REVISIONS DESCRIPTION DATE APPROVED INITIAL PROTOTYPE RELEASE Revised specs REV 1 2 A INITIAL RELEASE REV SHEET 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 REV STATUS OF SHEETS REV SHEET 2 1 2 2 2 3 2 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 EXCEPT AS NOTED DIM ARE IN INCHES PER ANSI Y14.5
.XX .XXX ANGLES
+/-.01 +/-.005 +/-1 MATERIAL:
FINISH:
DO NOT SCALE DRAWING IRVINE, CALIFORNIA APPROVALS DATE DWG DESCRIPTION DRW: ANDRESKY 11/29/00 CHK:
APVD:
APVD:
MMDDYY MMDDYY MMDDYY MANUAL, INSTALL, IQ CARD READER SIZE CAGE CODE DWG NUMBER A SCALE: N/A 6055-910 SHEET: 1 of 5 REV A Install Manual 6055-910 Rev 2 IQ Card Reader _____________________________________________________________________________________________________ HID Corporation 9292 Jeronimo Road Irvine, CA 92618-1905 USA TEL (949) 598-1600 (800) 237-7769 FAX (949) 598-1690 Web page, E-mail - www.hidcorp.com - IQ Card Reader Installation Manual 6055-910 Rev A Page 2 of 5 PARTS LIST (Included) Quantity
- IQ Card Reader with snap-on cover and 18 cable 1
- #6-32 x 1 self-tapping panhead screw
- Installation manual 2 1 PARTS LIST (Not-Included) Quantity
- Wire splice 9
- DC Power supply 12 VDC 1 1 Mounting Instructions Determine an appropriate mounting location. The reader may be mounted to any surface, including metal. Drill two (2) 3/32-inch (2.5mm) holes approximately 1 inch deep for mounting the reader. Drill a 5/8-inch (16mm) hole for the cable. Remove the snap-on cover from the reader and secure the reader to the mounting surface. Route the cable from the reader and/or power supply to the host. A linear type power supply is recommended. Check all electrical codes for proper cable installation. For the cable connection to the Panel - Use Alpha
#1299C or equivalent. Test the operation of the reader. After completion of the test, replace the snap-on cover. See sheet 3 of this manual for the appropriate dimensioned drawings. For proper regulatory compliance, the drain wire should be disconnected at the power supply end of the cable. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. The Reader is intended to be powered from a limited power source output of a previously certified 2 Connecting the Reader to the Host Connect the reader to the host according to the wiring table below and the host installation guide. Signal Color Signal Color 9-14 VDC Red Beeper Yellow GND Black HOLD Blue D0 Green CARD PRES Violet D1 White RX Pink GRN LED Orange DTR Gray RED LED Brown TX BLU/WHT SHLD GND Drain 3 Testing and Operation When power is applied to the reader the beeper will beep once then the LED will flash green once _____________________________________________________________________________________________________ HID Corporation 9292 Jeronimo Road Irvine, CA 92618-1905 USA TEL (949) 598-1600 (800) 237-7769 FAX (949) 598-1690 Web page, E-mail - www.hidcorp.com - IQ Card Reader Installation Manual 6055-910 Rev A Page 3 of 5 For installation in 15 EU countries, see addendum installation
#6055-911) additional for power supply.
(dwg instructions. then red once. Present an ID card to the reader. The LED will momentarily turn green while the beeper beeps once, indicating that the card was read successfully. Important Product Specifications Power requirements (linear supply) Operating Voltage Range 9.0 14.0 VDC Absolute Maximum Voltage 16 VDC Average Current at 12V 100 ma Maximum cable distance 500 ft Wieg or C/D To host 50 ft RS-232 FCC Compliance Statement: This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. _____________________________________________________________________________________________________ HID Corporation 9292 Jeronimo Road Irvine, CA 92618-1905 USA TEL (949) 598-1600 (800) 237-7769 FAX (949) 598-1690 Web page, E-mail - www.hidcorp.com - IQ Card Reader Installation Manual 6055-910 Rev A Page 4 of 5 4 Front, side, and back view 4.1.1 Figure 1 _____________________________________________________________________________________________________ HID Corporation 9292 Jeronimo Road Irvine, CA 92618-1905 USA TEL (949) 598-1600 (800) 237-7769 FAX (949) 598-1690 Web page, E-mail - www.hidcorp.com - IQ Card Reader Installation Manual 6055-910 Rev A Page 5 of 5