FCC ID: BYM7000 Remote Transceiver

 

The RT7000 Remote Transceiver facilitates Base Station to Headset

communication. It uses a wired connection to the Base Station but

is wireless for Headset communication. Up to four RT7000s can be

connected to the Base Station for additional coverage.

TOOLS/EQUIPMENT REQUIRED

• Drill and drill bit set

• Screwdriver (Phillips #2), tape measure, pencil/maker

• Fish stick, cable ties, safety glasses, ladder

INSTALLATION, SETUP, AND OPERATION

1. Survey the premises to determine a good location to mount

the RT7000 (see Remote Transceiver RT7000 Notes on the next

page).

2. Once a good location is selected, route the Ethernet cable from

RT7000 TRANSCEIVER

Front View

the Base Station to the RT7000 location.

3. Loosely mount the Remote Transceiver in an optimal location

(until range tested with a roving headset using the Installation

Wizard via the Base Station in step 5.

4. Connect the Ethernet cable to the RJ45 port on the rear of the

RT7000 (see Fig. 2) and the other end to one of the available

ports on the Base Station (see Fig. 4 and Table 1).

4

3

1

2

5. At the Base Station LOG IN to the system, go to SYSTEM, then

the ADVANCED tab and select “Installation” from the drop-

down menu. Tap the “Start Installation Wizard” button.

This opens the Installation Wizard as shown in Fig. 3.

RT7000 TRANSCEIVER

Front View

RT7000 TRANSCEIVER

Rear View

Mounting Holes

RJ45 Port

for Ethernet cable

THIS SIDE UP

1

3

2

4

Fig. 1

RT7000 TRANSCEIVER

Rear View

Mounting Holes

RJ45 Port

for Ethernet cable

THIS SIDE UP

Fig. 2

NEXEO BASE STATION

PCBA (Partial)

REMOTE TRANSCEIVER

(RT7000)

J?300

Micro

USB

Fig. 3

J2003

1

1

J4500

J4501

J3000

J803

J804

Early

Warnings

1

J1400

Ethernet/

Network

J3200

Remote

XCVR 1

J3400

J3600

J3800

Remote

XCVR 2

Remote

XCVR 3

Remote

XCVR 4

1

J200

J?301

Serial

Debug

Remote

Switches

6. Follow the Transceiver Installation steps that follow. Once you

1

have used a headset in Reception Location Mode to walk the

USB

J805

premises to determine the mounting location is good, move

on to the next step. If the mounting location is not a good one,

move the Remote Transceiver to another location and repeat

steps 1 through 6, until a good location is found.

1

7. Drill two holes 6.625 inches (16.83 cm) apart along a horizontal

1

axis on the wall (avoid electrical or plumbing obstructions).

Timer Greet

Veh Detect 2

Install the provided hardware but do not tighten, leave a gap (~

¹/8th inch (3.2 mm)) between the screw heads and wall.

9. Align the RT7000 mounting holes with the two screws (Fig. 2).

Timer Greet

Veh Detect 1

Telephone

Interface

Alert

Inputs

8.

J801

J800

J201

J600

J802

1

1

1

1

Veh Detect

Inputs

Power

In

J1

GND

DC -

DC +

1

3

2

4

Vertical Mount Only

(this way up)

PCBA

Side View Detail

Transceiver (x4)

Power

Remote

Module 3

Remote

Module 1

Remote

Module 4

Remote

Module 2

Ethernet

(Network)

Fig. 4

HM ELECTRONICS, INC.

2848 Whiptail Loop, Carlsbad, CA 92010 USA

Phone: 1-800-848-4468 Fax: 858-552-0172

Website: www.hme.com Email: support@hme.com

Quick Reference Installation GuideHME# PUB - 000xxRev A 09/01/20RT7000 REMOTE TRANSCEIVER10. Mount the RT7000 over the screw heads until flush

against the wall, then slide it down onto the screws

to secure it in place and tighten hardware.

11. The other end of the Ethernet cable is connected

to the Base Station (see Fig. 4 and the Table 1 for

connections).

12. The Base Station provides power to the RT7000. So

when connected, the center LED in the circle on the

front of the RT7000 turns on solid green.

13. The peripheral LED around the circle initially flash-

es as the RT7000 completes a scan of the environ-

ment. Once the scan is finished, this peripheral LED

also turns solid green.

Note: This LED also flashes blue when the firmware

is updating.

14. The RT7000 is now operational. The Base Station

HOME screen also provides a color-coded visual

status (see "Transceivers" status in Fig. 5).

Tap "Transceivers" on the HOME screen for more details

(see Fig. 6).

Safety Notice

Fig. 5

Fig. 6

Remote Transceiver (RT7000) Notes:

• Mount the transceiver high in a central location to

headset usage.

• Maximize line of sight between the transceiver and

headsets in an area free from obstructions and

equipment/materials that can interfere with signal

propagation. These include walls, large metal ap-

pliances, hoods, and backsplashes, etc.

• Mount the transceiver vertically on a wall in the

upright position (see arrow on Transceiver rear). Do

NOT mount horizontally such as on a ceiling, this

will reduce the transceiver’s range.

• Signal propagation is strongest directly in front of

the Transceiver and then to the sides.

• The RT7000 uses an Ethernet (Cat5 or Cat6) cable.

Do not exceed 1000’ (304 m).

Large premises may require more than one Trans-

ceiver. Up to four Transceivers are supported by

one Base Station.

• Once connected to the Base Station, the LED in

•

2

2

1

the middle of the circle on the

transceiver front illuminates to

indicate it is turned on. One of

the outer LEDs (numbered 1 to

4) around the circle also turns

on (depending on which port the

Transceiver is connected to on

the Base Station, see Fig. 7). This

outer LED will initially flash as the Transceiver scans

for available channels before turning solid green

once a channel is found (on the Base Station HOME

screen, the "Transceivers" indicator is yellow while

scanning before turning green).

Fig. 7

3

4

Base Station RT7000 Ports

Connector #

Label

To

J3200

J3400*

J3600*

J3800*

Remote XCVR 1**

Remote XCVR 2**

Remote XCVR 3**

Remote XCVR 4**

Table 1

First RT7000

Second RT7000

Third RT7000

Fouth RT7000

* Only used if more than one RT7000 is required.

** LEDs (1 - 4) on the RT7000 Front (Fig. 7) correspond to the Remote

XCVR port number on the Base Station (Table 1 label).

CAUTION: Wear proper eye, ear, and body protection when

grinding, drilling or working with tools. Follow the manufactur-

er’s safety information and operational instructions for tools

and materials. Be aware of your surroundings. Failure to heed such

precautions can cause injury and/or property damage.

Hygiene, Health, and Safety

Part of this installation requires working within a restaurant/store

where food is prepared, and customers dine. Please consult the

restaurant/store manager, standard operating procedures and any

additional restaurant safety/advisory protocols available before be-

ginning work within the restaurant/store. Follow the instructions and

guidelines provided.

A copy of this guide and additional information

can be found by scanning this QR code.

HM ELECTRONICS, INC.

2848 Whiptail Loop, Carlsbad, CA 92010 USA

Phone: 1-800-848-4468

Fax: 858-552-0172

Website: www.hme.com

Email: support@hme.com

The HME logo and product names are regis-

tered trademarks of HM Electronics, Inc.

© 2020 HM Electronics, Inc. All rights reserved.REGULATORY COMPLIANCE

Applicant Name: HM Electronics, Inc.

Applicant Address: 2484 Whiptail Loop, Carlsbad CA 92010, United States

Manufacturer Name: HM Electronics, Inc.

Manufacturer Address: 2484 Whiptail Loop, Carlsbad CA 92010, United States

Country of Origin: USA

Brand: HME

Caution: All products are compliant with regulatory requirements detailed in this document when the user follows

all installation instructions and operating conditions per HME specifications.

Caution: Use of accessories and peripherals other than those recommended by HME may void the product's com-

pliance as well as the user's authority to operate the equipment.

Caution: All products are designed for use with the standard, integral or dedicated (external) antenna(s) that are

shipped together with the equipment. Any product changes or modifications will invalidate all applicable regulatory

certifications and approvals.

Caution: The use of software or firmware not supported/provided by HME products may result that the equipment is

no longer compliant with the regulatory requirements.

FCC NOTICE

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) This device must accept any interference received, including

interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to

Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate ra-

dio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communication. Operation of this equipment in a residential area is likely to cause harmful

interference, in which case the user will be required to correct the interference at his own expense.

Changes or modifications not expressly approved by HME could void the user’s authority to operate this equipment.

User Restriction in the 5Ghz band: The device for the band 5150-5250MHz is only for indoor

usage to reduce potential for harmful interference to co-channel mobile satellite systems.

FCC/IC/EC RF EXPOSURE WARNING

This product complies with FCC/IC/EC radiation exposure limits set forth for an uncontrolled environment.

Produits HME sont conformes aux limites IC d'exposition aux rayonnements définies pour un environnement non

contrôlé.

This product may not be co-located or operated in conjunction with any other antenna or transmitter.

Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnement en association avec une autre an-

tenne ou transmetteur.

To comply with FCC/IC/EC RF exposure requirements, this unit must be installed and operate at least 20 cm (8

inches) from any person.

Produits HME doivent être installés et utilisés avec distance minimum de 20cm entre le radiateur et votre corps.

3

© 2020 HM Electronics, Inc. All rights reserved.INDUSTRY CANADA COMPLIANCE STATEMENT

Avis de conformité à la réglementation d'Industrie Canada

Cet appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’ex-

ploitation est soumise aux deux conditions suivantes:

(1) cet appareil ne doit pas provoquer d’interféence, et

(2) cet appareil doit accepter toute interféence radioéectrique subie, mêe si l’interféence est susceptible d’en com-

promettre le fonctionnement.

Cet éetteur exempt de licence est éuipéd’une antenne intéré. Cet éetteur exempt de licence n’est pas autoriséà-

fonctionner avec une autre antenne.

Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnement en association avec une autre an-

tenne ou transmetteur.

Cet appareil numérique de la class[A] est conforme à la norme NMB-003 du Canada.

This Class[A] digital device complies with Canadian ICES-003.

Restrictions d'utilisation dans la bande 5 GHz: L’appareil pour la bande de 5150 a 5250MHz est concupour

usage a l’interieur seulement afin de reduire le potentiel d interferences pour les systemes mobiles par satellite qui

utilisent le meme canal.

User Restriction in the 5Ghz band: The device for the band 5150-5250MHz is only for indoor usage to reduce

potential for harmful interference to co-channel mobile satellite systems.

Jusqu’a nouvel ordre, les appareils faisant l’objet de la presente section ne doivent pas transmettre dans la bande

5600-5650 MHz, afin que les radars meteorologiques d’Environnement Canada fonctionnant dans cette bande

soient proteges.

Until further notice, devices subject to this Section shall not be capable of transmitting in the band 5600-5650MHz,

so that environmental weather radars operating in this band are protected.

KOREAN NOTICE

A급 기기 (업무용 방송통신기자재)

이 기기는 업무용(A급)으로 전자파적합기기로

서 판매자 또는 사용자는 이 점을 주의하시기

바라며, 가정외의 지역에서 사용하는 것을 목

적으로 합니다.

KCC 2.4Ghz and 5725-5850MHz warning: Life-related safety services cannot be provided because the radio

equipment may have radio interference.

해당 무선설비는 전파혼신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없음

AUSTRALIA COMPLIANCE STATEMENT

User Restriction in the 5Ghz band: This device is restricted to indoor use only when operating in 5150-5350MHz.

Until further notice, devices subject to this Section shall not be capable of transmitting in the band 5600-5650MHz,

so that environmental weather radars operating in this band are protected.

4

© 2020 HM Electronics, Inc. All rights reserved.NEW ZEALAND COMPLIANCE STATEMENT

User Restriction in the 5Ghz band: This device is restricted to indoor use only when operating in 5150-

5250MHz.

EUROPEAN UNION (CE MARK)

The CE marking indicates compliance with the following directives and standards, whenever applicable to the prod-

uct in question.

Directives:

- Radio Equipment Directive 2014/53/EU

- Electromagnetic Compatibility Directive 2014/30/EU

- Low Voltage Directive 2014/35/EU

- RoHS Directive 2011/65/EU and 2015/863/EU

Standards:

- EN55022/EN55032

- EN55024/ EN55035

- IEC/EN62368-1

- EN300328

- EN301893

- EN301489

- EN50581

Warning: This is a Class A product. In a domestic environment this product may cause radio interference in which

case the user may be required to take adequate measures.

User Restriction in the 5Ghz band: This device is restricted to indoor use only when operating in 5150-5350MHz

for below EU member states.

Caution: Although Europe allows 5600-5650Mhz band, these DFS channels 120, 124 and 128 must perform a 10

minutes radar scanning (also known as CAC - Channel Availability Check) before becoming an operating channel.

WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE)

The European Union (EU) WEEE Directive (2012/19/EU) places an obligation on producers (manufacturers, dis-

tributors and/or retailers) to take-back electronic products at the end of their useful life. The WEEE Directive covers

5

© 2020 HM Electronics, Inc. All rights reserved.most HME products being sold into the EU as of August 13, 2005. Manufacturers, distributors and retailers are

obliged to finance the costs of recovery from municipal collection points, reuse, and recycling of specified percent-

ages per the WEEE requirements.

INSTRUCTIONS FOR DISPOSAL OF WEEE BY USERS IN THE EUROPEAN UNION

The symbol shown below is on the product or on its packaging which indicates that this product was put on the

market after August 13, 2005 and must not be disposed of with other waste. Instead, it is the user’s responsibility

to dispose of the user’s waste equipment by handing it over to a designated collection point for the recycling of

WEEE. The separate collection and recycling of waste equipment at the time of disposal will help to conserve natu-

ral resources and ensure that it is recycled in a manner that protects human health and the environment. For more

information about where you can drop off your waste equipment for recycling, please contact your local authority,

your household waste disposal service or the seller from whom you purchased the product.

6

© 2020 HM Electronics, Inc. All rights reserved.

 

 

 

 

 

 

 

 

 

 

FCC label for model 7000 HM Electronics, Inc. | 2848 Whiptail Loop | Carlsbad, CA 92010 800.848.4468 | www.hme.com

 

 

Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: 08/27/2020 SUBJECT: FCC Application for (FCC ID: BYM7000) To Whom It May Concern:

We, the undersigned, hereby authorize David Zhang in Vista Laboratories, Inc. on our behalf, to apply to the Federal Communications Commission on our equipment with FCC ID BYM7000. Any and all lawful acts carried out by Vista Laboratories, Inc. on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, Clients signature:

Clients name: Douglas Paul Sieh Clients title: Electrical Compliance Engineering Supervisor Company Name: HM Electronics, Inc. Company Address: 2848 Whiptail Loop, Carlsbad, CA 92010, USA Main: +1-858-535-6000 Fax: +1-858-452-7207 HM Electronics, Inc. | 2848 Whiptail Loop | Carlsbad, CA 92010 800.848.4468 | www.hme.com