FCC ID: 2AVLE-HT-JRT1200K Wifi range extender

1200M Dual Wifi range extender Mobile terminal operating manual V1.0 Mobile terminal operating manual Preparations Plug the device into a power outlet and the indicator will flash when the device is powered on. Mobile phone settings 1.The mobile phone searches for the Wi-Fi signal and connects to the signal of the name "wlan_repeater"(without quotes)(as shown in Figure 1). There is no password by default. 2.Open the mobile browser and enter "192.168.10.1" (without quotes). The default password is "admin" (without quotes), click here to login(as shown in Figure 2 and Figure 3). AVAILABLE NETWORKS Wlan_repeater 192.168.10.1 Connected (no Internet access) Login 192.168.10.1 Figure 1 Figure 2 1 Mobile terminal operating manual Figure 3 Note: Some mobile phones will have the WLAN assistant prompts (as shown in Figure 4), click

"CONNECT", otherwise the settings will not be completed. This WLAN network has no Internet access.Connect anyway?

CANCEL CONNECT Figure 4 3.The first time you log in to the configuration page, the page will go to the setup wizard page (as shown in Figure 5 ),password is the default admin, if you want to change the password, you can click on "admin" to modify, then click [Next], select the repeater in the working mode (as shown in Figure 6), click [Next]. And then the repeater will automatically scan the surrounding wireless signal (as shown in Figure 7 and Figure 8). 2 Mobile terminal operating manual 192.168.10.1/view/admin_wizar 1 192.168.10.1/view/admin_wizar 1 System Work mode Setting Complete System Work mode Setting Complete Password admin Work mode Repeater Next Figure 5 Back Next Figure 6 192.168.10.1/view/admin_wizar 1 192.168.10.1/view/admin_wizar 1 System Work mode Setting Complete WiFi name: HonortekWifi Encryption: WPA-PSK2 WiFi password:

Exterded 2.4G: Wlan_repeater Exterded 5G: Wlan_repeater Back Scaning... Scan Next Figure 7 3 WiFi name: HonortekWifi Encryption: WPA-PSK2 WiFi password:

Exterded 2.4G: Wlan_repeater Exterded 5G: Wlan_repeater Back Re-scan Next QL-2G 2 2 CLOVER 2 QLJS-2G 2 QL-2G 5 QLJS-5G 2 QL-2G Figure 8 Mobile terminal operating manual 4.In the "Routing Network Signal List", click the Wi-Fi signal you want to relay, and enter the password of the original Wi-Fi signal in "Wi-Fi password" (as shown in Figure 9). Click the [Next] button in Figure 9, and then click the [save] button (as shown in Figure 10), the device will be applied and restarted(as shown in Figure 11). Wait for one minute after restarting. If the indicator light is steady blue, it means that the repeater has been successfully relayed. 192.168.10.1/view/admin_wizar 1 192.168.10.1/view/admin_wizar 1 192.168.10.1/view/admin_wizar 1 System Work mode Setting Complete System Work mode Setting Complete System Work mode Setting Complete WiFi name: QLJS-5G Encryption: WPA-PSK2 WiFi password:

Exterded 2.4G: QLJS-5G_EXT2.4G Exterded 5G: QLJS-5G_EXT5G Back Re-scan Next 2 ChinaNet-AHTA QLJS-5G 5 2 QL-2G_ext 5 QL-5G QL-5G 5 System:

Password admin System:

Password admin Work mode Repeater Work mode Repeater Wi-Fi Setup WiFi name QLJS-5G QLJS-5G_EXT2.4G 2.4G SSID 5G SSID QLJS-5G_EXT5G Encryption WPA-PSK2 Password trylong666 Successful configuration!

configuration is in effect, please login again later. Wi-Fi Setup WiFi name QLJS-5G QLJS-5G_EXT2.4G 2.4G SSID 5G SSID QLJS-5G_EXT5G Encryption WPA-PSK2 Password trylong666 Back Save Back Save Figure 9 Figure 10 Figure 11 4 Mobile terminal operating manual Note: After configuration, the device will reboot and the Wi-Fi name will become

"xxxx_EXT2.4G"/"xxxx_EXT5G". (xxxx is the name of the original Wi-Fi signal, the password is the password of the original Wi-Fi signal). If the repeater works in "Repeater mode", and you want to use the LAN network interface of the repeater. you have to insert the network cable after the configuration is completed and the indicator light is steady blue. 5.If you want to modify the repeater Wi-Fi name and password, you need to connect to the Wi-Fi after successful configuration, and then re-enter the configuration interface, Click the "Wi-Fi Setup" to Setup (as shown in Figure 12 and Figure 13). 192.168.10.1/view/admin_wizar 1 192.168.10.1/view/admin_wizar 1 Wireless users Wi-Fi Setup Signal strength Advanced settings Wi-Fi Setup 2.4G Wi-Fi Settings Wi-Fi ON/OFF:

Hide SSID:

Extended 2.4G:

Encryption:

2.4G passwd:

ON OFF QLJS-5G_EXT2.4G WPA2-PSK 5G Wi-Fi Settings Wi-Fi ON/OFF:

Hide SSID:

Extended 5G:

Encryption:

5G passwd:

ON OFF QLJS-5G_EXT5G WPA2-PSK Figure 12 Figure 13 5 Mobile terminal operating manual Set the 2.4G wireless SSID in "Extended 2.4G", set the 5.8G wireless SSID in

"Extended 5G", and set the wireless password in "Wi-Fi password" (as shown in Figure 15). 6.Mode description:

(1) Repeater:

The repeater mode refers to amplifying the original Wi-Fi signal and then transmitting a new Wi-Fi signal (the new signal name can be the same as or different from the original Wi-Fi signal) , endlessly expand your wireless network to cover large areas and improve performance.

(2) AP mode:

AP mode: Wireless access point mode is a working mode that converts wired to Wi-Fi wireless. It is usually used in an environment where only wired access has no Wi-Fi signal in the current environment. Settings: Insert the network cable into the network interface of the device, select AP mode of the Work mode (as shown in Figure 14), and click [Next] to enter the Wireless Configuration page. Set the 2.4G wireless SSID in "Extended 2.4G", set the 5.8G wireless SSID in "Extended 5G", and set the wireless password in "Wi-Fi password" (as shown in Figure 15). After clicking [Save], the device will restart and apply the new configuration work (as shown in Figure 16). In AP mode, the device indicator will be blue when the start-up is complete. 6 Mobile terminal operating manual System Work mode Setting Complete System Work mode Setting Complete Work mode AP mode Back Next Exterded 2.4G:

Exterded 5G:

text text Encryption: WPA/WPA2 Mix WiFi password:

Back Next System Work mode Setting Complete System:

Password admin Work mode AP mode Wi-Fi Setup 2.4G SSID 5G SSID Encryption WPA/WPA2 Mix Password 12345678 text text Back Save Figure 14 Figure 15 Figure 16

(3) Router mode:

Routing mode: Wireless router mode, you can set PPPOE, static IP access, automatic acquisition, usually used for modem dialing Internet access or static IP access mode. Settings: Insert the network cable into the network interface of the device, select "Router mode of the "Work mode"(as shown in Figure 17), and click [Next] to enter the "Routing Configuration" page. According to the network access mode, select "DHCP client",

"sstatic IP" ,"PPPOE", in the "Internet settings". Set the 2.4G wireless SSID in

"Extended 2.4G", set the 5.8G wireless SSID in Extended 5G and set the wireless password in "Wi-Fi password" (as shown in Figure 18). After clicking [Save], the device will restart and apply the new configuration work (as shown in Figure 19). In the routing mode, the device indicator will be blue when the start-up is completed. 7 Mobile terminal operating manual 192.168.10.1/view/admin_wizar 1 192.168.10.1/view/admin_wizar 1 192.168.10.1/view/admin_wizar 1 System Work mode Setting Complete System Work mode Setting Complete System Work mode Setting Complete Work mode Router mode Back Next Internet settings DHCP client Exterded 2.4G:

Exterded 5G:

DHCP client Static IP PPPoE Encryption: WPA/WPA2 Mix WiFi password:

Back Next System:

Password admin Work mode Router mode Wi-Fi Setup 2.4G SSID 5G SSID Encryption WPA/WPA2 Mix Password 12345678 text text Figure 17 Figure 18 Figure 19 Back Save Frequently Asked Questions 1.After the device "repeater mode" configuration is complete, the indicator light flashes blue and the repeater signal cannot be connected to the Internet. A: The blue indicator light flashes to indicate that the repeater is not successfully paired, which may be caused by these reasons:

(1)When the wireless router is filled in, the password is incorrectly entered. Please check if the password is correct.

(2)the original signal is too weak. Please install your mobile device to a better Wi-Fi signal area to ensure the connection speed of the repeater signal and the Wi-Fi coverage signal. 8 Mobile terminal operating manual 2.After the setting is completed, the saving is unsuccessful, and the device prompts that there is no network?

A:Some mobile phones have the assistant prompts (as shown in Figure 4), click

"CONNECT", otherwise the settings will not be completed. If the save is not successful, you will need to reconnect Wi-Fi_REPEAPTER Wi-Fi and reset it. This WLAN network has no Internet access.Connect anyway?

CANCEL CONNECT Figure 20 3.After using the device normally, you want to log in to the device configuration parameters. APress and hold the WPS/Reset button for 6 seconds, the device will be restored to the factory settings, the device indicator light will flash blue, the wired device or Wi-Fi connection will be connected to the WLAN_REPEAPTER signal, and the browser will enter 192.168.10.1 to reconfigure the device. 4.Why is the WLAN-REPEATER Wi-Fi name not received after the setting is completed? Why is the browser page not responding after the setup is complete? Why is Wi-Fi disconnected?

9 Mobile terminal operating manual A: After the setting is completed, the device will take effect with the new configuration. The default factory configuration will no longer be used. Please connect the newly set Wi-Fi name signal.It is recommended that you change the Wi-Fi name of the repeater to the same Wi-Fi name and password as the wireless router. When your mobile phone switches back and forth between the Wi-Fi router and the repeater, the mobile Wi-Fi will not dropped and seamlessly switch Wi-Fi!

5.After the configuration of the repeater mode is complete, the indicator light is blue, but the network port of the wired device cannot access the Internet. A: The default state of the device is route mode, and the assigned address is only used as a configuration device. After the repeater is successfully relayed,restarting the wired network card or re-plugging the network cable, you can access the network. 6.What can't be relayed successfully?

A:

(1)The original wireless router Wi-Fi name or password has a special symbol.

(2)Some Wi-Fi relays are unsuccessful because they are restricted to relay or weak signals. 7.Which Wi-Fi can be forwarded by the repeater?

A:

(1)Any mainstream wireless router on the market.

(2)Mobile hotspots.

(3)Wireless AP, 4G wireless router, etc. 10 Mobile terminal operating manual FCC Warnning:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. 10

LABEL AND LOCATION Wifi range extender Model No.: HT-JRT1200K FCC ID: 2AVLE-HT-JRT1200K This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Label And Location

HK HONORTEK CO., LIMITED Add: No.9 Wugang Road,Henggang Street,Longgang District,Shenzhen,China Tel: +86 15626574158 Fax: /

Date: 2020/01/10 Dear Sir/Madam, We, HK HONORTEK CO., LIMITED Hereby declares the following statement for Federal Communications Commission, PCB board, circuit, structure and internal of these model(s) are the same, Only model number is different for these model:

Product name: Wifi range extender Model no.: HT-JRT1200K, LN1078TS Sincerely, Name/Title Tommy Xu /Manager Company:HK HONORTEK CO., LIMITED Address: No.9 Wugang Road,Henggang Street,Longgang District,Shenzhen,China Phone: +86 15626574158 E-Mail: sales2@honor-tek.com

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 Date: 2020/01/10 TO WHOM IT MAY CONCERN Pursuant to Paragraphs 0.457 and 0.459 of the Commissions Rules (47 C.F.R.) and Section 552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products:

FCC ID 2AVLE-HT-JRT1200K HT-JRT1200K, LN1078TS For the product stated above, we request that the following information be held confidential;

Model name Exhibits Long-Term Short-Term Short-Term Confidentiality Confidentiality Confidentiality Days External Photos Internal Photos Block Diagram Schematics Test Setup Photos Users Manual Parts List Tune Up Operational Descriptions The long-term confidentiality exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Name/Title Company:

Address:

Phone:

E-Mail:

Tommy Xu /Manager HK HONORTEK CO., LIMITED No.9 Wugang Road,Henggang Street,Longgang District,Shenzhen, China

+86 15626574158 sales2@honor-tek.com

HK HONORTEK CO., LIMITED No.9 Wugang Road,Henggang Street,Longgang District,Shenzhen,China UNII Device Declaration Letter To whom it may concern:

We have declared below featured for FCC equipment authorization, Device FCC ID: 2AVLE-HT-JRT1200K

(1) DFS Device:

Master N/A Client with Radar detection capability Client without radar detection capability,

(2) Active / Passive Scanning , adhoc mode access point capability Frequency Band (MHz) 5180-5240 5190-5230 5210-5210 5745-5825 5755-5795 5775-5775 Active Scanning

(the device can transmit a probe

(beacon)) Yes Yes Yes Yes Yes Yes No No No No No No passive scanning

(where the device is can listen only with no probes) No No No No No No Yes Yes Yes Yes Yes Yes

(3) Country code selection ability Yes If yes, pls explain how it was implemented:

No

(4) Meet 15.202 requirement Yes No pls check below :

Ad Hoc Mode capability Access point capability Yes Yes Yes Yes Yes Yes No No No No No No Yes Yes Yes Yes Yes Yes No No No No No No A master device is defined as a device operating in a mode in which it has the capability to transmit without receiving an enabling signal. In this mode it is able to select a channel and initiate a network by sending enabling signals to other devices A client device is defined as a device operating in a mode in which the transmissions of the device are under control of the master. A device in client mode is not able to initiate a network.

(5) For client devices that have software configuration control to operate in different modes (active scanning in some and passive scanning in others) in different bands (devices with multiple equipment classes or those that operate on non-DFS frequencies) or modular devices which configure the modes of operations through software, the application must provide software and operations description on how the software and / or hardware is implemented to ensure that proper operations modes cannot be modified by end user or an installer. Apply Does not apply

(If apply, pls help to provide explanation on it was implement, and how software was controlled) Should you have any questions or comments regarding this matter, please have my best attention. Sincerely, Name/Title Company:

Address:

Phone:

Fax:

E-Mail:

Tommy Xu /Manager HK HONORTEK CO., LIMITED No.9 Wugang Road,Henggang Street,Longgang District,Shenzhen, China

+86 15626574158

sales2@honor-tek.com

HK HONORTEK CO., LIMITED No.9 Wugang Road,Henggang Street,Longgang District,Shenzhen,China Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 To whom it may concern:

01/10/2020 We, HK HONORTEK CO., LIMITED. the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behalf in all matters relating to applications for equipment authorization FCC ID:

2AVLE-HT-JRT1200K including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, Name/Title Company:

Address:

Phone:

E-Mail:

Tommy Xu /Manager HK HONORTEK CO., LIMITED No.9 Wugang Road,Henggang Street,Longgang District,Shenzhen, China

+86 15626574158 sales2@honor-tek.com

HK HONORTEK CO., LIMITED No.9 Wugang Road,Henggang Street,Longgang District,Shenzhen,China HK HONORTEK CO., LIMITED FCC ID: 2AVLE-HT-JRT1200K Model Number: HT-JRT1200K, LN1078TS DATE: 2020/01/09 To Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 We, HK HONORTEK CO., LIMITED declare ID:

2AVLE-HT-JRT1200K) doesnt have Ad Hoc mode function on non-US/Canada frequencies. In addition. The frequency selection feature is disabled by firmware for devices marked to the US/Canada. For DTS part of this device, only channels 1-11 will be used in North America, Country code selection is disabled. Should you have any questions or comments regarding this matter, please have my best attention. Best Regards!

this EUT

(FCC that Name/Title Tommy Xu /Manager Company:

HK HONORTEK CO., LIMITED Address:

No.9 Wugang Road,Henggang Street,Longgang District,Shenzhen,China Phone:

E-Mail:

+86 15626574158 sales2@honor-tek.com