 REV A 9 FIGURE 4: REMOVING THE CIRCUIT BOARD WIRING THE CONTROLLER KEYPAD FOR A SECURE INSTALLATION In a secure installation, the waterproof antenna housing is removed from the controller keypad and mounted outside of a secured area. The control unit is installed inside the secured area. The blank filler piece is then inserted into the controller keypad in its place. This is appropriate for exterior doors or high-risk locations. To wire the EntryProx unit for a secure installation, refer to Figures 5 and 6 and follow these instructions. 1. Touch a grounded object BEFORE touching the main circuit board to guard against possible static discharges. HID CORPORATION 10 2. Remove the main circuit board by pushing outward on the two spring tabs in the direction shown in Figure 4. 3. Lift the main circuit board. 4. Unplug the four-pin cable assembly from connector P4 on the main circuit board. 5. Release the antenna housing from the controller keypad by pressing inward on the four securing tabs. 6. Remove the antenna housing from the controller keypad by pushing forward as shown in Figure 6. 7. Insert the extra 10-inch antenna cable assembly into connector P4. 8. Splice in additional antenna cable Alpha 1174C
(22AWG) up to a maximum of 10 feet. Note: The Alpha 1174C antenna cable is not supplied with the EntryProx unit. 9. Make the wiring connections for the Request to Exit switch, the door locking devices, the power supply, and the alarm inputs and outputs. Refer to the Wiring EntryProx section for appropriate wiring diagrams and instructions. 10. Reattach the main circuit board to the controller keypad unit. 11. Insert the blank filler piece into the controller keypad unit. 12. Attach the controller keypad unit to the mounted backplate and secure the EntryProx unit with a hex screw or tamper screw. 13. Run the additional antenna cable to the antenna housing location. 14. Mount and wire the antenna housing ENTRYPROX 4045-907 REV A 11 P4 Connector Cable Assembly FIGURE 5: REMOVING THE P4 CONNECTOR FIGURE 6: REMOVING THE ANTENNA HOUSING HID CORPORATION 12 MOUNTING AND WIRING THE ANTENNA HOUSING FOR A SECURE INSTALLATION Mount and wire the antenna housing no more than 10 feet away from the controller keypad unit. To mount and wire the antenna housing, refer to Figures 7 and 8 and follow these instructions. 1. Pull the additional antenna cable through the antenna housings backplate cable holes. FIGURE 7: MOUNTING THE ANTENNA BACKPLATE Cable Holes Moisture Release Holes 2. Position and secure the antenna backplate to the mounting surface so that the two moisture release holes are on the bottom. 3. Cut the plastic connector off the antenna cable assembly. 4. Splice in the additional antenna cable. Be careful to match the wire colors to the proper pin connectors on the 10-inch antenna cable assembly. 5. Attach the antenna housing to the backplate by inserting the four securing tabs into the backplate. 6. Seal the wire holes with silicone. ENTRYPROX 4045-907 REV A SELECTING A FILLER OR REQUEST TO EXIT LABEL The filler piece replaces the antenna housing on the controller keypad when you use the high security installation. If you do not plan to use the filler piece as a Request to Exit switch:
13 1. Insert the filler piece into the opening on the controller keypad. 2. Apply the blank label. FIGURE 8: ATTACHING THE ANTENNA HOUSING If you plan to use the filler piece as a Request to Exit switch:
1. Remove the two plastic side tabs on the filler piece. 2. Insert the silicone rubber cushion over the two alignment pins on the switch activator. 3. Apply the Press to Exit label to the filler piece. 4. Insert the filler piece into the opening on the controller keypad. 5. Refer to Figure 15 to make the wiring connections to the cable assembly if you are using a door contact. 6. Set the internal Request to Exit button ON, using programming Command 30, option 7 (see Table 2). HID CORPORATION 14 FIGURE 9: USING THE FILLER PIECE AS A REQUEST TO EXIT SWITCH Side Tab Cushion INSTALLATION REQUIREMENTS FOR UL 294 COMPLIANCE The EntryProx Model 4045AGU00 complies with the UL294 Standard for access control units in a standard, wall-mount installation, when installed to the following specifications:
Electric locking mechanisms may only be connected to the NO contacts of the Main Relay. Locking devices requiring an NC connection may only be used in conjunction with an interposing relay mounted inside the secure area and connected to the NO contacts of the Main Relay. The recommended or equivalent shielded wiring must be used for the following applications:
ENTRYPROX 4045-907 REV A 15 Request to Exit input cable Wiegand data output cable Alpha 1295C (22AWG) Alpha 1294C (22AWG) Antenna cable extension Alpha 1292C (22AWG) or 2421C (18AWG) The cable shield drain wires must be grounded at the reader end by connection to P1, Pin 4 (DC Power Ground) using appropriate wire nuts or crimp fittings. Tamper Switch must be installed in one of the configurations recommended below, and connected to an intrusion alarm system. (Refer to Figure 10 for switch/magnet locations) MOUNTING OVER A METAL OR PLASTIC SINGLE GANG J-BOX 1. Use an Ademco 945T magnet and reed switch (or equivalent) with foam-backed adhesive tape. 2. Clip the screw mounting tabs from both the magnet and reed switch using pliers or a wire cutter. 3. Remove the backing sheet from the tape on the magnet and stick the magnet to the plastic spacer, which is factory-installed to the back of the Keypad board in location A (Figure 10). 4. Stick the reed switch on the inside of the long side of the J-box in the upper right-hand corner, using the adhesive tape. The switch should be flush with the edge of the J-box. WALL MOUNTING 1. Use an Ademco PR-20451 magnet and reed switch
(or equivalent) with foam-backed adhesive tape. 2. Remove the backing sheet from the tape on the magnet and stick the tape to the plastic spacer, which is factory-installed to the back of the Keypad board at location B (Figure 10). HID CORPORATION 16 3. Drill a 3/8 inch hole in the wall behind the magnet location, feed the switch wire through the wall and press the switch into place. FIGURE 10 TAMPER SWITCH INSTALLATION Magnet B Magnet B Magnet A Magnet A Keypad Keypad Electronics Board Electronics Board Batt. Batt. Main Electronics Board Main Electronics Board NOTE: UNIT IS SHOWN FROM BACK WITH BASE REMOVED ENTRYPROX 4045-907 REV A 17 WIRING ENTRYPROX This section includes wiring diagrams for the following:
Wiring the main relay Wiring the auxiliary relay Wiring the Request to Exit switch Figure 10 illustrates the location and description of the four pin connectors on the main circuit board and its use. FIGURE 11: PIN LOCATOR DIAGRAM Blue Not Used Brown Wiegand LED Control White Wiegand Data 1 Green Wiegand Data 0 1 2 3 4 Red Power +12 VDC Black Ground Blue Main Relay COM Green Main Relay NO Gray Main Relay NC 5 4 3 2 1 HID CORPORATION 1 2 3 4 5 6 Green Aux Relay NO Gray Aux Relay NC Blue Aux Relay COM Brown Rex Loop Orange Door Loop White Loop Common*
* Note: Rex Loop requires NO switch; Door Loop requires NC switch. Connect commons from both loops to Loop Common input P2, Pin6, White. Red LED (Red +) Black LED (Green +) Antenna +
Antenna -
1 2 3 4 18 WIRING THE MAIN RELAY The main relay for the door locking device is wired to connector P1 on the EntryProx main circuit board. To connect a Fail-Secure Strike or Lock see Figure 12. To connect a Maglock or Fail-Safe Strike see Figure 13. WIRING A GATE ACTUATOR You can make the wire connections for a gate actuator by connecting the Blue (C) wire and the Green (N/O) wire directly to the input as shown in Figure 12. Note: DO NOT connect a power supply to the relay if you connect a gate actuator. WIRING THE AUXILIARY RELAY The EntryProx unit has an auxiliary relay feature that allows for customized alarm programming. Pins 1, 2, and 3 on the P2 connector can be wired for one of the following alarm outputs:
Alarm shunt (see Figure 14) Forced or propped door (see Figure 15) The alarm shunt operation allows you to use the auxiliary relay to bypass a door contact that is monitored by a separate alarm system. If the entry or exit is controlled by the EntryProx unit, an intrusion alarm will not be generated if the door is opened using an access card or PIN number, or by pressing the REX button. The forced or propped door alarm allows you to use the auxiliary relay to provide a local warning, such as an audible or visual indicator if:
A door is opened without using an access card or PIN number at the EntryProx unit. A door is legitimately opened but is held open too long. Note: The auxiliary relay audible and visual indicators and the door open times can be programmed. Refer to Table 2:
Programming Commands for more information. ENTRYPROX 4045-907 REV A 19 BLUE
(Main Relay C) RED
(V+ IN) V-
V+
(V-) BLACK GREEN STRIKE
(Fail Secure) Power Supply Linear type 12VDC FIGURE 12: ELECTRIC STRIKE (FAIL SECURE WIRING DIAGRAM)
(Main Relay NO) Strike can also be powered by a separate power supply;
consult strike installation manual for details. HID CORPORATION 20 FIGURE 13: MAGLOCK (FAIL SAFE WIRING DIAGRAM) MAG LOCK
(Fail Safe) V-
V+
Linear type 12VDC Power Supply BLACK
(V-) GRAY
(Main Relay NC) BLUE
(Main Relay C) RED
(V+ IN) Mag Lock can also be powered by a separate power supply;
consult Mag Lock installation manual for details. ENTRYPROX 4045-907 REV A FIGURE 14: WIRING AUXILIARY RELAY FOR ALARM SHUNT OPERATION 21 DOOR CONTACT
(Monitored by Alarm Panel) GREEN
(NO) BLUE
(C) ORANGE DOOR CONTACT
(Monitored by EntryProx Unit) WHITE HID CORPORATION 22 FIGURE 15: WIRING AUXILIARY RELAY FOR PROPPED/FORCED DOOR ALARM POWER SUPPLY V-
V+
BLUE
(C) ORANGE GREEN
(NO) DOOR CONTACT
(Monitored by EntryProx Unit) WHITE ENTRYPROX 4045-907 REV A 23 WIRING THE REQUEST TO EXIT INPUT When the EntryProx Request to Exit (REX) input receives a momentary switch closure, it engages the main relay for the programmed access time. It can be connected to a wall-
mounted exit button, to a push button under a reception desk, or to the relay output of a passive infrared motion detector mounted above the door on the secure side. The Request to Exit input activates the alarm shunt to prevent false alarms when personnel use the controlled door to exit the secured area. The Transaction Log records all Request to Exit usages for monitoring purposes. To wire the EntryProx Request to Exit input, refer to Figures 16 and 17. Locate connector P2 on the main circuit board and remove the 2-pin jumper installed on pins 5 and 6. Refer to Figure 17 to make the wiring connections to the cable assembly if you are NOT using a door contact Note: If you do not use a door contact, you need to twist the white and orange wires together or the REX input will not function. Note: The door contact must be closed for the Request to Exit feature to work properly HID CORPORATION 24 FIGURE 16: WIRING REQUEST TO EXIT INPUT (WITH DOOR CONTACT) NORMALLY OPEN SWITCH ORANGE BROWN WHITE DOOR CONTACT ENTRYPROX 4045-907 REV A FIGURE 17: WIRING REQUEST TO EXIT INPUT (NO DOOR CONTACT) 25 ORANGE BROWN WHITE NORMALLY OPEN SWITCH HID CORPORATION 26 PROGRAMMING ENTRYPROX IMPORTANT READ BEFORE PROGRAMMING THE ENTRYPROX UNIT YOU MUST KEEP A USER LIST when programming cards and PIN codes into your EntryProx. Write down the User Location, Card Number, PIN Code and the Name of the User. Use the blank form at the end of this book as a photocopy master. You will need this information if you need to delete a card or PIN at a later time. DO NOT PROGRAM A CARD OR PIN IN USER LOCATION 1 for normal access control use! User Location 1 is reserved for the MASTER CODE, which places the unit into programming mode. CHANGE THE MASTER CODE from the factory default, after initial programming, and write this code down and keep it in a safe place. IF YOU LOSE OR FORGET THE MASTER CODE:
End Users: contact your dealer a service call is required. Dealers: call HID for the procedure and remember to bring the proper hex key or security tool to the customer site!
PROGRAMMING COMMAND SEQUENCES Command sequences are simply a series of keypad entries to add cards and PINs or change operating characteristics of the EntryProx unit. There are three basic steps to programming EntryProx, using the Keypad on the control unit:
1-Place the unit in programming mode press 99 # Master Code *
2- Enter a Command Sequence press a 2-digit command number to enter cards/PINs or specify parameters by pressing keys in various sequences 3- Exit programming mode - press * to exit. ENTRYPROX 4045-907 REV A LED INDICATION DURING PROGRAM MODE A slow blinking yellow LED indicates that the unit is in program mode. When the yellow LED stops blinking and is OFF completely, the unit is no longer in program mode. A steady yellow LED indicates an error condition:
27 1- you are trying to enter a card or PIN which is already stored in another User Location 2- you have pressed the wrong key in a command sequence Press * to clear the error condition and then enter a new code or PIN, or re-enter the command sequence as required. If the unit does not go into program mode, contact your dealer or HID Technical Support. BEFORE YOU START Before programming cards, try to determine:
How many cards do I have to enroll? If you have more than 25 you may want to batch enroll them. If you have fewer, you may want to program one at a time. How are the cards encoded: What is the bit format, ID numbers and facility code? If you have sequentially numbered cards with 26-bit format and the same facility code, you can batch-enroll them from the keypad. Otherwise you must program them individually or batch-
enroll by sequentially placing the cards in front of the reader. Note that if you choose to add new cards manually (via the keypad), the facility code must be entered into the unit first. For the programming sequence used to enter the 3-digit facility code, see Table 2, item 32. HID CORPORATION 28 PIN CODE/CARD PROGRAMMING BASICS PIN codes and card numbers can be programmed manually via the keypad. Cards can also be programmed by presentation to the reader at the correct point in the command sequence. When adding or modifying PIN codes or cards the user enters a 2-digit Command, then specifies three or four data values: a user type, a location and a keypad-PIN, and/or card. USER LOCATIONS These are the locations in the units memory where Card and/or PIN User data is stored. EntryProx User Locations are numbered 1 2000. User Location 1 is reserved for the Master Code, used for programming Do not enter cards or PINs for normal access into User Location 1. USER TYPES User Types determine what happens when a user presents their card/PIN to the reader. A User Location can be programmed as one of four specific user types:
Toggle/latch strike (0) For this user-type, when the Card is presented (or PIN is entered) the door opens for an indefinite period, until the card / code is reentered or another toggle code is entered (this is useful for deliveries, for example). Normal access (1) This is the default user type, when the Card is presented (or PIN is entered) the door opens for the duration of the Main Relay time. log Dump (2) For this user-type, when the Card is presented (or PIN is entered) the door remains locked and the Transaction Log is dumped to an optional IR printer ENTRYPROX 4045-907 REV A via the IR LED. (There are three LEDs on the top of the unit - the IR LED is the one on the right.) This code cannot be used to gain access through the door. Note that the log is only printed, not erased. 29 Lockout (3) For this user-type, the keypad freezes, disallowing all other codes, plus the door remains in the current state. During a lockout state, card access does not continue to work. If it is locked, it remains locked. If it is unlocked, it remains unlocked until another Lockout code is entered, releasing it from Lockout mode. NOTE: Reserve this user-type for a supervisor or override function. PIN CODES, CARDS AND COMBINATIONS A User Location can be programmed with one of the four PIN code/card combinations listed below using the programming Commands in parentheses
(1) PIN Code ONLY (Command 50)
(2) PIN Code AND Card (Command 50 plus present card to proximity reader)
(3) Card ONLY (Command 50 or Command 51)
(4) PIN Code OR Card (Command 52) No User Location can have the same card and/or PIN code as another User Location. ENTERING USER PIN CODES EntryProx user PIN codes consist of a minimum of one digit and a maximum of six digits. Note that a leading 0 is considered a digit, and that the 5-digit code 12345 is different from the six-digit code 012345. Attempting to enter a user PIN code into memory that is already stored in a different user location causes the yellow LED to stop blinking and remain steadily lighted. If this occurs, try entering a different user code. Repeating digits in the same code is acceptable (ex:
121122). HID CORPORATION 30 CARD/PIN PROGRAMMING SEQUENCES Following are the most commonly used command sequences for programming user data into the EntryProx:
PROGRAMMING PIN + CARD To program a user for both Code AND Card:
1. Place the EntryProx unit in program mode. Press:
99 # Master Code * (default is 1234) 2. On the EntryProx keypad, press:
50 # user-type # user location # keypad PIN
* keypad PIN * <present card>
3.Press * to exit program mode. QUICK PROGRAMMING EITHER PINS OR CARDS A quick program feature allows user data entry with minimal keystrokes. No command number is required. This feature programs either a card or a PIN, not a combination, and it automatically selects a Normal user access type. Just enter the users location and the PIN (or present card):
1. Place the EntryProx unit in program mode. Press:
99 # Master Code * (default is 1234) 2. On the EntryProx keypad, press:
user location # PIN * PIN * OR user location # ** <present card>
3. Press * to exit program mode. PROGRAMMING PIN CODE ONLY USE To program PIN Code ONLY operation with Command 50 use the following program sequence:
1. Place the EntryProx unit in program mode. Press:
99 # Master Code * (default is 1234) 2. On the EntryProx keypad, press:
50 # user-type # user location # keypad PIN
* keypad PIN *
3. Press * to exit program mode. USER TYPES - REMINDER 0-Toggle 1-Normal 2-Dump 3-Lockout ENTRYPROX 4045-907 REV A PROGRAMMING CARD ONLY USE To program Card ONLY use with Command 50, simply omit the keypad PIN values from the sequence:
31 1. Place the EntryProx unit in program mode. Press:
99 # Master Code * (default is 1234) 2. On the EntryProx keypad, press:
50 # user-type # user location # **
<present card>
3. Press * to exit program mode. PROGRAMMING CODE OR CARD To program a user for either Code OR Card:
1. Place the EntryProx unit in program mode. Press:
99 # Master Code * (default is 1234) 2. On the EntryProx keypad, press:
52 # user-type # user location # keypad PIN
* keypad PIN * <present card>
3. Press * to exit program mode. BATCH LOAD CARDS BY KEYPAD ENTRY Command 56 allows you to batch load multiple, sequential 26-bit HID cards into the EntryProx unit. Up to 1,999 users can be added at one time. Cards need not be presented to the reader. Requirements are:
Cards must all have the same facility code. Cards must be sequentially numbered The facility code must be programmed into the unit before any batch loading. See Table 2, Command 32 for the procedure. (This facility code cannot be changed at a later time). Cards with multiple facility codes or many numbering gaps must be entered by presentation to the reader, using Command 53. USER TYPES - REMINDER 0-Toggle 1-Normal 2-Dump 3-Lockout HID CORPORATION 32 If the Batch Loading conditions can be met:
1. Place the EntryProx unit in program mode. Press:
99 # Master Code * (default is 1234) 2. On the EntryProx keypad, press:
56 # (total number of cards to be added) #
(starting user location) # card number *
repeat card number *
NOTE: Never enter one (1) as the starting user location since it is reserved for the master code. 3.Press * to exit program mode. BATCH LOAD BY PRESENTATION Use Command 53 to program a batch of cards into consecutive User Locations by specify the starting User Location, then presenting cards or tags to the reader. Use any card format up to 37 bits. All cards are programmed alike and users are card only. Card enrollment stops once the current user location exceeds 2000, or press any key to abort. Keep a written record as you program cards. Existing data in the User Locations being programmed is overwritten, unless you present a card that is already programmed into the EntryProx, in which case an error is generated. To clear the error, press the * key; then continue presenting cards. If you enter User Location 1 as the first card in the sequence, this will generate an error. To batch load by presentation, follow this procedure:
1. Place the EntryProx unit in program mode. Press:
99 # Master Code * (default is 1234) 2. On the EntryProx keypad, press:
53 # user type # start location # ** <present card> <present card>
<present card>
3. Press * to exit program mode. USER TYPES - REMINDER 0-Toggle 1-Normal 2-Dump 3-Lockout ENTRYPROX 4045-907 REV A DELETING USERS To delete a user from the EntryProx, you must know the User Location in which the information is stored. 33 1. Place the EntryProx unit in program mode. Press:
99 # Master Code * (default is 1234) 2. On the EntryProx keypad, press:
user location #**
3. Press * to exit program mode. BLOCK DELETE USERS Use Command 58 to delete all cards / PINs in a block of User Locations. The yellow LED will blink rapidly during the deletion process. It can take several seconds to delete large blocks of users. The following items will generate a programming error:
Entering a starting User Location of 1 or greater than 2000 Entering a total number of locations which exceeds 1999 Entering a starting user location and number of locations which exceeds 2000 To block delete user locations, follow these steps:
1. Place the EntryProx unit in program mode. Press:
99 # Master Code * (default is 1234) 2. On the EntryProx keypad, press:
58 # start location # start location # number of locations * number of locations*
3. Press * to exit program mode CHANGING THE MASTER CODE Use the Quick Program Feature to change the master code 1. Place the EntryProx unit in program mode. Press:
99 # Master Code * (default is 1234) 2. On the EntryProx keypad, press:
1 # (new code) * (repeat new code) *
3. Press * to exit program mode HID CORPORATION 34 CHANGING OPERATING PARAMETERS Many users will use the EntryProx with the factory default operating parameters. The following commands include some of the most commonly customized parameters. For further refinements on EntryProx operation, review the options shown in Table 2. CHANGING THE MAIN RELAY TIME The main relay time applies to all users 1-2000. The factory default main relay time is five (5) seconds. Main relay time can be set from one to ninety-nine seconds in one-second increments using Command 11. 1. Place the EntryProx unit in program mode. Press:
99 # Master Code * (default is 1234) 2. Enter the new main relay time, in seconds (from 1 to 99). For example, to enter 10 seconds, press:
11 # 10 # 0 # **
3. Press * to exit program mode. INVALID PIN LOCKOUT Command 30, Option 18 allows you to enable or disable the Invalid PIN Lockout (IPL) feature. This feature prevents unauthorized persons from gaining entry by guessing PIN codes or Master Codes. When a preset number of invalid entries is exceeded (set by using Command 32 option 4, default is 5) the EntryProx will either trigger the Forced Door output, or the keypad will be disabled for a user-configurable time period (select the action, using Command 30, option 19, and then set lockout time by using Command 32 5). The invalid PIN code count is reset to zero by any of the following:
entering a valid keypad PIN presenting a programmed Prox card entering a valid [ 99 # Master code* ] sequence the expiration of the keypad timer ENTRYPROX 4045-907 REV A 35 The Invalid PIN Lockout function disables all keypad PIN entries with the exception of the [ 99 # Master Code* ]
sequence for the duration of the lockout. To clear an active timed Invalid PIN Lockout:
disconnect power to the system present a valid prox card programmed as Card Only or Card OR Code Enter the [ 99 # Master Code * ] sequence Note that if an invalid [ 99# Master Code* ] is entered as part of the sequence to clear the IPL, a good [99# Master Code* ]
sequence will not cancel the current lockout. RESETTING THE MASTER CODE AND SYSTEM DEFAULTS ONLY Command 40 erases everything from the EntryProx memory except the user list and transaction log and restores the default settings. This is useful if the EntryProx unit has experienced programming problems, or if you wish to delete earlier programming. 1. Place the EntryProx unit in program mode. Press:
99 # Master Code * (default is 1234) 2. Press:
40 # 00000 # 00000 # **
3. Press * to exit program mode. ERASING ENTIRE MEMORY / RESETTING SYSTEM DEFAULTS Command 46 deletes everything from the EntryProx memory including the user list but not the transaction log and restores the default settings. This is used as a last resort if you need to erase a specific user and could not retrieve the Programmed User List. HID CORPORATION 36 1. Place the EntryProx unit in program mode. Press:
99 # Master Code * (default is 1234) 2. Press:
46 # 00000 # 00000 # **
3. Press * to exit program mode. TURNING KEYPRESS AUDIBLE FEEDBACK ON/OFF The Keypress Audible Feedback command enables the sounder to beep once for each key press. This feature provides an audible acknowledgment that a particular key was pressed hard enough for the unit to understand. The factory-
shipped default setting is ON, but it can be toggled ON and OFF as desired using command 30. 1. Place the EntryProx unit in program mode. Press:
99 # Master Code * (default is 1234) 2. To enable this feature, press:
30 # 0 # 1 # **
3. To disable this feature, press:
30 # 0 # 0 # **
4. Press * to exit program mode. TURNING KEYPRESS VISUAL FEEDBACK ON/OFF The keypress visual feedback feature lights the LED once for each key press. This feature provides a visual acknowledgment that a particular key was pressed hard enough for the unit to understand. The factory-shipped default setting is ON, but it can be toggled ON and OFF as desired. 1. Place the EntryProx unit in program mode. Press:
99 # Master Code * (default is 1234) 2. To enable this feature, press:
30 # 1 # 1 # **
3. To disable this feature, press:
30 # 1 # 0 # **
4. Press * to exit program mode. ENTRYPROX 4045-907 REV A 37 WIEGAND MODE If you program the EntryProx unit to operate in Wiegand mode with a separate access control panel, the following features are not accessible:
The EntryProx unit does not control door lock or unlocking operations. The EntryProx unit is not able to store codes in memory. The main and auxiliary relay functions are turned off. The door monitor and Request to Exit inputs are disabled. For more information on programming the EntryProx unit for Wiegand operation, please contact your local distributor. PIN CODE OUTPUT IN WIEGAND MODE The system transmits keypad PINs while operating in Wiegand mode by processing any digit sequence terminated with the [*] key as 26-bit Wiegand data. The current facility code (set using Code 32 - 2) will be used. Entering any PIN over 65535 will cause an error condition and no data will be sent. Because keypad data is sent in a card data format, it may not be possible for some panels to perform CARD AND CODE operation (requiring both) to gain access. If your panel cannot accept and interpret 26-bit format as PIN data, be sure to configure the user at the PC host software by entering the code into the CARD data field for that user, not the keypad PIN number field. HID CORPORATION 38 PROGRAMMING COMMAND TABLE Read the following table before completing programming of your EntryProx unit; it describes various programming commands and how to execute them. As with the previously described commands, you must first press 99 # (Master Code) * to enter programming mode, enter the desired command sequence, and then press * to exit programming mode. Ref number is for reference only, not to provide an ordered sequence of commands. TABLE 2: PROGRAMMING COMMANDS. TO... Ref 1 IF YOU WANT TO Enter program mode Change master code Code-only operations PRESS 99 # (Master Code) *
1 # (new code) *
(repeat code) *
2 3 4 Set main relay time 11 # tt # 0 # **
Set AUX relay output 15 # output mode
# 0 # **
5 Delete users User Location #
6 Print a transaction Log 70 # 0 # 0 # **
DETAILS yellow LED blinks slowly example; 4321 master code
(1 # 4321 *
4321 *) tt = 1 - 99 seconds Output Modes:
0 = disabled, 1 = shunt, 2 = forced door, 3 = propped door Example:
To delete user 100, press:
100#**
Hold optional printer with IR receiver near the EntryProx IR LED. ENTRYPROX 4045-907 REV A Ref 7 IF YOU WANT TO Set/clear standard option PRESS 30 # option # s/c
39 DETAILS See below for Option numbers and descriptions Set/Clear 0 = OFF/1 = ON 0 = OFF/1 = ON 0 = OFF/1 = ON
(Recommend OFF) 0 = standalone/1=Wiegand 0 = OFF/1 = ON 0 = OFF/ 1 = ON 0 = OFF/1 = ON 0 = OFF/1 = ON 0 = US/1 = European 0 = OFF/1 = ON 0 = LOW/1 = HIGH 0 = OFF/ 1 = ON 0 = LOW/1 = HIGH 0 = OFF/ 1 = ON 0 = OFF / 1= ON (prevents multiple card reads in Wiegand mode) 0 = OFF / 1= ON 0 = TIMED LOCKOUT / 1
= Forced Door Output ESS DETAILS Option Number/Description 0: Audio keypress feature 1: Visual keypress feature 2: Auto entry enable 3: Stand-alone/Wiegand operation 4: Facility code access (26-bit cards only) 5: Forced door audio alert 6: Propped door audio alert 7: Internal Request to Exit switch 8: US/EU date format 9: Wiegand red LED enable 10: Wiegand red LED active state 11: Wiegand green LED enable 12: Wiegand green LED active 13: Daylight saving time 14: Prox card antipassback select 18: Invalid PIN lockout select 19: Invalid PIN lockout action HID CORPORATION 40 Ref 8 IF YOU WANT TO Print programmed user list 9 Print programmed user list (starting at a certain user) 10 Change Wiegand parameters DETAILS 32 # parameter
# value # **
25 # 0 # start user # **
PRESS 25 # 0 # 0# ** Hold optional printer with IR receiver near the EntryProx IR LED. Hold optional printer with IR receiver near the EntryProx IR LED. Parameter/Value 0, Wiegand pulse count/1- 255 (8 -
160s) 1, Wiegand interpulse/1-255
(spacing 32 - 640s) 2, facility code/0-225
(default = 0) (26-bit cards only) 3, Process card timer 2 240 in second increments, defaults to 4 1 second. (If Option 30# 14# is enabled, this sets the time that a card must be removed from the RF field before it can be re-read.) 4, Invalid PIN lockout threshold 1 50 attempts (defaults to 5) 5, Invalid PIN lockout duration 1 255 in 5 second increments (defaults to 60 - 5 minutes) ENTRYPROX 4045-907 REV A Ref 11 IF YOU WANT TO Set system time 12 Set system date 13 14 15 Set door number Set propped door time (this sets delay time for both the Aux Relay and local sounder) Set forced door time (this sets active time for both the Aux Relay and local sounder) 16 Delete memory except user list and restore system defaults
(also see command 46) 17 Delete all memory and reset system defaults PRESS 41 # hhmm # 0
42 # mmddyy
# dow # **
43 # nnnn # 0
44 # ttt # 0 #
45 # ttt # 0 #
41 DETAILS hhmm =
hour/minute, 24-hr format mmddyy =
month, day, year;
dow = day of week, 1 = Sunday nnnn = door number
(for printed reports) ttt = propped door time, to nearest 10's seconds, entered as 10 -990; default =
30 seconds ttt = forced door time, to nearest 10's seconds, entered as 10 - 990; default =
10 seconds 40 # 00000 #
00000 # **
46 # 00000 #
00000 # **
HID CORPORATION 42 Ref 18 19 20 21 22 23 IF YOU WANT TO Program user:
Code ONLY NOTE: You can program the four types of users shown to the right Program user:
Code AND Card Program user:
Card ONLY Program card user manually: Card ONLY (26-bit cards ONLY) Program user:
Code OR Card Program a group of consecutive users by presenting cards PRESS 50 # user-type
# user location
# code * repeat code *
50 # user-type
# user location
# code * repeat code *
<present card>
50 # user-type
# user location
<present card>
51 # user-type
# user location
# card ID *
card ID *
52 # user-type
# user location
# code* repeat code *
<present card>
53 # user type
# start location
<present card>
<present card>
<present card>
DETAILS User Types:
0 - Toggle/latch strike 1 - Normal Access 2 - Log Dump 3 - Lockout the card ID appears on the card (facility code must be entered first; see 32 # 2 #
command) Programs card-only users. Stops at user location 2000, or press any key to abort. Erases existing prog-
ramming. If an exis-
ting card is presented, an error will occur press * to resume ENTRYPROX 4045-907 REV A PRESS 56 # total count #
starting user location #
starting card ID
* starting card ID *
58 # start user
# start user #
number of users * number of users *
43 DETAILS the card ID appears on the card; (facility code must be entered first; see 32 # 2 #
command) Yellow LED blinks rapidly; allow several seconds for large blocks of users. Cannot delete: master user, more than 1999 users, or user location greater than 2000. User Location
# * * <present card>
70 # 0 # 0 # ** Hold optional printer with IR receiver near the EntryProx IR LED. Prevent specified transactions from being logged. Set =1
(prevent) Clear = 2 (restore) See list below. 73 # event #
set/ clear # **
Ref 24 IF YOU WANT TO Perform batch entry of users:
Card ONLY (26-bit cards ONLY) 25 Block Delete Users 26 Quick Enroll Card 27 28 Print Transaction Log via IR port Set transaction log mask (set/clear event logging) NED ORS HID CORPORATION 44 IF YOU WANT TO 29 Reset transaction Log 30 To exit Program mode OUNDER Code Transaction Event 01 Access Denied 02 Program Denied 03 Program Mode 04 Request to Exit 05 Door Ajar 06 Door Closed 07 Forced Door 08 Log Erased 09 Facility Access 16 Print 17 Access 20 Toggle ON 21 Toggle OFF 24 Lockout ON 25 Lockout OFF 27 Mismatch PRESS 76 # 00000 #
00000 # **
* (after final command) DETAILS yellow LED stops flashing ENTRYPROX 4045-907 REV A LED/SOUNDER STATUS INDICATIONS TABLE 3 LED/SOUNDER INDICATIONS LED OR SOUNDER Yellow LED VISUAL/AUDIBLE CONDITION Slow blink DESCRIPTION 45 Unit is in Program mode Verify mode is active
(checking that the last two values in sequence match) Program error; to clear, press *
Memory (EEPROM) erase is in progress
(commands 40/46, 58 loop-back) Strike is locked Strike is energized
(timed or latched) Strike toggle is unlocked and user lockout active of ID during Card AND Code access attempt User lockout is active and strike locked; red LED drops out for 100 ms every second;
normal users cannot change the state of the relay. This also indicates Invalid Pin Lockout. Rapid blink Steady Very rapid blink Bi-Color LED Steady red Steady green Solid green with red flicker Red blink DE HID CORPORATION Red/green alternating Awaiting second form 46 LED OR SOUNDER Sounder VISUAL/AUDIBLE CONDITION Short beep (100 ms) every 2 seconds Sounder 1/2 second on, 1/2 second off 3 rapid beeps after code is entered or card is presented 3 slow beeps (250 ms), then a single beep 1 single beep DESCRIPTION Propped door is active Forced door is active Code or Card is not found Self-test is complete Valid card access ENTRYPROX 4045-907 REV A 47 Instructions: Do not write on this page - use it as a photocopy master. Copy the chart at a 200% enlargement. Make as many copies as required to record all programmed users, and write information in the appropriate spaces. Place the users charts in a binder, and keep them in a secure location. HID CORPORATION 48 Addendum to EntryProx Users Guide PN 4045-907 This addendum explains whats new in the EntryProx 4045 Rev C. The changes are:
1. Transaction History and User List downloads are no longer made via the Infrared LED to the optional HP Thermal Printer (4045-PRN). The Rev C model is compatible with the optional EntryProx DCD program, running on an optional Palm Zire 71 or Zire 72. 2. The unit now has an additional connector, P5, which provides an RS-485 interface for future applications. 3. No other functionality is changed. USING THE DOWNLOAD FEATURES The EntryProx unit can download a Transaction Log and a Programmed User List to an optional Palm Personal Digital Assistant (PDA) via the IR LED. There are three LEDs on the top of the EntryProx unit - the IR LED is the one on the right. USING THE DCD PROGRAM The Data Collection Device (DCD) Application is currently provided on a 16MB SD Card. Future versions will be loaded into the Palm from a PC. To obtain basic instructions on how to operate the Palm Zire 71 or 72, how to install the SD Card, and for the location of the Palm IR Receiver, refer to the Palm user documentation. ENTRYPROX 4045-907 REV A 49 1. Install the SD Card containing the DCD Application into the Palm Expansion Card Slot. 2. Touch the Data Collection icon on the PDA screen. 3. The program will start, displaying three menu options: Retrieve, Files, and Settings 4. Click on Settings to be sure the following parameters are selected:
a. Comm Method Ir Channel 2 b. Comm Speed 19200 c. Protocol Printer d. Timeout (Seconds) - 30 5. To download data from the EntryProx Unit to the Palm:
a. Place the Palm IR receiver within 1/2 of the b. Enter the required command sequence at the EntryProx IR LED EntryProx keypad c. Quickly touch Retrieve on the PDA screen. 6. Be sure to have the Palm and the EntryProx in position and ready before starting a download: if the Palm is not ready, the EntryProx may finish downloading data before the Palm is able to receive it;
or if the EntryProx is not ready, the Palm may time out before the EntryProx transmits data. 7. Command sequences are described in detail in the following sections. SELECTING TRANSACTION LOG INFORMATION You can selectively program specific transaction events to be included (or not) on the Transaction Log. By masking out certain events, you direct the unit not to save those events in memory and thus they do not appear in the log. The factory default is for all transaction events to be saved in memory and included in the log. The procedure follows:
1. Place the EntryProx unit in program mode. Press:
99 # Master Code * (default is 1234) HID CORPORATION 50 2. To turn OFF an event (keep it from being stored/logged), enter:
73 # Event Code # 0 # **
To turn an event ON, enter:
73 # Event Code # 1 # **
3. Press * to exit program mode. The Event Code is a two-digit number that represents a specific transaction as listed in the following table. The following transaction events can be set/cleared
(saved/not saved) and therefore downloaded/not downloaded. EVENT CODE 01 02 03 04 05 06 07 08 09 16 17 20 21 24 25 27 TRANSACTION EVENT Access Denied Program Denied Program Mode REX (Request to Exit) Door Ajar Door Closed Forced Door Log Erased Facility Access Download (to PDA) Access TGL ON (Toggle ON) TGL OFF (Toggle OFF) Lo ON (Lockout ON) Lo OFF (Lockout OFF) MSMTCH (Mismatch on Card and Code entry)
. DOWNLOADING A TRANSACTION LOG Using the optional Palm PDA with the DCD Program, you can download and display a Transaction Log via the EntryProxs IR port. Transaction Logs can be downloaded using two different methods, (1) by programming a card or code to dump the transaction log to the PDA and (2) by ENTRYPROX 4045-907 REV A 51 placing the EntryProx unit into program mode and manually entering the Display Transaction Log command. HID CORPORATION 52 PROGRAMMING A CARD OR CODE TO INITIATE A TRANSACTION LOG REPORT DUMP 1. Place the EntryProx unit in program mode. Press:
99 # Master Code * (default is 1234) 2. For a CODE DUMP, press:
50 # 2 # user location # code * code *
For a CARD DUMP, press:
50 # 2 # user location # ** <present card>
and then present the card at the proximity reader. 3. Press * to exit program mode. NOTE: Entering the programmed PIN code or presenting the card subsequently causes the unit to download a Transaction Log to the optional PDA. DOWNLOADING A TRANSACTION LOG MANUALLY 1. Place the EntryProx unit in program mode. Press:
99 # Master Code * (default is 1234) 2. Hold the IR Port on the optional PDA up to the EntryProx IR port steadily (about inch away; the IR port is located to the right of the yellow LED). 3. Start the DCD program on the Palm PDA, then touch Retrieve on the PDA 4. Then, on the EntryProx, press 70 # 0 # 0 # **
The PDA will display a progress bar while collecting the data, and when done will display End of Dump. You can touch Close/Stop on the PDA or wait for the unit to time out. When prompted for a Session Name, you can place your stylus on the line containing the date information and add to it or replace it with descriptive text. 3. Press * to exit program mode. The 70 command is logged in the transaction buffer
(in memory), providing a reference as to when the log was downloaded. Figure 18 shows a sample Transaction Log. ENTRYPROX 4045-907 REV A FIGURE 18 - TRANSACTION LOG 53 HID CORPORATION 54 The Palm PDA will store reports after they are downloaded. To view a stored report, touch Files, select a report from the list and click on Action. The drop-down menu selections are Info, View and Remove. Info gives the time and date the report was recorded. Remove allows you to delete the report. View displays the report. The top line of the screen shows the current line and total number of lines as you scroll or page up and down through the report. Here is a description of the report layout:
Top line Current Line/Total Lines Second line Session Data Transaction lines: Time, Date, User Location, Action TIME - 24-hour format. Date: mm/dd/yyyy User Location (1-2000) ACTION describes each event ERASING A TRANSACTION LOG The Transaction Log should be erased from memory in the EntryProx after being downloaded to prevent conflicting logs. To erase the log, enter the following sequence:
1. Place the EntryProx unit in program mode. Press:
99 # Master Code * (default is 1234)]
2. To erase the transaction log press:
76 # 00000 # 00000 # **
3. Press * to exit program mode. DOWNLOADING A PROGRAMMED USERS LIST The Programmed Users List can be downloaded to the optional Palm PDA via the units IR port. The list identifies the user location for each users data.. It also displays user locations that are not programmed, so to avoid an unnecessarily long file, the download can be stopped when a ENTRYPROX 4045-907 REV A sufficient percentage of records have been processed. The percentage of records downloaded is continually updated during the download process. 55 1. Place the EntryProx unit in program mode. Press:
99 # Master Code * (default is 1234)]
2. Hold the optional PDA up to the EntryProx IR port steadily (about inch away; the IR port is located to the right of the yellow LED) 3. Start the DCD program on the Palm PDA, then touch Retrieve on the PDA 4. Then, on the EntryProx, press 25 # 0 # 0 # **
The PDA will display a progress bar while collecting the data (Retrieving users %) and when done will display End of Dump. You can touch Close/Stop on the PDA or wait for the unit to time out. When prompted for a Session Name, you can place your stylus on the line containing the date information and add to it or replace it with descriptive text. 3. When the list is complete, press * to exit program mode. FIGURE 19 - PROGRAMMED USER LIST HID CORPORATION 56 Here is a description of the Report Layout:
Top line Title Second line Session Data Column 1 User location Column 2 user type (see table) Single PIN First letter access modes S B Both code and card E Either code or card Second letter user types T Toggle function N Normal User D Download Reports (dump) L Lockout Column 3 PIN CODE Column 4 - SITE CODE/CARD NUMBER. ENTRYPROX 4045-907 REV A
| frequency | equipment class | purpose | ||
|---|---|---|---|---|
| 1 | 2005-06-23 | 0.125 ~ 0.125 | DCD - Part 15 Low Power Transmitter Below 1705 kHz | Class II permissive change or modification of presently authorized equipment |
| app s | Applicant Information | |||||
|---|---|---|---|---|---|---|
| 1 | Effective |
2005-06-23
|
||||
| 1 | Applicant's complete, legal business name |
HID Global Corporation
|
||||
| 1 | FCC Registration Number (FRN) |
0005004122
|
||||
| 1 | Physical Address |
611 Center Ridge Dr.
|
||||
| 1 |
Austin, Texas 78753
|
|||||
| 1 |
United States
|
|||||
| app s | TCB Information | |||||
| 1 | TCB Application Email Address |
i******@ckccertification.com
|
||||
| 1 | TCB Scope |
A1: Low Power Transmitters below 1 GHz (except Spread Spectrum), Unintentional Radiators, EAS (Part 11) & Consumer ISM devices
|
||||
| app s | FCC ID | |||||
| 1 | Grantee Code |
JQ6
|
||||
| 1 | Equipment Product Code |
4045
|
||||
| app s | Person at the applicant's address to receive grant or for contact | |||||
| 1 | Name |
R******** C********
|
||||
| 1 | Title |
Compliance Engineering Manager
|
||||
| 1 | Telephone Number |
303-4********
|
||||
| 1 | Fax Number |
303-4********
|
||||
| 1 |
r******@hidglobal.com
|
|||||
| app s | Technical Contact | |||||
| 1 | Firm Name |
CKC Laboratories, Inc.
|
||||
| 1 | Name |
M******** C****
|
||||
| 1 | Physical Address |
5473-A Clouds Rest
|
||||
| 1 |
Mariposa, California 95338
|
|||||
| 1 |
United States
|
|||||
| 1 | Telephone Number |
800-5******** Extension:
|
||||
| 1 | Fax Number |
209-7********
|
||||
| 1 |
r******@ckc.com
|
|||||
| app s | Non Technical Contact | |||||
| 1 | Firm Name |
CKC Laboratories, Inc.
|
||||
| 1 | Name |
M****** C******
|
||||
| 1 | Physical Address |
5473-A Clouds Rest
|
||||
| 1 |
Mariposa, California 95338
|
|||||
| 1 |
United States
|
|||||
| 1 | Telephone Number |
800-5******** Extension:
|
||||
| 1 | Fax Number |
209-7********
|
||||
| 1 |
r******@ckc.com
|
|||||
| app s | Confidentiality (long or short term) | |||||
| 1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
| 1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
| if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
| app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
| 1 | Is this application for software defined/cognitive radio authorization? | No | ||||
| 1 | Equipment Class | DCD - Part 15 Low Power Transmitter Below 1705 kHz | ||||
| 1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | 4045C Entry Prox | ||||
| 1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
| 1 | Modular Equipment Type | Does not apply | ||||
| 1 | Purpose / Application is for | Class II permissive change or modification of presently authorized equipment | ||||
| 1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
| 1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
| 1 | Is there an equipment authorization waiver associated with this application? | No | ||||
| 1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
| app s | Test Firm Name and Contact Information | |||||
| 1 | Firm Name |
CKC Laboratories, Inc.
|
||||
| 1 | Name |
S**** B********
|
||||
| 1 | Telephone Number |
209-9******** Extension:
|
||||
| 1 | Fax Number |
866 7********
|
||||
| 1 |
q******@ckc.com
|
|||||
| Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
| 1 | 1 | 15C | 0.12500000 | 0.12500000 | |||||||||||||||||||||||||||||||||||||
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC