all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
User Manual | Users Manual | 3.81 MiB | ||||
1 | Cover Letter(s) | |||||||
1 | External Photos | |||||||
1 | Internal Photos | |||||||
1 | ID Label/Location Info | |||||||
1 | Test Report | May 04 2016 | ||||||
1 | Cover Letter(s) | |||||||
1 | Cover Letter(s) | |||||||
1 | Test Report | May 04 2016 | ||||||
1 | Test Setup Photos | |||||||
1 | Test Report | May 04 2016 |
1 | User Manual | Users Manual | 3.81 MiB |
FARGO DTC5500LMX CARD PRINTER Model X002100 USER GUIDE PLT-02496 Version: 1.0 November 2015 hidglobal.com Page ii Copyright 2015 HID Global Corporation/ASSA ABLOY AB. All rights reserved. This document may not be reproduced, disseminated or republished in any form without the prior written permission of HID Global Corporation. Trademarks HID GLOBAL, HID, the HID logo, FARGO, iCLASS, iCLASS SE, OMNIKEY, and Seos are trademarks or registered trademarks of HID Global Corporation, or its licensors, in the U.S. and other countries. Contacts For additional offices around the world, see www.hidglobal.com corporate offices. Americas and Corporate Europe, Middle East and Africa (EMEA) 611 Center Ridge Drive Austin, TX 78753 USA Phone: 866 607 7339 Fax:
949 732 2120 Asia Pacific 19/F 625 Kings Road North Point, Island East Hong Kong Phone: 852 3160 9833 Fax:
852 3160 4809 Haverhill Business Park Phoenix Road Haverhill, Suffolk CB9 7AE England Phone: 44 (0) 1440 711 822 Fax:
44 (0) 1440 714 840 Brazil Condomnio Business Center Av. Ermano Marchetti, 1435 Galpo A2 - CEP 05038-001 Lapa - So Paulo / SP Brazil Phone: +55 11 5514-7100 HID Global Customer Support: support.hidglobal.com PLT-02496, Version: 1.0 November 2015 Contents 1.2 1.3 1.4 1.5 Chapter 1:
Specifications . 1-1 Regulatory Compliance . 1-1 1.1 Agency Listings . 1-1 1.1.1 1.1.2 United States . 1-2 Canada . 1-2 1.1.3 Taiwan . 1-2 1.1.4 1.1.5 Japan . 1-2 1.1.6 Korea . 1-2 Safety Messages . 1-3 Safety Messages - United States . 1-3 1.2.1 1.2.2 Safety Messages - French Canada . 1-4 Safety Messages - Taiwan . 1-5 1.2.3 1.2.4 Safety Messages - China . 1-6 Technical Specifications . 1-6 Functional Specifications. 1-9 Printer Components: Print Ribbons. 1-9 1.5.1 Ribbon Types and Print Counts . 1-10 1.6 Printer Components: Blank Cards . 1-10 Setup and Installation Procedures . 2-1 Selecting a Good Location . 2-1 2.1 2.1.1 About Moisture Condensation . 2-1 2.2 Unpacking and Inspection. 2-2 Print Driver Installation . 2-2 2.3 2.3.1 Driver Installation Instructions . 2-3 Installing the Print Ribbon Cartridge. 2-4 2.4 2.5 Installing Blank Cards into the Input Card Hopper. 2-5 2.6 Card Size Selection . 2-6 Printer Power . 2-8 2.7 Chapter 3: Printing Preferences . 3-1 Card Tab . 3-1 3.1 3.2 Device Options Tab . 3-3 Image Color Tab . 3-5 3.3 3.3.1 Advanced Image Color Tab . 3-7 3.4 Image Calibrate Tab . 3-8 3.5 Magnetic Encoding Tab . 3-9 Chapter 2:
November 2015 PLT-02496, Version: 1.0 Page iv 3.5.1 ISO Encoding Option . 3-11 3.5.2 Custom Encoding Option . 3-11 3.5.3 Raw Binary Encoding Option . 3-12 3.5.4 JIS II Encoding Option . 3-12 ISO Track Locations . 3-13 3.5.5 3.5.5.1 Sending the Track Information . 3-13 Lamination Tab . 3-15 3.6 3.7 Overlay/Print Area Tab . 3-17 3.7.1 Define a Print Area . 3-18 3.8 K-Panel Resin Tab . 3-19 Printer Info Tab . 3-20 3.9 Chapter 4: ToolBox . 4-1 Configuration Tab . 4-2 4.1 4.2 Calibrate Laminator Tab . 4-3 4.3 Calibrate Ribbon Tab . 4-4 4.4 Clean Printer Tab. 4-5 4.5 Advanced Settings Tab . 4-6 Settings Information . 4-7 Troubleshooting . 5-1 5.1 System Overview . 5-1 5.1.1 Sequence of Operations . 5-1 Printer Error Buttons . 5-2 5.2.1 Printer Error Button and On-screen Messages . 5-2 5.2.2 Error Messages . 5-2 5.2.3 Troubleshooting with the Error Message Table . 5-4 5.2.4 Printer-Specific Tools . 5-11 5.2.4.1 Additional Printer Specific Tools . 5-12 Chapter 6: Firmware Upgrades . 6-1 6.1 Upgrade Information . 6-1 Technical Support . 7-1 Technical Support . 7-1 7.1 7.1.1 Reading the Serial Numbers on a FARGO Printer . 7-1 Chapter 5:
Chapter 7:
4.5.1 5.2 PLT-02496, Version: 1.0 November 2015 Chapter 1 Specifications The purpose of this section is to provide specific information on the Regulatory Compliances, Agency Listings, Technical Specifications and Functional Specifications for the HDP8500 Card Printer/Encoder. 1.1 Regulatory Compliance Agency UL CSA FCC CE Regulatory Compliance The Card Printer is listed under UL 60950-1 (2nd edition) Information Technology Equipment. File Number: E145118 The printer manufacturer has been authorized by UL to represent the Card Printer as CSA Certified under CSA Standard C22.2 No. 60950-1-07 2nd edition File Number: E145118 The Card Printer complies with the requirements in Part 15 of the FCC rules for a Class A digital device. The Card Printer has been tested and complies with EN300-330-1, EN300-330-2, EN301-489-
1, EN60950-1:2006 + A11:2009 Note: Based on the above testing, the printer manufacturer certifies that the card printer complies with the following of the European Community and has placed the CE mark on the Card Printer. LVD 2006/95/EC, EMC 2004/108/EC, R&TTE 1999/5/EC, ROHS 2011/65/EU 1.1.1 Agency Listings Agency Emissions and Immunity Standards Safety Standards Additional Agency Listings Listing FCC Part 15 Class A, RSS-GEN, RSS 210, CNS 13438, EN55022 Class A, EN55024, EN6100-3-2, EN6100-3-3, EN300-330-1, EN300-330-2, EN301-489-1, EN301-489-3, GB9254, GB17625 UL IEC 60950-1 (2nd edition), CSA C22.2 No. 60950-1-07( 2nd edition), EN60950-1, GB4943, CNS14336 CCC, BSMI, KC November 2015 PLT-02496, Version: 1.0 Page 1-2 Specifications 1.1.2 United States This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference; in which case, correction of the interference is at the users expense. IMPORTANT: Changes or modifications to an intentional or unintentional radiator not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. 1.1.3 Canada This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. 1.1.4 Taiwan 1.1.5 Japan
"
( AC-12056 ) RFID ?
?
1.1.6 Korea
(A ) ,
. PLT-02496, Version: 1.0 November 2015 Specifications Page 1-3 1.2 Safety Messages 1.2.1 Safety Messages - United States Symbol Critical Instructions for Safety Purposes Failure to follow these guidelines results in personal injury or death. To prevent personal injury or death:
Reference the following safety messages before performing an operation. Always remove the power cord prior to performing repair procedures, unless otherwise specified. Ensure only qualified personnel perform these procedures. This device is electro statically sensitive. Damage to the device may occur if exposing it to static electricity discharges. To prevent damage:
Reference the following safety messages before performing an operation. Observe all established Electrostatic Discharge (ESD) procedures while handling cables in or near the circuit board and printhead assemblies. Always wear an appropriate personal grounding device. Always remove the ribbon and cards from the printer before making any repairs, unless otherwise specified. Remove jewelry and thoroughly clean hands before working on the printer. This symbol warns of an electrical hazard that could result in personal injury or death. Danger:
ESD:
Caution:
Caution:
For safety purposes, do not use Ethernet for a direct connection outside of the building. November 2015 PLT-02496, Version: 1.0 Page 1-4 Specifications 1.2.2 Safety Messages - French Canada Symbole Instructions critiques visant la Scurit Danger:
ESD:
Attention:
Attention:
Si ces directives ne sont pas suivies les rsultats peuvent tre des lsions corporelles ou la mort. Pour viter des lsions corporelles ou la mort:
Rapportez-vous aux avis suivants de scurit avant de procder une opration. Retirez toujours le cble dalimentation avant deffectuer des procdures de rparation, sauf spcification contraire. Assurez-vous quuniquement des personnes qualifies ralisent des procdures. Ce dispositif est sensible llectricit statique. Il peut souffrir des dommages sil est expos des dcharges lectrostatiques. Pour viter des dommages:
Rapportez-vous aux messages suivants avant de procder une opration. Suivez toutes les procdures de Dcharges Electrostatiques (ESD) en vigueur durant le maniement des cbles dans ou proximit des Ensembles de Cartes de Circuit Imprim et Tte dImpression. Portez toujours un dispositif de mise la terre personnelle approprie. Retirez toujours le ruban et les Cartes de lImprimante avant deffectuer toute rparation, sauf spcification contraire. Retirez tous bijoux et lavez soigneusement vos mains avant de travailler lImprimante. Ce symbole est un avis de pril lectrique passible de rsulter en lsion corporelle ou mort. Pour des motifs de scurit, nutilisez pas Ethernet pour une connexion directe hors du btiment. PLT-02496, Version: 1.0 November 2015 Specifications Page 1-5 1.2.3 Safety Messages - Taiwan
:
:
November 2015 PLT-02496, Version: 1.0 Page 1-6 Specifications 1.2.4 Safety Messages - China
:
:
(ESD) 2000m
( -RoHS) 1.3 Technical Specifications Component Description Card Cleaning Card cleaning roller integrated into the ribbon cartridge. A new cleaning roller is included with each ribbon cartridge. Card Size and Type Supported CR-80 (3.375"L x 2.125"W / 85.6mmL x 54mmW) CR-79 (3.313L x 2.063W / 84.1mmL x 52.4mmW Card (Standard) Sizes CR-80 edge-to-edge (3.36"L x 2.11"W / 85.3mmL x 53.7mmW) CR-79 (3.3L x 2.04W / 83.8mmL x 51.8mmW) Card Thickness Display
.009 - .040 / 9 mil 40 mil / .229mm 1.016mm Graphical Display PLT-02496, Version: 1.0 November 2015 Specifications Page 1-7 Component Description Encoding Options Supported Hopper (input) Card Capacity Hopper (output) Card Capacity Hopper (Reject) Card Capacity Interface Operating Conditions 125kHz (HID Prox) reader 13.56 MHz (iCLASS, MIFARE, ISO 14443 A/B, ISO 15693) read/write encoder Contact Smart Card Encoder reads from and writes to all ISO7816 1/2/3/4 memory and microprocessor smart cards (T=0, T=1) as well as synchronous cards. ISO Magnetic Stripe Encoding, dual high- and low-coercivity, Tracks 1,2 and 3 Single hopper: 100 cards (.030 / .762.mm) Dual hopper: 200 cards (.030 / .762 mm) 100 cards (.030 / .762.mm) 100 cards (.030 / .762.mm) USB 2.0 and Ethernet with internal print server Operating Temperature: 65 to 80 F (18 to 27 C) Humidity: 20 - 80% non-condensing Operating Systems Windows XP / Vista (32 bit & 64 bit) / Server 2003 & 2008 / Windows 7 (32
& 64 bit) / Windows 8 (32 & 64 bit) / Linux Options Single Wire Ethernet and USB 2.0 Interface for inline printing and encoding Single wire Ethernet encoding is only available for iCLASS and Contact Smart Card encoding) Dual-Sided Printing Module Upgradable Dual Input Card Hopper Same-Side Input / Output Card Hopper Upgradable Smart Card Encoding (contact / contactless) Upgradable Magnetic Stripe Encoding Upgradable Printer Cleaning Kit Print Colors Print Method Print Resolution Up to 16.7 million colors / 256 shades per pixel Dye-Sublimation/ Resin Thermal Transfer 300 DPI (11.8 dots per mm); continuous tone November 2015 PLT-02496, Version: 1.0 Page 1-8 Specifications Component Description Print Ribbon Options Print Speed Full-color with resin black and overlay panel, YMCKO* (500 prints) Full-color half-panel with resin black and overlay panel, YMCKO*
(850 prints) Full-color with two resin black panels and overlay panel, YMCKOK* (500 prints) Full-color with fluorescing, two resin black panels and overlay panel, YMCFKO* (500 prints) Full-color with fluorescing, two resin black panels and overlay panel, YMCFKOK* (400 prints) Resin black and overlay panel, KO* (1250 prints) Dye-sublimation black and overlay print, BO* (1250 prints) Resin black (standard and premium) (3000 prints) Resin green, blue, red, white (1000 prints) Resin silver (2000 prints) Resin gold (1000 prints) Rewrite technology No ribbon is required
* Indicates the ribbon type and the number of ribbon panels printed where Y=Yellow, M=Magenta, C=Cyan, K=Resin Black, O=Overlay F=Fluorescing Resin 6 seconds per card (K*) 8 seconds per card (KO*) 16 seconds per card (YMCKO*) 24 seconds per card (YMCKOK*) Print speed indicates an approximate batch print speed and is measured from the time a card feeds into the printer to the time it ejects from the printer. Print speeds do not include encoding time or the time needed for the PC to process the image. Process time is dependent on the size of the file, the CPU, amount of RAM and the amount of available resources at the time of the print.
* Indicates the ribbon type and the number of ribbon panels printed where Y=Yellow, M=Magenta, C=Cyan, K=Resin Black, O=Overlay, F=Fluorescing Resin Printer Memory 128 MB RAM Power Source Voltage, Amp & Frequency Supply Voltage/Amp: 100-240 VAC, 1.6A Max Supply Frequency: 50 Hz and 60 Hz Ship Weight Software Warranty Single-Sided: 8 lbs. / 3.63 Kg; Dual-Sided: 10 lbs. / 4.54 Kg FARGO Workbench Diagnosis Utility Printer- 2 years Printhead: 2 years unlimited pass with UltraCard PLT-02496, Version: 1.0 November 2015 Specifications Page 1-9 1.4 1.5 Functional Specifications This card printer utilizes two different, yet closely related printing technologies to achieve its remarkable direct-to-card print quality for dye-sublimation and resin thermal transfer. Printer Components: Print Ribbons The card printer utilizes both dye-sublimation and/or resin thermal transfer methods to print images directly onto blank cards. Because the dye-sublimation and the resin thermal transfer print methods each provide their own unique benefits, Print Ribbons are available in resin-only, dye-sublimation-only and combination dye-sublimation/resin versions. To make it easier to remember which print ribbons are which, a letter code has been developed to indicate the type of ribbon panels found on each ribbon. This letter code is as follows:
= Dye-Sublimation Yellow Panel
= Dye-Sublimation Magenta Panel
= Dye-Sublimation Cyan Panel
= Resin Black Panel (Premium unless otherwise stated)
= Clear Protective Overlay Panel
= Fluorescing Panel November 2015 PLT-02496, Version: 1.0 Page 1-10 Specifications 1.5.1 Ribbon Types and Print Counts The following table lists print capability of each ribbon type. Ribbon YMCKO Full Color/Resin Black / Overlay YMCKO Half Panel Full Color (1/2)/Resin Black/Overlay YMCFKO - Full Color/UV Fluorescing/Resin Black/Overlay YMCKK - Full Color/2 Resin Black YMCKOK - Full Color/2 Resin Black/Overlay YMCFKOK - Full Color/UV Fluorescing/2 Resin Black/Overlay K Standard Resin K Premium Resin Colored Resin KO - Premium Black Resin/Overlay BO - Dye-Sub Black/Overlay None Rewritable 1.6 Printer Components: Blank Cards Count 500 850 500 500 500 400 3000 3000 2000 1250 1250 Supported Type Card Size Card Surface UltraCard Brand Cards Description The Card Printer accepts standard CR-79 and CR-80 sized cards. Suitable cards must have a polished PVC surface free of fingerprints, dust or any other types of embedded contaminants. In addition, cards must have a completely smooth, level surface in order for the printer to achieve consistent color coverage. Certain types of proximity cards have an uneven surface that inhibits consistent color transfer. Certain types of smart card chips are raised slightly above the cards surface, which also results in poor color transfer. The UltraCard product line, available exclusively as part of HID Global FARGO brand secure card issuance solutions, has a long standing reputation among dealers and end-Users for consistent quality in construction. In addition to blank stock, the UltraCard line is available in a variety of configurations for magnetic stripe, custom holograms and other additional anti-counterfeiting feature. UltraCard Premium is the preferred card for Direct-to-Card (DTC) applications that require a higher quality card. The UltraCard Premiums composite material construction provides for maximum durability, flexibility and card life, with optimal resolution print quality for lamination and fluorescent panel Ribbon printing applications. UltraCard PVC cards are medium-durability cards for a glossy, photo quality finish. These cards are manufactured to ensure clean, scratch-free cards for high-
quality prints and extended printhead life. PLT-02496, Version: 1.0 November 2015 Chapter 2 Setup and Installation Procedures This section describes the setup and installation for the DTC5500LMX Card Printer. 2.1 Selecting a Good Location The following guidelines help to ensure optimal printing performance:
Place the unit in a location with adequate air circulation to prevent internal heat buildup. Use the printer's dimensions as a guideline for the minimum clearances to the unit. Note: Allow for adequate clearance in front of the unit to accommodate the unit with its covers open. Do not install unit near heat sources such as radiators or air ducts or in a place subject to direct sunlight, excessive dust, mechanical vibration or shock. 2.1.1 About Moisture Condensation If the unit is brought directly from a cold to a warm location or is placed in a very damp room, moisture may condense inside the unit. Should this occur, print quality may not be optimal. Leave the unit unplugged in a warm, dry room for several hours before using to evaporate any moisture. Caution: For safety purposes, Ethernet is not intended for a direct connection outside of the building. Attention: Pour des raisons de scurit, Ethernet n'est pas conu pour une connexion directe l'extrieur du btiment. November 2015 PLT-02496, Version: 1.0 Setup and Installation Procedures Page 2-2 2.2 Unpacking and Inspection While unpacking the printer, inspect the carton to ensure that no damage has occurred during shipping. Make sure that all supplied accessories are included with the unit:
Software Installation CD (includes Printer Driver, Online User Guide and Printer Diagnostic Tool) US/EU Power Cable USB Cable (2.0) Warranty Statement 2.3 Print Driver Installation This section describes the printer driver installation requirements and standard procedures. Requirements are listed below. The DTC5500LMX Print Driver supports the following:
Windows Vista 32 bit with SP2 Windows Vista 64 bit with SP2 Windows XP 32 bit with SP3 Windows Server 2003 (R1) 32 bit Windows Server 2008 (R1) 32 bit with SP2 Windows Server 2008 (R1) 64 bit with SP2 Windows Server 2008 R2 Windows 7 32 bit and 64 bit Windows 8 32 bit and 64 bit For more information on supported Operating Systems, please visit the HID Global support page. PLT-02496, Version: 1.0 November 2015 Page 2-3 Setup and Installation Procedures 2.3.1 Driver Installation Instructions Start the installation process by inserting the Driver CD into the computer; then, follow the Installation Wizard screen prompts. 1. Select Install the Printer Driver to go through the driver installation wizard. 2. Select the Install the FARGO Workbench to install the Diagnostic program. 3. All versions of Windows require Administrator rights. 4. Go to Start > Devices & Printers, right-click the DTC5500LMX printer icon and select Printing preferences to setup the printer driver after it has been installed. November 2015 PLT-02496, Version: 1.0 Setup and Installation Procedures Page 2-4 2.4 Installing the Print Ribbon Cartridge FARGO Direct-to-Card Printers require highly specialized supplies to function properly. The FARGO DTC5500LMX Card Printer uses a one piece, disposable ribbon cartridge system. To maximize printer durability, reliability and printed card quality, you must use only FARGO-certified supplies. Your FARGO warranty is void, where not prohibited by law, if you use supplies other than FARGO-
certified supplies. Printer cleaning is recommended with each ribbon change to ensure quality printed cards. Resin-only print ribbons consist of a continuous roll of a single resin color. No protective overlay panel
(O) is provided because resin images do not require the protection of an overlay. To Install the Print Ribbon Cartridge:
1. Pull open the front assembly. 2. 3. Close the front cover. Insert the print ribbon cartridge into the printer. PLT-02496, Version: 1.0 November 2015 Page 2-5 Setup and Installation Procedures 2.5 Installing Blank Cards into the Input Card Hopper The FARGO DTC5500LMX Card Printer is capable of printing single feed cards and multiple feed cards (batch mode). To print a single feed card, remove all cards from the input card hopper, leave its door closed and place a card in the single feed card slot (which can be used repeatedly). 1. Load the cards with the print side down and (if applicable) the magnetic strip up and towards the front of the printer. Information: Do not run the cards with a contaminated, dull or uneven surface through the Printer. Printing onto such cards may lead to poor print quality and can greatly reduce the life of the printhead. Card types include PVC or PVC finish. Cards eject into the output hopper or reject hopper. Each input hopper holds 100 cards. Certain types of smart card chips are raised slightly above the cards surface, which may result in poor color transfer. Design the card with white space surrounding the chip. To print using single feed, remove all cards from the input card hopper, leave its door closed. Place a card in the single feed card slot (which can be used repeatedly). 2. Open the input card hopper door. 3. Press the card hopper load lever down until the card tray locks into place. 4. Load up to 100 cards into the hopper with the print side down. Note: If using cards with a magnetic stripe, the magnetic stripe should be loaded with the stripe up and to the front of the Printer. 5. Close the input card hopper door to release the lever to the printing position. November 2015 PLT-02496, Version: 1.0 Setup and Installation Procedures Page 2-6 2.6 Card Size Selection The Card Size (standard CR-70 and CR-80) must be set in the printer and in the Printer Driver Preferences. 1. Slide out the front assembly, which exposes the card switch. 2. The card switch is clearly marked with the 2 card options. Slide the switch to the card size needed. LEFT for the CR-79 card. RIGHT for the CR-80 card. PLT-02496, Version: 1.0 November 2015 Page 2-7 Setup and Installation Procedures 3. From the Driver Printing Preferences (right-click the printer icon and select Printing preferences), Select the Card tab. 4. Select the correct card size from the Card Size pull-down list. 5. Click OK. November 2015 PLT-02496, Version: 1.0 Setup and Installation Procedures Page 2-8 2.7 Printer Power To connect power to the printer, follow this procedure. Note: Do not connect the printers USB cable until prompted during the printer driver installation. 1. Plug the power cable into the back of the printer. 2. Plug the wall power cable into a standard 100-240VAC power outlet. 3. Press the printers ON/OFF button to power on the printer. Printer Back Printer Front Receptor for power cable Printer ON/Off Button Note: The printer powers down during the sleep time but automatically powers up when a print job is sent. PLT-02496, Version: 1.0 November 2015 Chapter 3 Printing Preferences This chapter provide an overview of the Printing Preferences of the DTC5500LMX. To locate the Printing Preferences menu select Start > Devices and Printers. Right-click the printer icon and select Printing preferences. 3.1 Card Tab Use the Card tab to select options for the card as well as diagnostics and calibration. November 2015 PLT-02496, Version: 1.0 Page 3-2 Printing Preferences Field Card Size Orientation Copies Card Hopper Selection Diagnostics ToolBox Test Print About Definition Select the appropriate card option:
CR-79: 3.313 x 2.063 inch (84.14 x 52.39 mm). CR-80: 3.452 x 2.204 inch (87.7 x 56 mm). Inches/mm: Card sizes will display in inches or mm, depending on the option selected. Print Width & Print Length: The dimensions of the total print area for each card size. Note: These print area dimensions are .04 in (1 mm) larger than the actual card size. This allows the printer to overprint images to ensure they will appear edge-to-edge when transferred to the card. When designing a card format, always set the card size within the card design program to the exact print length and width dimensions of the card. Card Thickness (mil): Select the card thickness from the pull-down list. Options are 10, 20, 30 (default), and 40 mil. There are two selections for card printing orientation. Portrait prints card vertically. Landscape prints card horizontally. Select the number of copies to print using Test Print. First Available: Selects the first available hopper (default). Top: Selects the top hopper. Bottom: Selects the bottom hopper. This will launch the Workbench program, which is included on the driver CD. Also see the Workbench user guide located on the driver CD. See Chapter 4: ToolBox. Sends one or more self-test prints to the printer. This opens a dialog box containing the copyright information, the drivers version number and date code. PLT-02496, Version: 1.0 November 2015 Printing Preferences Page 3-3 3.2 Device Options Tab Use the Device Options tab to set print options. Field Supplies Dual Sided Definition Automatically detect the installed Ribbon and Film for every print job: Use this option to verify that the ribbon type selected matches the installed ribbon. The printer changes the Ribbon Type to the correct setting. Ribbon Type: Use this option to manually select the ribbon type. Note: the Automatically detect the installed Ribbon and Film for every print job option must be unselected for this option to be active. Select from the available ribbon types on the drop-down list. For rewritable cards, select NONE Re-Writable. Note: The Dual Sided area is grayed out when the printer is single-sided only. Print Both Sides: Prints on the front and back sides of the card. Split 1 Set of Ribbon Panels: Prints on the front and back sides of the card using one ribbon panel. Print Back Image on Front of Card: Prints the first page of a two-page print file on the cards backside. This option can also be used to print black resin on a smart cards chip side. Note: The second page of the file is printed on the cards front side. Print Back Side Only: Prints only on the card back side. November 2015 PLT-02496, Version: 1.0 Page 3-4 Printing Preferences Field Options Definition Note: The availability of options below is based on the Ribbon Type selected. Rotate Front 180 Degrees: Adjusts the orientation of the first page of the card design to accommodate the location of a chip or RFID sensor. Rotate Back 180 Degrees: Adjusts the orientation of the second page of the card design to accommodate the location of a chip or RFID sensor. Disable Printing: Disables printing. Write Only: For rewritable cards. The default setup is for the printer to first erase the entire card and then write new information on the card. There is no option to select specific areas to erase. However, to print or erase a section, use the Overlay/Print Area tab. Select the specific area in the same manner as a print job with a color ribbon. To erase many cards, use the FARGO Workbench Re-Writable Card Eraser option. It does not print. It only erases. Note: No ribbon is used with rewritable cards. Do not load a ribbon into the printer when using this process. Printing on a rewritable card with a ribbon will damage the card. Invert F-panel Image: Creates a negative of the fluorescent image. Used with Fluorescent Panel Ribbon Type. Encrypt Job Data: Encrypts information about the print job for enhanced security. PLT-02496, Version: 1.0 November 2015 Printing Preferences Page 3-5 3.3 Image Color Tab Use the Image Color tab to control the sharpness, contrast, and gamma of the printed image, as well as the individual color balance of yellow, magenta and cyan. Field Description Color Matching: There are two selections for color matching in the drop-down list. Image Quality None: Select this option if:
- interested in print speed rather than print color
- color correcting an image that has been previously printed, or
- using third-party color matching software System Color Management: To perform color corrections through a complex color matching algorithm. Note: This option shifts colors so they more closely match how they appear on screen. Algebraic: Use the Algebraic color-matching algorithm. Resin Dither: Select the appropriate dither method according to the type of image to be printed. Optimized for Graphics: Select this option when printing lower quality images
(e.g., clip-art, logos, etc.) with resin. Optimized for Photo: Select this option when printing photo quality images with resin. November 2015 PLT-02496, Version: 1.0 Page 3-6 Printing Preferences Field Heat Advanced Settings Description The Heat area includes sliders for adjusting the temperature when printing with various types of ribbons. Dye-Sub Intensity (YMC): Move the slider to the left to use less heat in the printing process, resulting in a lighter print. Move the slider to the right to use more heat, resulting in a darker print. Note: This slide only affects those images printed with dye-
sublimation ribbon panels. Resin Heat, Front: (K): Move the slider to the left to use less heat in the printing process, resulting in a lighter or less saturated print. Move the slider to the right to use more heat, resulting in a darker or more saturated print. Note: This control can be helpful for fine-tuning the sharpness of resin text and bar codes. Resin Heat, Back: (K): Move the slider to the left to use less heat in the printing process, resulting in a lighter or less saturated print. Move the slider to the right to use more heat, resulting in a darker or more saturated print. Overlay Heat: (O): Move the slider to the left to use less heat in the printing process, resulting in a lighter or less saturated print. Move the slider to the right to use more heat, resulting in a darker or more saturated print. Default: Clicking the will return all options to factory settings. See Section 3.3.1: Advanced Image Color Tab. PLT-02496, Version: 1.0 November 2015 Printing Preferences Page 3-7 3.3.1 Advanced Image Color Tab Select Advanced Settings on the Image Color tab. The graphic on the right will display the current settings. Group or Field Image Quality Balance Description Sharpness: Move the slider to the right to sharpen the image. Move the slider to the left to decrease sharpness. Contrast: Move the slider to the right to increase contrast in the image. Move the slider to the left to decrease contrast. Gamma: Move the slider to the right to increase gamma in the image. Move the slider to the left to decrease gamma. Yellow Balance: Move the slider to the right to increase the amount of yellow in the image. Move the slider to the left to decrease the amount of yellow. Magenta Balance: Move the slider to the right to increase the amount of magenta in the image. Move the slider to the left to decrease the amount of magenta. Cyan Balance: Move the slider to the right to increase the amount of yellow in the cyan. Move the slider to the left to decrease the amount of cyan. November 2015 PLT-02496, Version: 1.0 Page 3-8 Printing Preferences 3.4 Image Calibrate Tab Use the Image Calibrate tab to control the position of the printable area in relation to the card. Group or Field Image Position Description Use the Image Position controls to position the image on a card. Adjust the image position values by clicking on the Vertical and Horizontal adjustment arrows. The image position will flip and rotate according to the selection of portrait, landscape, or rotate 180 degrees on previous screens PLT-02496, Version: 1.0 November 2015 Printing Preferences Page 3-9 3.5 Magnetic Encoding Tab Select the Magnetic Encoding tab to configure the Magnetic Stripe encoding process. These options are only available if the printer has an optional Magnetic Stripe Encoding Module installed. Field Description Encoding Mode: Change the encoding mode and coercivity setting or modify the ISO standards for tracks 1, 2 and 3. Options are:
ISO Encoding (see Section 3.5.1: ISO Encoding Option) Custom Encoding (see Section 3.5.2: Custom Encoding Option) Raw Binary Encoding (see Section 3.5.3: Raw Binary Encoding Option) JIS II Encoding (see Section 3.5.4: JIS II Encoding Option) Encoding Options Coercivity: Select the coercivity option (Oersted [Oe]) for the magnetic stripe type that matches the card type. High Coercivity = 4000 Oersted FARGOs High Coercivity UltraCard IIIs are 2750 Oersted Medium Coercivity = 600 Oersted Low Coercivity = 300 Oersted Shift Data Left: Select this option to shift the recorded magnetic data to the left-hand side of the card's magnetic stripe. This is useful in situations that require cards to be readable with insert type readers November 2015 PLT-02496, Version: 1.0 Page 3-10 Printing Preferences Field Description Encoding Mode: Displays the Encoding Mode selected above. Character Size: Customize the character data size used to encode the magnetic data on the currently selected track. Note: Character size includes the parity bit (if enabled). Selections vary for the selected encoding mode. Options are 4, 5, 7, or 8 Bits Magnetic Track Options Custom Encoding: 5, or 7 Bits Raw Binary Encoding: 4 or 8 Bits ASCII Offset: Customize the character ASCII offset used to encode the magnetic data on the currently selected track. Note: This character-offset value is subtracted from the ASCII value of each magnetic stripe data character prior to encoding on the track. Options are: NULL, SPACE, ZERO Bit Density: Customize the bit recording density (Bits Per Inch) used to encode the magnetic data on the currently selected track. Options are: 75, 128, 210, or Custom BPI. LRC Generation: Customize the LRC generation mode used to encode the magnetic data on the currently selected track. Options are: No LRC, Even Parity, or Odd Parity Character Parity: Customize the encoding mode used to encode the magnetic data on the currently selected track. Options are: No Parity, Even Parity, Odd Parity Reverse Bit Order: This option is used to reverse the character bits for the encryption of data in specific programs. Add Leading Zeros: This option is used to add a set number of leading zeros to the magnetic string in order to move the starting point of the encoded data in specific programs for encryption of data. Default: Clicking this resets defaults for only the current track. PLT-02496, Version: 1.0 November 2015 Printing Preferences Page 3-11 3.5.1 ISO Encoding Option With ISO Encoding, a formatted set of characters are sent down. This selection activates the Track tabs. However, all functions on the Track tabs are inactive or gray and display ISO defaults, which are the defaults listed for each track below. The Shift Data Left option remains inactive. 3.5.2 Custom Encoding Option With Custom Encoding, all options are active. The default is ISO Encoding. Note: The defaults are the same as the ISO Encoding defaults. All functions on the Magnetic Track Options tabs are active. November 2015 PLT-02496, Version: 1.0 Page 3-12 Printing Preferences 3.5.3 Raw Binary Encoding Option With Raw Binary Encoding, a raw binary string rather than a formatted set of characters is sent down. The Coercivity drop-down function is active and the Shift Data Left option is not active. All functions on the Magnetic Track Options tabs are inactive except for Bit Density. 3.5.4 JIS II Encoding Option With JIS II Encoding, specific standards are used. This selection disables all the Magnetic Track Options tabs, the Coercivity and Shift Data Left options. The default Coercivity is 600 Oe. PLT-02496, Version: 1.0 November 2015 Printing Preferences Page 3-13 3.5.5 ISO Track Locations The magnetic Encoding Module encodes onto tracks in accordance with an ISO 7811-2 Magnetic Stripe. 3.5.5.1 Sending the Track Information Magnetic track data is sent in the form of text strings from the application software to the printer driver. In order for the printer driver to differentiate between magnetic track data and the rest of the printable objects, specific characters must be added to encode the magnetic data. These specify the data that is to be encoded, the tracks to encode, and mark the start and stop of the data string. In some cases, these specific characters are automatically added to the string of track data by ID software applications. In most cases, the user must carefully add these characters to the string of data. If these characters are not added to the track data, the text intended for the magnetic track will appear as printed text on the card. To avoid this, track information must be entered as described below. When entering track data, the ~ (tilde) character is entered first, followed by the track number (1, 2 or 3) on which the data should encode. This is followed by the data to be encoded The first character of this data string must be the track's specific Start Sentinel (SS) and the last character must be the specific End Sentinel (ES). The characters or data in between the SS and ES can include all of the valid characters specific to each track. The number of these characters, however, is limited by each track's maximum character capacity. When segmenting track data, the appropriate Field Separator (FS) must be used. The ASCII Code and Character Table shows the SS, ES, FS and the valid characters defined for each track November 2015 PLT-02496, Version: 1.0 Page 3-14 Printing Preferences Reviewing the Sample String Track 1: ~1%JULIEANDERSON^1234567890?
Track 2: ~2;1234567890987654321?
Track 3: ~3;1234567890987654321?
Track Track 1 Track 2 Track 3 Start Sentinel End Sentinel
%
;
;
?
?
?
Field Separator Valid Characters
^
ASCII 32-95 (See the table)
=
=
ASCII 48-63 (See the table) ASCII 48-63 (See the table) Maximum Number of Characters 78 39 106 ASCII Code and Character Table ASCII Code Character ASCII Code Character ASCII Code Character 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 space
!
#
$
%
and
'
(
)
*
+
'
-
.
/
0 1 2 3 4 5 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 6 7 8 9
:
;
<
=
>
?
@
A B C D E F G H I J K 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 L M N O P Q R S T U V W X Y Z
[
\
]
^
_ PLT-02496, Version: 1.0 November 2015 Printing Preferences Page 3-15 3.6 Lamination Tab These options allow control of the printer's lamination process. When no laminator is detected, the lamination tab is active but all functions are disabled. Field Lamination Position Lamination Speed Lamination Side Description Use this control to adjust the horizontal position of the laminate. Only the horizontal position needs adjustment. Default is 0. To adjust the position, click on the horizontal adjustment arrows. The adjustment arrows point in the direction the patch will move on the card. The maximum horizontal value is 100 Pixels (10 Pixels = 0.03 [0.8mm]). Transfer Dwell Time: Adjust this control for the throughput speed of a card in seconds per inch, default is 2.0 seconds per inch. Maximum Limit - 4.9 seconds per inch Minimum Limit - 0.8 seconds per inch Specify the side(s) of the card to laminate:
No Lamination Front Back Both November 2015 PLT-02496, Version: 1.0 Page 3-16 Printing Preferences Field Lamination Type Automatically Detect Installed Laminate for Every Print Job Description Laminate type can be specified for one or two cartridges, depending on cartridge availability. The type of laminate affects the temperature required for lamination. Transfer Temperature: Adjust the temperature by moving the slider. Use the option to auto-detect the installed lamination. Default: To automatically set the lamination dwell time and transfer temperature. PLT-02496, Version: 1.0 November 2015 Printing Preferences Page 3-17 3.7 Overlay/Print Area Tab Use the Overlay / Print Area tab to control and customize where the Overlay (O) panel and/or the print area appear on the card. By default, this option is set to print and overlay the entire card. The orientation of the card display area is determined by the orientation specified in your template. For additional information, see Appendix A. Field Front/Back Description Specify the side of the card to apply the area definition. Overlay/Print Area Define the Overlay or Print Area. Full Card: Select this option to overlay and/or print the entire card. Defined Area(s): Select this option to overlay and/or print only in the selected and defined area(s). Undefined Area(s): Select this option to overlay and/or print in the space outside the selected and defined area. Omit Smart Chip Area: Select this option to overlay and/or print only in the space outside the standard location of a smart chip. Omit Mag Strip Area: Select this option to overlay and/or print only in the space outside the standard location of an ISO-standard magnetic stripe. Omit Signature Area: Select this option to overlay and/or print only in the space outside the standard location of a signature panel. November 2015 PLT-02496, Version: 1.0 Page 3-18 Printing Preferences Field Overlay/Print Area
(continued) Security Options Description For Print and Overlay: This option applies the defined area to both the print and overlay processes. For Overlay Only: The defined are applies only to the overlay process. The entire card prints and only the overlay is affected. For Print Only (No Overlay): The defined are applies only to the print process. Overlay is disabled. Visual Security Solutions: Enables a visual security option. The options are only available for the Front side of a card. The default value for all cards is No Visual Security. This field presents options based on the orientation of the card in the template. Landscape designs offer:
A Upper Left B Upper Right C Lower Left D Lower Right Verimark: This option is reserved for future use. HoloMark: Use this option for hologram security. Note: When an option is selected, the Overlay/Print Area is disabled and the Security Options become selectable. Portrait designs offer:
E Upper Left F Upper Right G Lower Left H Lower Right 3.7.1 Define a Print Area 1. Select Front or Back. 2. Select an Overlay/Print Area from the drop-
down list. When an option is selected, a default blacked area appears on the card design area grid. 3. Click and drag to enlarge or move the area to the preferred location on the card. The size and coordinates of the area update with the changes. Note: To delete the area, click Delete. 4. When complete, click OK. PLT-02496, Version: 1.0 November 2015 Printing Preferences Page 3-19 3.8 K-Panel Resin Tab Use the K-Panel Resin tab to control where the resin black (K) panel of a full-color ribbon is printed. If printing with a ribbon type that does not have a K-Panel, all K-Panel Resin options will be disabled. Resin black text is desirable due to its sharp, saturated color (good for barcodes). By default, the printer driver will print all True-type black text and True-type barcodes with the resin black (K) panel of the print ribbon. If printing black text or barcodes that are not True-type, select a Print All Black with K Panel option. The printer driver will print areas of the image where it finds black coloring with the print ribbon resin black (k) panel as specified by selected options. Click and drag the corners and the sides of an area to change size and location of area. The horizontal, vertical, and X, Y coordinates update accordingly. Up to five areas can be added for the K-Panel. Field Front/Back Description Specify the side of the card to apply the area definition. Print All Black with K Panel Define the Overlay or Print Area. Full Card: Select this option to print the resin black (K) panel for all black found within all areas of the image. Defined Area(s): To print the resin black (K) panel in the selected and defined area(s). Undefined Area(s): To print the resin black (K) panel in the space outside the selected and defined area. Print YMC under K Print all black in the designated defined/undefined areas, with the Yellow (Y), Magenta (M) and Cyan (C) ribbon panels directly beneath the resin black (K) Panel. Select this option if printing resin black text or barcodes onto a colored background to provide a more gradual transition between the two. Print K Only Print all black in the designated defined/undefined areas only with resin black, or to print resin black onto a white background to maximize the sharpness of printed text and barcodes. November 2015 PLT-02496, Version: 1.0 Page 3-20 Printing Preferences 3.9 Printer Info Tab The Printer Info tab displays information about the printer Ribbon, Film, Laminate (Cartridge 1), and Laminate (Cartridge 2). Group or Field Ribbon Printer Description Indicates Ribbon Type, Reorder Number and remaining level. Indicates the Printer Card Count Serial Number Version Number PLT-02496, Version: 1.0 November 2015 Chapter 4 ToolBox The ToolBox is located on the DTC5500LMX Card Printer Printing Preferences, Card tab. See Section 3.1: Card Tab for more information. November 2015 PLT-02496, Version: 1.0 ToolBox Page 4-2 4.1 Configuration Tab When ToolBox is selected on the Card tab this is the default screen that opens. See Section 3.1: Card Tab for more information. Field Optional Printer Features Description Automatically Detect Features that are Installed in your Printer:
If selected the driver retrieves the installed printer features information from the firmware and automatically checks the appropriate options. The features are read-only and cannot be updated. If selected and no printer or modules are found, an error message is displayed. If this option is not selection, the user will select the options included in the printer. Event Monitoring This option enables the monitoring of events, and will notify the user when attention is required. Set Language Allows the user to set the printer display language from the pull-down list. OK Cancel Help Closes the window and saves the configuration changes made. Closes the window and cancels any configuration changes made. Opens the Help for this window. PLT-02496, Version: 1.0 November 2015 Page 4-3 ToolBox 4.2 Calibrate Laminator Tab The Calibrate Laminator tab is active when the laminator is automatically detected or when the laminator is manually checked as a feature on the Configuration tab. Note: The lamination module must be warm before calibrating. Calibration may also be performed from the printer LCD. See Section 3.10.2: Sensor Calibration Options. To Calibrate the Laminator:
1. Ensure that the cartridges are out of the Laminator. 2. Ensure the Laminator cover is closed. 3. Click Calibrate. November 2015 PLT-02496, Version: 1.0 ToolBox Page 4-4 4.3 Calibrate Ribbon Tab To Calibrate the Ribbon:
1. Take out the ribbon drawer and remove the ribbon. 2. Reinsert the empty ribbon drawer. 3. Click Calibrate. 4. After calibration has completed, take out the ribbon drawer and reinstall the ribbon. Reinsert the ribbon drawer into the printer. 5. The printer will beep twice if the procedure was successful, once if the procedure failed. 6. Click the OK button to complete the procedure. Note: Calibration may also be performed from the printer LCD. See Section 3.10.2: Sensor Calibration Options. PLT-02496, Version: 1.0 November 2015 Page 4-5 ToolBox 4.4 Clean Printer Tab To Clean the Printer:
1. Remove all cards from the Card Hopper. 2. Take out the ribbon drawer and remove the ribbon. 3. Reinsert the empty ribbon drawer. 4. Remove the paper backing from both sides of the Cleaning Card. Note: DO NOT remove small liner strip if a magnetic encoding module is installed in your printer. Insert the Cleaning Card into the Card Hoppers in-feed rollers. See the diagram below. 5. 6. Click the Clean button. 7. Guide the Cleaning Card into the printer if necessary. 8. When the Cleaning routine is complete, the Cleaning Card will exit the printer. 9. Take out the ribbon drawer and reinstall the ribbon. 10. Reinsert the ribbon drawer into the printer. Note: The cleaning routine will begin after all current print jobs have completed. Cleaning can also be completed through the printer LCD screen. See Section 3.10: Tools Menu. November 2015 PLT-02496, Version: 1.0 ToolBox Page 4-6 4.5 Advanced Settings Tab Use the Advanced Settings tab for adjusting the internal printer settings. These settings have been customized for every printer at the factory. Note: Any changes affect settings for the firmware. To modify a Setting, click on the numeric value in the cell, click the up/down arrow to modify the value, or select the value and type a new value. Field Setting Default Current Apply Description This column displays the name of the Setting. This column displays default value for the Setting. This column displays current value for the Setting. Applies the changed values. Restore Defaults Restores the default values. Enable Mag Verify Select this option to verify that the data is written to the tracks correctly. PLT-02496, Version: 1.0 November 2015 Page 4-7 ToolBox 4.5.1 Settings Information Setting Head Resistance Print Left of Form Image Darkness Print Top of Form Mag Top of Form Description This is factory set. If the main board or the printhead is replaced then adjust this number. Locate the printhead setting number on the bottom of the printhead. The number reads R=XXXX. Use this option to adjust the vertical position of the printed image on the card; so it appears centered. Maximum Adjustment Range is +/- 127. Each increment equals .01. Use this option to set the overall darkness of the printed image by increasing or decreasing the amount of heat (used by the Printhead when printing). Note: If the value is set too high, the Ribbon may jam or even break. Use this option to adjust the length-wise or horizontal position of the printed image on the card (so it appears to be centered). Note: If the negative value is set too high, the Print Ribbon may break. Use this option to shift the starting point where the Printer begins to encode the magnetic track data on the cards Magnetic Stripe. Note: If the negative value is set too high, the Printer may start encoding before the Magnetic Stripe reaches the encoding head. Maximum adjustment range is +/- 80. Each increment equals .01. Ribbon Print Tension Use the Ribbon Tension option to increase or decreases the amount of tension
(drag) on the Ribbon during printing. Ribbon Calibrate Green This is a calibration driven value and should not be adjusted. Note: This is factory set and should not be changed unless directed by a technician. Resin Heat Adjust Use this adjustment for Black premium resin text and barcodes if they appear faded, too light or too dark. Maximum Adjustment Range is +/- 100. Note: This control can be helpful for fine-tuning the transfer of resin text and bar codes. Sleep Time The Sleep Time setting adjusts the number of minutes of inactivity before the Printer enters a low power sleep state. OLED Contrast
(Display Contrast) Use this option to increase or decrease the contrast of the printer OLED (if applicable). Ribbon Calibrate Blue This setting is a calibration driven value and should not be adjusted. Note: This is factory set and should not be changed unless directed by a technician. Cleaning Rate Use this option to adjust the number of cards printed before the Printer displays a message indicating cleaning is needed. The default value is 3000 cards. Mag HI-Co Voltage Offset This setting is a calibration driven value and should not be adjusted. Note: This is factory set and should not be changed unless directed by a technician. November 2015 PLT-02496, Version: 1.0 ToolBox Page 4-8 Setting Mag Lo-Co Voltage Offset Ribbon Green LED Level Ribbon Blue LED Level Description This setting is a calibration driven value and should not be adjusted. Note: This is factory set and should not be changed unless directed by a technician. This setting is a calibration driven value and should not be adjusted. Note: This is factory set and should not be changed unless directed by a technician. This setting is a calibration driven value and should not be adjusted. Note: This is factory set and should not be changed unless directed by a technician. PLT-02496, Version: 1.0 November 2015 Chapter 5 Troubleshooting 5.1 System Overview Knowing the sequence of the printer operation helps when troubleshooting the printer. Troubleshooting utilizes the printer error buttons, error messages and printer-specific tools. 5.1.1 Sequence of Operations 1. File information is received from the PC. 2. Printer compares the installed ribbon type stored in memory with the ribbon type command that was sent from the printer. If the ribbon type does not match, the Pause button (on the right) flashes. 3. The print stepper motor engages. 4. The card feed sensor detects the leading edge of the card and the headlift stepper engages to disengage the input lever. 5. The card feeds through for the alignment pass. 6. The card feed stepper motor engages to queue card for magnetic encoding (if applicable). 7. The encoded data is written to the card (if applicable). 8. The magnetic encoder verifies while the stepper reverses the card (if applicable).The print ribbon drive engages (if not already at the yellow panel). 9. The print ribbon sensor looks for the yellow panel. Note: The print ribbon encoder detects the number of revolutions required to use an entire color panel. 10. The print stepper motor engages. 11. The card feed sensor detects the leading edge of card. 12. The print stepper motor queues card to the middle of the platen roller. All stop. 13. The print headlift motor engages to the print position. 14. The print cover sensor checks for closed state. 15. The print stepper motor engages. 16. The ribbon drive motor engages. 17. The image data is burned by the printhead until the image data is depleted. All Stop. 18. The thermistor engages the printhead cooling fan to maintain proper operating temperature. 19. The headlift motor engages to the queue position. 20. The print stepper motor engages. 21. The print ribbon drive engages. November 2015 PLT-02496, Version: 1.0 Troubleshooting Page 5-2 22. After ribbon advances a few encoder clicks, assume the ribbon is free of card. All stop. 23. Repeat Steps 9 through 22 for the appropriate number of color/overlay Panels. 24. Either the card is ejected from the singled-sided printer or the card feed stepper engages to queue the card for the flipper table for the dual-sided printer. 25. All stop. 5.2 Printer Error Buttons The DTC5500LMX uses both button messages and message display. The display message system appears as a graphical message, for example:
5.2.1 Printer Error Button and On-screen Messages 26. The Pause (
) button illuminates blue when the printer is capable of accepting a print job and is not in an error state. This button LED will continue to stay on while the printer prints as long as there is no error. This button LED will also be dimmed when the printer goes into Sleep mode.When an error occurs, the Pause (
) button no longer illuminates blue but blinks red. 27. Press the Pause (
) button when printer is in an error state to cause the printer to retry. Note: The button illuminates as blue and retries the failed action. When downloading an upgrade file, both buttons are blue and blink. 28. If a language (other than English) is currently selected, you can press and hold the Pause
(
) button during the power-up sequence to change the language back to English. 29. If no printer display is available, press or hold the buttons to access some internal tests. To print a card with the Printer Settings, press the Pause (
when the printer is ready and idle. To print the Alignment or the Self Test, press and hold the Pause (
power-up sequence.
) button and hold for 4+ seconds
) button during the 5.2.2 Error Messages When an error occurs in the printer, the PC shows the error message on screen with solutions. The display blinks in the location requiring attention. Locations can include the printer, input hopper, magnetic encoder, flipper, card path, ribbon, and data/communication device error. Each table uses a 3-column presentation to display a specific or printer error message, its cause and its solution. PLT-02496, Version: 1.0 November 2015 Page 5-3 Troubleshooting This format allows the troubleshooter to identify the error and its cause, and then perform the procedure provided in the solution column. This standard mode of identifying the problem and its solution should provide an efficient method of troubleshooting this printer If you encounter problems beyond the capabilities of this error message table, you should contact Technical Support. Example of an Error Message:
Error Message Cause Solution
# 81 Unable to Feed The printer is unable to feed a card from the input card hopper. Check the following, then press the Pause button to continue. Verify the card thickness setting is set to the thickness of your cards. Verify the Cleaning roller is properly installed on the Ribbon Cartridge. Check for card slippage. If necessary, run the Printer cleaning routine. Verify that your cards are within the accepted card size range. Verify the cards are not sticking together. November 2015 PLT-02496, Version: 1.0 Troubleshooting Page 5-4 5.2.3 Troubleshooting with the Error Message Table Error Message Cause Solution
# 2 Head Move Error The printhead lift has malfunctioned.
# 8 Head Sensor Error The printhead temperature sensor is not functioning or is not connected properly. Or, the printhead is not cooling properly. Reset the printer and try again. If this problem persists, call for technical assistance. Reset the printer and try again. If the problem persists, call for technical assistance.
# 9 Reboot Required An unspecified system error has been detected by the printer firmware. Reset the printer and try again. If this problem persists, call for technical assistance.
# 25 Ribbon not Installed No ribbon is installed in the printer. Install a ribbon and retry.
# 30 Mag Verify Error Magnetic encoding verification has failed. Try encoding with a different card. Verify cards have the magnetic stripe. Replace the magnetic encoding module.
# 31 No Mag Module
# 38
# 39
# 40 EEPROM Corrupt EEPROM Read Error
# 44 Flipper Jam/
Home Error
# 45 No Flip Module installed
# 60 Laminator Calibration Fail The printer is not configured with the encoder data type that you are trying to send. Ensure that no encoding data is being sent with the print job and reprint the card. Install a magnetic encoding module. EEPROM is restored with factory default values. A card has become jammed in the printers flipper table. The flipper failed to position properly while aligning a card or flipping a card. Request to print on 2nd side of card, but no flipper is installed. If changes were made in the Advanced Settings tab in the printer driver, click the Default button to reset these numbers. Reset the printer and try again. If this problem persists, call for technical assistance. Clear any cards in the flipper table using the buttons to move the card out. Resume printing. The flipper table should be level when the printer is powered up. If the flipper Table is at an angle, open the card output door and manually level it. Then cycle the printer power to reset. Reset the printer and retry. If problem persists call for technical assistance. If a Flipper Module is present, ensure that the Print Both Sides option in the printer driver is set correctly. Install a flipper module. LED calibration error occurred. Try again. PLT-02496, Version: 1.0 November 2015 Page 5-5 Troubleshooting Error Message Cause Solution
# 64
# 65
# 66 Reboot Required
# 67 General
# 68 Card in Printer Unspecified system error detected by the printer firmware. Reset the printer and try again. If this problem persists, call for technical assistance. Utility command does not exist. Verify the command and reenter. A card is jammed in the print station or card flipping area of the Printer.
# 70 Multiple Feed Multiple cards were fed into the printer.
# 81 Unable to Feed The printer is unable to feed a card from the input card hopper.
# 82 Mag Jam A card is jammed magnetic station
# 91 Ribbon Out The print ribbon has run out.
# 93 Wrong Ribbon The print ribbon installed in the printer does not match the ribbon type selected in the printer driver.
# 97 Ribbon Search Error The ribbon is not able to find the next panel correctly. Check for jams/breaks. Clear the jam and press the Pause button. Verify the card thickness is set to the thickness of your cards, then press the Pause button. Check for card slippage. If necessary, run the printer cleaning routine Verify the cleaning roller is properly installed on the ribbon cartridge. Verify the cards are not sticking together. Check the following, then press the Pause button to continue. Verify the card thickness setting is set to the thickness of your cards. Verify the Cleaning roller is properly installed on the Ribbon Cartridge. Check for card slippage. If necessary, run the Printer cleaning routine. Verify that your cards are within the perimeters accepted card size range. Verify the cards are not sticking together. Clear any cards in the magnetic station using the buttons to move the card out. Press the Pause button to continue. Install a new ribbon. Press the Pause button to continue or the ON/OFF button to cancel. Change either the installed print ribbon or the ribbon type selected in the printer driver. Press the Pause button to continue or the ON/OFF button to cancel. Recalibrate the ribbon sensor. If broken, repair by taping the ribbon back on to the take- up core. Replace the ribbon. Press the Pause button to continue or the ON/OFF button to cancel. November 2015 PLT-02496, Version: 1.0 Troubleshooting Page 5-6 Error Message Cause Solution
# 99 Ribbon Error The print ribbon has either broken or jammed.
# 100 Ribbon RFID Error There is no ribbon or the ribbon tag information is corrupted or incorrect. If jammed, clear the jam. If broken, repair by taping the ribbon back on to the take- up core. Press the Pause button to continue or the ON/OFF button to cancel. Verify the printer driver settings for correct Ribbon. Try a new ribbon and continue. Press the ON/OFF button to cancel.
# 102
# 103
# 104
#3 Headlift Error
# 106 Job Data Error
# 107 Printing Error
# 109
# 113 Ribbon Release Error
# 110 Card Jam/Align error
# 111 Head Loading
# 112 Card Jam/Align error
# 128
# 170 Calibrate Ribbon
# 129 General This is a problem with the printhead Lift. Reset the printer and try again. If this problem persists, call for technical assistance. The print data sent to the printer is corrupt or has been interrupted. Check the interface cable. Select the ON/OFF button to cancel this print job and then resend the job. An error was detected during printing. Reset the printer and try again. If this problem persists, call for technical assistance. The printer cannot locate the next ribbon panel in order to release the ribbon from the card. A card is jammed in the print station or card flipping area of the printer. Ensure that the ribbon is not stuck to the card. Replace the ribbon. Recalibrate the ribbon sensor. If the ribbon is broken, repair by taping the ribbon back onto the take- up core and manually advance to the next panel. Press the Pause button to continue. Clear the jam. Press the Pause button to continue. An unrecoverable error has occurred during printing. Reset the printer and try again. If this problem persists, call for technical assistance. A card is jammed in the print station or card flipping area of the Printer. Clear the jam. Press the Pause button to continue. The print ribbon sensor is out of calibration or has failed. Calibrate the ribbon sensor. Check for material blocking sensor and try again. Utility command input error has occurred. Verify the command and reenter. PLT-02496, Version: 1.0 November 2015 Page 5-7 Troubleshooting Error Message Cause Solution
# 131 Flipper Jam/Home Error
# 136 Secure Guard Print Disabled
# 139 Please Remove Ribbon
# 144 EEPROM Corrupt EEPROM Read Error
# 202 Encoder Not Installed
# 266 Calibration Failed
# 286 General
# 303 Job Too Large for Multiple Copies
# 306 Laminator Clean Fail Error Message A card has become jammed in the printers flipper table. The flipper failed to position properly while aligning a card or flipping a card. Clear any cards in the flipper table, using the buttons to move the card out. Resume printing. Reset the printer and retry. If problem persists call for technical assistance. Printing is disabled by SecureGuard until a password is received. Reset the printer and retry. If the problem persists, call for technical assistance. Ribbon needs to be removed. Reset the printer and retry. If problem persists, call for technical assistance. EEPROM restored with factory default values. If changes were made in the Advanced Setting tab in the printer driver, click the Default button to reset these numbers. Reset the printer and try again. If this problem persists, call for technical assistance. You are trying to send encoding data, but the Printer is not configured with this Encoder type. iCLASS, Prox, MIFARE, SmartCard Laminator is too cold to calibrate. Reboot the printer or perform a lamination Ensure that no encoding data is being sent with the print job and reprint the card. Install an encoding module. sample. Not used. Job is too big. Send a smaller job. Laminator clean cycle failed. Try again. Cause Solution
# 2 Head Move Error The printhead lift has malfunctioned.
# 8 Head Sensor Error The printhead temperature sensor is not functioning or is not connected properly. Or, the printhead is not cooling properly. Reset the printer and try again. If this problem persists, call for technical assistance. Reset the printer and try again. If the problem persists, call for technical assistance.
# 9 Reboot Required An unspecified system error has been detected by the printer firmware. Reset the printer and try again. If this problem persists, call for technical assistance. November 2015 PLT-02496, Version: 1.0 Troubleshooting Page 5-8 Error Message Cause Solution
# 25 Ribbon not Installed No ribbon is installed in the printer. Install a ribbon and retry.
# 30 Mag Verify Error Magnetic encoding verification has failed. Try encoding with a different card. Verify cards have the magnetic stripe. Replace the magnetic encoding module. The printer is not configured with the encoder data type that you are trying to send. Ensure that no encoding data is being sent with the print job and reprint the card. Install a magnetic encoding module. EEPROM is restored with factory default values. A card has become jammed in the printers flipper table. The flipper failed to position properly while aligning a card or flipping a card. Request to print on 2nd side of card, but no flipper is installed. If changes were made in the Advanced Settings tab in the printer driver, click the Default button to reset these numbers. Reset the printer and try again. If this problem persists, call for technical assistance. Clear any cards in the flipper table using the buttons to move the card out. Resume printing. The flipper table should be level when the printer is powered up. If the flipper Table is at an angle, open the card output door and manually level it. Then cycle the printer power to reset. Reset the printer and retry. If problem persists call for technical assistance. If a Flipper Module is present, ensure that the Print Both Sides option in the printer driver is set correctly. Install a flipper module. Unspecified system error detected by the printer firmware. Reset the printer and try again. If this problem persists, call for technical assistance.
# 31 No Mag Module
# 38
# 39
# 40 EEPROM Corrupt EEPROM Read Error
# 44 Flipper Jam/
Home Error
# 45 No Flip Module installed
# 64
# 65
# 66 Reboot Required
# 68 Card in Printer A card is jammed in the print station or card flipping area of the Printer.
# 70 Multiple Feed Multiple cards were fed into the printer. Clear the jam and press the Pause button. Verify the card thickness is set to the thickness of your cards, then press the Pause button. Check for card slippage. If necessary, run the printer cleaning routine Verify the cleaning roller is properly installed on the ribbon cartridge. Verify the cards are not sticking together. PLT-02496, Version: 1.0 November 2015 Page 5-9 Troubleshooting Error Message Cause Solution
# 81 Unable to Feed The printer is unable to feed a card from the input card hopper.
# 82 Mag Jam A card is jammed magnetic station
# 91 Ribbon Out The print ribbon has run out.
# 93 Wrong Ribbon The print ribbon installed in the printer does not match the ribbon type selected in the printer driver.
# 97 Ribbon Search Error The ribbon is not able to find the next panel correctly. Check for jams/breaks.
# 99 Ribbon Error The print ribbon has either broken or jammed.
# 100 Ribbon RFID Error There is no ribbon or the ribbon tag information is corrupted or incorrect. Check the following, then press the Pause button to continue. Verify the card thickness setting is set to the thickness of your cards. Verify the Cleaning roller is properly installed on the Ribbon Cartridge. Check for card slippage. If necessary, run the Printer cleaning routine. Verify that your cards are within the perimeters accepted card size range. Verify the cards are not sticking together. Clear any cards in the magnetic station using the buttons to move the card out. Press the Pause button to continue. Install a new ribbon. Press the Pause button to continue or the ON/OFF button to cancel. Change either the installed print ribbon or the ribbon type selected in the printer driver. Press the Pause button to continue or the ON/OFF button to cancel. Recalibrate the ribbon sensor. If broken, repair by taping the ribbon back on to the take- up core. Replace the ribbon. Press the Pause button to continue or the ON/OFF button to cancel. If jammed, clear the jam. If broken, repair by taping the ribbon back on to the take- up core. Press the Pause button to continue or the ON/OFF button to cancel. Verify the printer driver settings for correct Ribbon. Try a new ribbon and continue. Press the ON/OFF button to cancel.
# 102
# 103
# 104
#3 Headlift Error
# 106 Job Data Error This is a problem with the printhead Lift. Reset the printer and try again. If this problem persists, call for technical assistance. The print data sent to the printer is corrupt or has been interrupted. Check the interface cable. Select the ON/OFF button to cancel this print job and then resend the job. November 2015 PLT-02496, Version: 1.0 Troubleshooting Page 5-10 Error Message Cause Solution
# 107 Printing Error An error was detected during printing. Reset the printer and try again. If this problem persists, call for technical assistance. Ensure that the ribbon is not stuck to the card. Replace the ribbon. Recalibrate the ribbon sensor. If the ribbon is broken, repair by taping the ribbon back onto the take- up core and manually advance to the next panel. Press the Pause button to continue. Clear the jam. Press the Pause button to continue. The printer cannot locate the next ribbon panel in order to release the ribbon from the card. A card is jammed in the print station or card flipping area of the printer. An unrecoverable error has occurred during printing. Reset the printer and try again. If this problem persists, call for technical assistance. A card is jammed in the print station or card flipping area of the Printer. Clear the jam. Press the Pause button to continue. The print ribbon sensor is out of calibration or has failed. Calibrate the ribbon sensor. Check for material blocking sensor and try again. A card has become jammed in the printers flipper table. The flipper failed to position properly while aligning a card or flipping a card. Clear any cards in the flipper table, using the buttons to move the card out. Resume printing. Reset the printer and retry. If problem persists call for technical assistance. Printing is disabled by SecureGuard until a password is received. Reset the printer and retry. If the problem persists, call for technical assistance. Ribbon needs to be removed. Reset the printer and retry. If problem persists, call for technical assistance. EEPROM restored with factory default values. You are trying to send encoding data, but the Printer is not configured with this Encoder type. iCLASS, Prox, MIFARE, SmartCard If changes were made in the Advanced Setting tab in the printer driver, click the Default button to reset these numbers. Reset the printer and try again. If this problem persists, call for technical assistance. Ensure that no encoding data is being sent with the print job and reprint the card. Install an encoding module.
# 109
# 113 Ribbon Release Error
# 110 Card Jam/Align error
# 111 Head Loading
# 112 Card Jam/Align error
# 128
# 170 Calibrate Ribbon
# 131 Flipper Jam/Home Error
# 136 Secure Guard Print Disabled
# 139 Please Remove Ribbon
# 144 EEPROM Corrupt EEPROM Read Error
#202 Encoder not installed PLT-02496, Version: 1.0 November 2015 Page 5-11 Troubleshooting 5.2.4 Printer-Specific Tools The status icons are as follows:
This icon indicates that the print ribbon supply is low and will require replacement soon. The entire ribbon cartridge must be replaced. This icon indicates that the printer needs to be cleaned. This icon is only displayed for printers with an attached dual-input card hopper and indicates that the top input hopper is currently selected. This icon is only displayed for printers with an attached dual-input card hopper and indicates that the bottom input hopper is currently selected. Press the button to scroll through the details of the printer and perform the action. Press the button to select the option. When and Languages and Exit. is selected, use the left down arrow to scroll through the Info, Test Prints, Use the corner arrow to run that option. The curved arrow will return to the first screen. November 2015 PLT-02496, Version: 1.0 Troubleshooting Page 5-12 5.2.4.1 Additional Printer Specific Tools Label Description Printer Type Firmware Version IP Address Flipper Lamination Magnetics E-Card Password Card count Color Photo: Select this choice to print a color card to test communication and integrity. Alignment: Select this choice to print a card used to align the print image on the card. Settings: Select this choice to print a card with the Advanced settings. Resin: Select this choice to print a RESIN test card. Rewritable: Select this choice to ERASE the Rewritable card. Magnetic: Select this choice to test Magnetic encoding (Hi-Co only) Lamination: Select this choice to laminate a test card. Select the hopper to input cards. Applies to dual-hopper printers. Clean Printer: Select this choice to run the clean printer routine. Clean Laminator: Select this choice to run the clean laminator routine. Calibrate Mag: Select this choice to calibrate the Magnetic Sensor. Calibrate Rib Sensor: Select this choice to calibrate the ribbon sensor. Network: Select this to choice configure network options Select this choice to change the Printer Displayed Language. Select this choice to exit the Printer Tool options. INFO TEST PRINTS Hopper Select ToolBox Language Exit PLT-02496, Version: 1.0 November 2015 Chapter 6 Firmware Upgrades 6.1 Upgrade Information To upgrade the printers firmware, perform the following steps:
1. Run the FARGO Workbench Card Printer Utility. 2. If running FARGO Workbench Version 3 or greater:
a. Select the Update Manager utility. b. Select the printer(s) to update. c. Select the Select Firmware file option to locate or enter the latest firmware file
(i.e. FRW-00373_DTC100_v2.3.3.20.frm). d. Locate the firmware file and click Open. e. Click Begin Updating Firmware to send the file to the printer(s). 3. If running a FARGO Workbench release prior to Version 3:
a. Select the Application Menu at the upper left and select Upgrade Firmware. b. Enter the firmware file name or click Browse to find and select the latest firmware file (i.e. FRW-00373_DTC100_v2.3.3.20.frm). c. Click OK to send the file to the printer(s). 4. Restart the printer if it does not restart automatically. November 2015 PLT-02496, Version: 1.0 Firmware Upgrades Page 6-2 This page intentionally left blank. PLT-02496, Version: 1.0 November 2015 Chapter 7 Technical Support 7.1 Technical Support This section provides you with an efficient, step-by-step procedure to be used when contacting HID Global Technical Support, as needed, for this card printer. Contact the HID Global Technical Support Group by phone at (866)607-7339 Ext #6 or by fax at
(952) 946-8492 for additional technical assistance. OR Contact HID Technical Support. Position a phone near the printer and computer so the Technician can help to troubleshoot the printer. Please have a self-test and a sample card ready when calling HID Technical Support. 7.1.1 Reading the Serial Numbers on a FARGO Printer You can determine when your card printer was manufactured by reading directly from the serial number (affixed to your card printer). Example: Serial Number B2050028 (2012) B2050028: The first two digits in the serial number indicate the year the printer was built (e.g., the digits B2 indicate the year 2012). B2050028: The third and fourth digits in the serial number indicate the week the printer was built
(e.g., the digits 05 indicate week 5 of that year). B2050028: The last four digits indicate the sequence number for the numeric order in which the printers were built. November 2015 PLT-02496, Version: 1.0 Technical Support Page 7-2 This page intentionally left blank. PLT-02496, Version: 1.0 November 2015 Revision History Date Description November 2015 Initial release. Page 12-i Document Version 1.0 June 2015 PLT-01485, Version: 2.2 hidglobal.com
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2016-03-29 | 13.56 ~ 13.56 | DXX - Part 15 Low Power Communication Device Transmitter | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2016-03-29
|
||||
1 | Applicant's complete, legal business name |
HID Global Corporation
|
||||
1 | FCC Registration Number (FRN) |
0005004122
|
||||
1 | Physical Address |
611 Center Ridge Dr.
|
||||
1 |
Austin, Texas 78753
|
|||||
1 |
United States
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
t******@siemic.com
|
||||
1 | TCB Scope |
A1: Low Power Transmitters below 1 GHz (except Spread Spectrum), Unintentional Radiators, EAS (Part 11) & Consumer ISM devices
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
JQ6
|
||||
1 | Equipment Product Code |
X002100
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
R****** C******
|
||||
1 | Title |
Compliance Engineering Manager
|
||||
1 | Telephone Number |
303-4********
|
||||
1 | Fax Number |
303-4********
|
||||
1 |
r******@hidglobal.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DXX - Part 15 Low Power Communication Device Transmitter | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Color Card Printer | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Single Modular Approval | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
SIEMIC Labs
|
||||
1 | Name |
L******** B******
|
||||
1 | Telephone Number |
40852********
|
||||
1 |
l******@siemic.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 13.56000000 | 13.56000000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC