all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 2 |
|
User Manual | Users Manual | 2.77 MiB | ||||
1 2 | Cover Letter(s) | |||||||
1 2 | External Photos | |||||||
1 2 | Internal Photos | |||||||
1 2 | ID Label/Location Info | |||||||
1 2 | Test Setup Photos | |||||||
1 2 | Test Report | |||||||
1 2 | Cover Letter(s) |
1 2 | User Manual | Users Manual | 2.77 MiB |
instalacin installation instalao installation installazione iCLASS INSTALLATION GUIDE RK40 RWK400 RPK40 13.56 MHz Contactless Smart Card Readers with Keypad 6404-901 A.1 iCLASS RK40, RWK400, RPK40 6404-901 A.1 Parts List PARTS 1 - iCLASS Reader 1 - Installation Manual 2 - 3.5 mm x .6 pitch x 12 mm Phillips machine screws 3 - #6-32 x .375 Phillips self-tapping (mv) machine screws 2 - #6 x 1.5 Phillips sheet metal screws 1 - #6 x .375 Spanner security screw, anti-tamper 2 - Terminal connectors for terminal readers 1 - Mounting Gasket 1 - Base plate Recommended Up to 9 wire splices (pigtail) Cable, 5-9 conductor (Wiegand or RS232), 22 or 24 AWG [65 mm or 51 mm] (pigtail) Linear DC Power supply Metal or plastic junction box Security Tool (for anti-tamper screw) HID 04-0001-03 LiSTA de comPonenTeS 1 lector iCLASS 1 manual de instalacin 2 tornillos mecnicos Phillips de 3.5 mm x 12 mm, paso 0.6 3 tornillos mecnicos autoperforantes N. 6 de 32 x 0.375 2 tornillos Phillips N. 6 para metales de 1.5 1 tornillo de seguridad N. 6 contra sabotaje de 0.375 para llave inglesa 2 conectores de borne para lectores de borne 1 guarnicin de montaje 1 placa base Recomendado:
Un mximo de 9 empalmes para cable (flexible) Cable, de 5 a 9 conductores (Wiegand o RS232), 22 o 24 AWG
[65 mm o 51 mm] (flexible) Fuente de alimentacin lineal de CC Caja metlica o de plstico para conexiones Herramienta de seguridad (para tornillo contra sabotaje) HID 04-0001-03 LiSTe deS PiceS 1 - Lecteur iCLASS 1 - Manuel dinstallation 2 - Vis mcaniques cruciformes 3,5 mm x 0,6 pas x 12 mm 3 - Vis mcaniques cruciformes autotaraudeuses N 6-32 x 0,375 pouce 2 - Vis tle cruciformes N 6 x 1,5 pouce 1 - Vis de scurit inviolable N 6 x 0,375 pouce 2 - Connecteurs de bornier pour lecteurs bornier 1 - Joint plat 1 - Support Recommands Jusqu 9 embouts de cble (en tire-bouchon) Cble, 5-9 conducteurs (Wiegand ou RS232), 22 ou 24 AWG [65 mm ou 51 mm] (cble) Alimentation cc linaire Botier de jonction mtallique ou plastique Outil de scurit (pour vis inviolable) HID 04-0001-03 1 - iCLASS 1 2 - 3.5 mm x .6 x 12 mm Phillips 3 - #6-32 x .375 Phillips (mv) 2 - #6 x 1.5 Phillips 1 - #6 x .375 2 -
1 -
1 -
9 5-9 Wiegand RS23222 24 AWG
[65 mm 51 mm]
HID 04-0001-03 componentes pices peas Komponenten componenti passo 0,6 x 12 mm PeAS 1 Leitor iCLASS 1 Manual de instalao 2 Parafusos Phillips para aplicao a mquina de 3,5 mm x de 3 Parafusos Phillips de auto-rosqueamento para aplicao a mquina n 6-32 x 0,375 pol. 2 Parafusos Phillips de chapa metlica n 6 x 1,5 pol. 1 Parafuso de segurana de chave de porca n 6 x 0,375 pol., 2 Conectores do terminal para os leitores do terminal. 1 Vedao de montagem 1 Placa bsica Recomendado Entrelaamentos de at 9 cabos (cabo flexvel) Cabo, condutor 5-9 (Wiegand ou RS232), 22 ou 24 AWG antiviolao
[65 mm ou 51 mm] (cabo flexvel) Alimentao DC linear Caixa de juno de metal ou plstico Ferramenta de segurana (para o parafuso antiviolao) HID 04-0001-03 komPonenTen 1 iCLASS Leser 1 Installationsanleitung 2 Kreuzschlitzschrauben 3,5 mm x 12 mm (x 0,6 Zoll Teilung) 3 Kreuzschlitz-Schneidschrauben US-Gre Nr. 6-32 x 0,375 Zoll 2 Kreuzschlitz-Blechschrauben US-Gre Nr. 6 x 1,5 Zoll 1 Sicherungsschraube US-Gre Nr. 6 x 0,375 Zoll 2 Anschlussstecker fr Leser 1 Montagedichtung 1 Grundplatte Empfohlene Komponenten Bis zu 9 Spleiverbindungen Kabel, 5-9 Leiter (Wiegand oder RS232), 22 oder 24 AWG
[65 mm oder 51 mm], (bewegliches Anschlusskabel) Lineares Gleichstromnetzteil Verteilerkasten aus Metall oder Kunststoff Sicherungswerkzeug (fr Sicherungsschraube) HID 04-0001-03 eLenco PARTi Un lettore iCLASS Un manuale di installazione Due viti da ferro Phillips da 3,5 mm x 12 mm con passo da 0,6 Viti da ferro autofilettanti Phillips numero # 6 32 x 0,375 pollici Due viti per lamiera Phillips numero 6 x 1,5 pollici Una vite di sicurezza antimanomissione Spanner numero 6 x 0,375 pollici Due morsettiere per terminali lettore Una guarnizione per montaggio Una piastra di base Consigliati Cavo a nove poli Cavo, conduttore 5-9 (tipo Wiegand o RS232), 22 o 24 AWG [65 mm o 51 mm] (a tortiglione) Alimentatore lineare c.c. Scatola di giunzione metallica o in plastica Utensile di sicurezza (per viti antimanomissione) HID 04-0001-03 1 - iCLASS 1 -
2 - 3.5 mm x .6 x 12 mm 3 - #6-32 x .375 (mv 2 - #6 x 1.5 1 - #6 x .375 2 -
1 -
1 -
9 59(Wiegand RS232)2224 AWG
[65 mm51 mm] () DC HID 04-0001-03 1 - iCLASS 1 -
2 - 3.5 mm x 0.6 x 12 mm (+) 3 - #6-32 x 0.375 (+) 2 - #6 x 1.5 (+) 1 - #6 x 0.375 , -
2 -
1 -
1 -
9 (Pigtail)
, 5-9 (Wiegand RS232), 22 24 AWG[65 mm 51 mm] (Pigtail) Linear DC
(- ) HID 04-0001-03 1 (-) iCLASS 1 2 3,5 x 0,6 x 12 3 - #6-32 x 0,375 2 6 x 1,5 1 6 x 0,375 2 1 1
9 5-9 (Wiegand RS232), 22 24 AWG
[65 51 ] ( )
( ) HID 04-0001-03 2 INSTALLATION GUIDE 2009 HID Global Corporation. All rights reserved. 6404-901 A.1 Specifications PRODUCT PRODUCTO PRODUIT PRODUTO PRODUKT PRODOTTO BASE PART NUMBER NMERO DE COMPONENTE BASE RFRENCE DE BASE NMERO DAS PEAS BSICAS HAUPTTEILENUMMER NUMERO PARTE DI BASE RK40 6130 / 6138 / 6139 /
6132BxH *** / 6132BxP ***
INPUT VOLTAGE (VDC) TENSIN DE ENTRADA (VCC) TENSION DALIMENTATION (Vcc) VOLTAGEM DE ENTRADA (VCC) EINGANGSSPANNUNG (VDC) TENSIONE IN INGRESSO (V c.c.) CURRENT CORRIENTE COURANT CORRENTE STROMSTRKE CORRENTE
(VDC)
(VDC)
(VDC)
( ) AVG PEAK 95 mA 100 mA RK40, RWK400, RPK40 iCLASS especificaciones spcifications especificaes spezifiKationen specifiche OPERATING TEMPERATURE TEMPERATURA DE FUNCIONAMIENTO TEMPRATURE DE FONCTIONNEMENT TEMPERATURA OPERACIONAL BETRIEBSTEMPERATUR TEMPERATURA DESERCIZIO CABLE LENGTH LONG. DE CABLE UL REF NUMBER NMERO DE REFERENCIA UL LONGUEUR DE CBLE COMPRIMENTO DO CABO COMPRIMENTO DO CABO LUNGHEZZA CAVO RF. UL NMERO DE REFERNCIA UL UL-REFERENZNUMMER NUMERO DI RIFERIMENTO UL UL UL UL UL RWK400 6131 5-16 VDC
* 95 mA 132 mA
-30 - 150F
(-35 - 65 C) RPK40 6136 / 6133 / 6134
** 95 mA 144 mA
(152.4 m) 300 ft - 24 AWG
(91.44 m) Wiegand = 500 ft - 22 AWG RS232 RS485 USB UART
= 50 ft (15.24 m)
= 4000 ft (1,219.2 m)
= 16 ft (4.9 m)
= < 1 ft (0.3 m) RK40Cx1x2N RWK400Cx1x3N RPK40Cx1x4N UL Reference Number Deciphering x1 Reader Colors: K = Black, G = Gray x2 Wiring:
x3 RW Reader Interface:
N = Pigtail, T = Terminal T = RS232, U = USB, B = UART to UART, 4 = RS485 x4 multiCLASS Proximity: N = HID/AWID Prox, D = Indala Prox, X = Prox module not installed montaje montage montagem montage montaggio In addition to Wiegand or Clock-and-Data, RW readers support RS232, RS485, USB, or UART communications.
Note: Cable length over 200 feet may require a larger gauge wire.
*** Not UL listed. USB modules - + 40mA. All other RW modules: + 10 mA. Prox modules - HID Prox: + 16 mA, Indala Prox: + 44 mA, EM Prox: + 35 mA. 1 Mounting Junction box not included. Caja para conexiones no incluida. Botier de jonction non inclus. Caixa de juno no includa. Anschlusskasten nicht mit inbegriffen. Scatola di raccordo non inclusa. 2009 HID Global Corporation. All rights reserved. INSTALLATION GUIDE 3 iCLASS RK40, RWK400, RPK40 6404-901 A.1 2 Wiring BEEP GRN RTN
+VDC SHLD RED HOLD GPI01 GPI02 OC/TMPR DATA1 DATA0 GPI03 GPI04 BEEP GRN RTN
+VDC SHLD RED HOLD GPI01 GPI02 OC/TMPR DATA1 DATA0 GPI03 GPI04 18 in
(0.46 m) BEEPER (YEL) HOLD (BLU) TAMPER (VIO) DATA1 (WHT) DATA0 (GRN) GRN LED (ORN) RED LED (BRN)
+VDC (RED) GND (BLK) SHLD (DR) cableado cblage fiao Verdrahtung cablaggio ATTENTION Observe precautions for handling ELECTROSTATIC SENSITIVE DEVICES Pigtail (RP) Reader Terminal Reader Pigtail Yellow Orange Black Red Drain Brown Blue Terminal Description Beeper Input P1-1 P1-2 P1-3 P1-4 P1-5 P1-6 P1-7 Green (GRN) LED Input Ground (RTN)
+VDC
* Shield (SHLD) Red LED Input Hold Input Pigtail Terminal Description Violet White Green P2-7 P2-6 P2-5 P2-4 P2-3 P2-2 P2-1
GPIO1 (RS232-T / RS485-A / HADP-OSDP-A / USB-5V / UART-T) GPIO2 (RS232-R / RS485-B / HADP-OSDP-B / USB-D+ / UART-R)
*** Open Collector Output
**** Wiegand Data 1 / Clock
**** Wiegand Data 0 / Data
GPIO3 (RS485-Z/USB-D-) GPIO4 (RS485-Y)
Drain wire can be data return line when a separate power supply is used. Excluding multiCLASS (RP Readers), requires Expansion Module [ RS232, RS485, USB, UART to UART ]. GPIO signifies a General Purpose Input/Output. Tamper Output. When activated, output syncs to ground (default).
**** Dependent upon reader configuration. See HTOG Wiegand and Clock-and-Data configurations for more information. Flexible Amarillo Naranja Negro Rojo Drenaje Marrn Azul Borne P1-1 Descripcin Entrada de bper P1-2 P1-3 P1-4 P1-5 P1-6 P1-7 Entrada de LED Verde (GRN) Tierra (RTN)
+VCC
* Blindaje (SHLD) Entrada de LED rojo Entrada de retencin Flexible Violeta Blanco Verde Borne P2-7 P2-6 P2-5 P2-4 P2-3 P2-2 P2-1 Descripcin
GPIO1 (RS232-T / RS485-A/ HADP-OSDP-A / USB-5V / UART-T)
GPIO2 (RS232-R / RS485-B / HADP-OSDP-B / USB-D+ / UART-R) Salida de colector abierto
**** Datos Wiegand 1 / Reloj
**** Datos Wiegand 0 / Datos
GPIO3 (RS485-Z/USB-D-) GPIO4 (RS485-Y) El cable de drenaje puede ser una lnea de retorno de datos cuando se usa una fuente de alimentacin separada. No incluye multiCLASS (lectores RP), requiere mdulo de expansin [RS232, RS485, USB, UART a UART]. GPIO es la sigla en ingls correspondiente a Entrada/Salida de Uso General. Salida de sabotaje. Al activarse, la salida se sincroniza con tierra (predeterminado).
**** Depende de la configuracin del lector. Consulte las configuraciones de HTOG Wiegand y Reloj y datos para obtener ms informacin. 4 INSTALLATION GUIDE 2009 HID Global Corporation. All rights reserved. 6404-901 A.1 RK40, RWK400, RPK40 iCLASS Cble Jaune Orange Noir Rouge Drainage Marron Bleu bornier P1-1 Description Entre Beeper P1-2 P1-3 P1-4 P1-5 P1-6 P1-7 Entre LED verte (GRN) Terre (RTR)
+Vcc
* Blindage (BLIND) Entre LED rouge Entre Hold Cble Violet Blanc Vert bornier P2-7 P2-6 P2-5 P2-4 P2-3 P2-2 P2-1 Description
GPIO1 (RS232-T / RS485-A / HADP-OSDP-A / USB-5V / UART-T)
GPIO2 (RS232-R / RS485-B / HADP-OSDP-B / USB-D+ / UART-R)
*** Sortie collecteur ouvert
**** Donnes Wiegand 1 / Clock
**** Donnes Wiegand 0 / Data
GPIO3 (RS485-Z/USB-D-) GPIO4 (RS485-Y) Le conducteur de drainage peut tre une ligne de renvoi de donnes lors de lutilisation dune alimentation spare. lexception des lecteurs multiCLASS (lecteurs RP), ncessite les modules dextension [RS232, RS485, USB, UART UART]. GPIO est lacronyme de General Purpose Input/Output , cest--dire entre/sortie usage gnral. Sortie autoprotection. Lorsqu'elle est active, la sortie est tire vers la masse (par dfaut).
**** Selon la configuration du lecteur. Pour plus dinformations, voir les configurations HTOG Wiegand et Clock-and-Data. Cabo flexvel Amarelo Terminal P1-1 Descrio Entrada de bper Cabo flexvel Terminal P2-7 Descrio
GPIO1 (RS232-T / RS485-A / HADP-OSDP-A / USB-5V / UART-T) Laranja Preto Vermelho Dreno Marrom Azul P1-2 P1-3 P1-4 P1-5 P1-6 P1-7 Entrada de LED verde (VRD) Terra (RTN)
+VDC
* Proteo (SHLD) Entrada de LED vermelho Manter entrada Violeta Branco Verde P2-6 P2-5 P2-4 P2-3 P2-2 P2-1
GPIO2 (RS232-R / RS485-B / HADP-OSDP-B / USB-D+ / UART-R)
*** Sada do coletor aberta
**** Wiegand-Daten 1/Uhr
**** Dados Wiegand 0 / Dados
GPIO3 (RS485-Z/USB-D-) GPIO4 (RS485-Y) O fio do dreno pode ser uma linha de retorno de dados quando uma alimentao separada utilizada. A excluso do multiCLASS (Leitores RP) requer Mdulo de expanso [ RS232, RS485, USB, UART para UART]. GPIO significa Entrada/sada de uso geral. Sada de tamper. Quando ativada a sada sincroniza com o terra (padro).
**** Dependente da configurao do leitor. Consulte do HTOG Wiegand e Configuraes do Relgio e de Dados para obter mais informaes. Pigtail Gelb Orangefarben Schwarz Rot Erdungsdraht Braun Blau Terminal P1-1 Beschreibung Signaltoneingang P1-2 P1-3 P1-4 P1-5 P1-6 P1-7 Grn (GRN) LED-Eingang Erdungsleiter (RTN)
+VDC
* Abschirmung (SHLD) Eingang rote LED Hold-Eingang Pigtail Violett Wei Grn Terminal P2-7 P2-6 P2-5 P2-4 P2-3 P2-2 P2-1 Beschreibung
GPIO1 (RS232-T / RS485-A / HADP-OSDP-A / USB-5V / UART-T)
GPIO2 (RS232-R / RS485-B / HADP-OSDP-B / USB-D+ / UART-R)
*** Open-Collector-Ausgang
**** Wiegand-Daten 1 / Uhr
**** Wiegand-Daten 0 / Daten
GPIO3 (RS485-Z/USB-D-) GPIO4 (RS485-Y) Bei Verwendung eines separaten Netzteils kann der Erdungsdraht als Datenrcklauf-Leitung dienen. Auer multiCLASS (RP-Leser), erfordert Erweiterungsmodul [RS232, RS485, USB, UART zu UART]. GPIO steht fr General Purpose Input/Output (Allgemein verfgbarer Eingang/Ausgang).
*** Manipulationssicherungsausgang. Bei Aktivierung schaltet der Ausgang auf Erdungsleiter um (Standard).
**** Abhngig von Leserkonfiguration. Weitere Informationen siehe HTOG Wiegand- und Clock-and-Data-Konfiguration. Cavo flessibile Giallo Arancione Nero Rosso Spurgo Marrone Blu Terminale P1-1 Descrizione Ingresso con cicalino Cavo flessibile Terminale P2-7 Descrizione
** GPIO1 (RS232-T / RS485-A / HADP-OSDP-A / USB-5V / UART-T) P1-2 P1-3 P1-4 P1-5 P1-6 P1-7 Ingresso LED verde (GRN) Massa (RTN)
+V c.c.
* Schermatura (SHLD) Ingresso LED rosso Ingresso di tenuta Violetto Bianco Verde P2-6 P2-5 P2-4 P2-3 P2-2 P2-1
** GPIO2 (RS232-R / RS485-B / HADP-OSDP-B / USB-D+ / UART-R)
*** Uscita collettore aperto
**** Wiegand Data 1 / Clock
**** Wiegand Data 0 / Clock
** GPIO3 (RS485-Z/USB-D-)
** GPIO4 (RS485-Y) Il filo di spurgo pu essere una linea di ritorno dati quando si usa un alimentatore separato. Ad esclusione di multiCLASS (lettori RP), richiede un modulo di espansione [ RS232, RS485, USB, da UART a UART]. GPIO sta per ingresso/uscita di tipo generale. Uscita tamper. Quando attivata, uscita a negativo (predefinito).
**** Dipende dalla configurazione del lettore. Per ulteriori informazioni in merito vedere le configurazioni HTOG Wiegand e Clock-and-Data. 2009 HID Global Corporation. All rights reserved. INSTALLATION GUIDE 5 iCLASS RK40, RWK400, RPK40 6404-901 A.1 P1-1 P1-2
(GRN) LED P1-3 P1-4 P1-5 P1-6 P1-7
(RTN)
+VDC
* (SHLD) LED P2-7 P2-6 P2-5 P2-4 P2-3 P2-2 P2-1
GPIO1 (RS232-T / RS485-A / HADP-OSDP-A / USB-5V / UART-T) GPIO2 (RS232-R / RS485-B / HADP-OSDP-B / USB-D+ / UART-R)
**** Wiegand1/
**** Wiegand0/
GPIO3 (RS485-Z/USB-D-) GPIO4 (RS485-Y) GPIO/
** [RS232RS485USBUART to UART]multiCLASS (RP)
(HTOG)WiegandClock-and-Data P1-1 P1-2 P1-3 P1-4 P1-5 P1-6 P1-7
(GRN) LED
(RTN)
+VDC
* (SHLD) LED P2-7 P2-6 P2-5 P2-4 P2-3 P2-2 P2-1
GPIO1 (RS232-T / RS485-A / HADP-OSDP-A / USB-5V / UART-T)
GPIO2 (RS232-R / RS485-B / HADP-OSDP-B / USB-D+ / UART-R)
**** Wiegand 1 /
**** Wiegand 0 /
GPIO3 (RS485-Z/USB-D-)
GPIO4 (RS485-Y)
** multiCLASSRP [RS232RS485USBUART UART]
GPIO /
HTOG Wiegand P1-1 P1-2 P1-3 P1-4 P1-5 P1-6 P1-7
(GRN) LED
(RTN)
+VDC
* (SHLD) LED P2-7 P2-6 P2-5 P2-4 P2-3 P2-2 P2-1
** GPIO1 (RS232-T /RS485-A / HADP-OSDP-A / USB-5V / UART-T)
** GPIO2 (RS232-R / RS485-B / HADP-OSDP-B / USB-D+ / UART-R)
**** Wiegand Data 1 / Clock
**** Wiegand Data 0 / Data
** GPIO3 (RS485-Z/USB-D-)
** GPIO4 (RS485-Y) GPIO General Purpose Input/Output( ) .
** multiCLASS(RP ) , [ RS232, RS485, USB, UART to UART ] .
**** . HTOG Wiegand Clock-and-Data . P1-1 P2-7
GPIO1 (RS232-T / RS485-A / HADP-OSDP-A / USB-5V / UART-T) P1-2 P1-3 P1-4 P1-5 P1-6 P1-7
(GRN)
* (SHLD) P2-6 P2-5 P2-4 P2-3 P2-2 P2-1
GPIO2 (RS232-R / RS485-B / HADP-OSDP-B / USB-D+ / UART-R)
**** Wiegand 1 /
**** Wiegand 0 /
GPIO3 (RS485-Z/USB-D-) GPIO4 (RS485-Y)
, . multiCLASS ( RP), [ RS232, RS485, USB, UART UART ]
GPIO - . ( ).
**** . Wiegand Clock-and-Data. 6 INSTALLATION GUIDE 2009 HID Global Corporation. All rights reserved. 6404-901 A.1 3 Install Reader to Backplate RK40, RWK400, RPK40 iCLASS instalacin dEl lEctor En la Placa PostErior installation du lEctEur sur la PlaquE arrirE instalao do lEitor na Placa trasEira lEsEr an dEr rckPlattE anbringEn installazionE dEl lEttorE a controPiastra 4 Power & Testing Turn power on Encienda la unidad Mettez sous tension Ligue a energia Einschalten Accendere EncEndido y PruEba alimEntation Et tEsts EnErgia E tEstE stromvErsorgung und tEstEn accEnsionE E Prova Test card Pruebe la tarjeta Testez la carte Teste o carto Karte testen Provare la tessera 2009 HID Global Corporation. All rights reserved. INSTALLATION GUIDE 7 iCLASS RK40, RWK400, RPK40 6404-901 A.1 Expansion Module Installation instalacin dEl mdulo dE ExPansin installation dEs modulEs dExtEnsion instalao do mdulo dE ExPanso installation dEr ErwEitErungsmodulE installazionE dEi moduli di EsPansionE m P Expansion Modules connect to terminal readers, install when power is off. Only multiCLASS pigtail readers provide prox expansion module capabilities. RS232, RS485, and UART expansion modules are not compatible with multiCLASS (RP readers). Los mdulos de expansin se conectan con los lectores de borne, se deben instalar cuando est apagada la energa. Slo los lectores flexibles multiCLASS son compatibles con el mdulo de expansin de proximidad. Los mdulos de expansin RS232, RS485 y UART no son compatibles con multiCLASS (lectores RP). Les modules dextension se connectent aux lecteurs bornier. Installez-les lorsque lappareil est hors tension. Seuls les lecteurs avec cble multiCLASS acceptent les modules dextension Prox. Les modules dextension RS232, RS485 et UART ne sont pas compatibles avec les lecteurs multiCLASS (lecteurs RP). Mdulos de expanso conectados aos leitores do terminal, instale quando estiver desligado. Apenas leitores de cabo flexvel multiCLASS fornece os recursos do mdulo de expanso prox. Os mdulos de expanso RS232, RS485 e UART no so compatveis com multiCLASS (leitores RP). Erweiterungsmodule werden an Terminal-Leser angeschlossen und bei ausgeschaltetem Gert installiert. Nur multiCLASS-Pigtail-Leser bieten Prox-Erweiterungsmodulfhigkeiten. RS232-, RS485- und UART-Erweiterungsmodule sind nicht mit multiCLASS (RP-Leser) kompatibel. I moduli di espansione sono collegati ai terminali dei lettori; installare quando spenti. Solo i mettori multiCLASS con cavo flessibile prevedono funzioni con modulo di espansione prox. I moduli di espansione RS232, RS485 e UART non sono compatibili con multiCLASS (lettori RP). ProxmultiCLASS RS232RS485UART multiCLASS (RP) multiCLASS prox RS232RS485 UART multiCLASSRP
. . multiCLASS (Pigtail) Prox . RS232, RS485 UART multiCLASS(RP ) . . multiCLASS proximity . RS232, RS485 UART multiCLASS ( RP). Part #
N de componente n PEa n teilenr PartE n
. 3122anb - uart 3122anE - rs232 3123anE - rs485 3123anm - HadP/osdP 3124anE - usb 3126anE - Hid Prox 3127anE - indala Prox 3128ANE - Em Prox 3170anE - Hi-o BEEP GRN RTN
+VDC SHLD RED HOLD GPI01 GPI02 OC/TMPR DATA1 DATA0 GPI03 GPI04 BEEP GRN RTN
+VDC SHLD RED HOLD GPI01 GPI02 OC/TMPR DATA1 DATA0 GPI03 GPI04 Expansion Module CAUTION: Once installed, do not remove expansion modules. PRECAUCIN: Tras la instalacin, no se deben quitar los mdulos de expansin. ATTENTION : une fois installs, les modules dextension ne doivent pas tre retirs. CUIDADO: Depois da instalao, no remova os mdulos de extenso. VORSICHT: Installierte Erweiterungsmodule nicht wieder entfernen. AVVISO: una volta completata linstallazione, non rimuovere i moduli di espansione.
: . 8 INSTALLATION GUIDE 2009 HID Global Corporation. All rights reserved. 6404-901 A.1 Optional Features RK40, RWK400, RPK40 iCLASS caractErsticas oPcionalEs CaractristiquEs En oPtion rEcursos oPcionais oPtionalE FEaturEs Funzioni oPzionali Expansion Modules provide optional functionality for all terminal readers. 3122ANB - UART to UART, 3122ANE - RS232, 3123ANE - RS485 (Full), 3123ANH - RS485 (Half), 3123ANM - HadP/osdP, 3124ANE - USB, 3126ANE - HID Prox, 3127ANE - Indala Prox, 3128ANE - EM Prox, 3170ANE - Hi-o Open Collector Output - Controls an external device (16 VDC Max) operating in Host Mode only. Sink - 40mA / Source - 1mA. See the iCLASS Application Note for details. Optical Tamper - A configuration card is necessary to activate the Optical Tamper. Once activated, and when the mounting plate is removed, the Optical Tamper is activated. Contact HID Technical Support for Optical Tamper options. See Tamper Application Note, AN0112. Configuration Cards - With the use of configuration cards, the reader can be modified to meet the specific requirements of an installation. Configuration options include; audio visual, CSN outputs and keypad outputs. Contact HID Technical Support for all reader configuration options. Hold Input - when asserted, this line either buffers a card or disables a card read until released, as configured. Los mdulos de expansin proporcionan a todos los lectores de borne salidas opcionales. 3122ANB - UART a UART, 3122ANE - RS232, 3123ANE/3123ANH - RS485, 3123ANM - HADP/OSDP, 3124ANE - USB, 3126ANE - HID Prox, 3127ANE Indala Prox, 3128ANE - EM Prox, 3170ANE - Hi-O Salida a colector abierto: controla un dispositivo externo (16 VCC mx.) que funciona nicamente en Modo Host. Disipacin de corriente: 40mA / Fuente: 1mA. Para obtener ms informacin, consulte la Nota de Aplicacin de iCLASS. Interruptor de sabotaje ptico: la tarjeta de configuracin acciona el interruptor de sabotaje ptico. Una vez accionado, cuando se retira la placa posterior del lector, se activa un interruptor de sabotaje ptico. Comunquese con el Centro de Asistencia Tcnica de HID para conocer las opciones de interruptores de sabotaje ptico. Tarjetas de configuracin: el uso de las tarjetas de configuracin permite que el lector se pueda modificar para cumplir con los requisitos especficos de una instalacin. Las opciones de configuracin incluyen salidas de audio, visuales, CSN y teclado numrico. Comunquese con el Centro de Asistencia Tcnica de HID para conocer todas las opciones de configuracin. Entrada de retencin: cuando se activa, esta lnea almacena una tarjeta en memoria intermedia o anula su configuracin de lectura hasta que sea desactivada. 3122ANB - UART UART, 3122ANE - RS232, 3123ANE/3123ANH - RS485, 3123ANM - HADP/OSDP, 3124ANE - USB, 3126ANE - HID Prox, 3127ANE - Indala Prox, 3128ANE - EM Prox, 3170ANE - Hi-O Sortie collecteur ouvert - contrle un dispositif externe ( 16 Vcc max, -40mA). Voir la note dapplication iCLASS pour de plus amples dtails. Les modules dextension fournissent des fonctionnalits optionnelles pour tous les lecteurs bornier. Autoprotection optique Une carte de configuration est ncessaire pour activer lautoprotection optique. Une fois que celle-ci a t active, lautoprotection optique se dclenche lorsque la plaque de montage est enleve. Contactez le support technique de HID pour connatre les options dautoprotection optique. Cartes de configuration Les cartes de configuration permettent de modifier le fonctionnement du lecteur pour satisfaire aux exigences spcifiques dune installation. Les options de configuration comprennent les fonctions audiovisuelles ainsi que les sorties CSN et les sorties de clavier. Contactez le support technique de HID pour connatre lensemble des options de configuration du lecteur. Entre Hold - Lorsquelle est active, cette ligne met une carte en mmoire tampon ou dsactive la lecture de carte lorsque lentre est active, selon la configuration dfinie. Mdulos de expanso oferecem opes funcionais para todos os leitores com terminais (borneiras). 3122ANB UART to UART, 3122ANE RS232, 3123ANE/3123ANH RS485, 3123ANM HADP/OSDP, 3124ANE USB, 3126ANE HID Prox, 3127ANE Indala Prox, 3128ANE - EM Prox, 3170ANE HiO Sada do coletor aberta controla o dispositivo externo (mx. 16 VCC) operando somente no modo Host. Dissipador 40mA / Fonte 1mA. Veja a observao iCLASS de aplicao para detalhes. Optical Tamper Um carto de configurao necessrio para ativar o Optical Tamper (detector tico). Uma vez acionado, quando se retira a placa traseira do leitor, o Optical Tamper ser ativado. Contate o suporte tcnico da HID para obter as opes do Optical Tamper. Cartes de configurao com o uso de cartes de configurao, o leitor pode ser modificado para atender aos requisitos especficos de uma instalao. As opes de configurao incluem udio-
visual, sadas de CSN e sadas de teclado. Contate o Suporte Tcnico HID para obter todas as opes de configurao do leitor. Entrada Hold quando ativada, essa linha ou armazena um carto ou desabilita a leitura de um carto at que seja liberada, conforme configurada. Erweiterungsmodule bieten zustzliche Funktionen fr alle Leser. 3122ANB - UART zu UART, 3122ANE - RS232, 3123ANE/3123ANH - RS485, 3123ANM - HADP/OSDP, 3124ANE - USB, 3126ANE - HID Prox, 3127ANE - Indala Prox, 3128ANE - EM Prox, 3170ANE - Hi-O Open-Collector-Ausgang steuert ein externes Gert (max. 16 VDC), ausschlielich ber serielle Schnittstelle. Sink - 40 mA / Quelle - 1 mA. Einzelheiten sind im iCLASS-Anwendungshinweis enthalten. Wenn nach Aktivierung der Konfigurationskarte die Montageplatte des Lesers entfernt wird, wird eine Manipulationswarnung ausgegeben. Optische Manipulationssicherung zur Aktivierung der optischen Manipulationssicherung ist eine Konfigurationskarte erforderlich. Wenn nach Aktivierung der Konfigurationskarte die Montageplatte des Lesers entfernt wird, wird eine Manipulationswarnung ausgegeben. Informationen zu den Konfigurationsoptionen der optischen Manipulationssicherung sind ber den technischen Support von HID erhltlich. Konfigurationskarten durch die Verwendung von Konfigurationskarten kann der Leser modifiziert werden, um die jeweiligen Anforderungen einer Installation zu erfllen. Zu den Konfigurationsoptionen gehren audiovisuelle Einstellung, CSN-Ausgnge und Tastenfeld-Ausgnge. Informationen zu den Konfigurationsoptionen der Leser sind ber den technischen Support von HID erhltlich. Hold-Eingang wenn diese Funktion aktiviert ist, werden die Kartendaten entweder zwischengespeichert oder die Lesekonfiguration der Karte wird gesperrt, je nach Konfiguration. 2009 HID Global Corporation. All rights reserved. INSTALLATION GUIDE 9 iCLASS RK40, RWK400, RPK40 6404-901 A.1 I moduli di espansione forniscono funzionalit aggiuntive a tutti i lettori. 3122ANB Da UART a UART, 3122ANE - RS232, 3123ANE/3123ANH - RS485, 3123ANM - HADP/OSDP, 3124ANE - USB, 3126ANE - HID Prox, 3127ANE - Indala Prox, 3128ANE - EM Prox, 3170ANE - Hi-O Uscita collettore aperto Controlla un dispositivo esterno (massimo 16 V c.c.) che funziona solo in modalit host. Sink - 40mA / Source - 1mA. Per dettagli in merito, vedere la nota applicativa iCLASS. Tamper ottico per lattivazione del tamper ottico necessaria una tessera di configurazione. Una volta attivato, se la piastra posteriore viene rimossa, il dispositivo viene attivato. Contattare il supporto tecnico HID per opzioni relative al tamper ottico. Tessere di configurazione tali tessere consentono di modificare il lettore in modo da rispondere agli specifici requisiti di uninstallazione. Le opzioni di configurazione includono: audio-visivo, output del numero di serie della scheda e output della tastiera. Contattare il supporto tecnico HID per tutte le opzioni di configurazione del lettore. Ingresso di tipo hold Quando viene attivata, questa linea memorizza in un buffer una tessera o disattiva la lettura della tessera fino al rilascio, come configurato. 3122ANB - UART to UART3122ANE - RS2323123ANE/3123ANH - RS4853123ANM - HADP/OSDP3124ANE - USB3126ANE - HID Prox3127ANE - Indala Prox3128ANE - EM Prox, 3170ANE - Hi-O
- ( 16 VDC) - 40mA / - 1mA iCLASS
HID
- CSN HID
3122ANB - UART UART3122ANE - RS2323123ANE/3123ANH - RS4853123ANM - HADP/OSDP3124ANE - USB3126ANE - HID Prox3127ANE - Indala Prox3128ANE - EM Prox, 3170ANE - Hi-O
- 16 VDC - 40mA/ - 1mA iCLASS
- HID
/CSN HID
. 3122ANB - UART to UART, 3122ANE - RS232, 3123ANE/3123ANH - RS485, 3123ANM - HADP/OSDP, 3124ANE - USB, 3126ANE - HID Prox, 3127ANE - Indala Prox, 3128ANE - EM Prox, 3170ANE - Hi-O
- ( 16 VDC) . , . - 40mA / - 1mA. iCLASS .
- . , . HID .
- , . LED , CSN . HID .
- , . 3122ANB - UART UART, 3122ANE - RS232, 3123ANE/3123ANH - RS485, 3123ANM - HADP/OSDP, 3124ANE - USB, 3126ANE - HID Prox, 3127ANE - Indala Prox, 3128ANE - EM Prox, 3170ANE - Hi-O
(16 ) -. 40 / 1 . iCLASS. ,
. ID.
: , SN ( ) . ID.
(Hold input) (
). 10 INSTALLATION GUIDE 2009 HID Global Corporation. All rights reserved. 6404-901 A.1 RK40, RWK400, RPK40 iCLASS Intentional Blank 2009 HID Global Corporation. All rights reserved. INSTALLATION GUIDE 11 UL Connect only to a Listed Access Control / Burglary power-limited power supply. These readers are intended to be used with listed (UL294) control equipment. Only the Wiegand communication protocol has been investigated by UL. FCC / Canada Radio Certification These devices comply with part 15 of the FCC rules. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Le fonctionnement est soumis aux deux conditions suivantes : (1) Ce dispositif ne peut pas causer de perturbations nuisibles et (2) ce dispositif doit accepter toute perturbation quelconque quil reoit, y compris des perturbations susceptibles de provoquer un fonctionnement indsirable. Les changements ou modifications nayant pas t expressment approuvs par la partie responsable de la conformit peuvent faire perdre lutilisateur lautorisation de faire fonctionner le matriel. CE Marking HID Global hereby declares that these proximity readers are in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Por el presente, HID Global declara que estos lectores de proximidad cumplen con los requisitos esenciales y otras disposiciones relevantes de la Directiva 1999/5/EC. HID Global dclare par la prsente que ces lecteurs proximit sont conformes aux exigences essentielles et aux autres stipulations pertinentes de la Directive 1999/5/CE. A HID Global, por meio deste, declara que estes leitores de proximidade esto em conformidade com as exigncias essenciais e outras condies da diretiva 1999/5/EC. HID Global besttigt hiermit, dass die Leser die wesentlichen Anforderungen und anderen relevanten Bestimmungen der Richtlinie 1999/5/EG erfllen. HID Global dichiara che i lettori di prossimit sono conformi ai requisiti essenziali e ad altre misure rilevanti come previsto dalla Direttiva europea 1999/5/EC. Download copies of the R&TTE Declaration of Conformity (DoC) at http://certifications.hidglobal.com. Taiwan According to "Administrative Regulations on Low Power Radio Waves Radiated Devices" Without permission granted by the DGT, any company, enterprise, or user is not allowed to change frequency, enhance transmitting power or alter original characteristic as well as performance to a approved low power radio-frequency devices. The low power radio-frequency devices shall not influence aircraft security and interfere legal communications; If found, the user shall cease operating immediately until no interference is achieved. The said legal communications means radio communications is operated in compliance with the Telecommunications Act. The low power radio-frequency devices must be susceptible with the interference from legal communications or ISM radio wave radiated devices. Japan MIC
(EMCETSI301-489) Singapore Approved by IDA for use in Singapore. DA103548 Models: 613xB, 613yAxN, 613yAxD, 613yAxA ACCESS experience. HID, HID Global, iCLASS, multiCLASS and Indala are the trademarks or registered trademarks of HID Global Corporation in the U.S. and other countries. 2009 HID Global Corporation. All rights reserved. hidglobal.com 6404-901 Rev A.1 Patent Pending Check reader label for current regulatory approvals. HID Global North America 15370 Barranca Parkway Irvine, CA 92618 USA Phone:
800 237 7769 Support: 866-607-7339 949-732-2120 Fax:
Email:
tech@hidglobal.com Asia Pacic Europe, Middle East & Africa 19/F 625 Kings Road NorthPoint, Island East Hong Kong Phone:
852 3160 9800 Support: 852 3160 9833 852 3160 4809 Fax:
Email:
asiasupport@hidglobal.com Phoenix Road Haverhill, Suolk CB9 7AE England Phone: +44 (0) 1440 714 850 Support: +44 (0) 1440 711 822
+44 (0) 1440 714 840 Fax:
Email:
eusupport@hidglobal.com
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2009-10-19 | 0.125 ~ 0.125 | DCD - Part 15 Low Power Transmitter Below 1705 kHz | Original Equipment |
2 | 13.56 ~ 13.56 | DXX - Part 15 Low Power Communication Device Transmitter |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 2 | Effective |
2009-10-19
|
||||
1 2 | Applicant's complete, legal business name |
HID Global Corporation
|
||||
1 2 | FCC Registration Number (FRN) |
0005004122
|
||||
1 2 | Physical Address |
611 Center Ridge Dr.
|
||||
1 2 |
Austin, Texas 78753
|
|||||
1 2 |
United States
|
|||||
app s | TCB Information | |||||
1 2 | TCB Application Email Address |
t******@siemic.com
|
||||
1 2 | TCB Scope |
A1: Low Power Transmitters below 1 GHz (except Spread Spectrum), Unintentional Radiators, EAS (Part 11) & Consumer ISM devices
|
||||
app s | FCC ID | |||||
1 2 | Grantee Code |
JQ6
|
||||
1 2 | Equipment Product Code |
RPK40C
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 2 | Name |
R****** C********
|
||||
1 2 | Title |
Compliance Engineering Manager
|
||||
1 2 | Telephone Number |
303-4********
|
||||
1 2 | Fax Number |
303-4********
|
||||
1 2 |
r******@hidglobal.com
|
|||||
app s | Technical Contact | |||||
1 2 | Firm Name |
SIEMIC Lab
|
||||
1 2 | Name |
S**** L******
|
||||
1 2 | Physical Address |
2206 ringwood Ave
|
||||
1 2 |
San Jose, Colorado 95131
|
|||||
1 2 |
San Jose, California 95131
|
|||||
1 2 |
United States
|
|||||
1 2 | Telephone Number |
40852********
|
||||
1 2 | Fax Number |
40852********
|
||||
1 2 |
s******@siemic.com
|
|||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 2 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 2 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 2 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 2 | Equipment Class | DCD - Part 15 Low Power Transmitter Below 1705 kHz | ||||
1 2 | DXX - Part 15 Low Power Communication Device Transmitter | |||||
1 2 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | RFID Reader/Keypad | ||||
1 2 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 2 | Modular Equipment Type | Does not apply | ||||
1 2 | Purpose / Application is for | Original Equipment | ||||
1 2 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | Yes | ||||
1 2 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 2 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 2 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 2 | Firm Name |
SIEMIC Laboratories
|
||||
1 2 | Name |
L****** B********
|
||||
1 2 | Telephone Number |
408-5********
|
||||
1 2 | Fax Number |
408-5********
|
||||
1 2 |
L******@siemic.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | CC | 0.12500000 | 0.12500000 | ||||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
2 | 1 | 15C | CC | 13.56000000 | 13.56000000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC